Lab Equipment - Cole-Parmer

High-quality, variable-speed mixers featuringfull-range performanceStir-Pak ® General-Purpose Mixerl Keyless chuckl LED indicatorOur general-purpose mixer is idealfor routine, light-duty mixing of water-likeviscosities only delivering 4000 rpm.Speed ramps to set speed. The brushedDC motor has a compact speedcontroller integrated by a customanodized aluminum potentiometercontrols both on/off and variablespeedsettings for single directionmixing.Mixer includes: 3 ⁄8" (9.5 mm) diameterx 12" (305 mm) L 316SS shaft,1 1 ⁄2" (38 mm) diameter propeller,6" (152 mm) mounting rod, 6' (1.8 m)grounded cord with power supply.Complete system adds: doubleclamp and support stand.Complete general-purposemixing system 04555-50General-purposemixer 04555-00Super $avings!Save time and money when youbuy a complete system ratherthan individual components.MixersLab EquipmentStir-Pak ® Dual-Shaft Mixerl Use for either high-speedor high-torque mixingl Solid-state—gives youprecise control of speedTwo motor shafts give you twomixers in one. The direct-driveshaft provides high-speed,low-viscosity mixing; switchto the gear-reduction shaft foryour low-speed, high-viscositymixing needs.Rugged, permanentmagnet,totally enclosednonventilated (TENV) motorhas permanently lubricatedball bearings. Gear-shaftgear ratio is 20:1.Our solid-state controllermaintains speed regulationbetter than ±2%—criticalfor materials that changeviscosity as mixingprogresses. Improvedtorque limiting featureprotects against motor gearfailure. Controller is totallyenclosed and has an IP53rating for protection againstdust and water; it isUL-listed and CSA-approved.A 6-ft (1.8‐m) cord connectsthe controller and the motor.Mixer includes: 6"L x 1 ⁄2" dia(152 mm L x 13 mm dia)mounting rod; chuck (acceptsshafts from 5 ⁄16" to 3 ⁄8" [8 to 10mm] dia); and 6-ft (1.8-m),3-wire cord with plug.Complete system adds: 3 ⁄8" diax 12"L (10 mm dia x 305 mm L),316 SS shaft; 3" dia (76 mm dia)propeller; 316 SS, double clamp;and support stand.Note: Order transformer belowfor 230 VAC operation.MixersDual-shaftmixer04555-25(gear shaftshown inuse)Completedual-shaftmixing system04555-60CatalogDescriptionnumberGeneral-purpose mixerZG-04555-00MixerZG-04555-50 Complete systemDual-shaft mixerAccessoriesZG-04552-00 Shaft, 3 ⁄8" dia x 24"L (10 mmdia x 610 mm L); 316 SS. Accepts a 5 ⁄16"(8 mm) bore dia propellerZG-04552-60 Propeller, 3" (76 mm) overalldia x 5 ⁄16" (8 mm) bore dia; 316 SSZG-04552-55 Propeller, 2" (51 mm) overalldia x 3 ⁄8" (9.5 mm) bore dia; 316 SSSpeed(rpm)WattsMax torquein-oz (N . m)0 to 4000 15 9.5 (0.067)ZG-01578-05 Transformerfor 230 VAC operationZG-04552-80 Mixer support stand has acorrosion resistant base and 303 SS supportrod. Rod measures 29"H x 5 ⁄8" dia (740 mmH x 16 mm dia). Both legs accept an extrasupport rod (sold separately online)Dimensions(W x H x D)83 x 133 x 165 mm(3.267" x 5.25" x 6.5")Shaft dia,(mm)*5⁄6" to 3 ⁄8"(8 to 10)ZG-04555-25 Mixer Direct-drive shaft: 50 to 5000Direct-drive shaft: 0.028 (4) Motor: 146 x 89 L x dia 5⁄6" to74.93 ⁄8"ZG-04555-60 Complete system Gear shaft: 3 to 250 Gear-shaft: 0.564 (80) Controller: 178 x 86 x 124 (8 to 10)† Order transformer 01578-05 for 230 VAC operation.* Note: Shaft has one end turned down to 5 ⁄6" to accommodate 5 ⁄16" bore properller .Power(VAC, Hz)115/230, 50115, 50/60 †ZG-08041-22 Double clamp for mountingthe mixer head onto a stand; holdsrods up to 7 ⁄8" dia (22 mm dia)ZG-04552-75 Support platform formounting controller adjacent to mixerhead (for mixer 04555-60)U.S. Toll-free: 800-323-4340 • Outside the U.S.: 847-549-7600 • www.coleparmer.comCanada 800-363-5900 • India 91-22-6716-2222 • UK 0500-345-300PriceLaboratory Equipment & Supplies Page 27