GLOBAL CAT 2017

TIRE & WHEEL REPAIR 367
TIRE ROD SEPARATOR, STEPPED
LINE
CODE
PART
NO.
SHOCK ABSORBER TOOL
• FOR REMOVING AND INSTALLING SHOCK NUTS
• FITS MOST DOMESTIC MODELS AND SOME FORD OEM
SHOCK NUTS
• PLACE STEM SOCKET OVER SHOCK STEM
• HEX NUT SOCKET FITS THE NUT
• HOLD ONE, TURN THE OTHER FOR
REMOVAL
• ENDS: 9/16” , 0.591
• AVAILABLE INDIVIDUALLY
- 20420: HEX NUT SOCKET
- 20460: STEN SOCKET
- 20410: DOUBLE ENDED STEM SOCKET
LINE CODE PART NO. DESCRIPTION CASE PK.
LIS 20400 SHOCK ABSORBER TOOL 1
WHEEL STUD INSTALLER
• EASILY INSTALLS NEW WHEEL STUDS
• USE WITH A RATCHET OR IMPACT WRENCH TO PULL THE
NEW STUD SECURELY IN PLACE
• POSITION THE TOOL OVER THE STUD SHAFT
• TIGHTEN THE LUG NUT AGAINST THE
TOOL TO PULL THE STUD IN PLACE
• WORKS ON MOST AUTOMOTIVE AND
LIGHT-DUTY TRUCK WHEEL STUDS
(IMPORT AND DOMESTIC)
• BEARING WILL WEAR WITH USE AND IS
NOT WARRANTED
LINE CODE PART NO. DESCRIPTION CASE PK.
LIS 22800 WHEEL STUD INSTALLER 1
PICKLE FORK KIT
SUSPENSION
• STEPPED DESIGN HELPS LEEP TOOL FROM BOUNCING
BACK
• USED TO REPLACE WORN OUT TIRE RODS AND TO
SEPARATE SHOCK ABSORBER LINKS
• THE TINE OPENING IS 11/16”
• HEAVY-DUTY TOOL IS DROP FORGED AND
HEAT-TREATED FOR LONGER USE
• STEPS CAN BE SHARPENED
• HANDLE LENGTH: 10 1/2”
DESCRIPTION
41520 PNEUMATIC DRIVER
41510 HANDLE
41530 1 1/8” FORK
41540 15/16” FORK
41550 11/16” FORK
LINE CODE PART NO. DESCRIPTION CASE PK.
LIS 41500 PICKLE FORK KIT 1
CASE PK.
LIS 18520 TIRE ROD SEPARATOR, STEPPED 1
• FOR SEPARATING BALL JOINTS, TIE RODS, PITMAN ARMS AND
OTHER USES
• INCLUDES: THREE FORKS AND TWO HANDLES (ONE FOR
HAMMERING, ONE FOR USE WITH AN AIR HAMMER) (0.401”
SHANK) (ALL FORKS ARE THREADED TO INTERCHANGE WITH
EITHER HANDLE)
• FORKS ARE HEAVY-DUTY FORGING, HANDLES ARE HEAT-
TREATED ALLOY STEEL
BALL JOINT SEPARATOR, STEPPED
• STEPPED DESIGN HELPS LEEP TOOL FROM BOUNCING
BACK; USED TO REPLACE WORN OUT BALL JOINTS AND
TO REMOVE CV DRIVE SHAFTS ON FWD
VEHICLES
• TINE OPENING: 15/16” & DROP FORGED
AND HEAT-TREATED FOR LONGER
USE
• STEPS CAN BE SHARPENED HANDLE LENGTH: 10 1/2”
LINE CODE PART NO. DESCRIPTION
LIS 18530 BALL JOINT SEPARATOR, STEPPED
PITMAN ARM PULLER
• HEAVY DUTY PULLER WORKS ON MOST CARS &
TRUCKS
• DESIGNED TO WORK ON EVEN THE MOST STUBBORN
PITMAN ARM PULLING JOBS
• POSITION PULLER JAWS OVER
PITMAN ARM AND TURN CENTER
SCREW TO FREE PITMAN ARM
• PULLER BODY IS DROP-FORGED AND
HEAT-TREATED FOR STRENGTH
• AVAILABLE INDIVIDUALLY:
- 41910: PULLER SCREW
LINE CODE PART NO. DESCRIPTION CASE PK.
LIS 41900 PITMAN ARM PULLER 1
INNER TIE ROD TOOL
• WORKS ON TIE RODS WITH
INACCESSIBLE FLATS
• INCLUDES ADDITIONAL 1-1/2” CROWS
FOOT FOR CHEVROLET COLORADO
AND GMC CANYON
• UTILIZES SIX CROWS FEET TO
ENGAGE THE WRENCH FLATS
• LONG SOCKET SLIPS OVER TIE ROD
END AND CONNECTS TO THE CROWS
FOOT
• THE TINNER TIE ROD CAN BE
REMOVED AND INSTALLED WITHOUT
REMOVING THE RACK
• 46270 29 mm FOR TOYOTA AND 46280
32.5mm FOR FORD ARE AVAILABLE
INDEPENDENTLY
LINE CODE PART NO. DESCRIPTION CASE PK.
LIS 45750 INNER TIE ROD TOOL 1
• REMOVES INNER TIE RODS EQUIPPED WITH A
COMPLETELY ROUND END SOCKET
• FITS INNER TIE ROD SOCKETS WITH FLATS
• UNIVERSAL WRENCH DESIGNED TO REMOVE AND
INSTALL ALL INNER TIE ROD SOCKETS UP TO 1-31/64”
REGARDLESS OF THE ROD SOCKET
CONFIGURATION
• WRENCH HEAD HAS THREE SET SCREW
THAT TIGHTEN AGAINST THE ROUNDED
TIE ROD SOCKET OR SOCKET FLATS
• COMES WITH A 1/4” SHORT HEAD HEX
WRENCH FOR TIGHTENING SET SCREW IN
HARD TO REACH AREAS
• USE 1/2” DRIVE
• NO FLAT APPLICATIONS INCLUDE: ‘00- ‘03
DODGE NEON, 00’ - 01’ PLYMOUTH NEON,
01’ - 03’ DODGE AND CHRYSLER MINIVANS
• ALSO FITS SOME NO-FLAT APPLICATIONS ON FORD&
NISSAN
LINE CODE PART NO. DESCRIPTION CASE PK.
LIS 46600 INNER TIE ROD TOOL 1