SPEEFLO Admiral - Paint Sprayers, HVLP Sprayers, Powered Rollers

More documents

Recommendations

Info

<strong>Admiral</strong> 155-559 Fluid Pump AssemblyItemNo.PartNo.DescriptionQTY.1 431-007 Nut, coupling *42 155-907 Block, pump 13 155-053 Packing set, Poly/Lthr. 2195114 155-906 Upper packing spring 15 155-010 Washer 11816126 155-982 Rod, displacement 17 155-009 Washer, piston 18 155-001 Lower packing spring 19 155-225 Ball, S.S. 110 155-921 Piston seat assembly 1202781111 891-373 O-ring 212 155-932 Cylinder 113 174-113 Stop, ball 114 174-102 Cage, ball 115 178-700 Ball, S.S. 11316 155-991 Valve, foot 1321223910141516142-102 Assembly SetItemNo.PartNo.DescriptionQTY.18 140-016 Stanchion 219 441-956 Rod, connecting 120 868-101 Nut 121 870-004 Washer 622 870-401 Nut 2DisplacementRodStroke Length Displacement Volume /StrokeDisplacement Volume / 40 Cycles/ 80 StrokesIN 2 CM 2 IN CM IN 3 CM 3 LITER IN 3 GAL. CM 3 LITER.976 6.3 4 10.2 3.9 63.9 .0639 312 1.35 5113 5.113MotorSelectionMotor Pumpratio850 Series 60:118 © Titan Tool Inc. All rights reserved.
155-559 Fluid Pump Service Informationimportant: Use of non-Titan manufactured service partsmay void warranty.The 155 Series Pump should receive a routine servicing afterapproximately 1000 hours of use or earlier if there is excessiveleakage from the top packing, or if pump strokes become fasteron one stroke or another. The use of Titan Lubrisolv Part #310-200 is recommended as an upper packing lubricant. donot substitute oil, water or solvent for an upper packinglubricant.Disassembly Procedure1. Remove siphon hose assembly.2. If the pump is connected to air motor, hold motor pistonrod at wrench flats and unthread coupling nut (1) toseparate pump from motor.3. Unthread and remove foot valve (16) and pump cylinder(12) to separate from pump block (2) and remove ball (15),ball stop (13), ball cage (14) and O-ring (11).4. Secure piston seat assembly (10) in a vise and unthreaddisplacement rod (6) to remove packing set (3), spring (8)and washer (7).5. Inspect and clean all parts. Reject cylinder (12) and/ordisplacement rod (6) if hard chrome is grooved or wornthrough to gray metal.Reassembly ProcedureService KitsItemNo.PartNo.Pump service kits, minorDescription155-0513 155-052 Packing set, leather 2155-0553a 155-053 Packing set, Leather/Poly 29 155-225 Ball, S.S. 1 111 891-373 O-ing 2 215 178-700 Ball, S.S. 1 1ItemNo.426-051 Loctite sealant 1 1PartNo.Pump service kits, majorDescription155-051155-051 Minor service kit 1155-055155-055 Minor service kit 16 155-981 Rod, displacement 1 112 155-932 Cylinder 1 1NOTE: If cylinder (12) and displacement rod (6) arereusable, then only a minor kit part # 155-051 or155-055 may be required for reassembly.1. Place new packing set (3) over piston seat (10) with “V”packings point downward (V) and reassemble with ball(9), spring (8),washer (7) and displacement rod (6) in thatorder. Tighten and use Loctite on clean threads.2. Insert new upper packing set (3) into pump block (2).important: Peak of “V” packings must point upwards onreassembly.Install upper packing spring (4) and washer.3. Insert displacement rod assembly (6) through pump block(2) holding upper packing set (3) in place with fingers.4. Lubricate the threaded ends of cylinder (12) including theO-rings (11) to protect them on reassembly.5. Thread cylinder (12) into pump block (2). Do notovertigthen.6. Replace ball (15), ball cage (14) and ball stop (13) intofoot valve (16) and thread into cylinder (12). The O-rings(11) should be lubricated to protect it on replacement offoot valve. It is not necessary to overtighten as seal isobtained when parts are fully threaded together.NOTE: It is not necessary to overtighten foot valve andcylinder into pump block. O-ring seals performsealing function without excessive tightening.Full thread engagement is sufficient. The footvalve may be rotated back up to 1/2 turn from fullengagement for convenient hose position.NOTE: For siphon hose attachment, it is criticallyimportant that the threads of the siphon hose fitsnugly into the foot valve with the hose assemblycouplings Teflon taped and sealed to prevent airinlet leakage.© Titan Tool Inc. All rights reserved. 19
Page 1: Owner’s ManualFor professional us
Page 4 and 5: Table of ContentsSafety Precautions
Page 6 and 7: SetupThe flow from the spray tip is
Page 8 and 9: Operation1. Repeat above Startup pr
Page 10 and 11: Troubleshooting - Airless SprayingC
Page 12 and 13: Admiral Series Portable Models21385
Page 14 and 15: Admiral Series Wall Mount and Drum
Page 16 and 17: Admiral 850-555 and 850-557 Air Mot
Page 20 and 21: Admiral 181-556 Fluid Pump Assembly
Page 26 and 27: Admiral 928-835 Air Assembly3421516
Page 28 and 29: Admiral Pump Mount Drum Cover111 23
Page 30 and 31: Admiral Outlet Accessories - 920 Ou
Page 32 and 33: Admiral Fluid Accessories - Siphon
Page 34 and 35: Admiral Outlet Accessories1 2 3 4 5
Page 36: Admiral Key Accessories and Service

SPEEFLO Admiral - Paint Sprayers, HVLP Sprayers, Powered Rollers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?