sinamics

Index 06/05
Power Connections .............................. 4-13
Connecting the Motor and Power Cables
...................................................... 4-15
Power Supply, Internal ......................... 4-19
Preparatory Steps
Mechanical Installation ....................... 3-5
PROFIBUS ........................................... 6-31
Bus Terminating Resistor ................. 6-32
Connection........................................ 6-31
Connectors........................................ 6-32
Ident Number .................................... 6-35
PROFIdrive NAMUR (option B04)........ 4-58
Protecting Power Components............. 9-34
Protection Functions............................. 9-34
PT100 Evaluation Unit (Option L86) .... 4-45
Q
Qualifications, Personnel Requirements 1-1
Qualified Personnel ................................ 1-1
Quality .................................................... 2-3
R
Ramp-Function Generator...................... 7-7
Reference model .................................. 7-26
Reforming the DC Link Capacitors..... 11-41
Relay Outputs....................................... 4-29
Removing the Interference Suppression
Capacitor........................................... 4-20
Replacement
Fault messages .............................. 11-42
Replacing
Control Interface Board, Type FX... 11-18
Control Interface Board, Type GX .. 11-20
Control Interface Board, Type HX .. 11-22
Control Interface Board, Type JX ... 11-24
Fan, Type FX .................................. 11-26
Fan, Type GX.................................. 11-28
Fan, Type HX.................................. 11-30
Fan, Type JX................................... 11-34
Filter Mats ......................................... 11-5
Power Block Type FX ....................... 11-6
Power Block Type GX....................... 11-8
Power Block Type HX..................... 11-10
Power Block Type JX...................... 11-14
Replacing Components ........................ 11-5
Replacing the Backup Battery of the
Cabinet Operator Panel .................. 11-39
Replacing the Cabinet Operator Panel11-39
Resetting Parameters........................... 5-42
Rotating Measurement ........................... 9-5
Runtime ................................................ 9-25
S
S5 – Selector for Voltage/Current AI0, AI14-
28
Safety, Definitions .................................. 1-1
Safety, Operating Instructions................ 1-3
Safety, Warning Information................... 1-1
Saving the Parameters, Permanently...6-63
Sensor Module SMC30 for Detecting the
Actual Motor Speed (Option K50) .....4-48
Separate 24 V DC Power Supply for
NAMUR (Option B02)........................4-57
Service ....................................................2-3
Service and Support ...........................10-12
Servicing ...............................................11-3
Setpoint Addition.....................................7-3
Setpoint Channel ....................................7-3
Setpoint sources
General................................................6-2
Setpoint Sources...................................6-27
Analog Inputs ....................................6-27
Fixed Speed Setpoints ......................6-30
Motorized Potentiometer ...................6-29
Setting the Language............................6-54
Setting the PROFIBUS Address ...........6-34
Signal Connections...............................4-23
Simulation operation .............................9-26
Sinusoidal Filter (Option L15) ...............4-31
Slip Compensation................................7-15
SMC30 ..................................................4-48
SMC30, Connection Examples.............4-53
Speed Controller...................................7-20
Speed controller adaptation..................7-27
Speed Controller Optimization................9-5
Speed controller pre-control .................7-23
Speed Limitation .....................................7-6
Stall Protection......................................9-38
Standstill Measurement ..........................9-4
STARTER ...............................................5-2
Commissioning....................................5-4
Configuring the Drive Unit .................5-11
Creating Your Project..........................5-4
Installation ...........................................5-2
Project Wizard.....................................5-6
Settings for cabinet units with a high
power rating...................................5-28
Starting the Drive Project ..................5-29
User Interface......................................5-3
Status word 1 ...............................6-41, 6-42
Storage ...................................................3-3
Suppression Speed.................................7-5
Switching Between Clockwise and Counter-
Clockwise Rotation............................6-57
T
Technical Data ......................................12-8
Technologieregler .................................9-27
Telegram Selection, User-Defined........6-36
Telegrams and Process Data ...............6-35
Temperature Sensor.............................4-28
Thermal Monitoring...............................9-35
Thermal Motor Protection .....................9-39
Index-4
SINAMICS G150
Operating Instructions