V454501 Single Preset Counter - Danaher Specialty Products

More documents

Recommendations

Info

I N S T A L L A T I O NRelay OutputConnect AC or DC load circuits to Terminals 9, 10 & 11(see below) as required. Do not route load wiring nearcount input or transistor output signals.Open Collector OutputConnect Terminals 12 (open collector) and 4 (COM) to solid statedevices as shown below (upper circuit). To drive DC relay coils,connect Terminal 12 and V+ (Terminal 1) as shown on below (lowercircuit). Suppress switching transients with a suppression diode,connected as shown.48m11048m10mm (approx.)Panel MountingMake cut-out(s) according to the details inthe diagram on the right. The maximumpanel thickness is 6 mm.45m45mSingleInstallatio(48n - 4)mmMultiple Installation (nCounters)CAUTIONDo not remove the panelgasket from the Counter asthis may result ininadequate clamping of theCounter in the mountingpanel.Insert the rear of the Counter housingthrough the cut-out (from the front of themounting panel) and hold the Counterlightly in position against the panel. Ensurethat the panel gasket is not distorted and thatthe Controller is positioned squarely againstthe mounting panel. Apply pressure to thefront panel bezel only. Slide the mountingbracket in place (see right) and push itforward until it is firmly in contact with therear face of the mounting panel (tongues onthe bracket should engage in matchingrachet positions on the Counter housing andthe mounting bracket springs should pushfirmly against the mounting panel rear face).Rear face of mounting panelMounting bracketCounterhousingTongues on mounting bracketengage in ratchet slots on Counter housing
O P E R A T I O N1. Upper Display2. Lower Display9. PresetAnnunciator(ON when Presetvalue is shown in thelower display)8. Down6. Enter3. Program4. Preset Output Annunciator(ON when active)5. Reset Key7. Next KeyDown keyNext keyNOTETo abort changes to aparameter value, pressDown and Next togetherinstead of ENT.IMPORTANTIn Edit Mode, you mustpress the ENT key within15 seconds of the lastkeypress, otherwise thenew data will be lost andthe old data will berestored.Operator Mode: Used to change thecurrently-selected (flashing) digit.Depressing this key will decrement thevalue (wrap-around from 0 to 9). If thekey is held continuously, the value willdecrement at the rate of 2/sec.Program Mode: Used to advance fromone parameter to the next. Once aparameter value has been selected forediting (through use of the Next key),depressing this key will decrement thevalue (wrap-around from 0 to 9). If thekey is held continuously, the value willdecrement at the rate of 2/sec.Configuration Mode: Used to advancefrom one parameter to the next.ENT keyOperator Mode/Program Mode:Confirms an edited value (display willcease flashing after the ENT key isdepressed).Configuration Mode: Confirmssetting/value selection (display will ceaseflashing after the ENT key is depressed).For information on Operator Mode, see Page 6.For information on Program Mode, see Page 7.For information on Configuration Mode, see Page 8.Operator Mode: Used to select aparameter for editing (left-most digit willstart to flash) and to move between thedigits. Once the proper digit is selected(flashing) with the Next key, its value canbe altered through use of the Down key.Program Mode: Used to select aparameter for editing (left-most digit willstart to flash) and to move between thedigits. Once the proper digit is selected(flashing) with the Next key, its value canbe altered through use of the Down key.For Decimal Point Position, this keyscrolls through the available choices.Configuration Mode: Used to select aparameter for editing and to scroll throughavailable choices.RST keyOperator Mode/Program Mode: Resetscount value to either zero or Preset value(based on the setting of the CountDirection parameter in ConfigurationMode). Also releases latched outputs.Configuration Mode: ExitsConfiguration Mode when held down for 2seconds.NOTE: The RST key will not be activeunless enabled in Configuration Mode.
Page 1 and 2: IntroductionA new standard of perfo
Page 3: I N S T A L L A T I O NIMPORTANT: I
Page 7 and 8: WARNING!Changing ProgramMode parame
Page 9 and 10: A P P E N D I X AInput PowerAC:DC:P
Page 11 and 12: N O T E S11

V454501 Single Preset Counter - Danaher Specialty Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?