24/06/2005 - Controller General of Patents, Designs, and Trade Marks

The Patent Office Journal 24.06.2005 17689

INTRODUCTION 

In view of the recent amendment made in the Patents Act, 1970 by the 

Patents (Amendment) Act, 2005 effective from 01 st January 2005, the 

Official Journal of The Patent Office is required to be published under the 

Statute. This Journal is being published on weekly basis on every Friday 

covering the various proceedings on Patents as required according to the 

provision of Section 145 of the Patents Act 1970. 

All the enquiries on this Official Journal and other information as required by 

the public should be addressed to the Controller General of Patents, Designs 

& Trade Marks. Suggestions and comments are requested from all quarters 

so that the content can be enriched. 

24 th June, 2005. 

(S. CHANDRASEKARAN) 

Controller Genera] of Patents, Designs 

& Trade Marks 


CONTENTS 

Subject Page Nos. 

Jurisdiction : 17692-17693 

Special Notice : 17694-17696 

CORRIGENDUM 

: 

17697 

Early Publication (Mumbai) 

17698-17733 

Early Publication(Kolkata) 

: 17734-17735 

Early Publication (Delhi) : 17736-17738 

18 th Month Publication (Mumbai) 

: 17739-18001 

18 th Month Publication (Kolkata) : 18002-18080 

18 th Month Publication (Delhi) : 18081-18240 

Patent Granted (Delhi) : 18241 





Special notice 

1. The Patent Office, Kolkata has been shifted on 06.06.2005 from 5, 6 & 7 th 

floor, 2 nd M.S.O Building, Nizam Palace, 234/4 A.J.C Bose Road, Kolkata – 700 020 to 

the new location, at the address given below- 

The Patent Office, 

Government of India, 

Boudhik Sampada Bhavan, 

CP-2, Sector –V, Salt Lake City, 

Kolkata – 700 091 

All communications should be made to the new address . All the services of the Patent 

Office are available in the new location from the above mentioned date. For further 

details visit our website: ipindia.nic.in 

2. Every effort is being taken to publish all the patent applications 

under section 11(A) of the Patents Act. However, if duplication of 

publication of any application is found, then earlier date of publication 

will be taken for the purpose of provisional protection for applicant and 

Patent Office will grant Patent only after three months from the date of 

second publication, provided that there is no third party representation. 


Special Notice 

Under the new provision of the Patents Act, 1970 as amended by the Patents (Amendment) ) Ordnance, 

2004 and Rules thereunder, Publication of the matter relating to Patent in the Official Gazette of India 

Part III, Section 2 has been discontinued and instead The Official Journal of the Patent Office is being 

published containing that matter on weekly basis on every Friday since 21 st January, 2005 

The price of each copy of the journal is Rs. 400/- in paper form and that is Rs. 250/- in CD-ROM form, 

while annual subscription of the journal for a calendar year is Rs. 20,000/- in paper form and that is Rs. 

12,000/- in CD-ROM form . Postal Charges are to be paid extra. 

Interested persons or organisations may send their annual subscription to or purchase individual copies 

from any of the Patent Office at Kolkata, New Delhi, Mumbai and Chennai. 

A request should be made accompanied by payment in cash or cheque/Demand Draft drawn in favour of 

the Controller of Patents, payable at the respective Office. Other mode of payment i.e. M.O/I.P.O. or 

any out station cheque will not be accepted. The annual subscription should be made immediately 

preferably on or before 25 th July, 2005. 


CORRIGENDUM 

1. The application for Patent No. 192633 (Patent Application No. 

1327/Mas/1995) granted only on 04/05/2005 which was inadvertently notified on 

18/03/2005 under the heading “ PATENT GRANTED ON 03/02/2005.’ 

2. Indian National Phase Mailbox Patent Application NO. 192/MUMNP/2003 which 

was published on The Patent Office Journal dated 04.03.2005 with the Address of the 

Applicant as “ S- 151 85 SODERTALJE SWEDEN”. The Correct address should be read 

as 

“ BUYUKDERE CADDESI NO. 205 

4, LEVENT , 80650, 

ISTANBUL, TURKEY.” 

3. Indian National Phase Mailbox Patent Application NO. 296/MUMNP/2004 which 

was published on The Patent Office Journal dated 29/04/2005 with the Name of Applicant 

as “ VASPLAY INTERNATIONAL AG”. The correct name of the Applicant should be 

read as “ VISPLAY INTERNATIONAL AG”. 


“Early Publication 

The following patent applications have been published under section 11A (2) of The Patents (Amendment) Act 

2005 and rule 24A of The Patents (Amendment) Rules, 2005.. Any Person interested may file Representation 

by way of opposition to the Controller of Patents at the appropriate office against the grant of the patent in the 

prescribed manner under section 25(1) of the Patents (Amendment) Act 2005 read with the rule 55 of The 

Patents (Amendment) Rules, 2005 : ” 

EARLY PUBLICATION 

(12) PATENT APPLICATION PUBLICATION 

(19) INDIA (21) 

(22) Date of filing of 

Application: 

24/11/2000 

Application No: 1065/MUM/2000 A 

(43) Publication Date: 

24/06/2005 

(54) Title of the invention: “HIGH THERMAL EFFICIENCY STOVE”. 

(51) International 

Classification: 

F23D 3/02, 3/08 (71) 

(31) Priority Document No.: NIL 

(32) Priority Date: 

NIL 

(33) Name of priority country: NIL 

(86) 

International Application No. & Filing Date: 

NIL 

NIL 

(87) International Publication No.: NIL 

(61) 

(62) 

Patent of addition to Application No.: NIL 

Filed on: N.A. 

Divisional to 

Application No.: NIL 


(57) Abstract : An improved stove which consists of :- 

(72) 

Name of the Applicant: 

VINOD CHIRANJEEV MALSHE 

Address of the Applicant: 

1, UNIVERSITY STAFF QUARTORS, 

UDCT CAMPUS, MATUNGA, 

MUMBAI – 400 019. 

MAHARASHTRA, INDIA 

Name of the Inventors: 

-IDEM- 

Filed U/S 5(2) before the 

Patents (Amendment) 

Ordinance, 2004: NO 

a) provision for recycle of radiant heat through preheating of combustion air, 

b) insulation selected form loose filled insulation such as expanded vermiculite, ceramic fibers, hollow 

spheres of glass, other ceramic material or floating fly ash from thermal power station bloated clays, 

pumice stone or the like. 

c) high radiation efficiency paints on all the internal parts. The paint may be prepared from bright metal 

powders such a aluminum, stainless steel or the like. 

(FIG. ): NIL 

Total pages : 7 



(19) INDIA (21) 


Application: 

26/02/2004 (43) 


Application No: 239/MUM/2004 A 

Publication Date: 24/06/2005 

(54) Title of the invention: A TOPICAL ANALGESIC AND RUBAFACIENT 



A61K 31/195, A61K 9/06 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


SANJEEV KHANDELWAL 


PREM NIVAS, 13, ALTAMOUNT 

ROAD, MUMBAI 400 026, 







(57) Abstract : Method and composition are provided for effective relief of pain on topical application. The 

composition comprises a synergistic composition and the method of making the same is disclosed. The 

composition contains an anlgesic, anti-inflammatory agent diclofenac, and at least one synergistic 

rubafacients in a topical gel formulation. The synergistic rubafacient may include menthol, methyl 

salicylate, oleum lini, capsaicin etc. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 

(54) Title of the invention: 

23/03/2004 (43) 



A61K 3/00 (71) 






A METHOD OF MAKING NON-TOXIC EDIBLE ENTERIC 

COOKING READY TO USE DRY POWDER COMPOSITION 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


IDEAL CURES PVT. LTD 


6 th FLOOR, ELECON CHAMBER, 

ANDHER-KURLA ROAD, 

KAKINAKA, ANDHERI (EAST), 

MUMBAI 400 072, MAHARASHTRA, 

INDIA 


1. Mr. SURESH PAREEK 

2. Mr. ASHOK MOHANTY 

3. Mr. CHETAN RAJSHARAD 

4. Mr. SHIVAJI KAMBLE 




(57) Abstract : This invention is in the field of enteric film coating, dry powder compositions for coating 

pharmaceutical dosage forms. It relates to nonaqueous enteric coating and provides a dry enteric film coat 

composition based on an acrylate copolymer and other excipients, but without an alkalinizing agent in the 

composition. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


12/05/2004 (43) 



F16K 49/00, B28D 1/08 (71) 






APPARATUS FOR SEPARATING TOW FLUIDS WITH THAWING 

DIFFERENT TEMPERATURES & DIFFERENT DENSITIES 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


AGHARKAR RESEARCH 

INSTITUTE OF MAHARASHTRA 

ASSOCIATION FOR THE 

CULTIVATION OF SCIENCE 


G.G. AGARKAR ROAD, 

PUNE 411 004, MAHARASHTRA, 

INDIA 


KISHORE MADHUKAR PAKNIKAR 




(57) Abstract : A method of separating from a mixture, two fluids of different densities, where the denser 

fluid thaws at a lower temperature than the temperature at which the lighter fluid thaws is described. The 

mixture is filled in a polycarbonate bottle having a sampling cup thereon. The bottle is frozen. The denser 

fluid settled at the bottom thaws first. The frozen mass of lighter fluid on top bears on the liquidized fluid 

and pushes it up through a pipe into the sampling cup. The apparatus is particular suitable for separating a 

mass of nano particles from its media. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


12/05/2004 (43) 



A61K 35/78, A61P 27/02 (71) 






PROCESS FOR MAKING EYE DROPS &EYE DROPS MADE BY 

THE PROCESS 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


DR. BHUSARI DILIP BHURAOJI 


10, SHIVNANDAN B, BHUSARI 

COLONY, NEAR P.M.T.DEPOT, 

PAUD ROAD, KOTHRUD, 

PUNE – 411 038 MAHARASHTRA, 

INDIA, 


DR. BHUSARI DILIP BHURAOJI 




(57) Abstract : An ophthalmic formulation comprising hot saline extract [0.9% sodium chloride] of a 

mixture of powders consisting Glycyrrhiza glabra, moringa oleifera, Terminalia chebula, Terminalia 

belerica, Emblica officinalis Albizzia lebbeck, Carum bulbocastanum, Boerhaavia diffusa, intimately dried 

gum of Cinnamomum comphora, Nees and honey, 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 

24/05/2004 (43) 

(54) Title of the invention: VEDIC MULTIPLIER 



G06F 7/52 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 





(72) 



ASHTEKAR DHARMENDRA 

SUDHAKAR 


C/O S.M. SANSARE, 

THRIMURTI C.H.S., 509/C-1 

CHARKOP, SECTOR- 5, 

KANDIVLI (W), MUMBAI 400 067. 


ASHTEKAR DHARMENDRA 

SUDHAKAR 




(57) Abstract : Two bit Vedic Multiplier circuit carries out multiplication of two binary numbers, with a time 

delay of 2 logic gates. This circuit doesn’t make use of shift registers. By adopting this technique of Vedic 

Multiplier for higher values of ‘n’ time taken for multiplication of two binary numbers is reduced. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 

16/06/200 

4 



(43) 


(54) Title of the invention: PORTABLE CASTOR WHEEL STAND FOR TWO WHEELERS 



B62B 1/18, 1/20 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


ANANT NARAYAN LIMAYE 


1-21, ‘BILWA’ SHILP NAGAR, 

OPP. MARIA HOSPITAL, STATION 

ROAD, AURANGABAD, 

MAHARSHTRA, INDIA 


ANANT NARAYAN LIMAYE 




(57) Abstract : Portable castor or cartwheel device for two wheeler automobiles comprising: 

two longitudinal telescopic arms; 

a base member; 

two pivotal non-swiveling castor wheels’ threaded fastening means and; 

a bracket; 

the said two longitudinal telescopic arms being interconnected to the axle of the vehicle through said threaded 

means and bracket and said threaded fastener means being insertable into bracket, said base member being 

perpendicular to the said arms, removably interconnected between said telescopic arms intersecting thorough the 

wheel of the vehicle, said castor wheels rotatbly attached to the remote ends of said telecopic arms there by 

making easier to move the two-wheeler when the tyre of the two-wheeler is punctured or there is some 

mechanical fault. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


08/07/2004 (43) 



C07D 7/00 (71) 






METHOD AND SYSTEM FOR CHEQUE DEPOSIT WITH IMAGE 

ACKNOWLEDGEMENT 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


ICICI BANK LIMITED 


ICICI BANK TOWERS, BANDRA 

KURLA COMPLEX, BANDRA (E), 

MUMBAI, MAHARASHTRA, INDIA 


1. BUCH MADHABI PURI 

2. PK NIRMAL 

3. BAJAJ ANAND 




(57) Abstract : The present invention relates to an unattended system for depositing the cheques in a bank 

with proper acknowledgement. The cheque deposit stations as per the invention are machines connected to 

the bank’s central server and accept the cheque and issue an acknowledgement for the user with the image 

of the cheque. The stations also keep a log of transactions, which is used to generate various files for 

cheque’s verification and validation, clearing of the cheque, and customer service. 

(FIG. ) : NIL 





(19) INDIA (21) Application No: 800/MUM/2004 A 


Application: 




A61K 35/00 (71) 



29/07/2004 (43) Publication Date: 24/06/2005 

A PROCESS FOR PREPARING OF AEROSOL BASE, 

MOSQUITOCIDAL AND HOUSEFLAYCIDAL FORMULATION 

FROM HERBAL EXTRACTS 

NIL 


(86) 


NIL 

NIL 



1. M/S ENDU HERBAL & PLANT 

PRODUCTS PRIVATE LIMITED 

2. DR. VIDYA LAGAMANA PATIL 


SIDDHIVINAYAK APT., 1 st FLOOR, 

PLOT NO. B-34, SECTOR – 20, 

NERUL (W), NAVI MUMBAI 400 706, 



(61) Patent of addition to Application No.: NIL (72) 1. DR. VIDYA LAGAMANA PATIL 

Filed on: N.A. 2. SATISH LAGAMANA PATIL 

3. SABDEEP LAGAMANA PATIL 

(62) Divisional to 






(57) Abstract : A process for preparing aerosol base mosquitocidal and housefly cidal formation from herbal 

extracts. 

The natural and synthetic insecticides available in the market are less used for the control of mosquitoes and housefly. 

Since their side effects and costs. The four plants used for insecticide preparation are ocimum tenuiflorum linn., 

Azadirachta indica juss., Ocimum basilicum Linn., Eucalyptus glubolus juss have been used in powdered form. 

Individually tested for bio efficacy against Anopheles stephensi, culex-quinquefasiatus mosquitoes and musca 

domestica, housefly study. But have not given effective activity. The combine four plants powder at 400mgs has given 

100% mortality against the above said mosquitoes. This invention has provoked for further durable, effective, and safe 

insecticide prepartion and to obtained it the extraction method is used. 

The extracts of four different plants was obtained by using petroleum ether as extracting solvent, refluction in soxhlet at 

the temperture 50˚ C -60˚ C for 8.0hours. After complete evaporating of petroleum ether from the extract. 5% extract test 

solution was prepared using aerosol as adissolving solvent for spray, the synergistic effect of this formulation was tested 

for bio-effcacy study against Anopheles stephensi, culex-quinquefasiatus mosquitoes and Musca domestica housefly. 

This formulation gives 91%, 92% and 87% mortalities and KT50 (minutes) 12.91, 15.85 and 21.91 against Anopheles 

stephensi, Culex-quinquefasiatus mosquitoes and Musca domestica housefly respectively. Generally herbal extract 

formulations KT50 values are found in between 22-25min-against mosquitoes while against housefly it is ranged between 

25-28min. This is a substitute formulation of herbal origin in aerosol solvent to a existing less active plant product 

formulations and harmful synthetic formulations. 

