Micro Motion® Insertion Density and Viscosity Meter Accessories

Flow-through chambersAbout the flow-through chamberMicro Motion designed the flow-through chamber accessory to be used with all fork density and viscositymeters. This accessory simplifies the installation of the meters in in-line and slipstream/bypass applications.The flow-through chamber has been designed to connect to nominal pipe bores between 1˝ (DN25) and3˝ (DN80), with a number of available flange variants. This chamber conditions the flow of the product overthe meter so that flow rates of up to 20 m 3 /hr (88 gal/min) at temperatures up to 200 °C (392 °F) can bereliably measured.The flow-through chamber provides the greatest flexibility to process variations, and should be consideredwhere temperature and pressure changes are significant and the possibility of entrained air exists.Features• Provides 1˝ to 3˝ pipe bore connection• Can be used with fluid viscosities up to 1000 cP• Can be used with line pressures up to 100 bar• Can be used where line temperature is up to 200°C• Provides connections to meters with a cone-seat or flange fittingPipeline weldoletsAbout the pipeline weldoletsPipeline weldolets only can be used with meter installations that use a cone-seat fitting. The pipelineweldolets allow the meter to be installed directly into the side of pipes that have a 4˝ or greater diameter.Pipeline weldolets are available in two styles:• Free stream – where the fork is fully exposed to the flow (free-stream meter calibration)• Recessed – where the fork is fully withdrawn from the flow (2˝ schedule 40 calibration)The following limits apply, depending on the pipeline weldolet installation:• The velocity limits for free-stream installation are: > 0.3 to < 1.5 ft/s (> 0.1 to < 0.5 m/s)• The velocity limits for recessed mounting are: > 1.5 to < 15 ft/s (> 0.5 to < 5.0 m/s)• The maximum fluid viscosity for recessed mounting is: 200 cPPipe size should be increased or decreased to enable the velocity limits to be met. For example, where thereare no intermediate ranges – such as for pipe lines with flow velocities 0.4 to 0.6 m/s – the pipe diametermust be increased so that a free-steam weldolet can be used, or decreased so that a recessed weldolet canbe used. Be sure that the corresponding codes for the materials, the cone-seat fitting and the calibration arespecified for the associated fork sensor.Micro Motion Insertion Density and Viscosity Meter Accessories 3

Features• Provides connections for 4˝ or greater pipelines• Offers full-insertion or recessed mounting options• Provides cone-seat fitting meter connections for optimum performanceBlanking plugAbout the blanking plugA blanking plug is used to close the meter entry point, if at any time you need to remove the meter andrestore flowing conditions – such as for service or to flush the installation. The blanking plug is designed onlyfor meter installations that use a cone-seat fitting.Features• Consists of a securing nut and a cone-seat fitting plug, which provides the same sealing integrity as themeter• Can be used with any cone-seat version of the flow-through chamber and pipeline weldolet accessoriesDiagnostic and configuration toolsADView Software Tool FeaturesADView is a PC-based configuration anddiagnostics tool that runs on a Microsoft ® Windows ®platform, communicates with the density andviscosity meters through a standard serial port, andprovides the following functionality:• Setting up a serial link to communicate with thedensity and viscosity meters• Configuring the density and viscosity meters• Displaying data real-time or as a graph• Logging data to a file• Verifying correct operation of the system anddiagnosing faults• Loading and storing the Modbus register values• Read/write to individual Modbus registersProLink II Software Tool FeaturesThe ProLink II software tool (version 2.9 or later)can be used with the density and viscosity meters.ProLink II runs on a Microsoft Windows platform,communicates with the meters through a standardserial port or USB port, and provides the followingfunctionality:• Configuring the meter• Viewing and logging process parameters• Viewing meter diagnostics4 Micro Motion Insertion Density and Viscosity Meter Accessories

Installation practices and sizingAs a result of the superior installation flexibility of the Micro Motion fork density and viscosity meters, eachaccessory has been designed for a variety of application conditions. The following guides have beendesigned to help you choose the installation type and accessory for your application.Flow rate versus pipe diameter limits – up to 264 gal/min (60 m 3 /hr)Micro Motion Insertion Density and Viscosity Meter Accessories 5

Flow rate versus pipe diameter limits – 264 to 2640 gal/min (60 to 600 m 3 /hr)Installation guide selector – fork metersVelocity / flow rate limitsInstallation typeViscosity limit7826 (1)Density ±0.001g/cc7827 / 7828 / 7829Density ±0.001g/ccFlow-through chamber with 2˝ meter bore(1˝ or 2˝ pipeline)200 cP 1–10 gal/min (0.2–2.3 m 3 /hr) 1-10 gal/min (0.2–2.3 m 3 /hr)Flow-through chamber with 3˝ meter bore(2˝ or 3˝ pipeline)1000 cP 1–88 gal/min (0.2–19.9 m 3 /hr) 1-88 gal/min (0.2–19.9 m 3 /hr)Direct insertion/free-stream weldolet (2)20,000 cP

