The First Solar Water Heater with an integrated - Thermal Products Inc

Venting OptionsSIDEWALL VENTING WITH TEE (INTAKE) ANDSIDEWALL VENTING COUPLING WITH EXHAUST TEE (INTAKE) ANDCOUPLING EXHAUST12"MIN.1"MIN.EXTERIOR WALLModelSolar Recovery CapacitiesGallonCapacityInput BTU/hrHeated WaterVolume ofGas Back-Upat First DrawRecovery Of Back Upin Minutes65˚ Rise90˚ RisePH199-119S 119 66,000–199000 61 GAL 10 MIN 14 MINPH199-80S 80 66,000–199000 41 GAL 7 MIN 10 MINPH130-119S 119 44,000–130000 61 GAL 16 MIN 21 MINPH130-80S 80 44,000–130000 41 GAL 11 MIN 15 MINEXHAUSTINTAKESUPPORT BRACKETSMUST BE USED ONALL HORIZONTALAND VERTICAL PIPING1"MIN.CONCENTRIC VENT KITPART# KGAVT0501CVT - 2"KGAVT0601CVT - 3"EXTERIOR WALLLEFT SIDE VIEWLEFT SIDE VIEWIMPORTANT:INTAKE LEG MUST BE FACING UPINTAKEEXHAUSTLP-201-CSIDEWALL VENTING WITH TEE (INTAKE) ANDSIDEWALL VENTING WITH TEE (INTAKE) ANDCOUPLING (EXHAUST)SUPPORT BRACKETSMUST BE USED ONALL HORIZONTALAND VERTICAL PIPINGLP-201-BSpecificationThe Phoenix Water Heater shall bemanufactured by Heat Transfer Products,Inc. with identification of model numberPH________. The water heater shall bea sealed combustion system, taking onlyoutside air for combustion and exhaustingthe flue gas with PVC Schedule 40 or 80PVC, or CPVC solid core pipe. The heateras well as all related intake air andexhaust intake air and exhaust gas pipingshall be approved for zero clearance toany combustible surface. The units totalcombined equivalent venting length,including fitting allowances for boththe intake air and exhaust gas shall notexceed 85’ (in the units native size asmanufactured and stated on the unitmodel product data sheet) in 2”, or 3” pipeor 125’ for the next size up of 3” or 4” fromthe heaters location.The solar heaters tank shall be constructedof 316L stainless steel. The primary gasfired condensing heat exchanger shall beconstructed of 90/10 cupronickel. Thesecondary gas fired heat exchanger shallbe constructed of 800H stainless steel and90/10 cupronickel. The tank insulation shallbe water blown foam 2” thick in the sidewall with a rating of R14.2 and 3” thick inthe top with a rating of R21.3. Insulationshall be enclosed in a plastic jacket on thesides as well as the top and bottom. Allcomponents shall be located on the frontof the heater for easy access andserviceability. All related hardware shallbe constructed of stainless steel studswith brass nuts for serviceability. All waterconnection nipples shall be constructed ofstainless steel and be attached to the sideof the tank. The top and bottom of the tankshall be smooth with no pipe tappings onthe top or legs on the bottom.Solar models shall have an additionalinternal heat exchanger on the bottom ofthe tank to connect to a solar system.The heaters shall be UL/ULC listed andwill exceed the minimum efficiencyrequirements of ASHRAE 90.1b -1992. Allheaters shall be approved in accordancewith ANSI Z 21.10.3. All heaters will besupplied with a factory installed ASMErated temperature and pressure reliefvalve. All heaters shall be supplied witha factory installed low water cutoff, andupper hot water sensor, and lower coldwater sensor. All heaters shall be furnishedwith a factory installed condensate trapassembly ready for easy connection to afield supplied condensate drain.The heater shall have an integrated digitalcontroller device with integral diagnostics,LED fault and temperature settingsfor establishing set point, temperaturedifferential. Ignition shall be with directspark with ignition taking place at a pre-setignition speed for the burner blower. Thecontrol shall utilize an algorithm to fullyadjust the burner modulating firing ratewhile maintaining the desired temperature.The pre-mix stainless steel burner uses a120 volt motor with pulse wave modulationcontrol to change the fan speed, thus thecombustion air volume of fuel and airthrough the burner to establish an infiniteBTU input range equal to the water heatingset point requirement. The digital LEDcontrol display shall provide means, viapush buttons, for adjustments of operatingtemperatures, differential adjustment, ECOreset, service mode, and real time statusmode. In addition there shall be provided acomputer connection via laptop computerfor perpetual history including all faultcodes, and hours of operation above 50%of input, below 50% of input as well as realtime status reporting of all operations. Theburner assembly shall be mounted so as tobe easily removed as an integral unit foreasy serviceability.The heater shall be in compliance withthe NOx Emissions limit as set forth inSCAQMD Rule 1146.2 – 1998.The heater shall be factory assembled; testfired for correct BTU input and adjusted forproper combustion parameters. Completeoperating and installation instructionsshall be furnished with every heater aspackaged by the manufacturer with theheater for shipping.Copyright 2008www.htproducts.com LP-201 Rev. 2/1/08