Cole-Hersee - D-275-MasterCatalog

More documents

Recommendations

Info

J J4 battery-related products BATTERY ISOLATORS For vehicles with two batteries, these devices electrically isolate the batteries to prevent the battery with the higher charge from draining into that with the lower charge. In addition, both batteries can be charged simultaneously from one source. Use general purpose Battery Isolators for 12-36V DC negative ground systems (48051 is for 12V DC only). The electronic components are embedded to give excellent protection from adverse conditions, such as contamination and vibration. The integral heat sink provides efficient heat dissipation. The amp rating of each item is the maximum alternator rating. For wiring instructions, see page 96. Most alternators on new vehicles have an integral electronic voltage regulator that requires the use of the 4-stud battery isolator. The small 4th stud is for connection to a circuit switched by the ignition switch. The newer alternators were first introduced by Delco and are therefore sometimes called ‘Delcotron-type alternators’. A 4-stud battery isolator can be used with older pattern alternators (in this case the 4th stud will remain unconnected), but a 3-stud battery isolator cannot be used with the Delcotron-type alternator. Battery isolators also have a ‘per leg’ rating which indicates the maximum current it can deliver to either battery. All Cole Hersee battery isolators have a per leg rating equal to half the alternator rating. Thus a 48092 with a rating of 90A has a per leg rating of 45A per leg. Smart Battery Isolators 4-Stud Battery Isolators For use with Delcotron-type alternators. 48092 90 Amp 90A at 12V DC, 12-36V. Terminations: three 1/4" (6.4mm) studs and one No. 10 stud. Two 9/32" (7.2mm) diameter mounting holes. Size: 6 1/2"L x 3 1/4"W x 2 13/16"H (165.0 x 82.6 x 71.0mm). 48525 85A at 12V DC 48530 200A at 12V DC Prevents loads on auxiliary battery from draining the starting battery, a Smart Isolator is more flexible than traditional Battery Isolators: • It works with all types of alternator. • Smaller and lighter than traditional isolators. • There are no efficiency losses due to diodes. • It allows bi-directional charging from the alternator or from shore power. • It reduces the load on the charging system by not connecting the auxiliary battery until the primary battery is charged to 13.2V. This extends the life of expensive charging components. Simple to install – connect to starting battery, auxiliary battery and ground. Optional start assist: momentary switch allows the auxiliary battery to assist the starting battery. LED status indicator. Specifications Operating temperature range: -40 to 85ºC. Ingress protection: IP66 per IEC, (high pressure wash resistant). Humidity: to 90% RH. Vibration: 10-500Hz per SAE J1455. Shock & thermal shock: per SAE J1455. EMI/RF: Per SAE J1455 & J1113. Battery terminals torque: 50 in-lbs (5.78Nm). Normal input voltage: 9V min, 16V max. Continuous current: 48525 85A; 49530 200A. Connect voltage: 13.2V typical after two minutes at this level. Disconnect voltage: 12.7V after one minute at this level. Quiescent current: 5mA typical, 8mA max. Relay off, start signal input open or grounded. 48122 140 Amp 140A at 12V DC, 12-36V. Terminations: three 5/16" (7.9mm) studs and one No.10 stud. Four 9/32" (7.2mm) diameter mounting holes. Size: 6"L x 4 13/16"W x 3 11/32"H (152.4 x122.2 x 84.9mm). 48162 200 Amp 200A at 12V DC, 12-36V. Terminations: three 5/16" (7.9mm) studs and one No.10 stud. Four 9/32" (7.2mm) diameter mounting holes. Size: 8 1/2"L x 4 3/16"W x 3 13/32"H (215.0 x 122.2 x 86.5mm). Rapid ship item. BP Available in retail clamshell pack. Minimum order quantity may apply. Part numbers needed in BOX require a -BX suffix on the purchase order. Cole Hersee Co. 20 Old Colony Ave, Boston, MA 02127-2467 92 T 617.268.2100 F 617.268.9490 www.colehersee.com
J4 battery-related products BATTERY ISOLATORS J 3-Stud Battery Isolators For use with alternators that do not have an integral electronic voltage regulator. 48080 42 Amp 42A at 12V DC, 12-36V. Terminations: one 10AWG 6" (152.4mm) wire lead, two 12AWG wire leads. Two 13/64" (5.2mm) diameter mounting holes. Size: 5"L x 3 1/4"W x 2 3/16"H (127.0 x 82.6 x 71.0mm). 48160 200 Amp 200A at 12V DC, 12-36V. Terminations: three 5/16" (7.9mm) studs. Four 9/32" (7.2mm) diameter mounting holes. Size: 8 1/2"L x 4 3/16"W x 3 13/32"H (215.0 x 122.2 x 86.5mm). 48070 70 Amp 70A at 12V DC, 12-36V. Terminations: three 1/4" (6.4mm) studs. Two 9/32" (7.2mm) diameter mounting holes. Size: 5"L x 3 1/4"W x 2 3/16"H (127.0 x 82.6 x 71.0mm). For Ambulances Used to isolate medical equipment batteries from vehicle batteries. With Schottky diode, to comply with Federal Specification KKK-A-1822B for ambulances. 48051 75 Amp at 12V DC 48090 90 Amp 90A at 12V DC, 12-36V. Terminations: three 1/4" (6.4mm) studs. Two 9/32" (7.2mm) diameter mounting holes. Size: 6 1/4"L x 3 1/4"W x 2 3/16"H (165.0 x 82.6 x 71.0mm). 48161 250 Amp 250A at 12V DC, 12-36V. Same as 48160, but with Schottky diodes. Terminations: three 5/16" (7.9mm) studs. Four 9/32" (7.2mm) diameter mounting holes. Size: 8 1/2"L x 4 3/16"W x 3 13/32"H (215.0 x 122.2 x 86.5mm). 48120 140 Amp 140A at 12V DC, 12-36V. Terminations: three 5/16" (7.9mm) studs. Four 9/32" (7.2mm) diameter mounting holes. Size: 6 1/4"L x 4 3/16"W x 3 11/32"H (152.4 x 122.2 x 84.9mm). Ignition See Section C. Rapid ship item. BP Available in retail clamshell pack. Minimum order quantity may apply. Part numbers needed in BOX require a -BX suffix on the purchase order. Cole Hersee Co. 20 Old Colony Ave, Boston, MA 02127-2467 93 T 617.268.2100 F 617.268.9490 www.colehersee.com
Page 2 and 3:
index 3-digit numbers 407-01 ......
Page 4 and 5:
INDEX Part Number Section Page Part
Page 6 and 7:
Keyword INDEX Keyword Page Keyword
Page 8 and 9:
A A1 rocker switches WEATHER-RESIST
Page 10 and 11:
A A1 rocker switches WEATHER-RESIST
Page 12 and 13:
A A2 rocker switches MILLIAMP ROCKE
Page 14 and 15:
A A4 rocker switches STANDARD SERIE
Page 16 and 17:
A A5 rocker switches NARROW BODY SW
Page 18 and 19:
A A8 rocker switches ACCESSORIES Ro
Page 20 and 21:
A A9 rocker switches WIRING DIAGRAM
Page 22 and 23:
B B1 toggle switches 54100 SERIES 5
Page 24 and 25:
B B4 toggle switches FREIGHTLINER R
Page 26 and 27:
B B5 toggle switches HEAVY DUTY 25A
Page 28 and 29:
B B6 toggle switches ON -OFF Down:
Page 30 and 31:
B B8 toggle switches SPECIALIZED AP
Page 32 and 33:
B B9 toggle switches ACCESSORIES Sw
Page 34 and 35:
B B10 toggle switches INFORMATION S
Page 36 and 37:
C ignition switches C2 956 SERIES S
Page 38 and 39:
C C3 ignition switches UNIVERSAL ST
Page 40 and 41:
C C3 ignition switches UNIVERSAL ST
Page 42 and 43:
