1 - ГрандСервис. Телекоммуникационное оборудование

BYAJHVFWBZ LKZ PFRFPJD13CBL-HS2/V/3/@ One DHS channel operating in clock mode 3 toV.35 DTECBL-HS2/R/1/@ One DHS channel operating in clock mode 1 toV.36/RS-449 DTECBL-HS2/R/2/@ One DHS channel operating in clock mode 2 toV.36/RS-449 DTECBL-HS2/R/3/@ One DHS channel operating in clock mode 3 toV.36/RS-449 DTECBL-HS2/X/1/@ One DHS channel operating in clock mode 1 toX.21 DTECBL-R-STM-1DXC-STM-1 SDH 42 x E1 expansion module’s2m cable, 11 RJ-45 connectorsCBL-R-STM-1E/DIN/20 DXC-STM-1 SDH 3 x E3 and 3 x T3 expansion module’s20m cable, 8 Din connectors and an open endCBL-R-STM-1/ALM DXC-STM-1 SDH alarm cableManagement Software/HardwareRV-EEM-SW/c R-STM-1E Element Manager for Win 95/98 PCand small networks of up to 10 network elementsRV-EINM-SW/d R-STM-1E Integrated Network Manager for UNIXplatform, supporting MAP products andunlimited network elementsNote: When ordering RV-EINM-SW, you must also purchase the adequateRV-IN-HW, RV-EEM-SW/1 for IP address configuration and HPOV licenseRV-IN-HW/e UNIX workstation (mandatory for RV-EINM-SW)~ Specify power supply48 for –48 VDC operation100 for 100 VAC operation (DXC-2 only)115 for 115 VAC operation (DXC-2 only)230 for 230 VAC operation (DXC-2 only)AC for 100–240 VAC operation (not available for DXC-2)& Specify interface (default is T1 in port 1 and E1 in port 2)2T1 Dual T1 ports2E1 Dual E1 ports% Specify line interface (default is without CSU/LTU)C1 CSU/LTU in port 1C2 CSU/LTU in port 2? Specify management port interfaceUTP for Ethernet 10/100BaseTV24 for V.24/RS-232* Specify R for redundancy: system redundancy (2 power suppliesin DXC-4; 2 power supplies and 2 common logic for other DXCchassis), or two interfaces in DFSTM-1 modules (note: ifredundancy port is not identical to the main one, specifyInterface type for the redundant port - /R/CX for coax on thesecondary port or /R for interface to the one on the first port)$ Specify link interface optionsBP Port bypassC Built-in CSU or LTU (copper interface only)BP/C Built-in CSU (T1) or LTU (E1) and optional portbypass (copper interface only)#+ Specify optional optical interface (default is G.703 electricalinterface)# ST for ST-type connectorSC for SC-type connectorFC for FC/PC-type connector+ CX for copper interface (for DFSTM-1 moduleredundancy port only)85 for 850 nm, multimode (not available forDXC-STM-1)13L for 1310 nm, single mode, laser diode15L for 1550 nm, single mode, laser diode< Specify line interface typeB for balanced RJ-45 interfaceU for unbalanced BNC interface^ Specify interfaceV24 for V.24 interface (for DHS only)V35 for V.35 interface449 for RS-449 interface (for DIM only)530 for RS-530 interfaceX21 for X.21 interfaceE1 for E1 interface (E1 over two T1 links) (for DIM only)HSSI for high speed serial interface (for DIM only)ETUB for Ethernet bridge port with 10/100BaseT (UTP)interface (IR-ETH/QN)ETUR for Ethernet router port with 10BaseT (UTP)interface (IR-IP)@ Specify cable connector typeF for female connectorM for male connectora for number of tributary ports4 4 E1/T1 ports8 8 E1/T1 portsc Specify number of network elements for RV-EEM1, 2, … 10 network elements to be managedd Specify number of network elements for RV-EINM1, 2, … network elements to be managede Specify Integrated Network workstation configuration1 for up to 50 NEs2 for up to 100 NEs3 for up to 250 NEs4 for up to 500 NEsDXC-100 SystemDXC-100/MNPower Supply ModulesDXC-100M-PS/ACDXC-100M-PS/486U NEBS-3 certified modular optional redundantDACS rack, no system modules, no PS modules6U 100–240 VAC power supply module6U -48 VDC power supply moduleBYAJHVFWBZ LKZ PFRFPJDRAD Data Communications 2005 Rfnfkju163