Sikament 163N 20071710 Eng Rev 02 - Ä°zonet

Product DataFormAppearance / ColorsPackagingBrown homogenous liquid30 kg pails200 kg drumsTanktrucks possible on requestStorageStorage Conditions /Shelf Life24 months from date of production if stored properly in original and unopenedpackaging (drums, containers) at temperatures between +5°C and 35 °C protectfrom direct sunlight.Technical DataChemical BaseNaphthalene formaldehyde sulphonate polymer based liquidDensity 1.16 – 1.22 kg/l, at 20°CpH Value 6-10Freezing pointTotal Chloride IonContentEffect of Overdosing-4°CMax. % 0.1, chloride-free (TS EN 934-2)Dosages above the recommended limits may cause retarding. During this periodthe concrete must be kept moist in order to prevent premature drying out.SystemInformationApplication DetailsConsumption / Dosage Recommended dosage rate is between 0.8 % and 2.5 % by weight of binder (800–2500 g for 100 kg binder). Exact dosage rates are dependent on quality of binderand aggregate, Water/Binder ratio and ambient temperature. Therefore, it isadvisable to carry out trial mixes to establish the exact dosage rate required.ApplicationConditions/LimitationsCompatibilitySikament ® -163N may be combined with the following Sika products among others-Sika ® Aer-SikaPump ®-SikaRapid ®-SikaFume ® HR-Sika ® Ferrogard ® -901-Plastocrete ® N-SikaFibre ®-Sika ® AntifreezeTrails are recommended before combining products2 2/3Sikament® -163N

ApplicationInstructionsDispensingApplication Method /ToolsCleaning of ToolsSikament ® -163N is added to the gauging water at the plant or added on site intothe concrete mixer. When added separately to the freshly mixed concrete, furthermixing should take place for at least 3 minutes. Before being discharged, theconcrete must be visually inspected for even consistency. Admixture dosage mustbe suitable in order to prevent segregation.The standard rules of good concreting practice, concerning production as well asplacing, are to be followed. Refer to relevant standards. Fresh concrete must becured properly.Clean all tools and application equipment with water immediately after use.Hardened / cured material can only be mechanically removed.ConstructionNotes on Application /LimitationsNotes• When using Sikament ® -163N, a suitable mix design has been taken intoaccount and local material sources should be trialled.• Sikament ® -163N should not be added to dry cement.• Sikament ® -163N should be added with the mixing water or introduced at theend of the mixing process.Before application, suitability tests must be performed.All technical data stated in this Product Data Sheet are based on laboratory tests.Actual measured data may vary due to circumstances beyond our controlLocal Restrictions Please note that as a result of specific local regulations the performance of thisproduct may vary from country to country. Please consult the local Product DataSheet for the exact description of the application fields.Health and SafetyInformationLegal NotesFor information and advice on the safe handling, storage and disposal of chemicalproducts, users shall refer to the most recent Material Safety Data Sheet containingphysical, ecological, toxicological and other safety-related data.The information, and, in particular, the recommendations relating to the applicationand end-use of Sika ® products, are given in good faith based on Sika's currentknowledge and experience of the products when properly stored, handled andapplied under normal conditions in accordance with Sika’s recommendations. Inpractice, the differences in materials, substrates and actual site conditions are suchthat no warranty in respect of merchantability or of fitness for a particular purpose,nor any liability arising out of any legal relationship whatsoever, can be inferredeither from this information, or from any written recommendations, or from any otheradvice offered. The user of the product must test the product’s suitability for theintended application and purpose. Sika reserves the right to change the propertiesof its products. The proprietary rights of third parties must be observed. All ordersare accepted subject to our current terms of sale and delivery. Users should alwaysrefer to the most recent issue of the local Product Data Sheet for the productconcerned, copies of which will be supplied on request.Sika Yapı Kimyasalları A.Ş.Deri Org. San. Böl. 2. Yol J–7Parsel, Aydınlı, Orhanlı Mevkii,34957 Tuzla, İstanbul, TürkiyeÇağrı MerkeziTelefonFaksbilgi@tr.sika.com+90 216 444 74 52+90 216 581 06 00+90 216 581 06 99www.sika.com.tr3 3/3Sikament® -163N