REMKO RKW 1000 â 9800 INOX Stainless Steel Chiller Operation ...

More documents

Recommendations

Info

Wiring Diagram RKW 1000 INOX / 1600 INOX 22 ST 1: Temperature sensor Incoming water ST 2: Temperature sensor Outgoing water ST 5: Temperature sensor Verflüssiger HP Pressure absorber High-pressure LP Pressure absorber Low pressure Fan rotation regulation board (winter regulation) Verflüssiger fan 1 Microprocessor regulation Wiring Diagram RKW 2600 INOX ST 1: Temperature sensor Incoming water ST 2: Temperature sensor Outgoing water ST 5: Temperature sensor Condenser HP Pressure absorber High pressure LP Pressure absorber Low pressure Fan rotation regulation board (winter regulation) Overheating protection compressor Verflüssiger fan 2 Microprocessor regulation Potentialfreier Kontakt for regulating cooling EXTERNAL Neutral contact for cooling regulation EXTERNAL Differential pressure monitor INTERN Flow switch EXTERNAL Circulation pump Differential pressure monitor IN- TERNAL Condenser motor Circulation pump Terminal strip M2 Compressor motor Condenser fan 1 Relay condenser Terminal strip M1 Relay compressor Input 400 V / 3 Ph ~ / 50 Hz Input 400 V / 3 Ph ~ / 50 Hz Terminal strip M2 Terminal strip M1 Phase-sequence relay Phase-sequence relay
Electrical Wiring Diagram RKW 3600 INOX / 4500 INOX ST 1: Temperature Incoming water ST 2: Temperature sensor outgoing water ST 5: Temperature sensor HP Pressure absorber High pressure LP Pressure absorber Low pressure Microprocessor regulation Additional module Overheating protection condenser Overheating protection condenser 1 Neutral contact for cooling regulation EXTERNAL Differential pressure monitor INTERNAL Condenser fan 1 Connecting the Remote Control RKW 1000 INOX to 9800 INOX Assembly Instructions CH – DIN regulation / C2 – DIN regulation 1. Place the two connection lines with a minimum cross-section of Cu 1.5 mm² between the RKW and the operating module (max. 50 m). BUS 2. Connect the operating module electrically. 3. Switch the RKW so that it is neutral (i.e. no current) and connect the 250 mm long bus-interface line to the additional module. 4. Connect the line of the data transfer to the terminal strips 23 and 24 (pay attention to polarity) of the additional module and the terminal strips on the transformer for the current supply. 12V 12V in out BUS Compressor motor 1 Compressor motor 2 Terminal strip M2 Condenser fan 2 Frequency block Frequency block Circulation pump Fan rotation regulation board TK 1 and TK 2 (winter regulation) L1 N Additional module for the remote control Operating module TS-W CS-DIN/TTL 20 21 22 23 24 Input 400 V / 3 Ph ~, N, PE 50 Hz 12V 12V Pri L1 230V~ N Terminal strip M1 Transformer 220 / 12 V~ in the switch box RKW Maximum line length 50 meter 23 Phase- sequence relay
Page 1: REMKO RKW 1000 - 9800 INOX Stainles
Page 4 and 5: Unit Description REMKO chilled wate
Page 6 and 7: Regulation CH-DIN regulation of all
Page 8 and 9: Determining the Operating Mode (Sta
Page 10 and 11: Shutting Down the Unit Temporary sh
Page 12 and 13: Technical Data Type RKW INOX Coolin
Page 14 and 15: Assembly Instructions for Service P
Page 16 and 17: Hydraulic connections The hydraulic
Page 18 and 19: Storage Module Technical Data 18 36
Page 20 and 21: Antifreeze to prevent freezing Duri
Page 24 and 25: Electrical Wiring Diagram RKW 8000
Page 26: Operation The unit must be put into

REMKO RKW 1000 â 9800 INOX Stainless Steel Chiller Operation ...

Create successful ePaper yourself

Delete template?

Save as template?

REMKO RKW 1000 â 9800 INOX Stainless Steel Chiller Operation ...