(FIG. ) : NIL 


The Patent Office Journal 24.06.2005 17706





Application: 

05/08/2004 (43) Publication Date: 24/06/2005 

(54) Title of the invention: TRACK IDENTIFICATION SYSTEM 



B61L 3/00, B61L 23/00 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


KONKAN RAILWAY 

CORPORATION LIMITED 


BELAPUR BHAVAN, SECTOR 11, 

CBD, BELAPUR 

NAVI MUMBAI 400 614, 



BOJJI RAJARAM 




(57) Abstract : A track identification system for a plurality of locomotives moving on defined plurality of 

tracks, said tracks having uniquely identifiable switching locations where said locomotives can switch 

movement from one track to movement on to one or more other tracks, said tracks passing through a 

railway network consisting of locomotives, stationary structures such as stations, crossings, yards, said 

system consisting of on board computers fitted to each of the locomotives, said on board computers having 

storage means to eraseably store digitally encoded information of at least a portion of the route and track 

data relating to the said plurality of tracks, each of said uniquely identifiable switching locations, and the 

parameters of movement of the locomotives along the said tracks, said computers having processors 

programmed to receive reference location signals of the locomotive from a global positioning system and 

thereby determine the precise geographical locations of the locomotives, said computers further 

programmed to digitally map at least a portion of the determined geographical locations on the stored route 

and track data, and to continuously monitor the movement of the locomotives with reference to parameters 

such as their location coordinates, velocity and angular change profile at the said switching location 

coordinates, velocity and angular change profile at the said switching locations, and further having 

programming means to compute the angular change profile to determine switching actions at the said 

switching locations and programmed signal generator means operable by the said processing means to 

generate signals relative to the angular change profile relating to switching actions at the switching 

locations thereby determining the tracks on which the movement of each of the locomotives is occurring 

and the velocity of such movement. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


30/08/2004 (43) 



A61K 31/196 (71) 






AN ANTISPASMODIC AND NSAID ORAL TABLET AND METHOD 

OF MAKING THE SAME 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 




PREM NIVAS, 13, ALTAMOUNT 

ROAD, MUMBAI 400 026, 







(57) Abstract : Methods and composition are provided for effective relief of spasmodic pain. The 

composition comprises a synergistic formulation. Method of making the same are also disclosed. The 

composition contains camylofin dihydrochloride and diclofenac in an oral pharmaceutical formulation if a 

single tablet dosage form. The method includes forming a core containing granules of the active ingredients 

with excipients and coating the cores with at least one and preferably two film coats. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 

02/09/2004 (43) 




(54) Title of the invention: PROCESS FOR PREPARATION OF STABLE POLYMORPH 



C07D 401/14, A61K 031/506 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


M/S. CIPLA LIMITED 


289, BELLASIS ROAD, MUMBAI 

CENTRAL, MUMBAI – 400 008, 



1. PATHI SRINIVAS 

LAXMINARAYAN 

2. PUPPALA RAVIKUMAR 

3. KANKAN RAJENDRA 

NARAYANRAO 

4. RAO DHARMARAJ CHANDRA 




(57) Abstract : A process for preparation of stable, non hygroscopic alpha crystalline form of methane 

sulfonic acid addition salt of 4-(4-methyl piperazin-1yl methyl)-N-[4-methyl-3-(4-pyridin-3-yl) pyrimidin- 

2-yl amino) phenyl]-benzamide (imatinib mesylate) is disclosed herein. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 

11/10/2004 (43) 




(54) Title of the invention: FLEXIBLE POUCH JAR WITH REUSABILITY AND DURABILITY 



B65D 77/06, B65D 33/01 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


MANDHANIA ANIL BALKRISHNA 


C-81, AAKASH TOWER, 

PREMCHAND NAGAR ROAD, 

BODAKDEV, SATELLITE, 

AHMEDABAD – 380 015, 

GUJARAT, INDIA 


MANDHANIA ANIL BALKRISHNA 




(57) Abstract : REUSABE FLEXIBLE POUCH JAR comprises of a flexible plastic pouch a solid cover 

sealed over the said pouch with a mouth and a cap or closure over the mouth and with an additional bas of 

the bottom of the pouch jar. 

(FIG. ) : NIL 







Application: 


30/11/200 

4 



G06F 13/00, H04L 12/46 (71) 



(43) Publication Date: 24/06/2005 

A SMART SYSTEM AND METHOD FOR INFORMATION 

COLLECTION, ORGANIZATION, INTEGRATION, 

COLLABORATION AND DISTRIBUTION FOR DEVELOPMENT 

OF NETWORKED COMMUNITY BY SECURE MEANS OF 

TRUSTED LAYERED NETWORKING 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


WHITE VISION SOFTWARE PVT. 

LTD. 


SHOP NO. 3 & 4 SAI SMURTHI, 

B.K. TIWARI MARG, 

BEHIND DEEP MANDIR THEATRE, 

MULUND (W), MUMBAI – 400 080, 



1. Mr. RATHOD RAJESH 

2. Mr. RATHOD YOGESH 




(57) Abstract : The present invention devices a system and method to build a universally distributed 

application in an organized way that engrosses supercomputing capabilities into the framework which form 

a computing grid comprising of disparate universally distributed computer systems enabling formation of 

communication & computation network and a n effective means for alternative ways to utilize presently 

unorganized internet framework. The distributed network comprises of multiple clients at specified level of 

operation in the network architecture that essentially follows Trusted Flexible Hierarchical Layer (TFHL). 

Networking standards devised to establish alternative communication methodology to internet as well as 

social & enterprise communication frame work. 

In an another important embodiment of the invention the distributed network communication is made 

possible by means of Net Alter Managers and same can be used to operate the network activities and 

computation in multiple ways like peer to peer, offline, online, smart device etc. The manager helps manage 

the network operation and is the means to administrative functions and information management. The 

invention overcomes substantially all the presents flaws in presently available internet framework, peer to 

peer and grid computing. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 

27/12/200 

4 



(43) 


(54) Title of the invention: SHIMLESS SUPPORTING & CLAMPING DEVICE FOR FIXTURES 



B23Q 16/00, B25B 11/00 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


M/S. CONEX AVIO AUTO PVT. LTD. 


55, AMCHI COLONY, PASHAN – 

NDA ROAD, BAWDHAN, 

PUNE- 411 021. MAHARASHTRA, 

INDIA 


MR. VINOD DAMODAR 

VYAWAHARE 




(57) Abstract : A device useful for supporting and clamping function in Welding, Assembly, Checking 

Fixtures for holding sheet metal parts is disclosed. The supporting function is achieved using Wedges (12) 

and hence is more accurate, fast and rigid. 

The toggle clamping function is provided with guided Clamping Arm (8), Eccentric Pin (14) and Bronze 

Bushes (13) thus resulting in smooth, repeatable, long life operation with feasibility of prolonging the life. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


13/01/200 

5 


Application No: 31/MUM/2005 A 

(43) 



A61K 35/78 (71) 




AN HERBAL COMPOSITION FOR TREATMENT OF BLOOD 

RELATED AND HEART DISEASE 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


RAMA DHONDIBA KATKAR 


FLAT NO. 902, SAHWAS SHREE, 

HOUSING SOCIETY, MIRA NAGER, 

NEAR ROHI-VILLA PALACE, 

NORTH MAIN ROAD, 

KOREGAON-PARK, PUNE 411 001. 


1. RAMA DHONDIBA KATKAR 

2. ASHA 




(57) Abstract : An herbal composition for treatment of blood and heart / skin related diseases comprising 

the following herbs 

Sr. No. Herb 

% used 

1. Murraya Paniculat (Bhutkati) 15 to 30% 

2. Latana camara (Ghanera or tantani) 10 to 06% 

3. Terminalia (kinjal) 10 to 70% 

4. Todalia asiatica(jangli-Mirch) 10 to 50% 

5. Chawat or dhundari 10 to 70% 

6. Teak wood 5 to 60% 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


04/02/200 

5 



(43) 



C12N 1/14, A01N 63/04 (71) 




A PROCESS FOR THE PREPARATION OF MAGGOT CONTROL 

FORMULATION OF BEAUVARIA BASSIANA AND 

FORMULATION OBTAINED THEREFROM. 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


SUDARSHAN CHEMICAL 

INDUSTRIES LTD. 


162, WELLESLEY ROAD, 

PUNE R11 001, MAHARASHTRA, 

INDIA 


1. DR. DUDHBHATE JAIDEEP 

ANANT 

2. NALAWADE ARVIND PRAKASH 

3. RAJPATHAK MILIND 

BALKRISHNA 

4. KULKARNI 

CHANDRASHEKHAR GOVIND 




(57) Abstract : This invention relates to a process for forming maggot control formulation of beau aria 

bassiana in poultry industry by growing beau aria bassiana in laboratory and forming the biological wet 

table powder (WP) product. The said BWP is formed of 20-80% active Imidachloprid. The wettable powder 

is mixed with the Beauvaria bassiana in the range 1 to 50% by weight to form maggot control formulation 

resulting in concentration in the range of 0.1% to 0.5% of wet table powder in the 20 gms./Itr. Mixture. The 

chemical named Dichlorvos can also be mixed optionally in the proportion 1% by weight of the total 

formulation. 

(FIG. ) : NIL 





(19) INDIA (21) Application No: 138/MUM/2005 A 


Application: 


10/02/200 

5 



B65D 27/08 (71) 




A NEW VERSATILE DEVELOPMENT PROFILE FOR AN 

ENVELOPE 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(57) Abstract : 

This invention relates to a new versatile 

development profile for envelope without 

any overlaps wherein the flaps meets at seem 

without any overlaps, depending upon the 

type of the envelope i.e. pocket and / or 

banker and which provides convenience for 

inserting the documents. An allowance for 

overlaps could also be provide on basic flaps 

in a manner that non-parallel side of 

development profile match with each other, 

which could be uniform or otherwise as per 

specific requirement. 

(FIG. ) : 3.1 


(72) 


BHUSKUTE MADHAO 

MADHUSUDAN 


A/103, PRUTHVI TOWERS, 

NEAR KARNAVATI APARTMENTS, 

JODHPUR CHAR RASTA, 

SATELLITE AREA, AHMEDABAD- 

380 015, GUJARAT STATE 


BHUSKUTE MADHAO 

MADHUSUDAN 






(19) INDIA (21) 


Application: 

11/02/2005 (43) 

(54) Title of the invention: HERBAL HAIR OIL 



A61K 1/06 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 





(72) 



KEDARNATH MOHANLAL LOHE 


1163, MAIN ROAD, AT- 

SANGAMNER, 422 605, 

DIST.- AHMED NAGAR 


KEDARNATH MOHANLAL LOHE 




(57) Abstract : An ayurvedic herbal hair oil composition and preparation thereof, comprising a jatamasi 

extract (jatamashi Nardostachys) is selected in the range 2.5 ml to 6.5 ml, and taking a amla oil in the range 

of 2 ml to 5ml and bramhi (Gratiola) extract is taken in the range of 2.5 l to 5.5ml, and bhrunjraj (Thistles) 

eclipta alba extractant is taken in the range of 2ml to 6ml, and nagamothra (cyperus rotundus) extract in the 

range of 2ml to 6ml, and kapurkachari extract (Hedy chim spicatum) in the range of 2ml to 5ml, and kavath 

extract (feronia elephantum) in the range of 1ml to 4ml, and bachi extract is selected in the range of 1ml of 

4ml. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


25/02/2005 (43) 



G06F 17/50 (71) 






A SYSTEM AND METHOD FOR EMULATING A LOGIC CIRCUIT 

DESIGN USING PROGRAMMABLELOGIC DEVICES 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


POWAI LABS. TECHNOLOGY PVT. 

LTD. 


4 th FLOOR, KRESIT, LLT-BOMBAY, 

POWAI, MUMBAI – 400 076, INDIA 


1. MADHAV P. DESAI 

2. MITRA SUDHIR PURANDARE 

3. HIMANSHU SHARMA 

4. SACHIN B. PATKAR 




(57) Abstract : The present system provides a number of hardware and software modules that emulate 

logic circuit designs for simulation purposes. The present system receives an intial logic circuit design and 

provides algorithms to recode, weight partition and interconnect an emulated logic circuit wherein the 

features of the original circuit design are preserved. The system further provides a monitoring of the internal 

signals within the emulated circuit. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


22/03/2005 (43) 



A612K 39/12 (71) 






AN IMPROVED FORMULATION OF NUCLEAR POLYHEDROSIS 

VIRUS AND A PROCESS FOR PREPARING THE SAME 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


SUDARSHAN CHEMICAL 

INDUSTRIES LTD. 


162, WELLESLEY ROAD, 

PUNE R11 001, MAHARASHTRA, 

INDIA 


1. DR. DUDHBHATE JAIDEEP 

ANANT 

2. NALAWADE ARVIND PRAKASH 

3. RAJPATHAK MILIND 

BALKRISHNA 

4. KULKARNI 

CHANDRASHEKHAR GOVIND 




(57) Abstract : The present invention relates to process for preparing an improved formulation of a Nuclear 

Polyhedrosis Virus (NPV) and for such formulations. The process comprises of adding and mixing NPV 

with a catalyst which also acts as stabilizer such as 0.01% to 4% sulphide, 0.1% to 5% chloride, 0.1% to 5% 

thiosulphate of sodium or potassium in water in the presence or absence of isopropyl alcohol or propylene 

glycol or ethylene glycol, the pH in the range of 4-9 at ambient temperature and the resultant solution is 

then checked for the POB (polyhedral occlusion body) count at the end of the 13 months which should be in 

the range of 0.5 x 10 8 to 2 x 10 8 and then packed in plastic bottle of suitable size for storage at room 

temperature 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


22/03/2005 (43) 



A61K 9/48, A61K 38/43 (71) 






SOFT GELATING CAPSULE MADE WITH NATTOKINASE AND 

VARIANTS THEREOF 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


DILIP S. DAHANUKAR 


INDUSTRIAL ASSURANCE 

BLILDING, CHURCHGATE, 


INDIA 


DILIP S. DAHANUKAR 



Ordinance, 2004: YES 

(57) Abstract : A soft gelatine seamless capsule for oral administration comprising a shell and filling 

wherein the total fill weight of 250 mg to 1800mg containing a paste made out of oil and or Hydrogenated 

Vegetable Oil (HVO) containing 20 to 150mg Nattokinase powder, along with colostrums powder and/or 

vitamins/herbal preparation. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


24/03/2005 (43) 



E04C 2/24, E04C 2/26 (71) 






MULTIPURPOSE GROUNDSHEET PP/TPO COMPOSITE 

LAMINATE 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


M/S. ENTERMONDE 

POLYECOATERS LTD. 


KILFIRE HOUSE, C-17, DALIA 

INDUSTRIAL AREA, OFF LINK 

ROAD, ANDHERI (WEST), 

MUMBAI 400 053. 


1. MR. M.M. KHANDWE 

2. MR. A.K. MODY 




(57) Abstract : The present invention is “Multipurpose Ground Sheet PP/TPO composite Laminate” 

comprising of:- 

a three layer composite of PP fabric using TPO is described. TPO forms essentially as an adhesive and 

water proofing middle layer in the composite and PP fabric form outer layers. The composite can be 

stitched or welded on the edges or as per requirement of size to form a multipurpose groundsheet. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


31/03/200 

5 



(43) 



A01K 05/00 (71) 




A NOVEL DEVICE FOR MANUFACTURING NON TRADITIONAL 

LIVE STOCK ANIMAL FEEDS 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


MARUTI AGRO INDUSTRIES 


OPP. MOTI PROTEIN INDUSTRIES, 

N.H. NO. 8A, SARKHEJ-BAVLA 

ROAD, CHANGODAR, 

TALUKA SANAND, DIST. 

AHMEDABAD- 382 213. 



PALA NALIN NAROTTAMDAS 




(57) Abstract : A NOVEL DEVICE FOR MANUFACTURING NON TRADITIONAL LIVE STOCK 

ANIMAL FEEDS is device for manufacturing non-traditional live stock animal feeds which comprise 

a food mixture containing rice bran, ground nut, Sal seed, Soya, Soya meal, wheat beam, gram barns, 

sterilized fish meal, sterilized Fish meal, compressed in cylindrical shape beans. A compressed bean based 

composite, which is economical to store and transport. The beans can provide a great deal of protein at very 

low cost and the quality and digestibility of beans can be improved by consuming them with cereal grains. 

