Separator Bible

Recommendations

Info

Victor Marine Limited Eurocourt Cosgrove Road West Thurrock, United Kingdom Vat Reg. no. GB133212520 Tel: +44 (0)1708 899780 Fax: +44 (0)1708 890599 Web: www.victormarine.com For Aluminium Shells For aluminium, same specification but would suggest a thorough mechanical abrade or sweep blasting with non metallic aggregate to achieve a profile. Standard finish colour topcoat BS5252 00A13 (Storm Grey - International K724) or specified by customer. Please refer to individual paint data sheets for application procedures and act accordingly. Issue: 02 21.10.2015
Product Description WHITE INTERNAL Interseal ® 670HS A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. Available in an aluminium pigmented version to provide additional anti-corrosive barrier protection. Surface Tolerant Epoxy Intended Uses For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and paper plants, bridges and offshore environments in both atmospheric exposure and immersion service. NSF Certification is for tanks greater than 100 gallons (378.5 litres). Certified to NSF/ANSI 61 Practical Information for Interseal 670HS Colour Gloss Level Volume Solids Range Semi-gloss (Aluminium is eggshell) 82% ± 3% (depends on colour) Typical Thickness 100-250 microns (4-10 mils) dry equivalent to 122-305 microns (4.9-12.2 mils) wet Theoretical Coverage Practical Coverage Method of Application Drying Time 6.56 m 2 /litre at 125 microns d.f.t and stated volume solids 263 sq.ft/US gallon at 5 mils d.f.t and stated volume solids Allow appropriate loss factors Airless spray, Air spray, Brush, Roller Overcoating Interval Interseal 670HS with Self Overcoating Interval with recommended topcoats Temperature Touch Dry Hard Dry Min Max Max † Min Max Max †# 10ºC (50ºF) 8 hours 32 hours 32 hours 6 weeks Extended* 20 hours 21 days 12 weeks 15ºC (59ºF) 7 hours 26 hours 26 hours 4 weeks Extended* 14 hours 14 days 8 weeks 25ºC (77ºF) 5 hours 18 hours 18 hours 14 days Extended* 10 hours 7 days 4 weeks 40ºC (104ºF) 2 hours 6 hours 6 hours 7 days Extended* 4 hours 3 days 2 weeks For curing at low temperatures, an alternative curing agent is available. See Product Characteristics for details. Refers to situations where immersion is likely to occur † Refer to atmospheric service only * See International Protective Coatings Definitions & Abbreviations # Maximum overcoating intervals are shorter when using polysiloxane topcoats. Consult International Protective Coatings for further details. Regulatory Data Flash Point (Typical) Base (Part A) 36°C (97°F) Curing Agent (Part B) 56°C (133°F) Mixed 33°C (91°F) Product Weight 1.6 kg/l (13.3 lb/gal) VOC 114 g/kg EU Solvent Emissions Directive (Council Directive 1999/13/EC) 2.00 lb/gal (240 g/lt) EPA Method 24 Protective Coatings Page 1 of 4 Issue Date:11/10/2012 Ref:2394 Worldwide Product
Page 1 and 2: Separator Bible Effective: 09th Nov
Page 3: Unit 1 St Elizabeth Park, Grey Stre
Page 7 and 8: Pressure Relief Valves Separator PR
Page 9 and 10: CS1000 & CS2000 SHEET 1 OF 1 A B C
Page 11 and 12: Victor Marine Limited Eurocourt Cos
Page 13 and 14: DRY RUN CONVERSION FITTING PROCEDUR
Page 15: Motor Wiring MOTOR TERMINAL 3 TO PA
Page 19 and 20: L2 2 T1 4 T2 6 T3 E 1 2 3 E 4 5 6 E
Page 21 and 22: Figure 3 Right Hand Side Vessel Int
Page 25 and 26: Each equation is quoted by some sou
Page 51: Victor Marine Limited Eurocourt Cos
Page 55 and 56: Interseal ® 670HS Surface Tolerant
Page 57 and 58: PRODUCT DESCRIPTION EXTERIOR PRIMER
Page 59 and 60: PRODUCT CHARACTERISTICS Intergard
Page 61 and 62: BLUE EXTERIOR Interthane 990 Polyur
Page 63 and 64: Interthane 990 Polyurethane Finish

Separator Bible

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?