REACT 350Â® II - Energy Absorption Systems

More documents

Recommendations

Info

5) Tension Restraining CablesUse the nuts on the threaded end of the cables to tension the cables (See Figure 22).When properly tensioned, the cables should not deflect more than 75 mm [3”] with 45 kg[100 lb.] downward pressure.Attach Nose Cover1. Ensure appropriate Nose Cover is attached (See Figure 23). The Nose Cover Selectionbelow will assist in your selection and you should refer to local standards and “Manualon Uniform Traffic Control Devices” (MUTCD) for nose.Barrier Barrier BarrierTraffic Traffic Traffic TrafficTraffic on Right Traffic on Both Sides Traffic on LeftSide of System of System Side of SystemFigure 23 - Nose Cover Selection2. Align 1” diameter hole in Nose Cover with 1” diameter hole in Cylinder (See Figure 24).3. Screw 1/4" self-drilling screw into Cylinder punching through reflective tape and into theexisting holes in Nose Cover until head of fastener is flush (10 places) (See Detail B).Align 1" Hole(For Assembly ofSystem Pullout DeviceSeeDetail BNose CoverP/N 617966 - R & LP/N 617965 - GoreFigure 24 - Nose Cover AttachmentDetail B1/4" Self-DrillingP/N 116891www.energyabsorption.com Revision A July 2013www.highwayguardrail.com 31 All rights in copyright reserved
Affix Side Mount ReflectorsRefer to local standards and “Manual on Uniform Traffic Control Devices” (MUTCD) forreflectors.For Side Mount Reflectors, attach to traffic side(s) of the system with the white side facingtraffic by screwing #8 self-tapping screws through the reflector and into the Cylinder untilhead of fastener is flush (2 places per reflector) (See Figure 25).White Facing Traffic,Amber Opposite50 mm [2"]ReflectorP/N 611305Figure 25 - Side Mounted Reflector#8 Flat WasherP/N 117989#8 Self-Drilling ScrewP/N 116943www.energyabsorption.com Revision A July 2013www.highwayguardrail.com 32 All rights in copyright reserved
Page 8 and 9: System OverviewThe REACT 350 ® II
Page 10 and 11: Miscellaneous Traffic control equip
Page 12 and 13: Model Number DescriptionBSelf‐Con
Page 14 and 15: System DesignSelf-Contained BackupT
Page 16 and 17: Offsetting the SystemIf space permi
Page 18 and 19: Foundation/AnchoringConcrete Instal
Page 20 and 21: Foundation/Anchoring AssistanceCont
Page 22 and 23: JointsThe REACT 350 ® II system ma
Page 24 and 25: 2) Determining the Base Point & Cen
Page 26 and 27: 4) Drill and Set AnchorsUse the hol
Page 28 and 29: Warning: Once the grout has hardene
Page 30 and 31: 4) Attach Restraining CablesWarning
Page 34 and 35: Optional Debris CoversTo attach Opt
Page 36 and 37: 3) Clean the holesTable A: MP-3 ®
Page 38: Horizontal AssembliesThe Horizontal
Page 41 and 42: Recycling InformationWhen parts nee
Page 43 and 44: Post-Impact Instructions1. Deploy t
Page 45 and 46: DWG R626C036UREACT 350 ® II TL-3 w
Page 47 and 48: DWG 3535006-0000REACT 350 ® II Tra
Page 49 and 50: DWG 3535048-0000 Sheet 2 of 3www.en
Page 51 and 52: DWG 605028 Sheet 1 of 2REACT 350 ®
Page 55 and 56: DWG 605020 Sheet 3 of 3www.energyab
Page 59 and 60: DWG 617967REACT 350 ® Nose Cover A
Page 65 and 66: DWG 3535043-0000REACT 350 ® Misc.
Page 67 and 68: DWG 618102REACT 350 ® Debris Cover
Page 69 and 70: DWG 3535113-0000REACT 350 ® Drivab
Page 71 and 72: Notes:www.energyabsorption.com Revi

REACT 350Â® II - Energy Absorption Systems

Create successful ePaper yourself

Delete template?

Save as template?