Building Automation Controls Catalog 2006 - Trane

TEMPERATURE
28
TEMPERATURE
KELE ROOM TEMPERATURE SENSOR, THERMISTOR AND RTD
KTR * SERIES
MOUNTING AND SENSOR ONLY WIRING
Toggle bolts or other direct wall-mount screws can be used where
back box is not required. Adapters are not required when mounting
directly to electrical outlet boxes.
Basic model comes with screw terminal block, white decorator faceplate,
two #6-32 screws for handibox-mounting, and two #6 x 1" screws
for direct wall-mounting. Locking cover screws are #6-32 with a 1/16"
Allen key head, installed as needed.
Wire Access
Hole
Mounting Back Plate
Mounting
Screws
Option Board Clip
Self-Latching
Cover
Cover
Locking
1/16" Allen Screws
Installed as needed
To BAS
Controller
The sensor should be mounted approximately 5' (1.5m) above the floor,
on an interior wall, out of the sun, and away from any heating or cooling
generating devices.
Note: Adjust option requires option board removal to mount back plate.
2
1
JP1
Push button will short out the
pot or sensor momentarily
LED
Axxx Pot to BAS Controller
TB4 for MB only
JP2
Pot Action
Communication Wiring
J1 or J2
C
MB
Button Jumper
8 1-2 Pot
7 3-4 Pot
5-6 Sensor
7-8 Sensor
Customer Contact
24V (AC/DC)
Sensor to BAS Controller
Sensor
DA RA
Shipped DA
Left to right
Low to high resistance
ORDERING INFORMATION
MODEL DESCRIPTION
KTR Kele room sensor housing
SENSOR SELECTION
3 10,000Ω thermistor @ 77°F (25°C), Type III material
21 2252Ω thermistor @ 77°F (25°C), Type II material
22 3000Ω thermistor @ 77°F (25°C), Type II material
24 10,000Ω thermistor @ 77°F (25°C), Type II material
27 100,000Ω thermistor @ 77°F (25°C), Type II material
42 20,000Ω thermistor @ 77°F (25°C), Type II material
81 100Ω RTD, 385 platinum curve
85 1000Ω RTD, 385 platinum curve
91 1000Ω RTD, 375 platinum curve
ROOM SENSOR OPTIONS (Options to be listed alphabetically with dashes)
A400 Setpoint adjust with 400Ω span (R5 for offset), Patone 431C
A10K Setpoint adjust with 10,000Ω span (R5 for offset), Patone 431C
A20K Setpoint adjust with 20,000Ω span (R5 for offset), Patone 431C
A100K Setpoint adjust with 100,000Ω span (R5 for offset), Patone 431C
CL1 Custom logo option one color, (CL2 = two color, CL3 = three color)
J1 RJ11 externally-accessible communication jack (CCRJ11AD)
J2 RJ11 internal communication jack
LED LED lamp indicator, standard 24 VAC/VDC voltage
MB Momentary pushbutton switch, jumpered across sensor or pot (JP1)
N1 NIST certificate, one reference point 32°F (0°C)
N2 NIST certificate, two reference points 32°/158°F (0°/70°C)
TB4 Separate termination for MB option
WIRING TYPICAL COVER OPTIONS
RELATED PRODUCTS
10-531 Wall adapter plate 7" x 5.25"
RJ11 plug
SW3
RT1
IN JP1
1
+
-
-
OUT
+
J3
POT
J4
R4
R5
R2
-
LED
+
2
1
J1
SENSOR
JP2
R6
K
R3
A
K
D2
MB
Button
A
8
7
8
7
D3
RJ11 plug with cover off;
for J2 option
SW2
Axxx
6
LED
1
J2
J7
SW1 SW4
SETPOINT ADJUST
COVER ON
CCRJ11AD accessory;
required for J1 option
DA Low to high resistance
RA High to low resistance
Sample Order
KTR3 Kele room sensor
with 10K Type III thermistor
KTR85-A400-MB Kele room sensor
with 1000Ω 385 RTD
with 400Ω adjust pot
and momentary switch
KTR24-N1-LED Kele room sensor
with 10K Type II thermistor
with NIST and LED lamp
Accessories
CCRJ11AD J1 option adaptor
KT-1 Cover mouting screwdriver
1/16" Allen/standard/philips
Logo Color Chart
Pantone 485
Pantone 356
Pantone 492C
Pantone 124C
Pantone 300
Pantone 431C
Pantone 299
Pantone 6C
Other Pantone colors available upon request.
RT2