Push Button R55F Series Fiber-Optic Color Mark Sensors - Multiprox

More documents

Recommendations

Info

R55F Series Fiber-Optic Color Mark SensorsR55F Series Sensor SpecificationsSupply InputSupply Protection CircuitryOutput ConfigurationOutput RatingOutput ProtectionOutput ResponseAdjustments(see pages 4 - 9)Indicator LEDsConstruction10 to 30V dc (10% maximum ripple) at less than 70 mA, exclusive of loadProtected against reverse polarity and transient voltagesBipolar (NPN and PNP)150 mA max each output @ 25°C (derate ≈ 1 mA per °C increase)OFF-state leakage current: < 5 µA @ 30V dcON-state saturation voltage: PNP Output < 1V @ 10 mA and 1.5V @ 150 mANPN Output < 200 mV @ 10 mA and 1V @ 150 mAProtected against false pulse on power-up and continuous overload or short-circuit of outputs.50 microsecondsNOTE: 100 millisecond delay on power-up; outputs do not conduct during this time.Using push buttons (“+” Dynamic and “-” Static):Manually adjust Switch Point using “+” or “-” buttonsDynamic TEACH (teach on-the-fly) sensitivity adjustmentStatic TEACH sensitivity adjustmentLight operate/Dark operateOFF Delay select: 0 milliseconds, 20 milliseconds or 40 millisecondsUsing Remote TEACH input (gray wire):Dynamic TEACH (teach on-the-fly) sensitivity adjustmentStatic TEACH sensitivity adjustmentLight operate/Dark operateOFF Delay select: 0 milliseconds, 20 milliseconds or 40 millisecondsPush button lockout for security10-segment (green) light bar indicates signal strengthLight Operate (green)Dark Operate (green)Outputs Conducting (yellow)OFF Delay (green): SETUP Mode: OFF — no delay RUN Mode: OFF — no delayFlashing — 20 ms delayON — 20 or 40 ms DelayON — 40 ms delayHousing: Black ABS/polycarbonate blend; nylon fiber clipmounts to standard 35 mm DIN rail1 stainless steel right angle bracket and 1 PBT polyester bracket for mounting to flat surfaces also includedwith sensorEnvironmental Rating IEC IP67; NEMA 6ConnectionsOperating ConditionsApplication NotesPower: 2 m or 9 m PVC-jacketed 5-conductor cable or 5-pin Euro-style quick-disconnect (QD) connectorFibers: Fiber clip (no tool required)Temperature: -10° to +55° C (+14° to 131° F)Maximum Relative Humidity: 90% at 50° C (non-condensing)• Do not mount the fiber tip directly perpendicular to shiny surfaces; position it at approximately a 15° anglein relation to the sensing target• Minimize web or product “flutter” whenever possible to maximize sensing reliabilitypage 10Banner Engineering Corp. • Minneapolis, U.S.A.www.bannerengineering.com • Tel: 763.544.3164
R55F Series Fiber-Optic Color Mark SensorsCabled ModelsR55F Series Sensor HookupsQuick-Disconnect ModelsbnbuwhbkgyLoadLoad+10-30V dc–bnbuwhbkgyLoadLoad+10-30V dc–Remote TeachRemote TeachBoth brackets are included with sensor.Mounting BracketsSMBR55FRA• Side-mounting bracket• 19 ga stainless steelSMBR55F01• Flat-mounting bracket• Molded PBT polyester3.5 mm(0.14")7.2 mm(0.28")4x 5.0 mm(0.20")40.0 mm(1.58")4.5 mm(0.18")2x ø5.4 mm(0.21")65.0 mm(2.56")15.0 mm(0.59")29.5 mm(1.16")6.0 mm(0.24")35.0 mm(1.40") 50.8 mm(2.00")35.0 mm(1.38")20.0 mm(0.79")4x R2.5(0.10")2.5 mm(0.10")4.5 mm(0.18")10.0 mm(0.40")7.5 mm(0.30")30.4 mm(1.20")50.8 mm(2.00")64.0 mm(2.52")Quick-Disconnect (QD) CablesStyle Model Length Connector5-Pin EuroMQDC1-506MQDC1-515MQDC1-530MQDC1-506RAMQDC1-515RAMQDC1-530RA2 m (6.5')5 m (15')9 m (30')2 m (6.5')5 m (15')9 m (30')StraightStraightStraightRight-angleRight-angleRight-angleBrown WireBlack WireWhite WireBlue WireGray WireBanner Engineering Corp. • Minneapolis, U.S.A.www.bannerengineering.com • Tel: 763.544.3164page 11
Page 1 and 2: R55F Series Fiber-Optic Color Mark
Page 5 and 6: LOLOLOLOLOR55F Series Fiber-Optic C
Page 9: R55F Series Fiber-Optic Color Mark

Push Button R55F Series Fiber-Optic Color Mark Sensors - Multiprox

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?