In this device solid-solid mixing and solid-liquid mixing processes is done separately, then the mixing food 

mixture is entered into the pellet mill, where cylindrical die is fitted inside the pellet mill to convert the 

form of the food in the duct form to beans form. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


04/04/200 

5 



(43) 



B0F 17/02, C07C 51/43 (71) 




AN IMPROVED PROCESS FOR THE PREPARATION OF ALKYL 

ESTERS AND GLYCERIN SIMULTANEOUSLY 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


EXCEL INDUSTRIES LIMITED 


184/87 SWAMI VIVEKANAND 

ROAD, JOGESHWARI (WEST), 

MUMBAI 400102, MAHARASHTRA, 

INDIA 


1. SHROFF ASHWIN CHAMPRAJ 

2. PUROHIT ABHIJIT 

PREMVALLABH 

3. OZA VEDBHUSHAN HARIBHAI 




(57) Abstract : An improved process has been disclosed for the preparation of alkyl esters by simultaneous 

transesterification of glycerides and esterification of fatty acids in the presence of an acid catalyst. The said 

process comprises mixing the raw material containing glycerides and free fatty acids, 15-35 wt% C1-4 

alcohol and 1.75 – 5.0 wt% concentrated sulfuric acid as catalyst, heating the reaction mixture to 40 – 

120˚C for 2-7 hrs., allowing the phases to separate and recovering the alkyl esters and glycerol. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 

15/04/200 

5 

(54) Title of the invention: SENSOR DEVICES 



(43) 



G01R 21/01, G01R 1/0674 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 



AVINASH SHRIKRISHNA VAIDYA 


49/39 ERANDAVANA, MAYURI 

APARTMENTS, GULMOHAR LANE, 

LAW COLLEGE ROAD, 

PUNE 411 004, MAHARASHTRA, 

INDIA 


AVINASH SHRIKRISHNA VAIDYA 




(57) Abstract : A sensor device for measuring frequency and amplitude of a varying force signal is 

provided. The sensor device comprises a sensing element defined by a plurality of even numbered planar 

segments symmetrically disposed about a central axis, a protective housing for housing, an interface 

element comprising a pick up member, a planar mechanical actuator, a transfer member adapted to receive 

varying signals from the pick up, amplify the signals picked up and transfer the amplified signals to the said 

mechanical actuator; and leads for transmitting said output signals outside the sensing device for 

processing. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


19/04/200 

5 



(43) 



C05G 3/00, C05F 17/00 (71) 




“A PROCESS FOR THE MANUFACTURE OF BFC SANJIVANI 

GRAHA VATIKA ORGANIC MANURE” (ANTI-BIOTIC) 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


MR. SHIVLALJI NAGULALJI 

BAROD 


A-1, ANJALI APARTMENT, 

NANAKHADA, SAWER ROAD, 

UJJAIN- 456 010, MADHY PRADESH, 

INDIA 


MR. SHIVLALJI NAGULALJI 

BAROD 




(57) Abstract : A process for the manufacture of BFC sanjivani Graha Vatika Organic Manure comprises 

steps of mixing, heating, decomposing and treating organic material such as Neem De Oil Cake and mineral 

to obtain the desired organic manure. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


19/04/200 

5 

(51) International A01H 1/08, CO7H, 

Classification: C12N 15/00, C12N 15/10 





(43) 


A METHOD FOR THE HUMAN LYMPHOCYTE CHROMOSOMES 

ISOLATION ASSEMBLY 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(71) 

(72) 


CHAUHAN SHIVKUMAR 

DINDAYALSINGH 


NEAR RAILWAY CABIN, 

NACHANKAR CHAWL, 

SHANTINAGAR, NAGPUR 440 002, 

MAHARASHTRA, INDIA. 


CHAUHAN SHIVKUMAR 

DINDAYALSINGH 




(57) Abstract : A method for the human lymphocyte chromosomes isolation assembly contains bottle-A of 

complete medium (containing RPMI-1640 medium, HEPES buffer, 0.2 ml / liter Gentamicin, 0.006 mg / 

liter penicillin, 0.005 mg/l streptomycin, 3 Unite / ml heparin, 0.1 ml/ 5ml phytohaemagglutinin (PHA), 2 

mg / ml sodium bicarbonate ), bottle-B of mitotic inhibitor (containing 1 mg colchicines / 10 ml of distilled 

water and 1 mg Ethidium bromide / 1 ml of distilled water ), bottle-C of 10 M solution of Phosphate buffer 

saline, bottle-D of chromosome staining solution, vial-A of hypotonic solution (containing 225 mg 

potassium chloride), vial-b of 65 mg Trypsin, vial-C containing 5 ml sterile double distilled water and 

polystyrene round bottom gamma-radiated culture tubes and literature containing detailed procedure and 

human chromosome karyotype pictures for identification and this assembly is also work for pre-natal 

chromosome isolation. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


20/04/200 

5 



(43) 


PVA BASED FILM COATING AND FILM COATING 

COMPOSITION 



C08L 29/04 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


SURESH PAREEK 



ANDHERI-KURLA ROAD, 

SAKINAKA, ANDHERI (EAST), 

MUMBAI – 400 072 


1. SURESH PAREEK 

2. CHETAN RAJSHARAD 

3. SHIVAJI KAMBLE 




(57) Abstract : A dry film coating composition for use in coating pharmaceutical tablets, nutritional 

supplements, food, confectionery forms, agricultural seeds, and the like, comprises polyvinyl alocohol self 

emulsifying glyceryl monostearate, and preferably a plasticizer such as polyethylene glycol, glycerin or 

triethyl citrate, and a pigment/opacifier. A method of coating substrates such as pharmaceutical tablets, 

nutritional supplements, food, confectionery forms, agricultural seeds, and the like, with a film coating, 

comprises the steps of mixing polyvinyl alcohol, self emulsifying glyceryl monostearate, and preferably a 

plasticizer such as polyethylene glycol, glycerin or triethyl citrate, and a pigment/opacifier into hot water to 

form an aqueous coating dispersion, applying an effective amount of said coating dispersion onto said 

substrates to form a film coating on said substrates, and drying the film coating on said substrates. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


20/04/200 

5 



(43) 



C08L 29/04, A61K 9/32 (71) 




FILM COATING COMPOSITIONS AND METHODS PROVIDING 

MOISTURE BARRIER 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


SURESH PAREEK 



ANDHERI-KURLA ROAD, 

SAKINAKA, ANDHERI (EAST), 

MUMBAI – 400 072 


1. SURESH PAREEK 

2. CHETAN RAJSHARAD 

3. SHIVAJI KAMBLE 




(57) Abstract : A dry moisture barrier film coating composition for forming a moisture barrier film coating 

for pharmaceutical tablets and the like comprises polyvinyl alcohol, self emulsifying glyceryl monostearate, 

and optionally a flow aid, a colorant, a plasticizer, a flavoring agent and/or a sweeteming agent. A liquid 

coating solution or dispersion for forming a moisture barrier film coating for pharmaceutical tablets and the 

like comprises polyvinyl alcohol, self emulsifying glyceryl monostearate, water, and optionally a flow aid, a 

colorant, a plasticizer, a flavoring agent and/or a sweetening agent. A method of coating pharmaceutical 

tablets and the like with a moisture barrier film coating comprises forming a liquid coating solution or 

dispersion for forming a moisture barrier film coating for pharmaceutical tablets and the like comprising 

polyvinyl alcohol, self emulsifying glyceryl monostearate, water, and optionally a flow aid, a colorant, a 

plasticizer, a flavoring agent and/or a sweetening agent, applying the coating solution or dispersion onto the 

tablets to form a film coating on the tablets, ad drying the film coating on the tablets. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 

21/04/200 

5 



(43) 

(54) Title of the invention: DIGIAL RADIOLOGY SYSTEM 



A61B 6/00, G01T 1/24 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 



DR. JUNED KHAN 


MAMA CHOWK, JALNA 431 203, 

MAHARASHTRA 


DR. JUNED KHAN 




(57) Abstract : The digital radiology system comprising a high-resolution monochrome CCD camera, the 

said camera coupled to a personal computer through a Pixel view TV pro xp card and the said computer 

being loaded wit suitable softwares for capturing, storing, editing and transmission of images, 

(FIG. ) : NIL 






(22) Date of filing of Application: 28/04/2005 (43) Publication Date: 


(54) Title of the invention: CLOSURE DEVICE FOR BOTTLES 



B65D 41/34 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 




The invention provides for a tamper 

indicative seal for a bottle closure 

comprising a band that has at least one slot 

on the inner surface that receives a 

projection from the bottle or closure. 

(FIG. ) : 3 


(72) 


NISHIKANT SHIRODKAR 


5, CLIFF TOWERS MOUNT MARY 

ROAD, BANDRA (WEST), 

MUMBAI 400 050. 


1. PANKAJ SAPKAL 

2. RAHUL KAUSHIK 








(22) Date of filing of Application: 28/04/2005 (43) Publication Date: 


(54) Title of the invention: WIDE ANGLE CONCENTRATING DEVICE FOR RADIATION 



F24J 2/06 (71) 



NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


PANSE SUDHIR VISHNU 


301, RAJHANS SOCIETY, 

SHREYAS COLONY, OFF AARAY 

ROAD, GOREGAON (EAST), 

MUMBAI 400 063. 


PANSE SUDHIR VISHNU 




(57) Abstract : Radiation is concentrated today with the help of curved reflectors; or curved or Fresnel lenses. 

Any such device concentrates radiation at or around its focus, if the radiation is incident parallel or nearly 

parallel to its axis. These device therefore can be called as ‘narrow angle concentrating device’ for radiation. The 

present invention is a device, which can concentrate radiation incident on it through a wide angle. 

The device is a curved reflector, having a cross-section coinciding with a ‘composite curve’, where the said 

curve has a particular geometry, comprising of section of multiplicity of parabola having different locations of 

their focal points, different focal distance and different orientations of their axes. The values of the said 

parameters are such that the said different sections of parabola flush with each other, forming a single composite 

curve. 

When the said curve is rotated through 360˚ about an axis of symmetry passing through one of its end points, 

a ‘dish type’ device is generated. When the curve is moved parallel to itself a ‘trough type’ device is generated. 

The said different sections of parabola constituting the composite curve send radiation incident along 

different angles to or around their respective foci after reflection. The integrated effect of the entire curve is that 

a fraction of radiation incident through a wide angle is reflected such that it strikes a receiver object placed in the 

region encompassing all foci. The said fraction can be made significantly large with choice of said parameters of 

the said parabola. 

A solar collector, comprising of at least one such device can concentrate beam and diffuse solar radiation 

over a large part of the day, without requiring any mechanism of solar tracking. A collector comprising of at 

least one such device can also concentrate radiation coming from any other natural or manmade source of heat, 

where the said radiation may or may not be in the form of a parallel beam. The device can also be used to 

concentrate telecommunication signals received through a wide angle from different communication satellites. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


02/05/200 

5 



(43) 



C01G 41/00, C30B 28/00 (71) 




A PROCESS FOR THE SYNTHESIS OF TYPE-II TEXTURED 

TUNGSTEN DISULFIDE THIN FILMS WITH Bi2S3 INTERLAYER 

AS TEXTURE PROMOTOR 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 


1. Dr. PATIL PRAMOD 

SHANKARARAO 

2. Mr. SADALE SHIVAJI BABASO 


THIN FILM MATERIALS 

LABORATORY, DEPARTMENT OF 

PHYSICS, SHIVAJI UNIVERSITY, 

KOLHAPUR- 416 004, 




SHANKARARAO 





(57) Abstract : A process for the synthesis of highly textured WS2 thin films on to a quartz substrate that 

comprises three steps; 

i) deposition of bismuth layer of 50nm thickness onto ultrasonically cleaned quartz substrate by thermal 

evaporation of bismuth powder, 

ii) the said bismuth layer is coated with tungsten oxide in nitrogen ambient using an intermittent spray 

pyrolysis apparatus (ISPA) by pyrolytic decomposition of ammonium tungstate solution to form a 

bilayer precursor film (BPF), 

iii) sulfurization of the said BPF in an evacuated quartz ampoule by accurately managing the thermal 

treatment wherein the said layers are treated at 850˚C for 8 hours and further at 950˚C for 18 hours, prior 

heat treatment forms an interlayer of Bi2S3m which melts during latter stage of thermal treatment, 

allowing self assembled growth of highly textured WS2, cooling the said ampoule at the rate 50˚C/hr. to 

room temperature completes the process. 

(FIG. ) : NIL 




(19) INDIA (21) 


Application: 


04/05/200 

5 



(43) 



C101G 41/00, C01B 33/035 (71) 




A PROCESS FOR THE SYNTHESIS OF EXCLUSIVELY TYPE-II 

TEXTURED TUNGSTEN DISULFIDE THIN FILMS COMPRISING 

HEXAGONAL CRYSTALLITES (2H) USING NICKEL SULFIDE 

(Ni3S2) INTERLAYER AS A TEXTURE PROMOTER 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 



SHANKARARAO 










SHANKARARAO 





(57) Abstract : A process for the synthesis of highly textured WS2 thin films onto a quartz substrate that 


I. deposition of bismuth layer of 50nm thickness onto ultrasonically cleaned quartz substrate by thermal 

evaporation of nickel powder, 

II. the said nickel layer is coated with tungsten oxide in presence of nitrogen ambient using an intermittent 

spray pyrolysis apparatus (ISPA) by pyrolytic decomposition of ammonium tungstate solution to form a 

bilayer precursor film (BPF) at 250˚C 

III. sulfurization of the said BPF in an evacuated quartz ampoule by accurately managing the thermal 

treatment wherein the said layers are treated at 800˚C for 8 hours and at 950˚C for 24 hours, prior heat 

treatment forms an interlayer of Ni3S2, with melt during latter state of thermal treatment, allowing self 

assembled growth of highly textured WS2, cooling the said ampoule at the rate of 50˚C/hr. to room 

temperature complete the process. 

(FIG. ) : NIL 




(19) INDIA (21) 

(22) Date of filing of Application: 04/05/2005 (43) 




C101G 41/00, C01B 33/035 (71) 





Publication Date: 


RHEOTAXIAL PROCESS FOR THE PREPARATION OF TYPE-II 

TEXTURED WS2 THIN FILMS HAVING POLYTYPE 3R 

STACKING OF RHOMBOHEDRAL CRYSTALLITES USING PBS 

INTERLAYER 

NIL 


(86) 


NIL 

NIL 


(61) 

(62) 



Divisional to 



(72) 



SHANKARARAO 










SHANKARARAO 





(57) Abstract : A process for the synthesis of highly textured WS2 thin films onto a quartz substrate that 


i) deposition of lead layer of 50 nm thickness onto ultrasonically cleaned quartz substrate by thermal 

evaporation of lead powder, 

ii) the said lead layer s coated with tungsten oxide in presence of nitrogen ambient using an intermittent 

spray pyrolysis apparatus (ISPA) from pyrolytic decomposition of ammonium tungstate solution to form 

a bilayer precursor film (BPF). 

iii) Sulfurization of BPF in an evacuated quartz ampoule by accurately managing the thermal treatment 

wherein the said layers are treated at 900˚C for 8 hours and at 1150˚C. for 20 hours. Prior heat treatment 

form a pbS interlayer, which melts during latter stage of thermal treatment, allowing self assembled 

growth of highly textured WS2, cooling the said ampoule at the rate of 50˚C/hr. to room temperature 

completes the process. 

(FIG. ) : NIL 



Early Publication 

The following patent applications have been published under section 11A (2) of The Patents (Amendment) Act 

2005 and rule 24A of The Patents (Amendment) Rules, 2005.. Any Person interested may file Representation 

by way of opposition to the Controller of Patents at the appropriate office against the grant of the patent in the 

prescribed manner under section 25(1) of the Patents (Amendment) Act 2005 read with the rule 55 of The 

Patents (Amendment) Rules, 2005 : ” 


(19) INDIA (21) Application No. 444/ KOL/2004 

(22) Date of filing of Application 27/07/2004 (43) Publication Date: 

(54) Title of the invention: “A HERBAL 

MEDICINE FOR CURING OR TREATING 

TUMORS/CANCER AND A METHOD FOR 

PREPARING THE SAME” 

(51) International classification: A61K 38/56 

(31) Priority Document No: 


(33) Name of priority country: 

(86) International Application No and Filing Date: 

NIL 

(87) International Publication No: NIL 

(61) Patent of addition to 

Application No: NIL 

filed on: NIL 



filed on: NIL 

(57) Abstract: 

(71) Name of Applicant: SWAPAN KUMAR 

CHATTERJEE 

Address of the Applicant: 76,M.M. GHOSH 

LANE,PATRAMARKET,KRISHNAGAR,NADIA- 

741101,WEST BENGAL,INDIA 

(72) Name of the Inventor: 

1. SWAPAN KUMAR CHATTERJEE 

Filed U/S 5(2) before The Patents 

(Amendment) Ordinance,2004 : YES 


______________________________________________________________ 


(19) INDIA (21) Application No. 660/KOL/2004 A 

(22) Date of filing of Application 23/07/2004 (43) Publication Date: 24/06/2005 

(54) Title of the invention: “PROCESS FOR 

PREPARATION OF MILK BASED HERBAL 

SWEETS” 

(51) International classification: A23C 3/00 





(87) International Publication No: 



filed on: NIL 



filed on: NIL 


(71) Name of Applicant: RABINDRA 

KUMAR PAUL 

Address of the Applicant: HINDUSTAN 

SWEETS,87/2, IBRAHIMPUR 

ROAD,JADAVPUR,KOLKATA-700 

032,INDIA 


1 RABINDRA KUMAR PAUL 

Filed U/S 5(2) before The Patents (Amendment) 

Ordinance,2004 : NO 


Early Publication vide form –9 

The following Patent applications have been published under section 11A(2) of the Patents 

(Amendment) Act 2005 and rule 24A of the Patent (Amendment) rules, 2005. 

(21) Application No.1172/DEL/2004 A (22) Date of filing of Application:23/06/2004 

(54) Title of the invention: “PRESSURE PROTECTION VALVE.” 

