(pm halo) helmet assembly - Gentex Corporation

More documents

Recommendations

Info

Optional ComponentsThe following optionalcomponents are available:• Flex boom helmetmicrophone(Figure 3). Availablein 150-ohm and5-ohm versions, themicrophone attachesto the helmet shellinterior with attachinghardware.• Earphones(Figure 4).Earphone optionsinclude 19-ohm,19-ohm waterproof,300-ohm, 600-ohm,1000-ohm waterproof,and 1200-ohmwaterproof.NOTE: For helmetswith leather earpads,earphones withattached cords arerequired.• Communicationscables (Figure 5).Options includecables for use withan oxygen maskmicrophone and/or ahelmet microphone.NOTE: Cables with4-pin plugs are foruse with single radioadapters. Cables with5-pin plugs are foruse with dual radioadapters.(Continued on nextpage)Figure 3. MicrophoneDOWN LEAD CABLE 03C11797-2(Used with helmet microphone ormask microphone cable, 9" long)4-pin plug (single radio)MASK MICROPHONE CABLE, 9" long, 69C2080-3(Used with DOWN LEAD CABLE 03C11797-2 or -4)DOWN LEAD CABLE 03C11797-4(Similar to cable 03C11797-2, butwith 5-pin plug for dual radio adapters)5-pin plug (dual radio)DOWN LEAD CABLE WITH SWITCH 03C11797-6(Permits switching between helmet microphoneand oxygen mask microphone; used withmask microphone cable, 32" long)Switch4-pin plug (single radio)Figure 4. EarphonesMASK MICROPHONE CABLE, 32" long, 69C2080-4(Used with DOWN LEAD CABLE WITH SWITCH above)EAR-TO-EAR CABLE 03B11796-1(Used with oxygen mask communications cableor DOWN LEAD CABLE WITH SWITCH below)Switch4-pin plug (single radio)DOWN LEAD CABLE WITH SWITCH 06D12449-2Figure 5. Cables4
• Mask attachmentcomponents (Figure6). The following typesare available: fixedbayonet receivers,mask snap adaptors,and a low profilebayonet system. Eachtype is provided inpairs along withattaching hardware.• Suspension systems(Figure 7). Optionsinclude thethermoplastic liner(TPL), the adjustablepad suspension(included with theMedium/Large basichelmets), and theXLINER (includedwith the X-Large Widebasic helmets). Inaddition, the XLINER isavailable for bothhelmet sizes in1/2-inch and 3/4-inchthicknesses.• Nape pad (Figure 8).The leather-coveredfoam nape pad(included with X-LargeWide helmets) isrequired for use withthe XLINER and theTPL.(Continued on next page)WARNINGIf an XLINER or a TPL isinstalled into a helmet,ensure that a nape pad isinstalled on the napestrap. Failure to do socould result in injury.XLINER and TPL are registeredtrademarks of Gentex Corporation.Fixed bayonetreceiver kitAnti-snag bayonetreceiver kitMask snap adapter kitFigure 6. Mask Attachment ComponentsTPLAdjustable padsuspensionAnti-snag bayonetreceiver kit, no receiversFigure 7. Suspension SystemsFigure 8. Nape PadXLINER5
Page 1: Operation InstructionsPARAMASTERHIG
Page 4 and 5: SAFETY NOTICEWARNINGProper fitting,
Page 6 and 7: Basic HelmetAll basic helmets (Figu
Page 10 and 11: • Snap-on visors(Figure 9). Snap-
Page 12 and 13: 2. Adjust the nape strap (Figure 13
Page 14 and 15: Attaching Step-in Visor1. Don the h
Page 16 and 17: Operating Communications SystemDepe
Page 18 and 19: Using 9" Mask Microphone Cable with
Page 20 and 21: Using 32" Mask Microphone Cable and
Page 22 and 23: Using Ear-To-Ear CableYou can use t
Page 24 and 25: 3. To use the ear-to-ear cablewith
Page 26 and 27: Periodic InspectionOperating person
Page 28 and 29: 8. Inspect the bayonet receivers as
Page 30 and 31: PARTS LISTSFollowing are the parts
Page 32 and 33: Optional ComponentsMicrophones (Fig
Page 34 and 35: Snap-on Visors(Figure 44)• MBU-12
Page 36 and 37: Single Radio Adapters (Figure 48)fo
Page 38 and 39: Specialty Adapters (Figure 51)05B12
Page 40: TP0257 REV. 4 FEBRUARY 2012

(pm halo) helmet assembly - Gentex Corporation

Create successful ePaper yourself

Delete template?

Save as template?