Standard range - Belting Ware

More documents

Recommendations

Info

Diagram 3 Speed of the small timing pulley [min -1 ] 14000 10000 8000 6000 4000 2000 1000 800 600 400 200 100 80 60 40 20 Guidelines for the selection of the timing belt optibelt OMEGA Design power P B = P x c 2 [kW] see also Optibelt CAP drive calculation software at www.optibelt.com 10 0.1 0.2 0.4 0.6 1 2 3 4 6 8 10 20 40 60 100 200 400 700 1000 14000 10000 8000 6000 4000 2000 1000 800 600 400 200 100 80 60 40 20 10 Speed of the small timing pulley [min -1 ] 25
Total service faktor c 2 26 Calculation optibelt OMEGA HL/HP and optibelt OMEGA Service factors The total service factor c2 consists of the basic service factor c0 and two additional factors c3 and c6. c 2 = c 0 + c 3 + c 6 c 2 ≥ M A/M N Recommendation for drives with frequent starts and stops Table 1 Basic service factor c 0 Type of loading and examples of prime movers Light drives, shock free and steady running Measuring devices Film cameras Office machines Belt conveyors (light-weight materials) Medium duty drives, intermittent operation with low to medium shock loading Mixers Kitchen appliances Printing machines Textile machines Packaging machines Belt conveyors (medium to heavy materials) Heavy duty drives, intermittent operation with medium to high shock loading Machine tools Woodworking machines Eccentric drives Conveyor systems (heavy materials) Very heavy duty drives, continuous operation with severe shock loading Mills Calenders Extruders Piston pumps and piston compressors Lifting devices Basic service factor c 0 The basic service factor c 0 takes account of the daily operating time and the type of prime mover and driven machine. Since it is not possible to combine every type of prime mover, driven machine and operating conditions into a single table, the basic service factors should be considered as guide values. The assessment of the driven machine depends on the type of loading on that machine. Steady operation Electric motor High speed turbine Piston engine with a large number of cylinders Type of basic load and examples of driven machines Intermittent operation Hydraulic motor Low speed turbine Piston engine with a small number of cylinders Basic service factor c 0 during daily operating period until 16 h more than 16 h until 16 h more than 16 h 1.3 1.4 1.4 1.5 1.6 1.7 1.8 1.9 1.8 1.9 2.0 2.1 2.0 2.1 2.2 2.3
Page 1 and 2: NEW OMEGA HL OMEGA 5M HP FOR DRIVES
Page 3 and 4: Produktionsstätten und Vertriebsor
Page 5 and 6: 4 Properties of optibelt OMEGA timi
Page 7 and 8: Construction 6 Top surface Tension
Page 9 and 10: 8 Belt designation Order example: S
Page 11 and 12: Top surface A durable and flexible
Page 13 and 14: Order example: Timing belts: Optibe
Page 15 and 16: Order example: 14 Belt designation
Page 17 and 18: Construction 16 Product description
Page 19 and 20: 18 111 3M 111 37 129 3M 129 43 141
Page 21 and 22: Order example: Timing belts: Optibe
Page 23 and 24: 22 Calculation optibelt OMEGA HL/HP
Page 25: Diagram 2 Speed of the small timing
Page 29 and 30: Prime mover Electric motor 50 Hz St
Page 31 and 32: 30 Calculation optibelt OMEGA HL/HP
Page 33 and 34: 32 Speed of the small timing pulley
Page 45 and 46: 44 Number of teeth 10 9.55 8.79 11
Page 47 and 48: 46 Number of teeth Standard timing
Page 49 and 50: 48 optibelt ZRS HTD ® timing pulle
Page 51 and 52: optibelt ZRS HTD ® timing pulleys
Page 59 and 60: Taper bush 58 optibelt ZRS HTD ® t
Page 61 and 62: Taper bush 60 optibelt ZRS HTD ® t
Page 63 and 64: Bore diameter d 2 (mm) Tightening t
Page 65 and 66: Permissible variation in tooth pitc
Page 67 and 68: Flanged pulleys For the guidance of
Page 69 and 70: 68 Design hints Problems - Causes -
Page 71 and 72: Details of the drive: 70
Page 73 and 74: The Optibelt offer is intended for

Standard range - Belting Ware

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?