NTN - Cylindrical and Tapered Roller Bearings

More documents

Recommendations

Info

Bearing Selection Bearing Types NON-SEPARABLE BEARINGS Design Features • Two split retaining rings in outer ring. • Two ribbed inner ring. • One-piece steel cage. Application • Used where bearing must be assembled as a unit and where design has no provision to retain outer ring axially. • Will not accomodate thrust loads or locate shaft. MU----TV Same design features and applications as MU—TV above, except outer ring contains one split retaining ring and one solid rib which will take moderate thrust loads or locate shaft in one direction. MU----UV Design Features • Two split retaining rings in outer ring. • Two ribbed inner ring. • No cage (full complement of rollers). Application • Use is similar to MU—TV above. • Cage is omitted and rollers are added for increased radial load capacity. Permissible bearing speed, however, is less than the caged type bearing. MU----TM Same design features and application as MU—TM above except outer ring contains one split retaining ring and one solid rib that will take a moderate thrust load or locate shaft in one direction. MU----UM 35
Cylindrical Roller Bearings Interchange Charts for Basic Series* SEPARABLE INNER RING TYPE BEARINGS BOWER AFBMA FAG HYATT LINK BELT ROLL WAY SKF NTN MA----TV --RM-- A----TS MA----TV E----B HNU---A MA----EL --RU-- NU--- A----WB MA----EX E----U NU-- MR----TV --RR-- R----TS MR----TV L----B HNJ---A MR----EL --RJ-- NJ-- R----WB MR----EX L----U NJ-- MR----UV --RS-- R----YS MR----UV L----J MSN----EL --RT-- NUP--- JRN----WB MSN----EX LP----U NUP-- SEPARABLE OUTER RING TYPE BEARINGS BOWER AFBMA FAG HYATT LINK BELT ROLL WAY SKF NTN MU----DL --RF-- NF--- BU----L MU----DX U----L NF-- MU----CL --RN-- N--- BU----Z MU----CX U----E N-- MU----SNL --RP-- BU----LNJ MU----SNX U----LP NP-- MU----DV --RF-- NF-- BU----L MU----DX U----L NF-- MU----CV --RN-- N--- BU----Z MU----CX U----E N-- MU----SNV --RP-- BU----LNJ MU----SNX U---LP NP-- NON-SEPARABLE TYPE BEARINGS BOWER AFBMA FAG HYATT LINK BELT ROLL WAY SKF NTN MU----TV --RK-- U----TS MU----TV U----B HNC---A MU----TM --RK--V U----TM MU----TM UM----B HNC---AV NV-- MU----UV --RY-- U----YS MU----UV U----J MU----UM --RY-V U----YM MU----UM UM----J * Charted bearings interchange for boundary dimensions (I.D., O.D., width) and bearing types. They may not interchange due to differences in load ratings or cage styles. 36
Page 1 and 2: CylindriCal and Tapered roller Bear
Page 4 and 5: Table of Contents INTRODUCTION. . .
Page 6 and 7: Table of Contents TAPERED ROLLER BE
Page 8 and 9: Introduction Cylindrical Roller Bea
Page 10 and 11: Engineering Section Glossary of Sym
Page 12 and 13: Engineering Section BEARING LOAD RA
Page 14 and 15: Engineering Section Tangential Comp
Page 16 and 17: Engineering Section An Imbalance Fo
Page 18 and 19: Engineering Section SPECIAL CASES V
Page 20 and 21: Engineering Section The These value
Page 22 and 23: Engineering Section lubrication the
Page 24 and 25: Engineering Section a 3 —Lubricat
Page 26 and 27: Engineering Section LIMITING SPEEDS
Page 28 and 29: Engineering Section LUBRICATION The
Page 30 and 31: Engineering Section Grease GREASE G
Page 32 and 33: Introduction Cylindrical Roller Bea
Page 34 and 35: Introduction Bearing CAGES “M”
Page 36 and 37: Bearing Selection STANDARD SERIES M
Page 38 and 39: Bearing Selection Bearing Types SEP
Page 40 and 41: Bearing Selection Bearing Types SEP
Page 44 and 45: Dimensions and Ratings r Wr r r R R
Page 46 and 47: Dimensions and Ratings r r H A C F
Page 70 and 71: Dimensions and Ratings W MAX-PAK (M
Page 80 and 81: Dimensions and Ratings C W MOJ & MO
Page 82 and 83: Dimensions and Ratings Custom “R
Page 84 and 85: Dimensions and Ratings “R” Seri
Page 86 and 87: Dimensions and Ratings Mast and Cha
Page 88 and 89: Dimensions and Ratings Rotational o
Page 90 and 91: Dimensions and Ratings Outer Ring G
Page 92 and 93:
Dimensions and Ratings Internal Dia
Page 94 and 95:
Dimensions and Ratings Internal Dia
Page 96 and 97:
Mounting and Fitting Practice Gener
Page 98 and 99:
Mounting and Fitting Practice Inner
Page 100 and 101:
Mounting and Fitting Practice Inner
Page 102 and 103:
Mounting and Fitting Practice 1900
Page 104 and 105:
Mounting and Fitting Practice Outer
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Mounting and Fitting Practice Shaft
Page 112 and 113:
Mounting and Fitting Practice Housi
Page 114 and 115:
Introduction Tapered Roller Bearing
Page 116 and 117:
Introduction Bearing Design True Ro
Page 118 and 119:
Bearing Selection by Bore Size Bear
Page 120 and 121:
Bearing Selection by Bore Size Bear
Page 122 and 123:
Dimensions and Ratings W W W o W o
Page 124 and 125:
Dimensions and Ratings Load Rating:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Dimensions and Ratings T W f D f W
Page 182 and 183:
Dimensions and Ratings W p W p W i
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Dimensions and Ratings Bore Diamete
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Tolerances Tolerances for Metric Sy
Page 208:
Fitting Practice Tables Cone Fittin
show all

NTN - Cylindrical and Tapered Roller Bearings

Create successful ePaper yourself

Delete template?

Save as template?