PC5132-433 install.pdf

More documents

Recommendations

Info

I N T R O D U C T I O N1.3 Compatible Wireless DevicesPlease refer to the Instruction sheets of the following devices for more information.The PC5132-433 v4.X can receive signals from the following devices:• WLS904P-433 Motion Detector • WLS912-433 Glass Break Detector• WLS906-433 Smoke Detector • WLS907-433 Door/Window Contact• WLS914-433 Pet-Immune PIR • WLS909-433 Wireless Key• WLS919-433 Wireless Key • WLS925L-433 Mini Door/Window Contact1.4 BatteriesThe wireless devices, with the exception of the WLS925L transmitter and theWLS919-433 wireless key, are designed to use only Energizer Alkaline batteries (byEveready). For the WLS919-433, use only FDK CR2032 type lithium batteries.NOTE: Do not use other brands of batteries. Using any other brand may affect systemoperation.2
PC5132-433 Set Up & WiringS E C T I O N 2This section describes how to set up and wire the PC5132-433 module.2.1 Unpack the PC5132-433Check that the following parts are in your PC5132-433 package:• PC5132-433 PCB• Diversity antennae• PC5132-433 plastic cabinet • Hardware for mounting the cabinet2.2 Choose a Mounting Location for the PC5132-433NOTE: Mount the PC5132-433 receiver and wireless devices after you have doneplacement tests with the wireless devices (see sections 5.1 and 5.2).Find a place that is:• Dry• Central to the proposed placement of all wireless devices• As high as possible• Far from sources of interference, including: electrical noise (computers,televisions and electric motors in appliances and heating and airconditioning units); large metal objects like heating ducts and plumbingwhich may shield the antenna.Make sure that electrical wires will not run over the antenna(s) of the module whenit is mounted.When mounting the PC5132-433 in a basement, place the module as high and asclose to the underside of the first floor as possible. The range of the module will bereduced if the unit is mounted below ground level.2.3 Installing the AntennasThe two antennas must be screwed into the terminals marked ANT1 and ANT2, not GND1and GND2. Also they must be installed as indicated in the following two diagrams:Do not install the antennas as indicated in the following diagrams:If the antennas are installed incorrectly the PC5132-433 may notreliably receive signals from the transmitters.2.4 Connect the PC5132-433 ReceiverCAUTION: Remove all power from the systemwhile connecting modules to the Keybus.Connect the PC5132-433 to the four-wire Keybusof the control panel according to the followingdiagram.After you have completed the wiring, reconnectthe power to the security system.Now that you have wired the PC5132-433, you should enroll and program thewireless devices. See section 3 for instructions.3
Page 1 and 2: • W A R N I N G •This manual co
Page 3 and 4: Table of ContentsC O N T E N T SInt
Page 5: IntroductionS E C T I O N 1This man
Page 10 and 11: W I R E L E S S D E V I C E S3.4 Id
Page 12 and 13: O T H E R P R O G R A M M I N GIf t
Page 14 and 15: Testing & MountingS E C T I O N 55.
Page 16 and 17: 5.2 Mount the PC5132-433 and Wirele
Page 18 and 19: TroubleshootingS E C T I O N 71. Wh
Page 20 and 21: P R O G R A M M I N G W O R K S H E
Page 22 and 23: P R O G R A M M I N G W O R K S H E
Page 24 and 25: Guidelines for Locating Smoke Detec
Page 26 and 27: LIMITED WARRANTYDigital Security Co
Page 28: ©2003 Digital Security Controls Lt

PC5132-433 install.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?