6 TroubleshootingType of malfunction Possible causes CorrectionPump does not move.Liquid does not dispense.7 Annex– Plug is not firmlyconnected.– The power switch is setto off.• Connect the plug firmly.• Switch on the unit.– Fuse is open. • Replace the fuse withnew one (1A).– Speed dial is set to 0. • Dial to accelerate speed.– Tube is not properly setin a groove.– Shape of rotor isimpressed on tube.– Tube is not specifiedfor the machine type.– Guide is not properlyset.– Guide support bolt isnot firmly tightened up.• Insert the tubeappropriately.• Reset tube and turn rotorwhile closing TubeGuide.• Use specified tube.• Set the guide properly.• Tighten the bolt upfirmly.7.1 XS 1 InterfaceControllerFootswitch1Start A1223456End ofCycle0 VDC3456S1217789Pot. 0 VDC+24 VDC89Connections on pin 3 and 4 have to be made seprately!14
7 Annex7.2 Accessories and Spare PartsPos. No. Description Type No. Order Code No.– Foot Switch (Replacement).............................................. 97201 88653– Standard Pump Head (Replacement)................................ 989401 841977– Manual Applicator Assembly (Replacement)................... 8901775 124444517 Applicator Tip Adapter Ø 1.7 mm ................................... 8901776 1244446Applicator Tip Adapter Ø 2.1 mm ................................... 8901777 1244447Applicator Tip Adapter Ø 2.6 mm ................................... 8901778 1244449Applicator Tip Adapter Ø 3.5 mm ................................... 8901779 124444818 Tubing, black, ID 2.4 x 0.4 mm (OD 3.2), 20 m .............. 8953001 1070735Tubing, clear, ID 2.4 x 0.4 mm (OD 3.2), 20 m ............... 8953182 1019162Tubing, black, ID 1.7 x 0.4 mm (OD 2.5), 20 m .............. 8953000 1070736Tubing, clear, ID 1.7 x 0.4 mm (OD 2.5), 20 m ............... 8953185 1109317Tubing, black, ID 1.4 x 0.3 mm (OD 2.0), 20 m .............. 8953184 1109318Tubing, clear, ID 1.4 x 0.3 mm (OD 2.0), 20 m ............... 8954866 1001830Tubing, black, ID 1.0 x 0.3 mm (OD 1.6), 20 m .............. 8953183 1109147Tubing, clear, ID 1.0 x 0.3 mm (OD 1.6), 20 m ............... 8953142 1087219– Needle Variety Kit ........................................................... 97262 218288– Syringe & Applicator Holder ........................................... 98501 756316– Silicon Grease 6g Tube .................................................... 997569 887227.3 Declaration of ConformityThe Manufactureraccording to the EC regulationsDeclaration of ConformityHenkel AG &Co. KgaAStandort MünchenGutenbergstr. 3D-85748 Garching b. Münchendeclares that the unit designated in the following is, as a result of its design and construction, in accordancewith the European regulations, harmonized standards and national standards listed below.Designation of the unit <strong>Benchtop</strong> <strong>Peristaltic</strong> <strong>Dispenser</strong> Type 98548Unit number 769914Applicable EC RegulationsEC Directive for Low Voltage 73/32/EEC. 93/68/EECEC Directive for Electro-Magnetic Compatibility89/336/EEC, including changes 91/263/EC, 92/31/EC and93/68/ECApplicable harmonized standardsEN 61010-1 :2001, EN 50081-2 :1993 (Class A),EN 61000-3-2 :2000, EN 6100-3-3 :1995,EN 6100-6-2 :1999Date/Manufacturer’s signature 08/20/2008 (Dr. W. Fleischmann)For changes to the unit that were not approved by Loctite, this declaration loses its validity.15