You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Customer : ENV<br />
Type : A<strong>320</strong><br />
Rev. Date : Nov 01, 2016<br />
<strong>51</strong>-<strong>21</strong>-<strong>11</strong> Application of Protective Treatment to Metal Parts<br />
Manual : <strong>SRM</strong><br />
Selected effectivity :<br />
- Apply passivating solution (Item <strong>11</strong>) with a brush or swab to the plated surface. Allow<br />
the solution to remain in until a yellow or gold appearance is obtained.<br />
- Rinse the area with clean cold running water.<br />
- Dry the repair area with an air blast or with a hot air dryer at a maximum temperature<br />
of 50° C (122° F) or gently dab the surface with soft clean tissues, absorbent paper or<br />
clean cotton wool.<br />
- Inspect the treated areas as described in 2.B.(1).(e).5.e Paragraph 4.<br />
NOTE: Make sure that the required paint coatings are applied within 16 hours.<br />
NOTE: Do not return used solutions in original containers. The solutions, rinsing water<br />
and used bonnets must be processed or destroyed by an approved organization.<br />
Contaminated packaging if not re-used with the same product is also special<br />
waste to be sent to an approved organization for recycling or disposal.<br />
(f)<br />
Cadmium brush plating (or pad cadmium plating DALIC process) for stainless steels with<br />
maximum tensile strength of <strong>11</strong>00 N/mm² (159 KSI).<br />
NOTE: This process must be carried out by trained and approved personnel. An operator training<br />
service is available from the solution suppliers.<br />
1 Equipment<br />
- Power supply: variable rectifier minimum fitted with voltmeter, ammeter, ampere-hour<br />
meter, reversing switch and on/off switch.<br />
- Dishes for solutions glass polyethylene or porcelain flat bottom dishes of convenient size.<br />
- Electrodes: Use DALIC, DALIC UK or SIFCO tampons which have to be prepared in<br />
accordance with the material manufacturer's instructions. For optimum deposit speed area<br />
and shape of the anode must be determined by the area and the shape of the part to be<br />
plated. The size should be s/6 < S < s/3 where "s" is the area to be treated and "S" the<br />
area of the anode.<br />
- Hot air dryer (oil free).<br />
2 Repair Materials<br />
ITEM NOMENCLATURE QTY MATERIAL/REMARKS<br />
1 Cleaning Agent AR Material No. <strong>11</strong>-003 or <strong>11</strong>-026 (Refer to<br />
CML)<br />
2 Lint free cloth, cotton wool AR Local Purchase<br />
3 Abrasive Paper - Silicon Carbide<br />
(grade 120)<br />
4 Abrasive Paper - Aluminum Oxide<br />
AR Local Purchase<br />
(grade <strong>320</strong> - water resistant)<br />
or finer or red SCOTCH-BRITE<br />
pads<br />
5 Masking Tape AR PVC insulating tape or 3M No. 470 or aluminum<br />
tape Material No. 08-052 (Refer to<br />
CML)<br />
6 Brush or Swab AR Local Purchase<br />
7 De-mineralized Water AR<br />
8 Aluminium Oxide Powder (80 microns)<br />
AR DALIC Reference CC<strong>11</strong>5<br />
9 Brush Plating Tools (use graphite<br />
anode) and Bonnets<br />
AR<br />
Separate anodes, bonnets and solution<br />
must be used at each stage of the<br />
Print Date: December 29, 2016 Page 15 of 29<br />
© AIRBUS S.A.S. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT.