2009 - 2010

New
B1000.2STA, B1000.3STA, B1145.3STA
Aluminum Combinations
These self-tailing winches raise and trim sails on the largest yachts. They
are available in 2 or 3 speeds, and come in marine-grade aluminum, or with
aluminum base, stainless drum, and aluminum top combinations to maximize
durability and corrosion resistance. Load-carrying gears are 17-4PH stainless
steel. Self-tailing jaws accept a wide range of line sizes.
Modern-style winches integrate the stripper support arm into the self-tailing
jaw assembly for a clean, smooth look. Classic winches are traditionally
styled with a one-piece stripper arm that attaches to the top of the winch,
encompassing the self-tailing jaws.
Winches have power ratios of up to 100:1 and are often used with either
hydraulic or electric drives. The 3-speed 1140ST features a backwind to
ease the loads on the winch before the sheet is released.
Hanuman (Endeavour II) — On Deck photo
B990.2STA
B990.3STA
Modern Self-Tailing
B1145.3STA
B990, B1130 and B1145 are available
in grey-anodized aluminum by special
order. Contact Harken Italy.
B1150STASA
Classic Self-Tailing
B1120STASA
B1000.2STA
B1000.3STA
Ø
Line entry Fastener
Part Drum (D) Base (B) Height (H) Weight height (LE) circle Fasteners Gear ratio Power ratio
No. in mm in mm in mm lb kg in mm in mm in mm 1 2 3 1 2 3
Classic Self-Tailing
B1000.2STA 6 7 /8 175 11 5 /16 287 13 3 /16 335 46.8 21.2 6 7 /16 164 9 3 /16 233 8 x 3 /8 SH/HH 8 x 10 SH/HH 9.40 28.10 — 32.10 93.00 —
B1000.3STA 6 7 /8 175 11 5 /16 287 13 3 /16 335 50.1 22.7 6 7 /16 164 9 3 /16 233 8 x 3 /8 SH/HH 8 x 10 SH/HH 2.23 9.40 28.10 6.50 32.10 93.00
B1120STASA 11 13 /16 300 16 15 /32 418 14 9 /16 370 127.8 58 6 13 /32 163 14 3 /8 365 12 x 3 /8 SH 12 x 10 SH 2.0 11.4 33.3 3.4 19.3 56.3
B1140STASA 14 3 /16 360 22 1 /8 562 18 3 /16 462 299.9 136 8 11 /32 212 18 1 /8 460 8 x 1 /2 SH 8 x 12 SH 2.9 11.6 42.6 4.0 16.4 60.1
B1150STASA 16 5 /32 410 25 3 /16 640 19 3 /4 502 485 220 8 27 /32 225 22 1 /16 560 12 x 1 /2 SH 12 x 12 SH 3.4 15.3 64.9 4.2 19 80.4
Modern Self-Tailing
B990.2ST* 8 203 11 1 /32 280 11 9 /16 294 43.2 19.6 5 31 /32 151.7 9 3 /16 233 8 x 3 /8 SH 8 x 10 SH 9.9 40.0 — 24.8 100 —
B990.3ST* 8 203 11 1 /32 280 11 9 /16 294 43.2 19.6 5 31 /32 151.7 9 3 /16 233 8 x 3 /8 SH 8 x 10 SH 1.0 9.9 40.0 2.5 24.8 100
B1110STASA 10 31 /32 279 13 11 /32 339 9 3 /4 246.5 — — 3 1 /2 89 10 23 /32 272 8 x 3 /8 SH 8 x 10 SH 1.0 9.43 43.6 1.8 17.2 79.4
B1130.3ST* 12 3 /4 324 16 3 /32 409 12 1 /8 308 86.0 39.0 4 17 /32 115 12 3 /4 324 9 x 1 /2 SH 9 x 12 SH 1.0 10.8 55.2 1.6 16.9 86.6
B1135.3STASA 12 3 /4 324 16 5 /32 410 12 1 /8 308 220.5 100 4 11 /32 110 12 3 /4 324 9 x 1 /2 SH 9 x 12 SH 1.1 10.8 55.2 1.6 16.9 86.5
B1145.3ST* 14 1 /4 362 21 3 /16 538 16 1 /2 419 192.9 87.5 8 3 /16 208 17 3 /4 450 14 x 1 /2 SH 14 x 12 SH 2.9 11.9 53.6 4.1 16.6 75.6
*Available in black-anodized or grey-anodized aluminum. For black add A to part number. For grey-anodized add GGG