(51) International Classification 7 : F16K 

(30) Priority Data: NA 

(31) Document No.: NA 

(32) Date: NA 

(33) Name of convention country: NA 

(61) Patent of addition to application No.: NA 

(62) Filed on: NA 

(63) Divisional to Application No.: NA 


Total No Of Pages: 12 

(71) Name of the applicant: 

RAKESH JAIN, 


45, Vir Nagar Jain Colony , Near R.P.Bagh 

Delhi-110007. 


RAKESH JAIN. 


The present invention relates to a pressure protection valve which limits the output pressure of a fluid to a 

maximum of the preset value, irrespective of the input fluid pressure, the said valve comprising outer main 

body; a spring side cover on the left side of the diaphragm fixed to the main body; an input port which is made 

out of brass/gunmetal mounted on the main body using rubber gasket; an output port made out of brass 

gunmetal mounted on the main body using rubber gasket which is a free flowing port having a means for 

connecting to the main body and a rubber diaphragm fixed to the open side of the main body, wherein said 

diaphragm having means for controlling the flow of fluid at the input port, the said rubber diaphragm having 

a flexible center which move the said means to open or close the port. 


Early Publication vide form –9 

(21) Application No.2565/DEL/2004 A (22) Date of filing of Application:27/12/2004 

(54) Title of the invention: “PIPE UNIT ASSEMBLY FOR DOMESTIC WATER HEATER.” 

(51) International Classification 7 : F25B 40/06 



(32) Date: NA 




(63) Divisional to Application No. NA 




RAKESH JAIN 



Delhi-110007. 


RAKESH JAIN. 


The present invention provides a pipe unit assembly of a domestic water heater system which is made up of a 

thermoplastic material using injection moulding technique. The main advantage of this unit assembly is that the unit 

assembly is free from any wielding, corrosion, coating with nickel/chrome. This unit assembly resulting in faster 

production of domestic heater and improve thermal insulation of the water heater. 

(21) Application No.1171/DEL/2004 A (22) Date of filing of Application:23/06/2004 

(54) Title of the invention: “DOMESTIC WATER HEATER.” 

(51) International Classification 7 : F28D7/02 



(32) Date: NA 







(71) Name of the applicant: RAKESH 

JAIN 



Delhi-110007. 


RAKESH JAIN. 


The present invention relates to novel domestic water heater assembly wherein , the water storing container along 

with water flow ports and heater mount is made of thermoplastic material such as polycarbonate, polypheniloxide or 

their modified polymers and whole of this assembly is protected from excess inlet water pressure using a Pressure 

Protection Valve. 


(21) Application No.949/DEL/2005 A (22) Date of filing of Application:15/04/2005 

(54) Title of the invention: “MEDICINAL COMPOSITION FOR CURE OF DIABETES.” 

(51) International Classification 7 : A61K35/78 



(32) Date: NA 






Total No Of Pages: 06 


SURESH SHARMA, 


69/318 , Veer Tejaji Road, Mansarover, Jaipur, 

Rajasthan. 


SURESH SHARMA. 


Medicinal composition for cure of Diabetes containing cadambine and dihydrocinchonine, which comprises:- 

Cadambine and Dihydrocinchonine in ratio of 2:3. 

(21) Application No.1617/DEL/2005 A (22) Date of filing of Application:22/07/2005 

(54) Title of the invention: “AN IMPROVED METHOD OF PRODUCING QUALITY 

SUGAR BY WAY OF CERTAIN PARAMETERS.” 

(51) International Classification 7 : C05F5/00 



(32) Date: NA 








HARENDRA KUMAR JAIN, 


60, Bahubali Enclave, Karkardooma, 

Delhi-92. 


HARENDRA KUMAR JAIN. 


A process of sugar manufacture to make better quality sugar, in which C-fore magmas are made by B. heavy 

or C-light molasses. It is only because to reduce load of stem in the process after doing all this much 

recalculation of colouring matter in this system. 


“Publication after 18 Months 

The following Patent Applications have been published under Section 11A (3) of The Patents (Amendment) Act, 

2005. Any Person interested may file Representation by way of opposition to the Controller of Patents at the 

appropriate office against the grant of the patent in the prescribed manner under section 25(1) of the The 

Patents (Amendment) Act, 2005 read with the rule 55 of The Patents (Amendment) Rules, 2005 :” 


(19) INDIA (21) Application No:1002/MUM/2001 A 

(22) Date of filing of Application 

:12/10/2001 

(43) Publication Date: 24/06/2005 24/06/2005 

(54) Title of the invention: DETERGENT COMPOSITION WITH BENEFIT AGENTS 

(51) International Classification: C 11 D 17/00 , 

C 11 D 3/14, C 11 D 3/37. 

(31) Priority Document No. : NIL 

(32) Priority Date : 

(33) Name of priority country : 

(86) 

NIL 

NIL 

International Application : NIL 

No. and Filing Date : 

NIL 

(87) International : 

Publication No. 

NIL 


Application No. : NIL 

Filed on N.A. 

(62) 

Divisional to 


Filed on : N.A. 


( Figure: NIL ) 

Total Pages : 48 

(71) 

(72) 


HINDUSTAN LIVER LIMITED 


HINDUSTAN LIVER HOUSE, 165/166, 

BACKBAY RECLAMATION, 

MUMBAI –400 020, 

MAHARASHTRA, 

INDIA. 


1. RAGHAVACHARI RAJAN 

2. GOEL SATISH KUMAR 

3. PAVAN RAJA MANURI 

VENKATA 

4. MALTESH CHIDAMBARM 




a) From 0.5% to 70% by weight of a detergent active; 

b) From 5% TO 75% by weight of an inorganic filler; and 

c) A shear thinning, associative polymer selected from hydrophobic alkoxylated acrylic 

polymers, hydrophobic alkoxylated urethane polymers and mixture thereof. 




(22) Date of filing of Application : 17/10/2001 (43) Publication Date: 24/06/2005 

(54) Title of the invention: A STAIRCASE CLIMBING MECHANISM. 

(51) International Classification: 

B 62 B 3/00, B 66 D 1/00, B 66 B 23/00 




(86) 

NIL 

NIL 





(61) 

(62) 

NIL 

NIL 

Patent of addition to 


Filed on N.A. 

Divisional to 



(57) Abstract : A staircase climbing mechanism 

having a continuous ramp referred to as the 

overturning track, characterised in that the said 

overturning track having a shape of a rectangular 

frame whose shorter sides have been made semicircular 

and the structure has been given a depth. 

The overturning track is having a toothed inner 

surface and the outer surface is covered by 

serrated rubber to provide necessary grip to the 

overturning track. A toothed sprocketed wheel 

inside the overturning track is such that the 

toothed inner surface of the said overturning track 

is in mesh with the sprocketed wheel keeping the 

(71) 

(72) 


SOMNATH BISWAS 


C/O. DR. (COL.) S. K. BISWAS, 

C-3/1, OXFORD COMFORT, 

SALUNKHE VIHAR ROAD, 

WANOWRIE, PUNE – 411 040, 



- IDEM - 




( Figure: 02 ) 

said overturning track rotating, side plates are provided on either side of the said wheel to prevent any lateral 

movement of the said wheel. The sprocketed wheel is connected to a driving shaft and the driving shaft in 

turn is connected to the object to be mounted on the said staircase climbing mechanism. 

Total Pages : 13. 



(19) 

INDIA (21) Application No: 1028/MUM/2001 A 

(22) Date of filing of Application : 

22/10/2001 


(51) International Classification: G 01 N 27/26 (71) 




(86) 


A PROCESS FOR IN SITU PREPARATION OF ELECTROLYTE 

FOR MEASURING HYDROGEN IN HIGH TEMPERATURE 

FLUIDS. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(72) 


DEPARTMENT OF ATOMIC ENERGY 


GOVT. OF INDIA, 

ANUSHAKTI BHAVAN, 

CHATRAPATHI SHIVAJI MAHARAJ 

MARG, MUMBAI – 400 001, 



1. RAGHAVACHARY SRIDHARAN 

2. THIAGARAJAN GNANASEKARAN 

3. GOVINDASWAMI PERIASWAMI 

4. KHANDHALU HARI MAHENDRAN 

5. SUBRAMANIUM NAGARAJ 




(57) Abstract : An electrolyte for measuring hydrogen in high temperature fluids which comprises a mixture 

of MCl2 ( where M represents Ca or Sr ), LiCl and M’H2 (where M’ represents Ca2 or Sr) or LiH. Preferably 

the mixture consists of 70 (±2) mol % LiCl, 13(±2) MOL% CaHCl or SrHCl, 17(±2) moi% CaCl2 or SrCl2). 

Specifically the mixture consists of 70 mol% LiCl, 16 mo1% CaCl2, 14 mol% CaHCl. 





(19) 

INDIA (21) Application No:1029/MUM/2001 A 


:22/10/2001 


(51) International Classification: G 01 N 17/00 




(86) 


A MEASURING SYSTEM FOR ON-LINE MEASUREMENT OF 

CORROSION RATE OF METLS IN AN AQUEOUS MEDIUM. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


DEPARTMENT OF ATOMIC ENERGY 


ANUSHAKTI BHAVAN, 

CHATRAPATI SHIVAJI MAHARAJ 

MARG, 

MUMBAI 4000 39, 

INDIA. 


1. CHERUVARY RAMESH 

2. NACHIMUTHU MURUGESAN 

3. DR. SANKARALILNGAM 

VELMURUGAN 

4. AMLADOSS ANTONY 

MICHAEL PRINCE 

5. DR. VEDARAMAN GANESAN 

6. DR.SECILLIMEDU VEERVALLI 

NARASIMHAN. 




(57) Abstract : A measurement system for on-line measurement of corrosion rate of metals in aqueous 

medium, The device having a hydrogen doped argon source being connected through a mass flow controller 

for controlling the flow of hydrogen doped argon to a mixing chamber and an argon source being connected 

through a mass flow controller for controlling the flow or argon to the said mixing chamber, the mixing 

chamber being connected to a reaction chamber for receiving the mixed gas from the mixing chamber a 

hydrogen sensor being connected to the reaction chamber for continuously monitoring and measuring the 

hydrogen evolved in the reaction chamber and the output of the on chamber being connected to a metter for 

measuring the corrosion rate. By the of the system the corrosion rate can be measured accruable. 





(19) 



23/10/2001 


(51) International Classification: H 01 M 6/06 (71) 




(86) 


A PROCESS TO INCREASE THE STORAGE LIFE OF 

ENVIRONMENT FRIENDLY ZINC CARBON DRY CELL. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(72) 


MATSUSHITA LAKHANPAL 

BATTERY INDIA LIMITED. 


MAKARPURA, G.I.D.C., 

VADODARA 390 010, 

GUJARAT, INDIA. 


1. SHARMA MAN MOHAN 

2. KRISHNAN BASAVASWARAN 

3. ZACHARIAH SHAJI 

4. SHAH CHIRAG UPENDRA 




(57) Abstract : A process to increase the storage life of environment friendly paste type dry cell wherein 

bismuth salt more particularly bismuth trichloride added to starch paste substituting mercury salts wherein 

bismuth trichloride forming a superficial protective coating through jellified starch paste. 





(19) 



25/10/2001 

(54) Title of the invention: COMB. 

(51) International Classification: A 45 D 24/04 




(86) 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 




(71) 

(72) 


BHARAT ARVINDBHAI SHETH 


58/60, SUTAR CHAWL, 2 ND FLOOR, 

MUMBAI – 400 002, 



- IDEM - 




(57) Abstract : A comb defined by a toothed body having a handle portion, plurality of teeth extending from 

the handle portion, apertures defined in the handle portion and at least one additional body having a plurality 

of teeth, said additional body adapted to be slidably fitted on one surface/side of the said toothed body in the 

said apertures in the handle portion and adapted to slide over the toothed body to vary the pitch between the 

comb teeth. 





(19) 



30/10/2001 


(51) International Classification: F 04 B 39/00 




(86) 


A DISCHARGE MUFFLER FOR A HERMETICALLY 

SEALED RECIPROCATING COMPRESSOR. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


KIRLOSKAR COPELAND LIMITED 


1202/1 GHOLE ROAD, 

PUNE – 411 005, 



1. KALE BHALCHANDRA 

GANPATRAO 

2. CHIKURDE RAHUL 

CHANDRAKANT 

3. KAMBLE RAHUL 

MACHCHINDRA 

4. NILAJKAR VASUDEV SHANKAR 




(57) Abstract : A discharge muffler for a hermetically sealed reciprocating compressor consisting of a 

hollow body having an inlet tube and on outlet tube, said body being internally divided by baffle plates into 

chambers having one or more perforations to lead the discharge gas through the chambers of the discharge 

muffler from the inlet tube to the outlet tube. 





(19) INDIA (21) 


Application: 

30/10/200 

1 

(43) 



(54) Title of the invention: A THREE ROLLER SUGAR CANE MILL 


Classification 

: C 13 D 1/06 (71) 


(32) Priority Date : N.A. 

(33) Name of priority country : NIL 

(86) International Application 

No. 

: N.A. 

Filing Date : NIL 

(87) International Publication 

No. 

: N.A. (72) 


Application No. 

: NIL 


(62) 


Divisional to Application 

No. 

: NIL 



GADEKAR RAMRAO SARJERAO 


3, MANTRI CORNER, 26/3 

SHIVAJINAGAR, PUNE- 411 005, 



-IDEM- 




A three roller sugar cane mill consisting of a feed roller, a top roller and a discharge roller and a trash 

plate suspended between the feed roller and the discharge roller characterized in that the feed roller and 

the top roller are circumferentially displaced with reference to the discharge roller, the axis of the feed 

roller being operatively higher than the axis of the discharge roller and the top roller bearing 

substantially gravitationally on the discharge roller, the axis of the discharge roller being angularly 

displaced by 0 to 11 degress from the vertical plane containing the axis of the top roller. 

(FIG.: NIL) 

Total Pages: 8. 



(19) 



31/10/2001 


(51) International Classification: B 01 J 2/28 




(86) 


A PROCESS FOR OBTAINING A SOLID ORGANIC 

MATERIAL OF DESIRED SHAPE AND SIZE. 

NIL 

NIL 





(61) 

(62) 

NIL 

NIL 



Filed on N.A. 

Divisional to 



(71) 

(72) 


HINDUSTAN LEVER LIMITED 


HINDUSTAN LEVER HOUSE, 

165/166, BACKBAY RECLAMATION, 

MUMBAI – 400 020, 



1. GANGOPADHYAY MANISH 

2. KUMAR VELAYUDHAN NAIR 

GOPA 




(57) Abstract : The present invention relates to a process to obtain a solid organic material of a desired 

shape by a) heating a solid organic material to a temperature that is not higher than 4 degrees centigrade 

below the melting temperature of the organic material for a specified period of time b) extruding the organic 

material c) preferably merumerising or spherodising the material to a desired shape and size. Optionally, 

other organic or inorganic materials may be added during any step of the process. 





(19) 



08/11/2001 



C 11 D 3/08, C 11 D 11/04, C 11 D 17/02, 

C 11 D 13/18, C 11 D 17/00 




(86) 


A PROCESS FOR MANUFACTURING A DETERGENT BAR 

COMPOSITION. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 




(71) 

(72) 


HINDUSTAN LEVER LIMITED. 




MUMBAI – 400 020, 



1. KRISHNA VIJAY BANGALORE 

2. SUBRAHMANIAM NARAYANAN 

3. GOEL SATISH KUMAR 




A detergent bar comprising: 

(i) from 5% to 60% preferably from 10% to 50% by weight of detergent active; and 

(ii) from 2% to 20%, preferably from 5% to 15% by weight of a structuring system being the reaction 

product of at least two different polyvalent metal ions with sodium silicate, wherein one of the metal 

ions is calcium or magnesium and the other being selected from boron, aluminum, zinc, calcium and 

magnesium. 









F 16 K 21/08, F 16 K 31/06, F 16 K 25/04, 

F 16 K 31/66, F 16 K 25/00 




(86) 

AN IMPROVED BALL VALVE FOR USE IN LIQUID 

TRANSFER PIPE LINES. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(57) Abstract : An improved ball valve device for use in 

particular in liquid transfer pipelines, the valve device 

comprising: a unitary main body (4); a two-part lateral 

body (1,2) secured to the main body (4) for defining a 

longitudinal passage with the main body (4); a ball (5) 

disposed within the passage, the ball (5) having a throughhole 

for flowably connecting the passage, the ball (5) 

having an outside surface; the ball (5) having an open 

position wherein the opening communicates with the 

passage and a closed position wherein the outside surface 

is disposed across the passage; a stud (6) secured at the 

outside surface of the ball (5) which extends outwardly 

from the main body (4). A sealess magnetic actuator is 

disposed being connected to the stud (6) for opening and 

closing of the valve and preventing simultaneously 

leakage of fluid from the valve. 


