DENAR® TRACK II SYSTEM - Whip Mix

More documents

Recommendations

Info

FIG. 16FIG. 18FIG. 2012FIG. 17the fingers as shown in Figure 17. Thepatient’s inter-condylar distance is themeasurement indicated on the scale (seeFigure 19). Record this measurement.Loosen the finger screw on the measuringbow, slide the bow open, andremove the entire facebow from thepatient.FIG. 19Detach the measuring bow from thetransfer jig by loosening the finger screw(see Figure 20). Having completed theprocedures involving the patient, thebitefork assembly (see Figure 21) may belabeled with the patient’s name and setaside while the measuring bow portioncan be used with an additional biteforkassembly for the next patient.FIG. 21Note: The metal bitefork, vertical shaftand earpieces can be sterilized in anautoclave EXCEPT for the black fingerscrews on the #1 and #2 clamps.Remove the finger screws (and spacers)before autoclaving or use cold sterilization.Sterilize bitefork before each use.
<strong>II</strong>I MOUNTING THE CASTSA benefit of using the Denar ® SlidematicFacebow is that multiple transfer jigsmay be used with only one measuringbow. Although it is not always recommended,the mounting of the maxillarycast can be delegated to the laboratory,involving no loss of accuracy and noperiod of time without facebow transfercapability in the dental office. The laboratorycan attain an articulator index fortheir own Denar ® articulator and mountthe maxillary cast using only the biteforkassembly from the dental office. Eacharticulator index positions the biteforkassembly on any Denar ® articulator sothat the relationship with the condylesrecorded on the patient is accuratelyreproduced on the articulator.Mounting the Maxillary CastReplace the incisal table on the articulatorwith the articulator index (see Fig.22). With the numbers on clamps #1 and#2 in the upright position, secure thereference pin of the bitefork assembly inthe hole of the articulator index. Tightenthe lockscrew on the front edge of theindex (see Fig. 23).Attach a mounting plate to the upperbow. Be sure that the incisal pin is at thezero position and that the upper bow islevel and parallel to the table top.FIG. 22The position that the incisal pin sits onthe articulator index is determined by thetype of incisal pin being used. The incisalpin (110092) with the long centric adjustmentfoot (used with the 110109 or110241 incisal table) sits on the highestsection of the movable insert. The roundlong incisal pin (300042, used with the110193 incisal table) sits in the center ofthe index. The round, short incisal pin(300200-1), used with the 110240 incisaltable) sits on the movable metal piece inFIG. 23the center of the index (see Fig. 24). Insituations where the Slidematic facebowis being used with the same articulator,secure the movable metal insert with adrop of wax once the insert’s appropriatelocation has been determined.13
Page 5: Table of ContentsI. The Track II Ar
Page 10 and 11: 10MEASURING BOW41. earplug2. anteri
Page 14 and 15: Mounting the Mandibular CastAttach
Page 16 and 17: 16IMMEDIATE SIDESHIFT1. Arbitrary a
Page 18 and 19: APPENDIX A-D31AB FACEBOW/EARBOWThe
Page 20 and 21: APPENDIX C-ACCESSORIESIncisal Pins
Page 24: Whip Mix Corporation361 Farmington

DENAR® TRACK II SYSTEM - Whip Mix

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?