Operating and installation instructions WAREMA Mobile System ...

More documents

Recommendations

Info

Setting the wind speed limit(specialist dealers only)For an awning to be protected properly, the limit valueabove which a wind alarm is triggered needs to be set forthat particular awning (type, width, projection, etc.).The wind speed limit is already set to the correct valuein awnings that are delivered with the WMS.C CAUTIONever change the wind speed limit set byyour specialist dealer. An incorrect limitvalue may lead to awning damage in windyweather.Wind speed limit× 0 Wind monitoring off!1 Most sensitive setting2345 Factory setting6789 Least sensitive settingButton/Action/resultdisplayThe wind speed limit can only be changed if the WMSplug receiver was first learned into the hand-held transmitter.Using the awning button, select the channelthat you wish to set.The LED below the channel number lightsE.g.upPress the mode button with a pointedobject until lights up and mode 0 isselected.N NOTE The mode button must be pressedbefore the hand-held transmitterreturns to sleep mode.If you release the mode button tooearly or press it for too long and ahigher mode is displayed:Release the button and press andhold it again; the process restartsat 0.+ and the LED above the 0 lights up inred.Briefly press the learn button to activatethe mode.The LED above the number 0 lights upbriefly in green.The sun control is displayed automatically.Press the info button repeatedly until thesymbol for the wind control lights up.The LED below the control symbol showsthe state of the control system.GREEN: ActiveRED: InactiveE.g. The parameter value of the wind control is... displayed in the upper row of LEDs (here,E.g....limit value 2).RED:Value 0; the control function isoffGREEN: Values 1 to 9FLASHES: Multiple receivers with differentvalues in the channel. The valueof the first receiver is displayed.Use the arrow keys ( + light up) tochange the parameter value.The upper row of LEDs shows how thevalue changes (new value = 1)Press thebuttonThe transmission LED lights up for 2secondsGREEN: The parameter value was storedin all receivers of the channelRED: Not all receivers could bereached; press the buttonagain.Leave the dealer mode with the mode button( is no longer lit)4We reserve the right to carry out improvements890376_d•en•22.10.2013
Maintenance and cleaningStorageIf you will not be using the awning for an extended period(e.g. over the winter, during which negative temperatureswill shorten the battery life), take the WMS Wind sensor offthe mounting plate. Store the wind sensor in an enclosedarea and remove the batteries during this time.Replacing the batteriesCheck the battery charge status at least once a year.Replace the batteries if the red LED lights up after pressingthe battery button. If the batteries are depleted, theawning is automatically retracted or is stopped afterseveral seconds if it is being extended to protect againstwind damage.Press the battery button for approx. 5 seconds untilthe red LED lights up continuously and then take thewind sensor off the mounting plate.To replace the batteries (type AAA, IEC LR03, "Micro"),remove the four screws on back of the housing. Openthe battery compartment (Fig. 3) and insert the newbatteries. Ensure the correct polarity: The plus (+) andminus (-) poles of the batteries must agree with themarks in the battery compartment.Only use new batteries of the same type and alwaysreplace both batteries. Use high quality batteries -inexpensive batteries can leak and damage the device.If the device is not used for a longer period, please removethe batteries. Do not use rechargeable batteries.Clip the wind sensor back onto the mounting plateand press any button on the wind sensor to end the"Replace battery" mode.CleaningClean the enclosure with a soft, damp cloth. Do not usedetergents or cleaners, abrasive substances or steamcleaners.LiabilityFailure to comply with the product information in theseinstructions and use of the unit in a manner that contravenesits intended use and purpose may result in themanufacture refusing to honour warranty claims for productdamage. In this case, liability for consequential harmto persons or damage to property will also be excluded.Follow the instructions in the operating instructions of yoursun shading system. Liability is also excluded for damageto the sun shading system resulting from operation undericy conditions.Technical dataWCATEMA Mobile SystemWMS Wind sensorMin. Typ. Max. UnitSupplyBattery type2 x AAA (IEC LR03, "Micro")Supply voltage 2.4 3.0 3.2 V DCRF transmitterTransmission frequency 2.40 2.48 GHzTransmission power 0 dBmReception sensitivity -95 dBmRange30 m(environment without interference)TEnclosureDimensions (L×W×H in mm) 71 × 40 × 27Degree of protectionIP65Safety classIIIMiscellaneousTest standards DIN EN 60950-1:2003-03DIN EN 61000-6-2:2006-03DIN EN 61000-6-3:2005-06(Corr.2005-11)DIN EN 300328 V1.7.1.(2006-10)Automatic operation Type 1Software classALocation of useClean ambient conditionsConformityViewable under www.warema.deAmbient conditionsOperating temperature -20 20 60 °CStorage temperature -25 70 °CRel. humidity10 40 85 %RH(non-condensing)Article numbersWMS Wind sensor 1002 772WAREMA Renkhoff SEHans-Wilhelm-Renkhoff-Strasse 2D-97828 MarktheidenfeldDisposalAfter use, the device and the batteries must be disposedof according to legal regulations or brought to your localrecycling centre.890376_d•en•22.10.2013We reserve the right to carry out improvements5
Page 1 and 2: Operating and installation instruct
Page 3: Operating the awning with a hand-he
Page 7 and 8: Awning typesMounting materialsAWSB5

Operating and installation instructions WAREMA Mobile System ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?