(71) 

(72) 


KWENG ALLOYS PVT. LTD. 


J-9/66, G.I.D.C., ANTALIA, 

BILIMORA – 396 325, 



1. DESAI JITENDRA DHIRAJLAL 







(19) 



15/11/2001 


(51) International Classification: F 16 J 12/00, 

F 01 B 25/14, F 17 D 3/01, F 17 D 3/18 




(86) 


A PNEUMATIC CONTROL DEVICE FOR COMPRESSING 

AIR-SUPPLIES. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


GODREJ & BOYCE MFG. CO. LTD. 


E & E SERVICES, 

PIROJSHANAGAR, VIKHROLI, 

MUMBAI – 400 079, 



1. PANDE KIRON C. 




(57) Abstract : This invention provides a pneumatic control device for compressed air supplies comprising an 

air control device which is retrofittable in an intermediate position between upstream compressors and air 

storage vessels and downstream useful production equipment or the like to provide benefits of greater airutilization 

efficiency and a better air system balance between supply and demand, especially on an air-weight 

flow basis. A preferred embodiment employs a plurality of servo-driven flow controllers in parallel between a 

pair of header tanks and controls them in response to sensed downstream pressures and to the pressure 

differential across the control device. 





(19) 



:19/11/2001 


(51) International Classification: A 61 K 7/11, 

A 61 K 7/06, A 61 K 7/48 

(31) Priority Document No. : 60/252/703 



(86) 




NON-STICKY COSMETIC MOISTURIZER FOR SKIN AND 

HAIR. 

22/11/2000 

UNITED STATES 

OF AMERICA 

{NI{ 

NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 






MUMBAI –400 020, 

MAHARASHTRA, 

INDIA. 





(57) Abstract : A non-sticky moisturizing cosmetic composition containing a relatively high level of 

humectant, such as glycerol or sorbitol, and a polymeric wetting agent. 





(19) 



:19/11/2001 

(54) Title of the invention: IMPROVED WASHING SYSTEM 

(51) International Classification: B 08 B 3/04 




(86) 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 




(71) 

(72) 




BOMBAY, POWAI, 

MUMBAI 400 076 



1. MODY KRIPA DEVAGNA 

2. BARGAJE VIJAYA MILIND 

ROBERTS GLYN 




(57) Abstract : The invention relates to a cleaning composition suitable for manually clearing substrates. The 

composition comprises at least two immiscible liquid phases having one liquid-liquid interface with an 

interfacial tension of more than 5mN/m, the difference in density between the two liquid phases being not 

more than 0.2/cc. After agitation the composition is applied to the substrate to be cleaned, and subsequently 

friction is applied to the substrate. The composition provides for the required stability after agitation, and gives 

good detergency, particularly as regards particulate soil. 







(54) Title of the invention: TOOLS FOR FINE MACHINING OF WORK PIECES. 

(51) International Classification: B 23 B 29/034, 

B 23 C 5/24 

(31) Priority Document No. : 1) 10060283.5 

2) 20103921.4 



(86) 


No. and Filing Date : NIL 



NIL 



(62) 

Filed on N.A. 

Divisional to 



1) 05/12/2000 

2) 27/02/2001 

GERMANY 

(71) 

(72) 


MAPAL FABRIK FUR 

PRAZISIONSWERKZEUGE 

DR. KRESS KG 


OBERE BAHNSTRASSE 13, 

73431 AALEN, GERMANY. 


1. DR. DIETER KRESS 




(57) Abstract : A tool for fine machining of work pieces, 

wherein the tool comprises: a body having a forward end; a 

cutter tip disposed at the forward end of the body, the cutter 

tip including a cutter edge, the cutter tip being moveable with 

respect to the body at least one of radially with respect to the 

axis of the body and axially along the axis of the body for 

correspondingly adjusting the position of the cutting edge of 

the cutter tip with respect to the body, the cutter tip having a 

side face; a setting device on the body for cooperating with 

the cutter tip for moving the cutter tip; the setting device 

comprising an adjusting element that extends over a region of 

the side face of the cutter tip and is contactable with the side 

face; a displacing element connected with the adjusting 

element for displacing the adjusting element relative to 


the cutter tip and to the body for moving the cutter tip 

and the cutting edge thereof, at least one of radially with respect to the axis of the body and axially with respect 

to the axis of the body; wherein the adjusting element has a respective adjusting surface that engages and 

interacts with and is so shaped with respect to the side face of the cutter tip that movement of the adjusting 

element and the adjusting surface moves the cutter tip at least one of axially and radially with respect to the axis 

of the body; and wherein the adjusting surface of the adjusting element has first and second bearing surfaces 

thereon which are spaced at a distance from one another with an intermediate region therebetween, and 

arranged so that the side face of the cutter tip is engaged by said first and second bearing surfaces but not by 

said intermediate region. 




(19) 



:19/11/2001 






(86) 


HIGH POWER FACTOR FUSE PROTECTED PHASE 

CONTROLLED. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(57) Abstract : A high power factor fuse protected phase 

controlled converter 

(1) comprising a rectifier bridge (2) of SCRs (T1, T2 ) and 

diodes (D2, D2 ) connected to a single phase AC supply (S2 ) 

through an input filter inductor (L1) capacitor 

(C1)configuration and fuse (F). a free wheeling diode (D3) 

and an output filter inductor (L2) and capacitor (C2) 

configuration are connected across the rectifier bridge. A load 

® is connected across the output filter capacitor. A control 

circuit 5 comprises a dual output trigger generator (6), a pulse 

width modulated signal generator (7), a voltage comparator 

(8), a triangular wave generator (9), a switching frequency 

controller (10), an error amplifier (11), a turn off trigger 

generator (12), a transistor Q1, a high frequency voltage 

transformer (XT), a pair of diodes (D4,D5), a resistance (R1) 

and diode (D6) configuration and a diode D7. V1 and V2 are 

single-phase reference AC voltage and reference DC voltage, 

respectively. 


(71) 

(72) 


INDIAN INSTI TUTE OF 

TECHNOLOGY 


BOMBAY, POWAI, 

MUMBAI 400076, 

MAHARASHTRA, 

INDIA . 


1. DR. VICTOR PRINCE 

SUNDARSINGH 

2. NARAYAN SHET. 




( Figure: 1 ) 



(19) 



:20/11/2001 


(51) International Classification:B 32 B 15/00 

(31) Priority Document No. : 2000-71864 



(86) 




A METHOD FOR MANUFACTURING A CORROSION- 

RESISTANT 

30/11/2000 

KOREA 

NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


JU-YONG JUNG 


9-906, WOOSUNG APT, # 83, DOWHA- 

DONG, MAPO-GU, 

SEOUL, REPUBLIC OF KOREA. 


-IDEM- 




(57) Abstract : Disclosed are a corrosion-resistant clad steel plate and its manufacturing method. The 

corrosion-resistant clad steel plate having excellent mechanical bonding force in heterogeneous metals can be 

manufactured by tack-welding a thin strip of Fe-or Ni –based amorphous alloy as a binder onto one side one 

side or both side of a carbon steel plate and seam- welding a corrosion-resistant metal plate such as an alloy of 

nickel or titanium onto the binder to produce a corrosion resistant clad steel plate, or alternatively, produced by 

tack-welding a thin strip of Fe-or Ni-based amorphous alloy as a first binder onto one side or both sides of a 

carbon steel plate, tack-welding a thin strip of an alloy of nickel or stainless steel and copper as a second binder 

onto the thin strip and seam-welding a corrosion –resistant metal plate such a an alloy of nickel or titanium onto 

the binder. 





(19) 



22/11/2001 


(54) Title of the invention: IMPROVED CLEANING COMPOSITION. 

(51) International Classification: C 11 D 3/00, 

C 11 D 7/00 




(86) 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 






MUMBAI – 400 020, 



1. CHATTERJEE JAIDEEP 

2. BARGAJE VIJAYA MILIND 




(57) Abstract : The invention relates to a cleaning/washing composition having a system of at least two 

liquids, which are present above their mutual miscibility limits, such that the composition is not a single 

homogenous clear phase. It specifically relates to a cleaning composition comprising: 

i. a non-polar phase comprising one or more liquids having an electric dipole moment less than that of water 

wherein at least 10% of the said non-polar phase has an electric dipole moment greater than 0.8 debye; 

ii. a polar liquid; 

wherein the non-polar and polar liquids are present at levels above their mutual miscibility limits, such that they form at 

least two immiscible phases. 





(19) 



:26/11/2001 


(51) International Classification: C 12 P 13/00 




(86) 


A PROCESS FOR THE PREPARATION OF 7- 

DIETHYLAMINO –2H –1-BENZOPYRAN-2-OXO-3(N- 

SUBSTITUTED) -CARBOXAMIDES 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


STRIDES ARCOLAB LTD. 


21, DEVAVRATA, SECTOR 17, 

VASHI, 

NAVI MUMBAI –400 703. 


1 . AKBARALI, P.M. 

2 . VIJAY RAJ, K.K. 




(57) Abstract: A process for preparation of 7-diethylamino-2H-1-benzopyran-2-oxo-3-(N-substituted)carboxamides 

by refluxing 4 – diethylamino salicylaldehyde and malonic ester of aromatic amines in methanol 

containing catalytic amount of piperidine. 





(19) 



26/11/2001 


(51) International Classification: C 07 C 15/00 (71) 




(86) 


NOVEL PROCESS FOR THE PREPARATION OF 

TRIS (2,4-DI TERT BUTYL PHENYL) PHOSPHITE. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(72) 


STRIDES ARCOLAB LTD. 


201, DEVAVRATA, SECTOR 17, 

VASHI, NAVI MUMBAI – 400 0703, 



1. AKBARALI P. M. 

2. VIJAY RAJ K. K. 

3. T. GOUDA KARABASANA 




(57) Abstract : Disclosed is a novel process for the preparation of tris (2,4-di tert butyl phenyl) phosphite 

comprising reacting a mixture of 2,4-di tert phenol (1.94 moles) and pyridine (1.94 moles) in presence of 

Methylene Dichloride with PCl3 (0.64 moles), by adding PCl3 in drops at 0-5ºC in nitrogen atmosphere over a 

period of one hour; distilling out the residue Methylene Dichloride; adding Iso-propanol and filtering out the 

white crystalline precipitate; and washing the resultant product with cold water. 





(19) 



27/11/2001 


(51) International Classification: C 11 D 39/00 (71) 




(86) 


A PROCESS FOR THE MANUFACTURE OF A DETERGENT 

BAR. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(72) 






MUMBAI – 400 020, 



1. KAPOOR BIR 

2. MAHAPATRA SAMIRAN 

3. MURTHY KAMSU 

VENKATASATYANARAYANA 




(57) Abstract : The invention concerns solid shaped detergent compositions comprising 0.5 – 95% by weight detergent 

active and 0-90% by weight of inorganic particulates and/or other conventional ingredients and wherein the external 

surface of said shaped detergent composition comprises at least one polymer film obtained by radiation curing or a 

radiation-curable resin composition. 







29/11/2001 


(51) International Classification: B 61 L 27/00 




(86) 


A SYSTEM FOR CONTROLLING THE MOVEMENT OF 

TRAINS ON TRACKS THROUGH STATIONS. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


KONKAN RAILWAY 

CORPORATION LIMITED 


BELAPUR BHAVAN, 

SECTOR 11, CBD BELAPUR, 

NAVI MUMBAI – 400 614, 



1. BOJJI RAJARAM 




(57) Abstract : A system for controlling the movement of trains on tracks through stations; 

[i] A station controller located in a station building associated with each of the stations, 

[ii] at least two Interlocking Controllers (IC) located at either end of the station and connected to the said 

station controller, using a system architecture as herein described; 

[iii] electronic point machines located at either end of the station; 

[iv] a local area network connected between the station controller and the interlocking controller for permitting 

two way data communication between the station controller and the inter locking controller; 

[v] track circuits associated with each of the tracks passing through the station and the yard associated with the 

station; 

[vi] a Computer based console connected to the station controller for Man Machine Interaction (MMI); 

[vii] an Automatic Driving Device (ADD) mounted in a train, adapted to interact with the station controller said 

automatic driving device being hardwired to the said track circuits; 

[viii] a wire network for connecting the interlocking controllers track circuits and the said electric points at each 

end of the Station; and 

[ix] a wireless data link for two way communication between the automatic driving devices and the interlocking 

controllers. 





(19) 



04/12/2001 


(51) International Classification: B 65 B 23/12 




(86) 


APPARATUS FOR TRANSFERRING BATCHES IN 

PREDETERMINED COUNT OR LENGTH OF LAMINAR 

ARTICLES STANDING ON EDGE. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


PARLE PRODUCTS PRIVATE 

LIMITED. 


NORTH LEVEL CORSSING, 

VILE PARLE (EAST), 

MUMBAI – 400 057, 



1. CHAUHAN VIJAY 




(57) Abstract : An apparatus and method for forming batches in predetermined count or length of laminar 

articles standing on edge for transfer from multiple supply lines/chutes to a common delivery line is 

disclosed. The common delivery line is located operatively below the supply lines/chutes. The axis of 

movement of the common delivery line is perpendicular to the axes of movement of the supply lines/chutes. 

The apparatus includes a horizontal platform on which the laminar articles, such as biscuits are led from the 

supply lines/chutes, pusher bars operating simultaneously for each of the arrays of laminar articles emanating 

form the supply lines/chutes on to the platform. The batch of articles displaced from the arrays are pushed 

towards striker plates adjacent to hatches in the platform. The batch of laminar articles strike the striker 

plate, align themselves and rebound from the striker plate without deformation and drop through the hatches 

in the platform to pockets in the common delivery line below. 






(22) Date of filing of Application : 07/12/2001 (43) Publication Date: 


(54) Title of the invention: A SELF SETTING VERTICAL FLOUR MILL. 

(51) International Classification: A 47 J 43/04, 

B 02 C 13/00 




(86) 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


ROHITBHAI JASHBHAI PATEL 


20 GIDC ESTATE, 

VITHAL UDYOGNAGAR, 

388121, DISTRICT ANAND, 



- IDEM - 




(57) Abstract : A self setting vertical flour mill (1) comprising a rotary grinding stone (3) fitted with a 

reinforcing frame (7) at the back side thereof and mounted on a sleeve member (41) which is detachably, 

axially movably and radially non-rotatably engaged over the inner end (49) of the mill shaft (11). The outer 

end (61) in the front cover (51) fitted at the front side of the mill housing (4). A self setting mechanism (63) 

comprising a ball bearing (64) is axially movably located in a casing (65) fitted to the front cover and stressed 

by a compression spring (67). The outer end of the sleeve member is fixed in the ball bearing. A sealing 

gasket (68a) is disposed in the clearance between the sleeve member and front cover and fixed to the front 

cover. 

( Figure: 3 and 4 ) 




(19) 



12/12/2001 


(54) Title of the invention: A NOVEL WEARABLE DISPLAY DEVICE. 

(51) International Classification: G 09 F 19/00 




(86) 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


SHAAN ANAND ZAVERI 


SURAJ FARM – 352, HANSOL, 

AHMEDABAD – 382475, 

GUJARAT STATE, INDIA. 


- IDEM - 




(57) Abstract : A novel wearable display device comprises of a flat panel made of corrugated cardboard or 

optional material cut in a particular shape such as the shape of the enlarged hand showing in fig. 4, 5, 6, 7 

and 8, optionally with image and/or text being applied on one or both sides of the flat panel for the purpose 

of signage, communication or advertisement. One or more elastic straps are provided by attaching their ends 

to one side of the flat panel so as to create a space between the flat panel and the straps through which a hand 

can be inserted allowing the display device to be worn on the hand and held in position, so that by raising the 

hand on which the device is worn, the wearer can conveniently and prominently exhibit the display device. 





(19) 



13/12/2001 


(54) Title of the invention: A BUILT LAUNDRY DETERGENT COMPOSITION. 


C 11 D 1/14 

(31) Priority Document No. : 0030671.2 


15/12/2000 

(33) Name of priority country : UNITED 

KINGDOM 

(86) International Application : NIL 


NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 






MUMBAI – 400 020, 



1. BLYTHING SANDRA ANN 

2. SINGH AMRAT PAUL 

3. TITLEY THELMA CHRISTINE 




(57) Abstract : A built laundry detergent composition contains anionic surfactant in combination with a 

minor amount of a highly ethoxylated nonionic surfactant which is a C8-C16 alcohol ethoxylated which an 

average of from 20 to 50 ethylene oxide groups. The composition exhibits improved oily soil detergency 

especially under hard water conditions. 





