Parts Diagram and DescriptionRef. Part DescriptionPart Numbers1 Arm Cap (2) Included in Kit B2 Arm Nut (2) Included in Kit B3 Arm Shaft Included in Kit B4 Reverse Spoon Bracket Assembly 71-P003825 Reverse Arm Assembly 71-P508096 Nozzle Retainer 71-P503027 Forward Spoon Bracket Assembly 71-P003648 Forward Arm Assembly 71-P508079 Arm Ball Bearing 71-P0032410 Forward Arm Spring 71-P5029511 Trip Yoke Assembly 71-P5021512 Upper Yoke Bushing Included in Kit A13 Elbow/Range Tube Assembly 71-P5080314 O-Ring (2) Included in Kit A15 Brake Assembly 71-P5081416 Bearing Assembly 71-P5097517 Friction Collar (2 Required)` 71-P5011618 Snap Ring 71-P5034419 Ball Bearing 71-P5054920 Lock Nut 71-P5079621 O-Ring 71-10215522 Bearing Sleeve 71-P5079523 Lower Yoke Bushing Included in Kit A24 Trip Lever Bushing Included in Kit A25 Trip Lever Assembly 71-P5033126 Reverse Arm Spring 71-P5029627 GNS-2005T Taper Nozzle (6) Set L0025028 GNS-2005O Ring Nozzle (6) Set L00255Accessories29 Bearing Wrench 71-P5069730 Riser Installation Kit 71-P0036831 Rear Counterweight L0026032 Glycerin Filled Pressure Gauge (not shown) 71-P00080Spare Parts KitA Maintenance Kit 71-P50364B Arm Shaft Kit 71-P50365
Specifications (For Specifiers)The full circle or part circle impulsedrive sprinkler shall be a single nozzletype, capable of covering________(feet/meters) radius, at________ (PSI/bars) with a dischargerate of ______ (GPM/M 3 H). Thesprinkler body and bearing sleeveshall be of heat treated, castaluminum. Straightening vanes shallbe integral to the body. The sprinklerarm, springs, fulcrum shafts, and tripmechanisms shall be stainless steel.The drive nozzle trajectory shall be 23degrees from horizontal.The rotation of the sprinkler shall beaccomplished by a spring loaded,vertical oscillating arms, actuated bythe outlet water stream. The partcircle models shall have a slow-reversefeature for reduced vibration andgreater safety.The nozzle shall be of durable,chemically resistant plastic and shallbe easily replaceable. A set of six taperbore nozzles shall be included withthe gun - 21, 23, 26, 28, 30, 33 mm.The nozzle size shall be molded intothe plastic for easy identification.The bearing assembly shall bepermanently sealed and packed 70%with a wide temperature range, waterresistant silicone grease. The brakemechanism will be spring loaded andself-adjusting.On part circle models, adjustablefriction collars will be supplied to setarc adjustments without the use oftools, and the bearing assembly will bemarked in ten degree increments tofacilitate adjustments.The F2004 shall be for full circleoperation only. The SR2005 shallhave adjustable part circle or fullcircle operation.The sprinkler shall have a DN 804 or 6 hole patterns with a 2 mm (.08”)neoprene gasket and bolt kit shall besupplied with the gun.An optional (NPT/BSP) flangeadapter will be supplied to adapt theflange inlet to a (3”/76 mm) femaleinlet.The sprinkler shall carry a three yearwarranty against original defects inmaterial or workmanship inagricultural applications. Thesprinkler shall be supplied by RainBird Corporation, Glendora,California.Rain Gun SafetyOperating Rain Guns remotely undercircumstances where the operatorcannot see the gun being activatedcan be dangerous if persons oranimals are close to the device. Whenactivated these guns can come onwith significant force. Operatorsshould also be aware of trip hazard,over-head obstruction, thrust, etc. fortheir applications, to prevent anybodily harm. If an operator has anyquestion pertaining to Rain GunSafety please contact your local dealeror Rain Bird representative.Rain Gun Warranty<strong>Ag</strong>ricultural Applications• Our latest generation of Rain Guns isbuilt on a legacy of knowledge, trust,and feedback from end users likeyou. Our warranty is simple and inline with Rain Bird’s reputation asthe most reliable agriculturalsprinkler in the world. To back upour claim, we offer the best warrantyin the agriculture industry. For allagricultural applications, we offer athree-year; no questions askedwarranty including free service orparts replacement. Productreplacement, full credit, or return inlieu of spare parts or service is atRain Bird’s discretion uponapproval. Approval may includeproduct testing.Non-agricultural Applications• We understand that Rain Guns areoften utilized in applications thatmay be more demanding thangeneral agricultural applications. Inthese circumstances, Rain Birdoffers an eighteen month warrantyincluding free service or partsreplacement, but excludes coveragein the following general applicationsor environments:• Electrolytic conditions, such as highsalt environments or salt water sprayapplications• Applications where environmentalconditions are not compatible withthe materials used in Rain Guns• Caustic or corrosive chemicalconditions or spray applications• Abrasive fluid spray applicationsRain Bird Corporation<strong>Ag</strong>ri-Products Division633 W. Foothill Blvd.Glendora, CA 91741-2469Phone: (800) 435-5624Fax: (626) 852-7310Rain Bird International, Inc.145 N. Grand Ave.Glendora, CA 91741-2469Phone: (626) 963-9311Fax: (626) 963-42871-800-HELLO-AG6am-6pm MST M-Fwww.rainbird.comRain Bird. The Intelligent Use of Water. ® Registered Trademark of Rain Bird Corporation© <strong>2003</strong> Rain Bird Corporation 3/03PN L207