Socomec UL General Catalog

DIRIS A-20
Multifunction power metering & monitoring device - PMD
Multi-measurement
Electrical characteristics
Current measurement (TRMS)
Via CT primary
9 999 A
Via CT secondary
5 A
Measurement range
0 … 11 kA
Input consumption
0.6 VA
Measurement updating period
1 s
Accuracy 0.2%
Permanent overload
6 A
Intermittent overload
10 I n over 1 sec
Voltage measurements (TRMS)
Direct measurement between phases 50 … 500 VAC
Direct measurement between phase
and neutral
28 … 289 VAC
Input consumption
0.1 VA
Measurement updating period
1 s
Accuracy 0.2%
Power measurement
Measurement updating period
1 s
Accuracy 0.5%
Power factor measurement
Measurement updating period
1 s
Accuracy 0.5%
Frequency measurement
Measurement range
45 … 65 Hz
Measurement updating period
1 s
Accuracy 0.1%
Terminals
Energy accuracy
Active (according to IEC 62053-22) Class 0.5 S
Reactive (in acc. with CEI 62053-23) Class 2
Auxiliary power supply
Alternative voltage
110 … 400 VAC
AC tolerance ± 10%
DC voltage
120 … 289 VDC
DC tolerance ± 20%
Frequency
50 / 60 Hz
Power consumption
10 VA
Pulse or alarm output
Number 1
Type
100 VDC - 0.5 A - 10 VA
Max. number of manoeuvres 10 8
Inputs
Number 3
Power supply
10 … 30 VDC
Minimum width of signal
10 ms
Minimum length between 2 pulses 18 ms
Type
Optical couplers
Communication
Link
RS485
Type
2 to 3 half duplex wires
Protocol
MODBUS ® in RTU mode
MODBUS ® speed
1400 … 38400 baud
Operating conditions
Operating temperature range - 10 … + 55 °C / +14 °F … +131 °F
Storage temperature - 20 … + 70 °C / -4 °F … +158 °F
Relative humidity 95%
DIRIS_578_a_1_x_cat
V1
DIRIS A20
V2
V3
VN
A U X
S1 S2 S1 S2 S1 S2
I1 I2 I3
S1 - S2 : current inputs.
AUX : auxiliary power supply U s .
V1, V2, V3 & VN : voltage inputs.
Module communication
Output or alarm module
Module with 3 inputs, 1 output
DIRIS_579_a_1_x_cat
0V - +
RS485
Connection
1
0n
R = 120
DIRIS A20
RS485 link.
R = 120 : internal resistance for
the RS485 link.
Low voltage balanced network
DIRIS_580_b_1_x_cat
DIRIS A20
18 19
OUT 1
18 - 19 : output n°1
+ - + - + -
12 13 14 15 16 17
IN 3
DIRIS A20
Recommendation
- For IT earthing systems, it is recommended that the CT secondary is not connected to earth.
- When disconnecting the DIRIS, the secondary of each current transformer must be short-circuited. This operation can be carried out automatically
by a SOCOMEC PTI: please consult us.
3/4 wires with 1 CT Single-phase Two-phase
N
P1
P1
L1
L1
S1 S2
S1 S2
L2
N
L3
IN 2
IN 1
P1
S1
19 18
OUT 1
S2
L1
L2
1 1 1
1
1 1
diris_392_d_1_x_cat
V1 V2 V3 VN
S1
I1
S2
S1
I2
S2
S1
I3
S2
diris_393_d_1_x_cat
V1 V2 V3 VN
S1 S2 S1 S2 S1 S2
I1 I2 I3
diris_394_d_1_x_cat
V1 V2 V3 VN
S1 S2 S1 S2 S1 S2
I1 I2 I3
The 1CT solution reduces by 0.5% the accuracy of the phase
for which the current is deduced by a vector calculation.
1. 0.5 A gG / 0.5 A class CC fuses.
1. 0.5 A gG / 0.5 A class CC fuses.
1. 0.5 A gG / 0.5 A class CC fuses.
264 General Catalog UL/CSA Ed. 2