Datatrac 400 Operations Manual - Aeroflex

More documents

Recommendations

Info

Aeroflex Operation ManualA portion of the help menu listing of all currently defined equipment ID codes that are supported bythe DATATRAC 400 appears below. The full listing is contained in Appendix D. The user may scrollthrough the list one line at a time using the up and down arrows. The F (forward) and B (back) keysmove the list 10 lines at a time and may be used to scroll more rapidly. It may be more convenient forthe operator to have the list organized alphabetically rather than numerically. This may beaccomplished by pressing A as noted in the help screen header message.* HELP SCREEN * Equipment ID Codes *Press ^,v,B,F to scroll list,A for alphabetic order, 0 for numericPress ENT to return to setup screen001 Flight Control Computer002 Flight Management Computer003 Thrust Control Computer004 Inertial Reference System005 Attitude and Heading Ref System006 Air Data System007 Radio Altimeter008 Airborne Weather Radar009 Airborne DME00A FAC (A310)00B Global Positioning System00D AIDS Data Management Unit010 Airborne ILS Receiver3.1.6 LABEL DATA DEFINITIONSSince the user may not always be familiar with label assignments for parameters he is viewing, a helpmenu gives label data definitions based on equipment ID. This menu is accessed from the Receive,Transmit, Record or break data review screens by pressing the D key. The following example showsthe label definitions for equipment ID 004.Label Definitions * Equipment ID = 004Inertial Reference SystemLbl Parameter Definition010 Present Position-Latitude011 Present Position-Longitude012 Ground Speed013 Track Angle-True014 Magnetic Heading015 Wind Speed016 Wind Direction-True041 Set Latitude042 Set Longitude043 Set Magnetic Heading044 True HeadingPress ^,v.F,B to scroll, ENT to returnDATATRAC 400 – REV 0 – PAGE 3-6
Aeroflex Operation Manual3.2 DEFAULT RECEIVER SETUP OPTIONSIf the D key is pressed on the primary receiver setup menu, the following menu will appear, allowingthe user to edit additional defaults of the receive mode. (Note: pressing D at the equipment ID fieldwill be interpreted as a data entry.) These receive parameters are listed in a separate screen sincethey typically will be left in their default settings.* RECEIVER SETUP *Channel 1 Default SettingsData Format : ENG Display Lines : 14Interval : INST Bus Monitor : 4Rcv Download : NONE> To step through options< To see HELP screen for each line^ v To move to next/previous linePress ENT to return to main setup menuDATATRAC 400 – REV 0 – PAGE 3-7
Page 1: OPERATION MANUALDATATRAC 400ARINC 4
Page 5 and 6: Caution, hot surface. Danger - high
Page 7 and 8: ELECTROSTATIC DISCHARGE GENERAL WAR
Page 10 and 11: Aeroflex Operation ManualSECTION IV
Page 12 and 13: 1.0 INTRODUCTION TO THE DATATRAC 40
Page 14 and 15: Aeroflex Operation ManualDATATRAC 4
Page 20 and 21: Aeroflex Operation Manual** DATATRA
Page 22 and 23: Aeroflex Operation ManualTo change
Page 24 and 25: Aeroflex Operation Manual3.1.4 RECE
Page 28 and 29: Aeroflex Operation ManualThe follow
Page 30 and 31: Aeroflex Operation ManualIn the BIN
Page 32 and 33: Aeroflex Operation ManualDiscretes
Page 34 and 35: Aeroflex Operation Manual3.2.1.2 RE
Page 36 and 37: Aeroflex Operation ManualWhen two p
Page 38 and 39: Aeroflex Operation ManualThere are
Page 40 and 41: Aeroflex Operation ManualAs an exam
Page 42 and 43: Aeroflex Operation Manual- - - - -
Page 44 and 45: Aeroflex Operation Manual3.3.2 REAL
Page 46 and 47: Aeroflex Operation Manual4.0 TRANSM
