WARNING! Please read and understand this owner's ... - Sig Sauer

More documents

Recommendations

Info

MaintenanceServicing9.5 Care of the pistol 10 Service and repairsCAUTION!Neglecting the pistolPossibly damage to the pistol and bodilyharm• Always keep your pistol clean and in goodworking order.• Clean the pistol after 250 rounds, beforeevery ammunition type change and afterevery use. The chamber in particular must bethoroughly cleaned.• Never change or repair parts of your pistolyourself.• Have your pistol checked once a year by aqualified gunsmith or armorer, as defects,wear and tear, corrosion etc. may not alwaysbe visible from the exterior.• For repair or service work, we recommendthat you return your pistol to SIGARMS Inc.• If you order replacement parts withoutreturning the pistol, you are responsible forordering the correct replacement part and itsinstallation by a qualified gunsmith orarmorer.SIGARMS Inc. cannot be held liable for pistolfaults or malfunctions if the pistol has beenmodified or parts have been installed orrepaired by third parties.10.1 Fault detection, fault removalFaults can be prevented with the propermaintenance of the pistol (cleaning andinspection). Should, however, a malfunction occurwhile firing, proceed as follows:WARNING!Uncontrolled shot dischargePossibly death or serious injuries• Keep the pistol pointed in a safe firingdirection and remove your finger from thetrigger while you carry out the steps shownbelow.1. Remove the magazine.2. Retract the slide fully and lock to the rear(open) using the slide catch lever.3. Check (visually and manually with appropriateaid) to ensure there is no round, bullet, case orforeign bodies in the chamber or in the barrelbore. If a bullet is lodged in the barrel bore,strip the pistol and have the bullet removed bya qualified gunsmith using the proper tools.4. Remove all ammunition & foreign matter.Clean, lubricate and assemble pistol.5. Have pistol checked by a gunsmith or armorer.21 US 06.01
ServicingPart/fault Possible cause of fault/defect Possible fault/defect removalAmmunition feeding:Failure to feed.Failure to chamber.Slide:Slide does not close properly.Case ejection:Empty case remains in thechamber or gets stuck in ejectorport.Misfiring:Hammer hits; no discharge.Magazine is not insertedcorrectly, deformed or dirty.Pistol or rounds dirty or greasedtoo much.Large (heavy) slide springinstalled and standardammunition used.Pistol defective.Pistol or rounds dirty or greasedtoo much.Pistol defective.Underloaded ammunition.Recoil not sufficient due to dirt.Pistol defective.Firing pin sticks in thefiring pin guide.Ammunition fault.Pistol defective.Insert magazine correctly orreplace it.Strip, clean and lubricate pistol,clean or replace ammunition.Small (light) slide springmounted.Repair by manufacturer.Strip, clean and lubricate pistol,clean or replace ammunition.Repair by manufacturer.Replace ammunition.Strip, clean and lubricate pistol.Repair by manufacturer.Strip, clean and lubricate pistol.Have pistol checked by armorer.Manually cycle slide to load newroundRepair by manufacturer.06.01US22
Page 1 and 2: WARNING!Please read and understand
Page 3 and 4: General instructions1 General instr
Page 5 and 6: Safety regulations2.1 Safety indica
Page 7 and 8: Product description3 Product descri
Page 9 and 10: Safety mechanismsHandling2. Remove
Page 11 and 12: Handling6.4 Loading the pistol (rea
Page 13 and 14: Handling6.6 Reloading during firing
Page 15 and 16: Sight6. Place the screw 58 in the f
Page 17 and 18: Maintenance8. Remove slide assembly
Page 19: Maintenance9.4 Functional checkNote
Page 23 and 24: Scope of supplyAccessories11 Scope
Page 25 and 26: List of replacement partsFig. 20, S

WARNING! Please read and understand this owner's ... - Sig Sauer

Create successful ePaper yourself

Delete template?

Save as template?