Beta Manual 19025(1)

More documents

Recommendations

Info

INSTALLATION AND WIRINGDIST. AUTORIZADO®MEX (55) 53 63 23 31QRO (442) 1 95 72 60MTY (81) 83 54 10 18ventas@industrialmagza.comBE SURE TO READ ALL THE FOLLOWING INSTALLATION AND WIRING INSTRUCTIONSBEFORE INSTALLING THE CONTROLLER.1. Unpack the controller.2. Remove the controller front cover (if applicable) and check components in the controller. Reportshipping damage to the carrier.Figure 2. Series Beta Mounting Configurations3. The controller can be mounted in any of four configurations, as shown in Figure 2.4. Conduit entry is made by driving a 5/8” diameter pipe nipple, socket or similar rigid objectthrough the conduit opening. On all models install a 3/4” x 14 conduit fitting or pipe.NOTE: DO NOT USE A PUNCH SINCE THIS WILL LEAVE SHARP PROTRUSIONS AROUNDTHE OPENING. To prevent component damage from knockout fragments, apply masking tape tothe inside of the knockout before removing it.5. Remove the proper calibration wire(s) from the controller main board with a wire cutter, as shownin Table 6 and Figure 3.6. Be sure the main board is connected for the correct voltage. Figure 3 shows the main board connectedfor 230 volt operation. For 115 volt operation, the yellow and white leads on TransformerT1 connect to the 115V tabs, and the feedback jumper connects to the 90V ARM tab.NOTE: Model RB1 Controllers are designed for 115 volt operation only.7. Replace the front cover (if applicable) on the chassis.8. Mount the controller. If the controller is subjected to vibrations, it must be shock mounted.NOTE: Never mount the controller immediately beside or above the heat-generating equipment,or directly below water or steam pipes. If the controller is mounted in an enclosure, be sure thetemperature in the enclosure does not exceed 550.9. Prepare for wiring by removing the front cover (if applicable) and attaching it to the chassis asshown in Figure 4.8 Doc. No. 19025 • Boston Gear ® Ratiotrol ® DC Motor Speed Control
INSTALLATION AND WIRING (Con’t)DIST. AUTORIZADO®MEX (55) 53 63 23 31QRO (442) 1 95 72 60MTY (81) 83 54 10 18ventas@industrialmagza.comMotor Horsepower90 VDC 180 VDCRemove Wires1/12 1/6 R9 Thru R141/8 1/4 R9 Thru R141/6 1/3 R9 Thru R141/4 1/2 R10 Thru R141/3 3/4 R10 Thru R141/2 1 R11 Thru R143/4 1 1/2 R13 Thru R141 2 NoneTable 6. Series Calibration WiresCalibrationWiresT1YellowR8R9R10R11R12R13R14Figure 3. Main Board ConnectionsYellow115 V TabsTB1 A+ A- F- F+ L1 L2Fdbk JumperOn 180V ArmFdbk TabWhiteYellow230V180V 90VWhiteT1 Leads On230 V Tabs90V ArmFdbk TabDoc. No. 19025 • Boston Gear ® Ratiotrol ® DC Motor Speed Control 9
Page 1 and 2: DIST. AUTORIZADO®MEX (55) 53 63 23
Page 3 and 4: TABLE OF CONTENTSDIST. AUTORIZADO®
Page 5 and 6: OPERATOR CONTROLSTable 2. Operator
Page 7: PERFORMANCE CHARACTERISTICS (Con’
Page 11 and 12: INSTALLATION AND WIRING (Con’t)DI
Page 13 and 14: DIST. AUTORIZADOMODELS RB1, RB1B, R
Page 15 and 16: HALF VOLTAGE OUTPUTDIST. AUTORIZADO
Page 17 and 18: LIMIT SWITCH REVERSING (Con’t)DIS
Page 19 and 20: TORQUE CONTROL (Con’t)DIST. AUTOR
Page 21 and 22: TACHOMETER FEEDBACK (Con’t)DIST.
Page 23 and 24: Table 10. TroubleshootingDIST. AUTO
Page 25 and 26: RunStop56ToReversing Bd(Optional)57
Page 27 and 28: +12V R18.2K, 1/2WC21025VD112VIN4742

Beta Manual 19025(1)

Create successful ePaper yourself

Delete template?

Save as template?