Page 48 and 49: Aeroflex Operation Manual4.1.3 TRAN
Page 50 and 51: Aeroflex Operation ManualThe follow
Page 54 and 55: Aeroflex Operation ManualSection 3.
Page 58 and 59: Aeroflex Operation Manual4.3.4 SAMP
Page 60 and 61: Aeroflex Operation Manual4.3.5 BURS
Page 62 and 63: Aeroflex Operation ManualThe frame
Page 64 and 65: Aeroflex Operation ManualEXAMPLE OF
Page 66 and 67: Aeroflex Operation ManualEquipment
Page 68 and 69: Aeroflex Operation ManualThe table
Page 70 and 71: Aeroflex Operation Manual5.1.2 CHAN
Page 72 and 73: Aeroflex Operation Manual- - - - -
Page 74 and 75: Aeroflex Operation Manual5.5.2.2 TI
Page 76 and 77:
Aeroflex Operation ManualDAC 2 may
Page 78 and 79:
Aeroflex Operation ManualSECTION VI
Page 80 and 81:
Aeroflex Operation Manual* BREAK MO
Page 82 and 83:
Aeroflex Operation ManualWhen the b
Page 84 and 85:
Aeroflex Operation ManualUP - The u
Page 86 and 87:
Aeroflex Operation ManualJust prior
Page 88 and 89:
Aeroflex Operation ManualThe choice
Page 90 and 91:
Aeroflex Operation ManualCMD: * * *
Page 92 and 93:
Aeroflex Operation ManualAn example
Page 94 and 95:
Aeroflex Operation ManualA typical
Page 96 and 97:
Aeroflex Operation Manual7.3.2 SHOP
Page 98 and 99:
Aeroflex Operation ManualTransmissi
Page 100 and 101:
Aeroflex Operation ManualPressing t
Page 102 and 103:
Aeroflex Operation ManualAPPENDIX A
Page 104 and 105:
Aeroflex Operation ManualThe progra
Page 106 and 107:
Aeroflex Operation ManualThe record
Page 108 and 109:
Aeroflex Operation ManualAPPENDIX B
Page 110 and 111:
Aeroflex Operation ManualRecord Ope
Page 112 and 113:
Aeroflex Operation ManualDESCRIPTIO
Page 114 and 115:
Aeroflex Operation ManualIMPLEMENTA
Page 116 and 117:
Aeroflex Operation ManualAVM DataEq
Page 118 and 119:
Aeroflex Operation ManualDataBit 28
Page 120 and 121:
Aeroflex Operation ManualFault Code
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Aeroflex Operation ManualEICSA Data
Page 130 and 131:
Aeroflex Operation ManualLABEL SDI
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Bit Encoding for WeightBit = 3 bit
Page 138 and 139:
Aeroflex Operation ManualFQIS DataE
Page 140 and 141:
Aeroflex Operation ManualSSMBit 31
Page 142 and 143:
Aeroflex Operation ManualFSEU DataE
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Aeroflex Operation ManualAPPENDIX E
Page 168 and 169:
Aeroflex Operation ManualTABLE E-2S
Page 170 and 171:
Aeroflex Operation ManualPRIMARY SE
Page 172 and 173:
Aeroflex Operation ManualAPPENDIX F
Page 174 and 175:
Aeroflex Operation Manual4.5.3. CHA
Page 176 and 177:
Aeroflex Operation Manual1. INTRODU
Page 178 and 179:
2. SETUP MENU SELECTIONS.Aeroflex O
Page 180 and 181:
Aeroflex Operation ManualAcquisitio
Page 182 and 183:
Aeroflex Operation ManualFILE TRANS
Page 184 and 185:
Aeroflex Operation Manual4. DEFININ
Page 186 and 187:
Aeroflex Operation ManualHEX: Lk SA
Page 188 and 189:
Aeroflex Operation ManualS (Standby
Page 190 and 191:
Aeroflex Operation ManualTIP: There
Page 192 and 193:
Aeroflex Operation ManualLk SAL Typ
Page 194 and 195:
Aeroflex Operation Manual4.5.11. TE
Page 196 and 197:
Aeroflex Operation ManualEach time
Page 198 and 199:
Aeroflex Operation ManualAll variab
Page 200 and 201:
Aeroflex Operation ManualThe select
Page 202 and 203:
6.4. Display of Non-SAL Words.Aerof
Page 204 and 205:
Aeroflex Operation ManualThe RS-232
Page 206 and 207:
Aeroflex Operation ManualInitial He
Page 208:
7.2. Real-Time Data DownloadAerofle
show all

Datatrac 400 Operations Manual - Aeroflex

Create successful ePaper yourself

Delete template?

Save as template?