OmniScan® iX - Tecsud

OmniScan ® iX SpecificationsBenchtop versionRack-mount versionWeightDisplayOverall dimensions (W × H × D)375 mm × 238 mm × 185 mm (14.75 in. × 9.4 in. × 7.3 in.)485 mm × 222 mm × 190 mm (19 in. × 8.7 in. × 7.5 in.)6.5 kg (14.3 lb)800 × 600 10.4 in. TFT color LCDConnectors BNC (2, 4, or 8)Pulser/ReceiverNumber of pulsers/receivers 2, 4, or 8PulserPulse output 50 V, 100 V, 200 V, 300 V ±10%Pulse widthFall timePulse shapeOutput impedanceReceiver gain rangeAdjustable from 30 ns to 1000 ns ±10%, resolution of 2.5 nsLess than 7 nsNegative square waveLess than 7 ΩReceiver0–100 dB, by steps of 0.1 dBMaximum input signal 20 V p-p (screen at 128%)Minimum sensibility 200 µV p-p (screen at 128%)Noise referred to input 160 µV p-p (26 µV RMS) (128%)Input impedanceInput filter(100% bandwidth)Bandwidth of the systemRectifierModeSmoothing50 ΩNumber of points 16TCG rangeMaximum gain slopeA-scan acquisition rateMaximum pulsing rateCentered at 1 MHz (1.5 MHz), centered at 2 MHz (2.25 MHz), centeredat 5 MHz (4 MHz), centered at 10 MHz (12 MHz), centered at 15 MHz,centered at 20 MHz, 0.25–2.5 MHz, 2–25 MHz BB0.25–35 MHz (–3 dB)Positive, negative, full unrectifiedPE (pulse-echo), PC (pitch-and-catch), TT (through-transmission).In PC mode, the maximum number of pulsers equals the number ofchannels divided by 2.DigitalUp to 40 dB20 dB/µsReal-time averaging 2, 4, 8, 16QuantitySynchronizationA-scan recording (TOFD)TCGData acquisition6000 A-scans/s(PRF/N, where N = number of channels) (512-point A-scan)12 kHz (C-scan + Alarm mode). Up to 6 kHz with full A-scan recordingData processingGates3: I (synchro), A and B (measure)I, A, B referenced on main bang, B referenced on gate I or A (postsynchronization)Data storage6000 A-scans/s (512-point A-scan) (3 MB/s transfer rate)C-scan type data recording12,000 (A1, A2, A3, T1, T2, T3) (3 gates); 12 kHz (lower frequency forcorrosion mapping)Storage Internal 8 GB Microdrive ®Refresh rateModesOn timeOn encoderNumber of alarmsConditionsSignalAnalog outputs (at full PRF)Digital inputsData visualization60 HzA-scan, B-scan, C-scan, strip charts, multiple A-scans, and TOFDData synchronization1 Hz–12 kHzOn 1 or 2 axes divided by 1 to 65,536 stepsOutputs and inputs16 (programmable, hold time and delay, filters for n occurrences)Any logical combination of gatesAmplitude or time of flight of gate A or B16 (0 V to +5 V) (programmable for each gate)4 programmable DINOmniScan iX OptionsHardware OptionsOMNI-IX-A-RACK1: OmniScan iX rackmountbracket optionThe OmniScan i X is also available as a 19-in., 5U rack-mountversion for easier integration into production environments.OMNI-IX-A-ACC1: OmniScan iX accessorykit includes the following:• 1 external keyboard,• 1 optical mouse,• 1 storage USB keyOMNI-IX-A-SWIV: OmniScan iX swivelarmassemblyOMNI-IX-A-SCASE: OmniScan iX hardcarrying caseSoftware OptionsOMNI-IX-SO-ENC1: OmniScan iX softwareoption to activate two encoderinputs on the instrumentOMNI-IX-SO-BEA*: OmniScan iX softwareoption to activate back wall echoattenuator on the instrument(available the end of 2006) Standard Inclusions• OmniScan iX instrument• Ethernet ® cable• OmniScan software• Users User’s manual• NDT Remote Control SoftwareLibrary 2.0OmniScan_iX_EN_0609 • Printed in Canada • Copyright © 2005–2006 by Olympus NDT. All Rights Reserved.All specifications are subject to change without notice.Olympus and the Olympus logo are registered trademarks of Olympus Corporation.R/D Tech, the R/D Tech logo, OmniScan, and the OmniScan logo are registered trademarks, and “Innovation in NDT” and TomoView are trademarksof Olympus NDT Corporation in Canada, the United States, and/or other countries.Other company or product names mentioned in this document may be trademarks or registered trademarks of their respective owners.Olympus NDT505, boul. du Parc-TechnologiqueQuébec (Québec) G1P 4S9Canadardtech@olympusndt.comwww.olympusNDT.com