(19) 



13/12/2001 

(54) Title of the invention: DETERGENT COMPOSITIONS. 


C 11 D 1/14, C 11 D 1/62, C 11 D 1/72 




(86) 



15/12/2000 

UNITED 

KINGDOM 

NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 




(71) 

(72) 






MUMBAI – 400 020, 



1. SINGH AMRAT PAUL 

2. THORLEY DAVID 

CHRISTOPHER 




(57) Abstract : A built laundry detergent composition contains a combination of anionic, nonionic and 

cationic surfactants which includes a highly ethoxylated nonionic surfactant which is a C8-C16 alcohol 

ethoxylated which an average of from 20 to 50 ethylene oxide groups. The cationic surfactant may 

advantageously be an ethoxylated quaternary ammonium compound. The composition exhibits improved 

oily soil detergency. 





(19) 



14/12/2001 


(51) International Classification: A 61 K 31/7115 




(86) 


A METHOD OF PRODUCING A COSMETIC SYSTEM / 

FORMULATION. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 






MUMBAI – 400 020, 



1. BHASKAR JAMES PRABHANAND 

2. RAMAN GOVINDARAJAN 

3. SHARMA KIRTI 

4. VINOTH KUMAR KUTTI 

RAGUNATH 

5. DHARMALINGAM 

KUPPAMUTHU 




(57) Abstract : The present invention relates to development of system/formulation to protect skin from 

ultraviolet radiation (UVR) exposed damage, anti-ageing as well as controlling skin colour by differentially 

regulating genes responsible for such behaviour changes on exposure to UV. The invention also relates to 

identification and synthesis of novel genes for use in such system/formulation to control/monitor the above 

said skin conditions. 





(19) 



14/12/2001 


(51) International Classification: A 61 K 31/7115 




(86) 


COSMETIC SYSTEM/FORMULATION COMPRISING 

NUCLEOTIDE AND/OR TRANSLATED AMINO ACID 

SEQUENCE ACTIVES. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 






MUMBAI – 400 020, 



1. BHASKAR JAMES PRABHANAND 

2. RAMAN GOVINDARAJAN 

3. SHARMA KIRTI 

4. VINOTH KUMAR KUTTI 

RAGUNATH 

5. DHARMALINGAM 

KUPPAMUTHU 




(57) Abstract : The present invention relates to development of system/formulation to protect skin from 

ultraviolet radiation (UVR) exposed damage, anti-ageing as well as controlling skin colour by differentially 

regulating genes responsible for such behaviour changes on exposure to UV. The invention also relates to 

identification and synthesis of novel genes for use in such system/formulation to control/monitor the above 

said skin conditions. The invention further relates to method of treating skin conditions based on 

identification of genes differentially regulated by exposure to UVR based on identification of skin conditions 

based on states of such differentially regulated genes. 





(19) 



20/12/2001 


(51) International Classification: D 06 L 3/16, 

D 01 G 9/00 




(86) 


A SINGLE STAGE PROCESS FOR THE PREPARATION OF 

ABSORBENT COTTON FROM SHORT STAPLE FIBRE 

WASTE. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


THE CENTRAL INSTITUTE FOR 

RESEARCH ON COTTON 

TECHNOLOGY 


ADENWALA ROAD, MATUNGA, 

MUMBAI – 400 019, 



1. NACHANE RAJAN 

PANDHARINATH 

2. NAGARKAR RAVI DADURAM 




(57) Abstract : A new single stage process for the preparation of absorbent cotton from short staple cotton fibre waste by 

using a single stage scouring and bleaching process using 0.1% to 1.5% NaOH and 0.05% to 0.4% of a bleaching agent in 

an open vessel at a material to liquor ratio of 1:30, soaking the material and washing it with hot and cold water followed 

by neutralization in 0.1% acetic acid. 






(22) Date of filing of Application : 21/12/2001 (43) Publication Date: 


Post Dated to 30/05/2002 



A 61 K 9/72, A 61 K 45/00, A 61 P 37/08 




(86) 

A PROCESS OF PREPARING LORATADINE NASAL SPRAY 

SOLUTION. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


ALEMBIC LIMITED 


ALEMBIC ROAD, 

VADODARA – 390 003, 



1. BHATTACHARYA SAMPAD 

2. LAGU KIRAN 




(57) Abstract : The process of preparing loratadine nasal spray solution comprises the following steps: 

i) adding loratidine 0.4% to 0.5% w/v in sufficient quantity of purified water under stirring to make 

a slurry and adding Hydrochloric acid 1M solution for dissolving and forming a clear solution of 

loratadine; 

ii) adding Glycerin 0.5% to 10% w/v, Propylene glycol 0.1% to 50% w/v and Polyoxyl-35 castor oil 

0.1% to 50% w/v to the clear solution of loratadine and stirring to form a homogenous solution; 

iii) dissolving Disodium edetate 0.025% to 0.3% w/v in purified water and adding Phenyl ethyl 

alcohol 0.1% to 0.3% w/v and 50% Benzalkonium chloride solution 0.001% to 0.04% w/v and 

stirring to form solution and mixing the said solution to the homogenous solution of the above 

step (ii); 

iv) preparing a 5% w/v solution of Sodium Hydroxide in purified water; 

v) adjusting the pH of homogenous solution of the above step (iii) in the range of 4 to 7 by using 

Sodium Hydroxide solution of the above step (iv); 

vi) making up the desired volume by adding desired quantity of purified water and stirring; 

vii) filtering the solution of the above step (vi) and filtering it in the containers as per requirement. 





(19) 



:24/12/2001 


(54) Title of the invention: A PARTICULATE DETERGENT COMPOSITIONS. 

(51) International Classification: C 11 D 1/65 




(86) 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


HINDUSTAN LIVER LIMITED. 




MUMBAI –400 020, 

MAHARASHTRA, 

INDIA. 


1. METCALFE KENNETH 

2. MOLE VINCENT CHARLES 




(57) Abstract: A detergent composition comprising 

a) More than 40% by weight to 95% by weight of anionic surfactant. 

b) From 0.1% to 10%, preferably form 0.5% to 5% by weight of cationic surfactant and 

c) The balance being other component. 

Said composition comprising from 35% to 95%, preferably from 45%to 95%, more preferably from 

55%to 95% by weight of the total composition of calcium tolerant surfactant.` 





(19) 





(54) Title of the invention: LAUNDRY DETERGENT COMPOSITIONS. 

(51) International Classification: C 11 D 1/65 

(31) Priority Document No. : 0031823.8 



(86) 



29/12/2000 

UNITED 

KINGDOM 

NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 






MUMBAI – 400 020, 




2. MOLE VINCENT CHARLES 




(57) Abstract : A laundry detergent composition comprising (a) at least 5 wt% of a calcium-tolerant non-soap 

anionic surfactant system comprising an alpha-olefin sulphonate and alkyl ether sulphate; (b) at least 0.1% of a 

cationic surfactant system in a weight ratio of (a) : (b) from 3:1 to 1:1 and the balance, if any, being other 

minor ingredients. 





(19) 





(54) Title of the invention: LAUNDRY DETERGENT COMPOSITIONS. 


C 11 D 3/06, C 11 D 3/12, C 11 D 3/08 




(86) 



29/12/2000 

UNITED 

KINGDOM 

NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 






MUMBAI – 400 020, 



1. VAN DER HOEVEN PHILIPPUS 

CORNELIS 





(57) Abstract : A power laundry detergent composition comprising (a) more than 10wt% of a calcium tolerant 

anionic surfactant system; (b) from 0.1% to 10%, preferably from 0.5% to 10%, more preferably from 1% to 

10% by weight of a strong builder system selected from phosphate builders and aluminosilicate builder and 

mixtures thereof; and (c) the balance, if any, being other detergent ingredients wherein said composition 

comprises less than 35wt%, preferably less than 25wt%, more preferably less than 15wt% of non-functional 

non-alkaline water soluble inorganic salt. 





(19) 



27/12/2001 


(51) International Classification: A 23 L 1/308 




(86) 


PROCESS FOR THE PREPARATION OF A COMPOSITION 

CONTAINING PSYLLIUM HUSK. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 

Name of the Application: 

CADILA HEALTHCARE LTD 

Address of the Application: 

1956, OF ZYDUS TOWER, 

SATLLITE CROSS ROADS, 

AHEMADABAD 380 015, 



1. TADURI VEERABABU 

2. GEMBALI SEETARAJU 

3. BELAPURE SHIRISH G. 



Ordinance, 2004 : NO 

(57) Abstract : A process for the preparation of a composition containing Psyllium husk in the form of a multilayered 

creamy, crunchy, highly palatable biscuits which comprises preparing wheat flour slurry, preparing creamy inner layer 

containing the Psyllium husk, preparing crispy wheat flour sheets from said wheat flour slurry, and preparing creamy 

wafers with said crispy wheat flour sheets, with said creamy inner layer containing the Psyllium husk between said sheets, 

wherein said Psyllium is present at a concentration in the range of 20- 80% by weight of the total composition and said 

wheat flour is present at a concentration in the range of 30- 60% by weight of the total composition. 





(19) 



:28/12/2001 


(51) International Classification: E 04 B 2/00 

E 04 B 2/00 




(86) 


PREFABRICATED REINFORCED CEMENT CONCRETE 

WALL AND A METHOD OF CONSTRUCTION THEREOF 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(71) 

(72) 


NAHALCHAND LALOOCHAND 

PLRIVATE LIMITED. 


KANTILAL HOUSE, 14, 

MAMA PARMANAND MARG, 

MUMBAI 400 004, 

MAHARASHTRA 


1. SHRI RAJESH HIMATLAL 

2. SHRI MUKESH HIMATLAL 

3. SHRI RRAKASH VASUDEO PARAB 

4. SHRI NANDKUMAR DEORAM 

PATIL 




(57) Abstract: The present invention relates to a method of constructing a pre-fabricated reinforced cement 

concrete wall comprising of (a) constructing a horizontal formwork with a provision to incline it, (b) providing 

one or more reinforcing bars within the said formwork, (c) pouring concrete in the said formwork, (d) setting 

the concrete (e) inclining the wall along with formwork, and (f) removing the formwork and an one-piece prefabricated 

reinforced cement concrete wall having thickness of 150 mm or less provided with concealed 

services like electrical, plumbing, communication, gas, etc. 





(19) 

INDIA (21) Application No: 1224/MUM/2001 A 


28/12/2001 


(51) International Classification: C 12 M 1/02 (71) 




(86) 


AN IMPROVED APPARATUS AND A PROCESS FOR 

GENERATION OF BIOGAS USING ANAEROBIC DIGESTION. 

NIL 

NIL 



NIL 



NIL 



Filed on N.A. 

(62) 

Divisional to 



(72) 


LARS ENVIRO PVT. LTD. 


218, BAJAJ NAGAR, 

SOUTH AMBAZARI ROAD, 

NAGPUR – 440 010, 



1. RUKMANG PRASHANT 

2. DARYAPURKAR RAMESH 




(57) Abstract : An improved anaerobic Digester Plant for generation of biogas comprising of a heat exchanger or cooling 

sump (1) for the conversion of waste water from industries brought by open channel or pipeline into biogas having a 

buffer sump (2) connected in tandem by conduit for maintenance of pH in acidic level which maintaining the temperature 

of contents of buffer tank from 35 to 42 ºC which is supplied to the digester (4) through the feed pump (3), the said 

digester comprising of a tank with top open for the introduction of a central feed pipe/column (5); a central agitator mixer 

(6) is housed in the central feed pipe for the agitating/mixing of waste water, returned sludge and digester content through 

the port provided at the top of the central feed pipe; plurality of lateral mixer (7) are provided near the bottom to ensure 

proper mixing, sludges scouring of digester bottom; and said digester is provided a over flow weir for the digester content 

taken to degassifier (8); the dissolved biogas from the treated waste water escapes to atmosphere; the degasified waste 

water then conveyed to parallel plate separator (9) where the sludge settles; the settled sludge is recycled in the digester or 

waste using recycle pump (10); the biogas generated in the digester is then taken to gasholder (11) which allows the 

pressure regulation in digester and flow regulation for its outward conveyance the excess biogas is pass through 

emergency release to the flare stack (12); the generated biogas is taken to biogas utilization unit through suitable biogas 

blower (13). 





(19) INDIA (21) Application No.: IN/PCT/2002/00289/MUM A 

(22) Date of filing of Application: 08/05/2002 (43) Publication Date: 24/06/2005 

(54) Title of the invention: : A METHOD FOR DETERMINING A FOCUS VALUE IN AN IMAGE 

(51) International classification : H04N 5/232 

(31) Priority Document No : 09/383,117 

(32) Priority Date : 25/08/1999 

(33) Name of priority country : USA 


No and Filing Date: 


No 


Application No 

: PCT/US00/22128 

11/08/2000 

: WO 01/15434 A1 

: 

NIL 


(62) Divisional to Application 

No 

: NIL 


(57) Abstract: A method for determining a focus value in an 

image, including selecting an area of interest in the image and a 

color plane of interest. Then, filtering the color plane of interest 

within the area of interest to produce a filtered region; and, 

determining the mean absolute value of the filtered region. A 

system for implementing the method is also disclosed. 


(71) Name of Applicant: 

INTEL CORPORATION 


DELAWARE CORPORATION, 2200 

MISSION COLLEGE BOULEVARD, 

SANTA CLARA, CALIFORNIA 95052, 

USA. 


1. YAP-PENG TAN 

2. BRENT THOMAS 

3. TINKU ACHARYA 

Filed U/S 5(2) before The 



(FIG.- 1.) 





(54) Title of the invention: : A METHOD OF CONSTRUCTING AN ELECTRONIC ASSEMBLY 

(51) International classification : H01L 23/34 


(32) Priority Date : 13/09/1999 





No 



: PCT/US00/23778 

29/08/2000 

: WO 01/20673 A1 

: 

NIL 



No 

: NIL 





DELAWARE CORPORATION, 2200 

MISSION COLLEGE BOULEVARD, 

SANTA CLARA, CALIFORNIA 95052, 

USA. 


1. DISHONGH TERRANCE J. 

2. CHURILLA PAUL W. 

3. PULLEN DAVID H. 




(57) Abstract: According to one aspect of the invention a method of constructing an electronic assembly is provided. The 

electronic assembly is constructed from a semiconductor package including a package substrate and a semiconductor chip 

mounted to the package substrate, a thermally conductive member, and a substance including indium. The method comprises 

securing the thermally conductive member and the semiconductor pakage in a selected orientation relative to one another 

with the thermally conductive member on a side of the semiconductor chip opposing the package substrate and with the 

substance located between the semiconductor chip and at least a portion of the thermally conductive member. The substance 

is thermally coupled to the semiconductor chip on one side and thermally coupled to the portion of the thermally conductive 

member on an opposing side. 


(FIG.- 11.) 





(54) Title of the invention: : A BLOCK HOLDER FOR A BOGIE BRAKE 

(51) International classification : B61H 1/00 

(31) Priority Document No : 9904185-7 

(32) Priority Date : 18/11/1999 

(33) Name of priority country : SWEDEN 




No 



: NIL 



No 

: PCT/SE00/02246 

16/11/2000 

: WO 01/36247 A1 

: NIL 


(57) Abstract: A rail vehicle bogie brake has a brake beam (4, 5), 

which at its end is provided with a brake block holder (8) having a 

brake block (9) for brake application against a tread of a wheel. The 

brake block holder has a transverse cylinder (19) for its pivotable 

connection with the brake beam. A mounting shaft (14) is attached 

in the end of the brake beam and is provided with a sleeve (16). The 

sleeve engages the mounting shaft and has an outer diameter 

corresponding to the inner diameter of the cylinder. A sleeve plate 

(17) is held against the sleeve, which is slightly longer than the 

cylinder, by means of screws (18) attached in the mounting shaft and 

prestressing the sleeve. 



SAB WABCO AB 


BOX 515, SE-261 24 LANDSKRONA, 

SWEDEN. 


1. EMILSSON FRED 

2. NYMAN JOHAN 




(FIG.- 3.) 



(19) INDIA (21) Application No.: 486/MUMNP/2003 A 


(54) Title of the invention: : FULL-FASHIONED GARMENT WITH SLEEVES HAVING 

INTELLIGENCE CAPABILITY 

(51) International classification : D03D 3/02 


(32) Priority Date : 14/11/2000 





No 



: PCT/US01/43968 

14/11/2001 

: WO 02/040756 A3 

: 

NIL 



No 

: NIL 


(57) Abstract: The invention comprises a full-fashioned 

weaving process for the production of a woven garment 

(20) which can accommodate and include sleeves. The 

garment (20) is made of only one, single integrated fabric 

and has no discontinuities or seams. Additionally, the 

garment can include intelligence capability, such as the 

ability to monitor one or more body vital signs (25), or 

garment penetration (24), or both, by including a selected 

sensing component or components in the weave of the 

garment (20). 