C C4 ignition switches MARINE SWITC
Page 44 and 45:
C C5 ignition switches SPECIALIZED
Page 46 and 47:
C C5 ignition switches SPECIALIZED
Page 48 and 49: C C7 ignition switches INFORMATION
Page 50 and 51: 1 D D1 On A-B On A-C 9 6 Off rotary
Page 52 and 53: D D3 rotary & headlamp switches ROT
Page 54 and 55: D D5 rotary & headlamp switches PUS
Page 56 and 57: D D6 rotary & headlamp switches ELE
Page 58 and 59: D D7 rotary & headlamp switches FOO
Page 60 and 61: E E1 wiper switches ELECTRONIC SWIT
Page 62 and 63: F F1 push-pull switches ONE CIRCUIT
Page 64 and 65: F F4 push-pull switches SPECIAL APP
Page 66 and 67: G G1 momentary switches NORMALLY OF
Page 68 and 69: G G3 momentary switches TWO CIRCUIT
Page 70 and 71: G G5 momentary switches SPECIAL MOM
Page 72 and 73: G G5 momentary switches SPECIAL MOM
Page 74 and 75: G G7 momentary switches DOOR MOMENT
Page 76 and 77: G G7 momentary switches DOOR MOMENT
Page 78 and 79: H H1 solenoids & relays STEEL & PHE
Page 80 and 81: H H1 solenoids & relays STEEL & PHE
Page 82 and 83: H H2 solenoids & relays PVC COATED
Page 84 and 85: H H3 solenoids & relays PLASTIC BOD
Page 86 and 87: H H5 solenoids & relays RELAYS Heav
Page 88 and 89: H H5 solenoids & relays RELAYS Micr
Page 90 and 91: H notes For orders or questions ple
Page 92 and 93: J J1 battery-related products LOW V
Page 94 and 95: J J2 battery-related products MASTE
Page 96 and 97: J J1 J2 battery-related products MA
Page 100 and 101: J J5 battery-related products ACCES
Page 102 and 103: J J6 battery-related products INFOR
Page 104 and 105: K K1 electronic devices LOW VOLTAGE
Page 106 and 107: K K2 electronic devices MODULES Ele
Page 108 and 109: K K2 electronic devices MODULES 480
Page 110 and 111: L L2 stoplamp switches MECHANICAL S
Page 112 and 113: M M2 monitoring devices OIL PRESSUR
Page 114 and 115: M monitoring devices M3 MISCELLANEO
Page 116 and 117: N N1 warning devices, pilot lights,
Page 122 and 123: N warning devices, pilot lights, pa
Page 126 and 127: N notes For orders or questions ple
Page 128 and 129: P P1 circuit protection & wiring CI
Page 130 and 131: P P1 circuit protection & wiring CI
Page 132 and 133: P P2 circuit protection & wiring BL
Page 134 and 135: P P3 circuit protection & wiring TE
Page 136 and 137: P P4 circuit protection & wiring FU
Page 138 and 139: P P4 circuit protection & wiring FU
Page 140 and 141: P P5 circuit protection & wiring CL
Page 142 and 143: P P6 circuit protection & wiring AC
Page 144 and 145: Q Q1 electrical connectors TRACTOR-
Page 146 and 147: Q Q1 electrical connectors TRACTOR-
Page 148 and 149:
Q Q2 electrical connectors 1-TO 6-P
Page 150 and 151:
Q Q4 electrical connectors AUTOMOTI
Page 152 and 153:
Q Q4 electrical connectors AUTOMOTI
Page 154 and 155:
Q Q6 electrical connectors ACCESSOR
Page 156 and 157:
Q Q7 electrical connectors INFORMAT
Page 158 and 159:
R R1 special purpose switches MECHA
Page 160 and 161:
R R3 special purpose switches OVERD
Page 162 and 163:
notes For orders or questions pleas
Page 164 and 165:
S S1 knobs & nuts STANDARD KNOBS 81
Page 166 and 167:
S S2 knobs & nuts FACENUTS & HEXNUT
Page 168 and 169:
T T2 displays & literature DISPLAY
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
what’s new? LED Rocker Switches A
Page 178 and 179:
table of contents A ROCKER SWITCHES
show all

Cole-Hersee - D-275-MasterCatalog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?