TMF Series - HANSA-TMP

Heavy Duty Orbit Motors (Disc Valve)TMF MotorsDIMENSIONS AND MOUNTING DATA - TMFA606x5/8-18 UNF605x 1572[2.835]5x 15ø180[7.087]ø172[6.772]ø180[7.087]ø189[7.441]18 6[.708] [.236]10xø14,2 +0,15[.559 +.0059]ø238[9.37]ø152,4[6.0]ø210[8.268]P (A,B)21±0,15[.827±.0059]ø109,22[4.3]7[.276]12[.472]Warning:113 max[4.449]5[.197]L3max LDrain line should always be used.L1L242±0,15[1.654±.0059]42±0,15[1.654±.0059]TPort BPort Aø139[5.472]P (A, B) : 2x1 1/16-12 UN, O-ring port17 mm [.669 in] depthT : 9/16-18 UNF, O-ring port12 mm [.472 in] depthmm [in]Standard RotationViewed from Shaft EndPort A Pressurized - CWPort B Pressurized -CCWReverse RotationViewed from Shaft EndPort A Pressurized - CCWPort B Pressurized -CWTypeTMFA200TMFA 250TMFA 315TMFA 400TMFA 470TMFA 500TMFA 630TMFA 725L,mm [ in] L, 1 mm [in]126 [ 4.96].98 [25]132.3 [ 5.21]31,3 [ 1.23]141.5[ 5.57]40,5 [ 1.59]152 [ 5.98]51 [ 2.01]160 [ 6.30]59 [ 2.32]166 [ 6.54]162 [ 6.38]171 [ 6.73]65 [ 2.56]61 [ 2.40]70 [ 2.76]L, 2 mm [in]83 [3.268]89.3 [3.516]98.5 [3.878]109 [4.291]117 [4.606]123 [4.843]119 [4.69]128 [5.04]L, 3 mm [in]110,3 [ 4.34]116,6 [ 4.59]125,8 [4.95]136,3 [5.37]144,3 [5.68]150,3 [5.92]146,3 [5.76]155,3 [6.11]Pag. 24HT 03 / E / 301 / 0211 / E

Heavy Duty Orbit Motors (Disc Valve)TMF MotorsPERMISSIBLE SHAFT LOADSThe load diagram is valid for an average bearings life of 2000 hours at 100 RPMPraddaN120001000080006000400020000100.51 1.5 2 2.5 3 3.5 4 4.5 L, inPradlbs26000B24000220002000018000A16000140001200010000800060004000200020 30 40 50 60 70 80 90 100 110 120 L, mmA - Permissible radial shaft load.B - Max. radial shaft load. Any shaft load exceeding the values shown in the curvewill involve a risk of breakageORDER CODETMF1 2 3 4Pos.1 - Mounting Flangeomit - Thread hole flange, 5xM12x1,5 on ø140A - Thread hole flange, 6x5/8-18 UNF on ø152,4Pos.2 - Displacement code2002503154004705006307253 3- 201,4 [12.29] cm. /rev. [in. /rev.]3 3- 251,8 [15.36] cm. /rev. [in. /rev.]3 3- 326,3 [19.90] cm. /rev. [in. /rev.]3 3- 410,9 [25.06] cm. /rev. [in. /rev.]3 3- 475,0 [28.97] cm. /rev. [in. /rev.]3 3- 523,6 [31.95] cm. /rev. [in. /rev.]3 3- 631,2 [38.52] cm. /rev. [in. /rev.]3 3- 724, 3 [44.20] cm. /rev. [in. /rev.]Pos.3 - Special Features (see page 35)Pos. 4 - Design Seriesomit - Factory specifiedThe hydraulic motors are mangano-phosphatized as standard.HT 03 / E / 301 / 0211 / E Pag. 25