(FIG.- 1.) 



GEORGIA TECH RESEARCH 

CORPORATION 


CENTENNIAL RESEARCH 

BUILDING, 505 TENTH STREET ATL 

ANTA, GA 30332-0415, USA. 


1. JAYARAMAN SUNDARESAN 

2. PARK SUNGMEE 








(54) Title of the invention: : A NOVEL FABRIC-BASED SENSOR FOR MONITORING VITAL 

SIGNS 

(51) International classification : A61N 


(32) Priority Date : 14/11/2000 





No 



: PCT/US01/43549 

14/11/2001 

: WO 02/40091 A2 

: 

NIL 



No 

: NIL 


(57) Abstract: The present invention comprises a fabricbased 

sensor for monitoring vital signs or other electrical 

impulses of a subject. The sensor is woven or knitted from 

conductive fibers and, when in contact with the body, receives 

signals from the wearer and transmits them to a processing or 

monitoring device through a data-output terminal. The sensor 

may be integrated into the fabric of a garment or used 

independently as a conductive patch. Additionally, the sensor 

may provide bi-directional communication by both 

monitoring electrical impulses and sending them. 

(FIG.- 1.) 



GEORGIA TECH RESEARCH 

GORPORATION 


CENTENNIAL RESEAR4CH 

BUILDING, 505 TENTH STREET ATL 

ANTA, GA 30332-0415 USA. 


1. JAYARAMAN SUNDARESAN 

2. PARK SUNGMEE 






(19) INDIA (21) 

(22) Date of filing of Application: 04/06/2003 (43) 

Application No: 575/MUMNP/2003 A 


(54) Title of the invention: DEVICE FOR WELDING NUT OR THE LIKE 

(51) International Classification : B 23 K 11/14, 11/31 (71) 


(32) Priority Date : 13/12/2000 

(33) Name of priority country : JAPAN 


No. 

: PCT/JP01/10790 

Filing Date : 10/12/2001 


No. 

: WO 02/47862 A1 (72) 



: NIL 



No. 

: NIL 



The invention relates to a nut-positioning pin provided to a lower electrode for 

projection welding of a nut. A welding device comprises an electrode holder 

(2) of double-tube structure having a cooling water passage, a guide ring (13) 

for guiding vertical movement of a coupling rod (7), an air circulation means 

(m) for preventing sputter entrance, a coupling block (28) made of a magnetic 

material for preventing the influence of an external magnetism on a 

magnetism sensor part, and a magnetic shield. The electrode holder can be 

adequately cooled, the coupling rod can be accurately guided, and entrance of 

sputter can be prevented. The adverse influence of an external magnetism on 

the sensor part can be prevented, thereby improving the sensing accuracy. 

(FIG.: 1) 



KABUSHIKI KAISHA SMK 


830-5, OOI TSUKUI-MACHI, 

TSUKUI-GUN, 

KANAGAWA 220-0202 JAPAN. 


1. MASATO HIDAKA 






(19) INDIA (21) 

(22) Date of filing of Application: 06/06/2003 (43) 




A METHOD FOR THE PRODUCTION OF A LAYERED METAL SLAB BY 

CASTING 

(51) International Classification : C 23 C 6/00 (71) 

(31) Priority Document No. : 200002796 

(32) Priority Date : 20/12/2000 

(33) Name of priority country : FINLAND 

(86) 

International Application 

No. 

: PCT/FI01/01074 



No. 

: WO 02/055753 A1 



: NIL 


(62) 


No. 

: NIL 



A method for the production of a layered metal slab by casting, 

which strip contains a central layer (2) and surface layers (3) 

oneither side of it. The central layer (2) is introduced as a 

stripthrough a mould (4), into which is introduced molten metal 

(5), the mould (4) is cooled, whereupon a layered structure (1) is 

formed as the metal solidifies. 

(FIG.: 2) 


(72) 


OUTOKUMPU OYJ 


RIIHITONTUNTIE 7, 

FIN-02200 ESPOO, FINLAND. 


1. ISOKYTO MIKA 

2. KOSKI-LAINE SAARA 

3. KOSKINEN TAISTO 

4. LIND ARI 

5. RAJAMAKI KAUKO 






(19) INDIA (21) 





METHOD AND APPARATUS FOR FEEDING SOLID MATERIAL AND 

OXIDIZING GAS INTO SUSPENSION SMELING FURNACE 

(51) International Classification : C 22 B 5/12 (71) 


(32) Priority Date : 20/12/2000 


(86) 


No. 

: PCT/FI01/01077 



No. 

: WO 02/055746 A1 



: NIL 


(62) 


No. 

: NIL 



The invention relates to an apparatus for feeding finely divided 

solids, containing at least sulphidic metal concentrate, and 

oxygenous oxidizing gas into a suspension smelting furnace, said 

apparatus comprising elements for conducting solids and 

oxidizing gas into the suspension smelting furnace. According to 

the invention, in the feed office (7) of the suspension smelting 

furnace through which solids (2) and oxidizing gas (3) are fed into 

the action chamber (1) of the suspension smelting furnace, there is 

installed a suspension creation chamber (5, 11) for a suspension 

containing solids (2) and at least part of the oxidizing gas (3) can 

be mixed to form a suspension before they flow into the reaction 

chamber (1) of the suspension smelting furnace. 

(FIG.: 1) 


(72) 


OUTOKUMPU OYJ 





1. SAARINEN RISTO 






(19) INDIA (21) 





AN ARRANGEMENT FOR CONVEYING A PLATE-LIKE PRODUCT 

FROM ONE POSITION TO ANOTHER 

(51) International Classification : B 65 G 47/90 (71) 


(32) Priority Date : 20/12/2000 


(86) 


No. 

: PCT/FI01/01078 



No. 

: WO 02/062684 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 


OUTOKUMPU OYJ 





1. LUMPPIO JUHA 




An arrangement for conveying an anode plate from one location to another, whereby said arrangement 

comprises gripping elements attached to a conveyor for gripping a plate-like piece. Elements are 

attached to the gripping element connection for the correction, at least partial, of any possible positional 

error of the anode to be transferred. 

(FIG.: NIL) 




(19) INDIA (21) 




(54) Title of the invention: METHOD FOR LEACHING COPPER CONCENTRATE 



(32) Priority Date : 20/12/2000 


(86) 


No. 

: PCT/FI01/01080 



No. 

: WO 02/50319 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 


OUTOKUMPU OYJ 





1. HAMALAINEN MATTI 




This invention relates to a method where sulfidic iron-bearing copper concentrate is leached on the 

countercurrent principle, in a chloride environment. The leaching takes place with the aid of bivalent 

copper and an oxygen-bearing gas as a multistage continuous process, under normal pressure, at a 

temperature, which as highest corresponds to the boiling point of the solution. Part of the insoluble solid 

matter is returned, counter to the main flow of solid matter, to one of the previous leaching stages or 

reactors where, as a result of the extended leaching time, the leach waste iron is recovered mostly as 

hematite. 

(FIG.: NIL) 




(19) INDIA (21) 





AN APPARATUS AND A METHOD FOR TRANSFERRING IONIC 

SPECIES BY ELECTRODIALYSIS 

(51) International Classification : B 01 D 13/02 (71) 

(31) Priority Document No. : PA 2000 01862 

(32) Priority Date : 12/12/2000 

(33) Name of priority country : DENMARK 

(86) 


No. 

: PCT/DK01/00810 

Filing Date : 06/12/2001 


No. 

: WO 02/048044 A3 



: NIL 


(62) 


No. 

: NIL 



An apparatus for transferring ionic species from a first 

liquid to a second liquid comprising: 

- at least two either cat-ion exchange membranes 

(CEM) or an-ion exchange membranes (AEM) 

defining a first chamber for the first liquid there 

between, 

- at least two further chambers for the second liquid, 

each further chamber being located adjacent to at 

least one first chamber, 

- a set of end membranes embracing said first 

chamber and said further chambers, 

- means for applying an electric field over the 

membranes. 

(FIG.: 3A) 


(72) 


JURAG SEPARATION A/S 


DTU, BUILDING 229, 

DK-2800 LYNGBY, DENMARK. 


1. ARVID GARDE 

2. JENSULRIK RYPE 

3. GUNNAR JONSSON 






(19) INDIA (21) 





AN IMPROVED METHOD FOR PREPARATION OF CEFUROXIME 

AXETIL 

(51) International Classification : C 07 D 501/04 (71) 


(32) Priority Date : N.A. 

(33) Name of priority country : NIL 


No. 

: PCT/IN01/00134 



No. 

: WO 03/010170 A1 



: NIL 


(62) 


No. 

: NIL 



An improved method for synthesis of cefuroxime axetil of 

formula (I) in high purity substantially free of the 

corresponding 2-cephem(∆ 2 )-ester of formula (II) and 

other impurities. The compound produced is valuable as a 

prodrug ester of the corresponding cephalosporin- 4carboxylic 

acid derivative i. e. cefuroxime, particularly 

suitable for oral administration in various animal species 

and in man for treatment of infections caused by grampositive 

and gram-negative bacteria. 

(FIG.: NIL) 


(72) 


LUPIN LIMITED 


159, CST ROAD, KALINA, 

SANTA CRUZ (EAST) 

MUMBAI – 400 098, 



1. KANSAL VINOD KUMAR 

2. BHAT SUNIL GURUDATT 

3. MARUTIKUMAR TANGUTURI 

VENKATA 

4. CHAVAN YUVARAJ ATMARAM 

5. SANKARAN RAMANATHAN 






(19) INDIA (21) 





AN ELECTRONIC ASSEMBLY HAVING A HEAT PIPE THAT CONDUCTS 

HEAT FROM A SEMICONDUCTOR DIE 

(51) International Classification : H 01 L 23/427 (71) 

(31) Priority Document No. : 09/730,621 

(32) Priority Date : 05/12/2000 



No. 

: PCT/US01/49897 



No. 

: WO 02/058138 A3 



: NIL 


(62) 


No. 

: NIL 



An electronic assembly (10) is described 

including a motherboard(12), a semiconductor 

die(20) mounted to the motherboard(12), and a 

heat pipe(22) having an evaporator portion(34) 

adjacent the die, n(20), and a condenser portion 

(36) distant from the die(20). The heat pipe(22) is 

connected to a ground plane(60) of the 

motherboard(12) at various locations. Structural 

integrity of the heat pipe(22) is provided by an 

insert(142) in an evaporator portion(34) of the 

heat pipe(22) and because of opposing recessed 

seat portions(74, 76, 80, 82) that contact one 

another. Another feature of the electronic 

assembly(10) is that it has a sheet(90) of material 

forming a plurality of fins(30) that are welded to 

a condenser portion(36) of the heat pipe(229). 

(FIG.: 1) 

Total Pages: 24. 

(72) 




2200 MISSION COLLEGE 

BOULEVARD, SANTA CLARA, 

CALIFORNIA 95052, 

UNITED STATES OF AMERICA. 


1. AJIT V. SATHE 

2. MICHAEL JIM WITHERSPOON 

3. KRISTOPHER J. FRUTSCHY 

4. RAVI S. PRASHER 






(19) INDIA (21) 





(32) Priority Date : 15/12/2000 


KINGDOM 

(86) 


No. 

: PCT/EP01/13314 



No. 

: WO 02/48301 A1 



: NIL 


(62) 



No. 

: NIL 




LIGAND AND COMPLEX FOR CATALYTICALLY BLEACHING A 

SUBSTRATE 

(72) 




HINDUSTAN LEVER HOUSE 


MUMBAI- 400 020, 



1. HEIDI BOERZEL 

2. PETER COMBA 

3. RONALD HAGE 

4. MARION KERSCHER 

5. JOACHIM LIENKE 

6. MICHAEL MERZ 




The present invention relates to a bleaching composition comprising: a) a monomer ligand or transition metal catalyst 

thereof of a ligand having the formula (I); wherein each R is independently hydrogen, F, Cl, Br, hydroxyl, C1-C4-alkylO- 

, -NH-CO-H, -NH-CO-C1-C4-alkyl, -NH2, -NH-C1-C4-alkyl, and C1-C4-alkyl; R1 and R2 are independently selected 

from: C1-C4-alkyl, C6-C10-aryl, and, a group containing a heteroatom capable of coordinating to a transition metal, 

wherein at least one of R1 and R2 is the group containing the heteroatom; R3 and R4 are independently selected from 

hydrogen, C1-C8 alkyl, C1-C8-alkyl-O-C1-C8-alkyl, C1-C8-alkyl-O-C6-C10-aryl, C6-C10-aryl, C1-C8-hydroxyalkyl, 

and -(CH2)nC(O)OR5 wherein R5 is independently selected from: hydrogen, C1-C4-alkyl, n is from 0 to 4, and mixtures 

thereof; and , X is selected from C=O, -[C(R6)2]y- wherein Y is from 0 to 3, each R6 is independently selected from 

hydrogen, hydroxyl, C1-C4-alkoxy, C1-C4-alkyl; and b) the balance carriers and adjunct ingredient. 

(FIG.: NIL) 




(19) INDIA (21) 


(54) Title of the invention: LAUNDRY COMPOSITION 



(32) Priority Date : 15/12/2000 

(33) Name of priority country : EUROPE 


No. 

: PCT/EP01/14490 



No. 

: WO 02/48302 A1 (72) 



: NIL 


(62) 



No. 

: NIL 









MUMBAI- 400 020, 



1. FINDLAY PAUL HUGH 

2. KUKULJ DAX 

3. MEALING DAVID RICHARD 

ARTHUR 




A laundry treatment composition comprising composition comprising: i) a polymer having an average repeat unit 

of: in which R1-6 are independently of one another selected from H, a hydrolysable group, or a fibre reactive 

group in which when R1-6 is a hydrolysable group the degree of substitution is 0 to 1, and wherein R1-6 is a fibre 

reactive group the degree of substitution is from 0.05 to 1 and; ii) a carrier agent selected from surfactants, 

softening compounds or water wit the proviso that when the carrier agent is water the composition further 

comprises perfume. 

(FIG.: NIL) 




(19) INDIA (21) 


(54) Title of the invention: OXYGEN LANCE IGNITER 

(51) International Classification : E 21 B 7/14, 

B 23 K 7/00 


(32) Priority Date : 21/12/2000 



No. 

: PCT/SE01/02793 



No. 

: WO 02/50396 A1 



: NIL 


(62) 


No. 

: NIL 



In accordance with the method and the device according to the 

invention, previous pure pyrotechnic primers for initiating the 

ignition charges (6a, 6b) of the oxygen lance igniters (13) are 

replaced by a small quantity of powdered zirconium (7). 

Zirconium is pyrophoric and therefore ignites, providing it has a 

sufficiently large surface area, in the presence of a sufficient 

quantity of pure oxygen, although in ordinary air it is no more 

flammable than ordinary wood. 

(FIG.: 1) 




(71) 

(72) 


FERROX AB 


S-712 82 GRYTHYTTAN, SWEDEN. 


1. BOERJE ERICKSSON 

2. LENNART ERIKSSON 






(19) INDIA (21) 





THE HYDRAULIC DIFFERENTIAL CYLINDER FOR A DEVICE WITH AT 

LEAST ONE EXTENSION ARM OR SUPPORT ARM FOR MULTI-LINKED 

CRANE-SHAPED EXTENSION ARMS, CONCRETE SPREADER 

COLUMNS AND SIMILAR 

(51) International Classification : E 04 G 21/04 (71) 

(31) Priority Document No. : 100 64 365.5 

(32) Priority Date : 22/12/2000 

(33) Name of priority country : GERMANY 

(86) 


No. 

: PCT/EPO1/15222 



No. 

: WO 02/052115 A2 



: NIL 


(62) 



No. 

: NIL 


(72) 


SCHWING GMBH 


HEERSTRASSE 11, 44647 HERNE, 

GERMANY. 


1. SIEGFRIED TRUMPER 

2. HORST HECKMANN 




The invention relates to a device with at least one extension arm or support arm for multi-linked crane shaped 

extension arms, concrete spreader columns and similar, comprising at least one hydraulic differential cylinder for 

actuating a support arm. The cylinder comprises a hollow piston rod which has a tubular segment and two end 

pieces arranged on the ends of said segment, whereby at least one of the end pieces is welded on to the segment 

thereof. The welded joint is machined and the root of the weld is eliminated. At least one of the end pieces 

comprises a through opening which enables tool access in order to machine the hollow cavity of the hollow piston 

rod. 

(FIG.: NIL) 




(19) INDIA (21) 




(54) Title of the invention: ENHANCEMENT OF AIR BLEACHING CATALYSTS 

(51) International Classification : C 11 D 3/39, 3/28 (71) 


(32) Priority Date : 18/12/2000 

(33) Name of priority country : GREAT BRITAIN 


No. 

