Series 911 E/F Emergency Eye Wash Valve

More documents

Recommendations

Info

DIMENSIONS: 1/2″ inlets & outletsValveNumber A B C911E/F 9″ 4″ 8″5040603070 80Testing the Mixing ValveA90110120130The mixing valve and the emergency fixtures it servesshould be test ed week ly for prop er op er a tion.Valve temperature test procedure is as follows:1. Activate eye wash fi xture to observe and recordthe tem per a ture of the dial thermometer. If thetem per a ture of the thermometer is not cor rect,readjust the mixing valve according to the sec tion“Set ting the Mixing Valve”.2. Observe the fl ow from the emergency fi xtures toensure an adequate fl ow of water.In addition to testing for proper temperature, the coldwater by-pass and hot water shut down fea tures ofthe mixing valve should be tested week ly.The test procedure is as follows:1. Test valve temperature as described in Step 1and Step 2 above.2. Shut off the hot water supply to the mixing valve.Observe the outlet fl ow from the emergency fi x-tures to ensure an ad e quate fl ow of cold wa ter.A slight drop in fl ow may occur after shuttingdown the hot water supply to the mixing valve;how ev er, the drop should be minimal and for ashort duration.3. Open the hot water supply to the mixing valve.The thermometer should return to the set tempera ture.4. Shut off the cold water supply to the mixing valve.The fl ow of water should shut down rapidly.BC(2)5. Open the cold water supply. The thermometershould return to the set tem per a ture.Note: The thermometer should be checked at leastevery six months.Replacing the Thermostat ElementThe thermostat re place ment procedure is as fol lows:1. Shut off the hot water supply and cold watersupply to the mix ing valve.2. Remove the four cover screws (#9) and removethe front cover (#26) of the valve.3. Remove thermostat (#11) from the valve body.No special tools are necessary.4. Insert a dowel rod, pencil (eraser-end), or narrowpen into the open end of the thermostat. Push onthe dowel rod with your hand. If the thermostatfeels spongy or springy, the thermostat has lostits charge. If the thermostat feels solid or hard,the thermostat is good and operable.5. Be sure that the stainless steel piston (#15)moves freely up and down within the liner (#21).Lime or calcium buildup should be cleaned withvin e gar, green scotch pad, or fi ne emery cloth.CAPACITY OF TYPE 911E/FTHERMOSTATIC MIXING VALVEFOR EMERGENCY SHOWERSPRESSURE DROP, POUNDS PER SQUARE INCH706050454035302520151/2″ MED10987651 2 3 4 5 6 7 8 9 10 15 20 30 35FLOW OF WATER, GALLONS PER MINUTENote: Gallon per minute ratings may vary dependingupon incoming water temperatures andpressures. Hot and cold water inlet pressuresmust be equal.Provisions shall be made to thermally isolatethe valve.
InstallationAfter installing the mixing valve, be sure to fl ush thesystem of debris. Lawler recommends isolation andcheck valves for proper maintenance.Typical Installation Figure 1When installed without a recirculation system:Install the valve as shown in Figure 1 with the mix ingvalve positioned below the hot water tank or heater.If this is not possible, pipe in heat trap as shown.Typical Installation Figure 2When installed with a recirculating pump on the hotwater supply line only:Note: If the valve is installed 20 feet or more fromthe wa ter heater, it is important to recirculate the hotwater supply to the mixing valve.Install the mixing valve as shown in Figure 2. Thenon-circulated loop should be limited to 10 feet andmust be fl ushed periodically.Caution: The cold water line must be installedso that it is not affected by excessively hot ambienttem per a tures. Provisions shall be madeto thermally isolate the valve. Cold water pipein stalled in the ceil ings of boil er rooms or roomsthat increase ambient temperature require a recirculatingpump.Figure 1Typical installation. Valve must beinstalled with check valves.WaterHeaterCWHeat Trap27″ DropHWStorageTankFigure 2Typical installation. Valve must beinstalled with check valves.Series 911E/F1 valve pereye wash fixtureEye/FaceWashNote: The mixing valve must be installed withinlet check valves and the Eyewash/Facewashfi x ture should be installed 4 to 10 feet fromthe mix ing valve.CWSeries 911E/FNote: The valve body must be maintained at anambient room temperature of above 50°F to preventpremature closure of the safety back-seatmech a nism.Heat Trap27″ DropMaximum Inlet Pressure: 125 PSI.Recommended Supply Pressure: 65 PSI.Recommended Inlet Temperature: 120°F.**When supplying 140°F or greater, additional outletcontrols should be used.We guarantee the Lawler Mixing Valve to be freefrom defects in workmanship and material, and,for a period of one year from date of purchase,will replace any parts found by Lawler Man u fac -tur ing Co., Inc. to be defective. We will not be heldGUARANTEE(3)WaterHeaterStorageTankRecirculating Pumpresponsible, how ev er, for any labor in ci den tal to,or for any dam ag es caused by, de fec tive ma te ri al.Each mix ing valve is thor ough ly in spect ed and testedunder ac tu al con di tions at our factory.
Page 1: 5330 East 25th StreetIndianapolis,

Series 911 E/F Emergency Eye Wash Valve

Create successful ePaper yourself

Delete template?

Save as template?