NEW KITS FO

SMD Flashing Name Plate KitThis exciting Chaney Electronics kit features your “Name in Lights”. Features space for up to 8letters or numbers of your choice (A-Z or 0-9) made up of brilliant Green SMD LEDs. Your name orsimple message can be seen from across the room even in full light conditions. The name flashesat your choice of speeds from slow to fast. Each character is about 1 5/8” tall and you can use all8 or just the quantity you need to make your name. We give you 150 special brilliant green SMDLEDs (enough to make most 8 character names). Size of name plate PC board is 2 1/4” x 9 1/2”. Tocause your name plate to flash, a small 2” x 1 5/16” control board that uses regular “feed thru” (notSMD) components is used. This IC circuit features a variable flash rate speed control and operatesfrom one 9V battery (not included). Complete with all parts, 2 PC boards and instructions. Sorry,no case available. Skill Level 3. Not for beginning students.SMD Flashing Name Plate Kit..................................................C6867 $30.25TOL (Temperature, Ohm, Light) KitOur Temperature, Ohm, Light (TOL) Kit makes a great introduction to programmable integrated circuits (PIC) by demonstrating 4specific functions being handled by a single pre-programmed PIC. This kit measures three different parameters and displays themon a 3.5” LCD. This kit uses a PIC16F88 pre-programmed IC to allow you to measure resistance from 30 ohms up to 470k ohms,temperature from 35ºF to 130ºF and light intensity from 0% up to 100% (full sunshine). The PC board is about 4.4” long x 1.6”wide and comes with the LCD display already soldered in (the pins on the display are very close together so we solder and testthe connections to prevent solder bridges). Operates on one 9V battery (not included) and uses a built in thermistor to measureambient temperature, a CDS cell to measure relative light intensity (when the light intensity drops below 10% a bright yellow LEDlights up). Finally, the kit uses clip leads that you can attach to resistors to display their values in ohms. Complete with all parts,pre-programmed PIC, PC board with display installed and instructions. Skill level 2. optional plastic Type 5 box C6367 $3.90TOL Kit..............................................................................................................C6996 $19.95Continuity Tester KitHandy kit is a must for anyone working with electronic circuits. Traces circuit paths for continuity, checksfor broken wires, shorted contacts, etc. Uses small piezoelectric speaker which emits a pleasant toneand features a bright red LED visual indication. Operates from one 9V battery (not included). Size ofboard: 2 1/4” square. Complete with all parts, PC board and instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40Continuity Tester Kit....................................................................................C6385 $3.95CMOS/TTL Logic Probe KitThe Chaney C6722 CMOS/TTL Logic Probe Kit is a handy, reliable, and inexpensive. Designed tooperate with voltages between 5 and 20 volts, this logic probe is the ideal tool for troubleshootingCMOS and TTL digital circuits. It has a visual indicator that consists of a red LED and a green LED.The red LED indicates a High (1) logic state, and the green LED indicates a Low (0) logic state.This logic probe is small, easy to build, and easy to use. Operates from the power of the circuit beingtested. Size of PC board: 3 5/8” x 1 1/4”. Complete with all parts, PC board and instructions.Skill Level 1.CMOS/TTL Logic Probe Kit......................................................C6722 $6.25Battery Tester KitOur Battery Tester Kit is just the answer to test all types of common batteries. Simple to use–justselect the battery voltage to be tested by rotating the selection switch and connect the clipleads to the battery. If the battery is good, the green LED lights. If it’s bad the red LED lights.Kit features 5 calibration trim pots to allow you to set up your tester to test any 5 different typebatteries that you frequently use. Size of board: 2.6” x 3.5”. Operates from one 9V battery(not included). Complete with all parts, PC board and instructions. Skill Level 1.optional plastic Type 5 box C6367 $3.90Battery Tester Kit........................................................................C6414 $9.25SMD TECHNOLOGYTEST EQUIPMENT KITS3 Slot AC Outlet Tester KitThis very useful tester checks outlets for 6 different faults or safety hazard conditions anddisplays the results. Uses bright “orange glow” neon lamps to indicate if ground is connectedor if hot and neutral are reversed, etc. Compact and very useful accessory for any tool box.Operates from 120VAC. Size of PC board 2” x 2”. Comes complete with a Type 1 clearplastic box that the student can drill or file a hole in (to allow the cord to go into box) andthen mount the completed board into. A supplied label completes the project and allowsyou to have a handy, ready to go tester that will check out any 120VAC outlet in the house.Complete with all parts. PC board, undrilled plastic box and instructions. Skill level 2 (sinceit operates on 120VAC).3 Slot AC Outlet Tester Kit........................................................C6842 $6.25Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 49