SPEEFLO Admiral - Paint Sprayers, HVLP Sprayers, Powered Rollers

More documents

Recommendations

Info

<strong>Admiral</strong> 181-556 Fluid Pump AssemblyItemNo.PartNo.DescriptionQTY.1 185-981 Pin, roll 123252 185-984 Rod, displacement 13 181-906 Block, pump 14 175-001 Upper packing set, Lthr. 1245 182-906 Spring, packing 16 228-002 Nipple, hex 1127 182-007 O-ring, Teflon 18 185-011 Retainer, spring 19 185-010 Spring, packing 12234510 180-002 Lower packing set, Lthr. 111 182-921 Seat, piston 112 182-932 Cylinder 113 174-113 Stop, ball 114 174-102 Cage, ball 115 178-700 Ball, S.S. 116 155-981 Valve, foot 121206717 742-223 O-ring, Buna 118 174-001 O-ring, Teflon 119 920-103 Ball 119181789101112131415142-101 Assembly SetItemNo.PartNo.DescriptionQTY.20 868-101 Nut 221 870-004 Washer 222 870-005 Washer, spacer 423 140-016 Stanchion 224 441-956 Rod, connecting 125 138-007 Nut, coupling ** Not included in this assembly16DisplacementRod AreaStroke Length Displacement Volume /StrokeDisplacement Volume / 40 Cycles/ 80 StrokesIN 2 CM 2 IN CM IN 3 CM 3 LITER IN 3 GAL. CM 3 LITER1.38 8.90 4 10.2 5.55 90.9 0.091 444 1.92 7272 7.27MotorSelectionMotor Pumpratio850 Series 40:120 © Titan Tool Inc. All rights reserved.
181-556 Fluid Pump Service Informationimportant: Use of non-Titan manufactured service partsmay void warranty.The 181 Series Pump should receive a routine servicing afterapproximately 1000 hours of use or earlier if there is excessiveleakage from the top packing, or if pump strokes become fasteron one stroke or another. The use of Titan Lubrisolv Part #310-200 is recommended as an upper packing lubricant. donot substitute oil, water or solvent for an upper packinglubricant.Disassembly Procedure1. Test pump before disassembly. Follow test procedure inTroubleshooting Guide - Fluid Section.2. Remove siphon hose assembly.3. Remove stanchion nuts (20) and washers (21).4. If the fluid section is connected to an air motor, hold the airmotor piston rod at the wrench flats and unthread couplingnut (25) to separate pump from motor.If the motor is connected to a hydraulic motor, removeallen set screw between the two flats on hydraulic motorrod. Hold the hydraulic motor rod at the wrench flatsand unthread coupling nut (25) to separate pump fromhydraulic motor.important: Never use a pipe wrench, pliers, etc. on thechrome part of hydraulic, air or fluid section rod.5. Remove roll pin (1) on connecting rod (24). Removeconnecting rod from displacement rod (2).6. Unthread and remove foot valve (16).7. Remove Teflon O-ring (18), Buna O-ring (17), ball stopring (13), ball cage (14) and ball (15).8. Remove cylinder (12).9. Remove displacement rod (2).10. Place piston seat (11) in a vise and use a wrench on theflats to remove the displacement rod (2) from the pistonseat (11).11. Remove lower packing set (10), spring (9), spring retainer(8) and ball (19).12. Remove upper packing spring (5), O-ring (7) and packingset (4) from pump block (3).13. Clean and inspect all parts. Inspect rod or pump tube’shard chrome for grooves, dents or worn areas. Replace ifhard chrome is damaged. Inspect valve seats and replaceif cracked or worn.8. Insert ball (15), ball cage (14), ball stop retainer ring (13),Buna O-ring (17) and Teflon O-ring (18) into foot valve.important: Lubricate all O-rings.9. Thread foot valve (16) back into cylinder (12).NOTE: It is not necessary to overtighten foot valve andcylinder into pump block. O-ring seals performsealing function without excessive tightening.Full thread engagement is sufficient. The footvalve (16) may be rotated back up to 3/4 turn fromfull engagement for convenient hose position.10. Insert coupling nut (25) back onto connecting rod (24) andthread connecting rod (24) back onto displacement rod(2).Service KitsItemNo.Pump service kit, minor (Part # 182-050)PartNo.DescriptionQTY.4 175-001 Packing set, leather 17 182-007 O-ring, Teflon 110 180-002 Packing set, leather 115 178-700 Ball 117 742-223 O-ring 118 174-001 O-ring, Teflon 119 920-103 Ball 1ItemNo.Pump service kit, major (Part # 182-520)PartNo.DescriptionQTY.182-050 Pump service kit, minor 12 185-984 Rod, displacement 111 182-921 Seat, piston 112 182-932 Cylinder 1Reassembly Procedure1. Insert upper packing set (4) into pump block (7)important: Peak of “V” packings must point upwards onreassembly.2. Insert upper spring (5); small end of spring must go towardthe packing set.3. Place packing set (10) over piston seat (11).important: Peak of “V” packings must point downwardon reassembly.4. Replace spring (9), spring retainer (8) and ball on pistonseat (11).5. Thread seat back onto displacement rod (2).important: Use Loctite on clean threads.6. Insert displacement rod (2) assembly through upperpacking set (4) in pump block (3).7. Place O-ring (7) on end of cylinder (12) and thread backinto pump block (3).important: Lubricate all O-rings before assembly.© Titan Tool Inc. All rights reserved. 21
Page 1: Owner’s ManualFor professional us
Page 4 and 5: Table of ContentsSafety Precautions
Page 6 and 7: SetupThe flow from the spray tip is
Page 8 and 9: Operation1. Repeat above Startup pr
Page 10 and 11: Troubleshooting - Airless SprayingC
Page 12 and 13: Admiral Series Portable Models21385
Page 14 and 15: Admiral Series Wall Mount and Drum
Page 16 and 17: Admiral 850-555 and 850-557 Air Mot
Page 18 and 19: Admiral 155-559 Fluid Pump Assembly
Page 26 and 27: Admiral 928-835 Air Assembly3421516
Page 28 and 29: Admiral Pump Mount Drum Cover111 23
Page 30 and 31: Admiral Outlet Accessories - 920 Ou
Page 32 and 33: Admiral Fluid Accessories - Siphon
Page 34 and 35: Admiral Outlet Accessories1 2 3 4 5
Page 36: Admiral Key Accessories and Service

SPEEFLO Admiral - Paint Sprayers, HVLP Sprayers, Powered Rollers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?