Ordering information – flow-through chambersModelProduct description782791 Flow-through chamber for 7826/7828 and 7827/7829 vibrating fork metersCode Inlet / Outlet Pipe size Flow Range Calibration BoundaryAvailable with all flow-through chamber connection to 782x optionsA 1-inch (25 mm) sch 80 5 - 40 l/min 2-inch Schd 40D 2-inch (50 mm) sch 80 5 - 40 l/min 2-inch Schd 40Available with flow-through chamber connection to 782x option N onlyB 1-inch (25 mm) sch 80 5 - 300 l/min 3-inch Schd 80E 2-inch (50 mm) sch 80 5 - 300 l/min 3-inch Schd 80G 3-inch (80 mm) sch 80 5 - 300 l/min 3-inch Schd 80Z ETO ETO refer to factoryCodeAZCodeBCCodeAB (1)C (1)G (1)H (1)NCodeABCGHJLNRTKMQSUPZMaterials316L Stainless SteelETOCertificationAvailable with all flow-through chamber connection to 782x optionsNoneAvailable with flow-through chamber connection to 782x option A & N onlyPED approvedFlow-through chamber connection to 782xAvailable with Inlet / Outlet Pipe Sizes A & D only2-inch ANSI 150RF Flanges2-inch ANSI 300RF Flanges - no certification2-inch ANSI 600RF Flanges - no certificationEN1092 RF DN50/PN40 - no certificationEN1092 RF DN50/PN100 - no certificationAvailable with all Inlet / Outlet Pipe Sizes1.5-inch Cone Seat Compression FittingProcess ConnectionsAvailable with all Inlet / Outlet Pipe Sizes A & B only1-inch ANSI 150RF Flanges1-inch ANSI 300RF Flanges1-inch ANSI 600RF FlangesEN1092 RF DN 25/PN40EN1092 RF DN 25/PN100Available with all Inlet / Outlet Pipe Sizes D & E only2-inch ANSI 150RF Flanges2-inch ANSI 300RF Flanges2-inch ANSI 600RF FlangesEN1092 RF DN 50/PN40EN1092 RF DN 50/PN100Available with all Inlet / Outlet Pipe Sizes G only3-inch ANSI 150RF Flanges3-inch ANSI 150RF Flanges3-inch ANSI 150RF FlangesEN1092 RF DN 80/PN40EN1092 RF DN 80/PN100Available with all Inlet / Outlet Pipe SizesWeld prepared endsETO Flange(1) Only available if Certification letter is ‘B’Micro Motion Insertion Density and Viscosity Meter Accessories 7

Ordering information – flow-through chambers continuedCode Temperature PortANoneBTemperature Port 1/2” NPT fittingCode Future OptionANoneCode TraceabilityANoneXCertificates of material traceabilityCode Factory OptionAStandardZETOTypical model number: 7827 91 DABCNAAAA8 Micro Motion Insertion Density and Viscosity Meter Accessories

Ordering information – pipeline weldoletsFree-stream weldoletsModel Product Description782781 Free-stream weldoletsCode MaterialA316L Stainless SteelZETO materialCode To Fit Main Pipeline DiametersA4-inch Schedule 40 Nominal BoreP6-inch Schedule 40 Nominal BoreB8-inch Schedule 40 Nominal BoreE10-inch Schedule 40 Nominal BoreZETO Nominal BoreCode TraceabilityANoneXCertificates of material traceabilityTypical model number: 782781 A A ARecessed weldoletsModel Product Description782782 Recessed weldoletsCode MaterialA316L Stainless SteelPCarbon Steel weldolet, Stainless Steel pocketZETO materialCode To Fit Main Pipeline DiametersA4-inch Schedule 40 Nominal BoreP6-inch Schedule 40 Nominal BoreB8-inch Schedule 40 Nominal BoreE10-inch Schedule 40 Nominal BoreZETO Nominal BoreCode Recession Depth (defined by pipe flow velocity)Afrom 1.6 fps to 9.8 fps (0.5 m/s to 3 m/s)Bfrom 6.6 fps to 13.1 fps (2 m/s to 4 m/s)Cfrom 9.8 fps to 16.4 fps (3 m/s to 5 m/s)Dfrom 13.1 fps to 19.7 fps (4 m/s to 6 m/s)ZETO DepthCode TraceabilityANoneXCertificates of material traceabilityTypical model number: 782782 A A A AMicro Motion Insertion Density and Viscosity Meter Accessories 9

Ordering information – blanking plugsModel Product Description782784 Accessories – blanking plugsCode SizeA1/2-inch Plug and FerruleB3/4-inch Plug and FerruleC1 1/2-inch Plug (no Ferrule required)Code MaterialA316L Stainless SteelZETO materialCode TraceabilityANoneXCertificates of material traceabilityTypical model number: 782784 A A A10 Micro Motion Insertion Density and Viscosity Meter Accessories

Micro Motion Insertion Density and Viscosity Meter Accessories 11