: PCT/EP01/13196 



No. 

: WO 02/50229 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI- 400 020. 



1. ADRIANUS CORNELIS MARIA 

APPEL 

2. RONALD HAGE 

3. PHILIPPUS CORNELIS VAN 

DER HOEVEN 

4. JOACHIM LIENKE 

5. RICHARD GEORGE SMITH 




The invention relates to catalytically bleaching substrates, especially laundry fabrics, with atmospheric oxygen or 

air in the presence to an air bleaching facilitator. 

(FIG.: NIL) 




(19) INDIA (21) 


Application No: 606/MUMNP/2003 A 


(54) Title of the invention: METHOD AND DEVICE FOR CAPACITIVE MEASURING LEVELS 

(51) International Classification : G 01 F 23/26 (71) 

(31) Priority Document No. : 1) 100 63 557.1 

2) 101 09 153.4 

(32) Priority Date : 1) 20/12/2000 

2) 24/02/2001 


(86) 


No. 

: PCT/EP01/14980 



No. 

: WO 02/50498 A1 



: NIL 


(62) 



No. 

: NIL 


The invention relates to a method and a device for measuring 

and indicating the level of a filler material in a container, said 

filler material being either electroconductive or nonconductive. 

A sensor (22) is applied to the wall of the container (20) or is 

integrated into the same. An alternating voltage is applied to the 

sensor (22) in order to measure the level, the capacity or the 

electrical field produced being a measure for the fill level. 

(FIG.: 2) 


(72) 


ABERTAX RESEARCH & 

DEVELOPMENT LTD. 


7, LOREDANA COURT, 

8 G. KALI STREET, TA’XBIEX, 

MSD 14, MALTA. 


1. DR. MARTIN FLORIN 

2. WERNER SCHMIDT 






(19) INDIA (21) 




(54) Title of the invention: METHOD FOR CARBAMOYLATING ALCOHOLS 

(51) International Classification : C 07 D 401/06 (71) 


(32) Priority Date : 31/01/2001 

(33) Name of priority country : U.S.A. 


No. 

: PCT/IB02/00082 



No. 




: NIL 


(62) 



No. 

: NIL 


(72) 


WARNER-LAMBERT COMPANY LLC 


201 TABOR ROAD, MORRIS PLAINS, 

NEW JERSEY 07950, 



1. JAMES EDWARD ELLIS 




The present invention includes a method for carbamoylating an alcohol with sodium cyanate in the presence of 

methanesulfonic acid. The reaction can be conducted under anhydrous conditions. This method is suitable for 

carbamoylating a molecule including both an alcohol moiety and a basic moiety and/or a molecule including both 

an alcohol moiety and a sulfenyl moiety, such as the sulfenyl alcohol precursor of the antiviral agent Capravirine. 

(FIG.: NIL) 




(19) INDIA (21) 





NOVEL PROCESS FOR THE SYNTHESIS OF 5-[4-FLUOROPHENYL]-1-[2- 

((2R, 4R)-4-HYDROXY-6-OXO-TETRAHYDRO-PYRAN-2-YL]-ETHYL]-2- 

ISOPROPYL-4-PHENYL-1H-PYRROLE-3-CARBOXYLIC ACID 

PHENYLAMIDE 

(51) International Classification : C 07 D 405/06 (71) 


(32) Priority Date : 09/01/2001 



No. 

: PCT/IB01/02729 



No. 

: WO 02/055519 A2 



: NIL 


(62) 



No. 

: NIL 


(72) 


WARNER-LAMBERT COMPANY LLC 


201 TABOR ROAD, MORRIS PLAINS, 




1. DONALD EUGENE BUTLER 

2. RANDALL LEE DEJONG 

3. JADE DOUGLAS NELSON 

4. MICHAEL GERARD PAMMENT 

5. TIMOTHY LEE STUK 




An improved process for the preparation of 5-(4-fluorophenyl)-1-[2-((2R,4R)-4-hydroxy-6-oxotetrahydro-pyran-2-yl)-ethyl]-2-isopropyl-4-phenyl-1H-pyrrole-3-carboxylic 

acid phenylamide by a 

novel synthesis is described where methyl cyanoacetate is converted in eight operations or fewer to the 

desired product, as well as other valuable intermediates used in the process. 

(FIG.: NIL) 




(19) INDIA (21) 





PROCESS FOR THE PREPARATION OF HYDROLYZED SUNFLOWER 

LECITHIN 

(51) International Classification : A 23 D 7/00, 9/00 (71) 


(32) Priority Date : 21/12/2000 



No. 

: PCT/EP01/14264 



No. 

: WO 02/49444 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI- 400 020. 



1. COR’T HOOFT 

2. MARCELLE VAN DEN 

KOMMER 

3. JACOBUS CORNELIS SEGERS 




The invention concerns a food composition, suitable for shallow frying, comprising triglycerides, wherein least 

60 wt.% of triglycerides is of vegetable origin, and 0.05-3 wt.% sunflower lecithin. The invention further 

concerns a process for the preparation of hydrolyzed sunflower lecithin. 

(FIG.: NIL) 




(19) INDIA (21) 


(54) Title of the invention: ANTIPERSPIRANT PRODUCTS 

(51) International Classification : A 61 K 7/32 (71) 


(32) Priority Date : 21/12/2000 

(33) Name of priority country : UNITED KINGDOM 

(86) 


No. 

: PCT/EP01/13253 



No. 

: WO 02/49590 A2 



: NIL 


(62) 



No. 

: NIL 




(72) 






MUMBAI- 400 020, 



1. RIELEY HUGH 

2. SMITH IAN KARL 




Antiperspirant products and methods for achieving antiperspirancy utilizing compositions comprising an 

antiperspirant salt and a water soluble polymer, characterized in that: I) the polymer comprises Brrnsted acid 

groups and acts as a co-gellant for the antiperspirant salt when mixed therewith in the presence of water; and ii) 

the polymer is physically separate from antiperspirant salt prior to application. 

(FIG.: NIL) 




(19) INDIA (21) 



(51) International Classification : C 11 D 17/00, 3/382, 

3/12, 3/22 


(32) Priority Date : 21/12/2000 



No. 

: PCT/EP01/13458 



No. 

: WO 02/50234 A1 



: NIL 


(62) 



No. 

: NIL 


Application No: 624/MUMNP/2003 A 


A TABLET OF COMPACTED PARTICULATE CLEANING 

COMPOSITION 

(71) 

(72) 






MUMBAI- 400 020. 



1. JELLES VINCENT BOSKAMP 

2. IAN CHARLES CALLAGHAN 




The invention provides a tablet of compacted particulate cleaning composition comprising at least one cleaning 

ingredient which is an organic surfactant, detergency builder or a bleach, wherein the tablet or a discrete region 

thereof comprises water-swellable disintegration-promoting particles, said particles comprising; a) disintegration 

material which is (i) cellulosic material from a plant source other than timber or (ii) plant material which 

comprises both cellulose and lignin, obtainable by fragmentation of plant material without separation of its fibers 

into a liquid dispersion, and b) carrier material which has a solubility in deionised water at 20oC of 1 gram per 

litre or less. The tablets have an aesthetically acceptable colour even though they comprise coloured disintegrant 

material and they exhibit good disintegration and strength properties. The disintegration-promoting particles are 

also provided. 

(FIG.: NIL) 




(19) INDIA (21) 


(54) Title of the invention: A FABRIC CARE COMPOSITION 



(32) Priority Date : 22/12/2000 

(33) Name of priority country : EP 


No. 

: PCT/EP01/14770 



No. 

: WO 02/051972 A1 



: NIL 


(62) 



No. 

: NIL 




(72) 






MUMBAI- 400 020, 



1. MOORFIELD DAVID 

2. WHILTON NICOLA 




A fabric care composition comprises (i) an organophilic clay; (ii) a functionalised oil; and (iii) water. The 

composition may be used to provide fabrics with softness and/or anti-wrinkle and/or other fabric benefits in 

laundering processes. 

(FIG.: NIL) 




(19) INDIA (21) 


(54) Title of the invention: UNIDIRECTIONAL COUNTER 

(51) International Classification : G 06 M 3/12, 1/06 (71) 


(32) Priority Date : 15/12/2000 



No. 

: PCT/IB01/02248 



No. 

: WO 02/48957 A1 (72) 



: NIL 


(62) 



No. 

: NIL 





LANDIS+GYR AG [FORMERLY 

SIEMENS METERING AG] 


FELDSTRASSE 1, 

CH-6300 ZUG, SWITZERLAND. 


1. ERNST BURGI 




The invention relates to a unidirectional counter comprising a driven worm gear (1) and a least one numerical display (3), 

driven by the rotation of the worm gear (1). The worm gear (1) is connected to a first system gear (8) by means of a first 

ratchet-pawl system (6, 7a, b). Said first ratchet-pawl system (6, 7a, b) comprises at least a first pair of pawls (7a, b) with 

two connected pawls (7a, b) working in tandem. Furthermore a reverse gear (10) may be driven by the worm gear (1), 

which is connected to a second system gear (14) by means of a second ratchet-pawl system (12, 13a, b). Said second 

ratchet-pawl system (12, 13a, b) comprises a second pair of pawls (13a, b) with two connected pawls (13a, b) working in 

tandem. According to the invention, an exact as possible totalisation and display of used energy units even on a change in 

direction may be achieved, whereby at least one pawl (7a, b, 13a, b) on each of the first and second ratchet-pawl systems 

(6, 7a, b; 12, 13a, b) are in the engaged position, pointing towards a ratchet tooth (6,12), or are in direct contact with a 

ratchet tooth (6, 12). 

(FIG.: 1) 




(19) INDIA (21) 





METHOD AND APPARATUS FOR FEEDING A STACK OF METALLIC 

SHEETS INTO A MELTING FURNACE 

(51) International Classification : F 27 D 3/00 (71) 


(32) Priority Date : 04/01/2001 


(86) 


No. 

: PCT/FI02/00001 



No. 

: WO 02/057698 A1 



: NIL 


(62) 



No. 

: NIL 


A method for conveying stacks of metallic sheets, in 

particular stacks of metallic cathodes, into a melting 

furnace. The stack of metallic sheets (1) is gripped by a 

grapple element (10), such asa lifting grapple, which is 

arranged on a transfer device, and the stack of metallic 

sheets (1) is transferred into the melting furnace (2) 

chamber (14), and that at a predetermined height insidethe 

furnace chamber, preferably relatively near the bottom of 

thefurnace and/or melt, the metallic stack (1) is released. 

(FIG.: 1) 


(72) 


OUTOKUMPU OYJ 



FIN-02200 ESPOO, FINLAND 


1. RAITANEN TERO 

2. SAAMANEN JUKKA 

3. MARTTILA TOM 






(19) INDIA (21) Application No: 634/MUMNP/2003 A 

(22) Date of filing of Application: 23/06/2003 (43) Publication Date: 24/06/2005 


A COMPUTERISED ADMINISTRATION SYSTEM AND METHOD FOR 

ADMINISTERING THE CONDUCT OF EXAMINATIONS SUCH AS 

ACADEMIC EXAMINATIONS 

(51) International Classification : G 09 B 7/07 (71) 


(32) Priority Date : 27/11/2000 



No. 

: PCT/IB01/02760 



No. 

: WO 02/42963 A2 (72) 



: NIL 



No. 

: NIL 



The present invention provides a computerised administration 

system for administering the conduct of examinations such as 

academic examinations. The system comprises central computer 

processing means (10) for processing and storing data, a plurality 

of local computer processing means (32) physically remote from 

the central computer processing means (10) for use by examination 

candidates, and a communications network (20) connecting the 

central computer processing means (10) to each of the local 

computer processing means (32) to facilitate data transfer there 

between. Each local computer processing means (32) has sampling 

means (34) for taking identification samples from an examination 

candidate. During the examination, each examination candidate is 

presented with examination questions which he/she answers by 

inputting the answers into one of the plurality of local computer 

processing means (32) and the sampling means (34) of each local 

computer processing means (32) takes identification samples from 

each candidate at random intervals. The local computer processing 

means (32) sends the identification samples from each candidate to 

the central computer processing means (10) via the 

communications network (20) together with the examination 

answers of the said candidate. The present invention also relates to 

a method of administering the conduct of examinations such as 

academic examinations and to a program and an information 

storage medium for storing the program. 


ARENBEE MEDIA CONSULTANTS 

PRIVATE LIMITED 


80-A, COLLECTORS COLONY, 

CHEMBUR, MUMBAI – 400 074. 



1. BHASKAR RAMAKRISHNAN 

NAIR 




(FIG.: 1) Total Pages: 40. 



(19) INDIA (21) 





METHOD AND SYSTEM FOR EFFICIENT DISSEMINATION OF 

INFORMATION 

(51) International Classification : H 04 H 9/00, 1/00 (71) 

(31) Priority Document No. : 1) 1017087 

2) 1017301 

(32) Priority Date : 1) 12/01/2001 

2) 07/02/2001 

(33) Name of priority country : THE 

NETHERLANDS 

(86) 


No. 

: PCT/EP02/00276 



No. 

: WO 02/056512 A1 



: NIL 


(62) 


No. 

: NIL 



Method and system for the dissemination of information via 

a broadcasting system (1, 2, 3, 4) or via other means (14, 

15, 17). An information server (12) is accessible to 

telecommunication terminals (7) via a telecommunication 

network (5). A user who hears, sees or reads an interesting 

primary information block selects it by making a call via his 

telecommunication terminal (7) to the information server 

(12). On the basis of the selection code, the information 

server selects a secondary information block and sends it t 

he user. The address of the user can be derived from the 

CLI of the telecommunication terminal (7). In addition, the 

secondary information can be returned directly to the 

terminal (7) corresponding with that CLI. 

(FIG.: 1) 


(72) 


KONINKLIJKE KPN N.V. 


STATIONSPELIN 7, 

NL-9726 AE GRONINGEN, 

THE NETHERLANDS 


1. VAN STEENBERGEN ATE 

SANDER 

2. VAN BIJSTERVELD CORNELIS 

CASPARUS 

3. SNIP JAN GERARD 






(19) INDIA (21) 





SKIN CARE PRODUCT CONTAINING RETINOIDS AND 

PHYTOESTROGENS IN A DUAL COMPARTMENT PACKAGE 



(32) Priority Date : 28/12/2000 



No. 

: PCT/EP01/14483 



No. 

: WO 02/053122 A2 



: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI- 400 020. 



1. PILLAI SREEKUMAR 

2. GRANGER STEWART PATON 

3. SCOTT IAN RICHARD 

4. POCALYKO DAVID JOSEPH 




A stable skin care product containing a first composition comprising from about 0.001% to about 10% of a 

retinoid; a second composition comprising from about 0.001% to about 10% of a phytoestrogen; a first 

compartment for storing the first composition; and a second compartment for storing the second composition, the 

first and second compartments being joined together. 

(FIG.: NIL) 




(19) INDIA (21) 





STABLE SKIN CARE PRODUCT CONTAINING A RETINOID AND A 

RETINOID BOOSTER SYSTEM IN A DUAL COMPARTMENT PACKAGE 



(32) Priority Date : 28/12/2000 



No. 

: PCT/EP01/14485 



No. 

: WO 02/053123 A2 



: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI- 400 020. 




2. CHANDAR PREM 





A stable skin care product comprising a first composition comprising about 0.001% to about 10% of a retinoid; a 

second composition comprising about 0.0001% to about 50% of at least one retinoid booster; a first compartment 

for storing the first composition, wherein the first compartment keeps the first composition out of contact with 

oxygen; and a second compartment for storing the second composition, the first and second compartments being 

joined together. 

(FIG.: NIL) 




(19) INDIA (21) 





A STABLE SKIN CARE COMPOSITION IN A DUAL COMPARTMENT 

PACKAGE 



(32) Priority Date : 28/12/2000 



No. 

: PCT/EP01/14486 



No. 

: WO 02/053108 A3 



: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI- 400 020, 



1. PILLAI SREEKUMAR 



4. POCALYKO DAVID JOSEPH 




A stable skin care product containing a first composition comprising about 0.001 % to about 10 % of a retinoid; a 

second composition comprising about 0.0001 % to about 50 % of at least one retinoid booster and about 0.001 % 

to about 10 % of a phytoestrogen; a first compartment for storing the first composition; and a second 

compartment for storing the second composition, the first and second compartments being joined together. 

(FIG.: NIL) 




(19) INDIA (21) 





IN VITRO METHOD FOR TRANSFECTION OF EUKARYOTIC CELL FOR 

PRODUCING DRUG FOR NON-VIRAL GENE THERAPY 

(51) International Classification : C 12 N 15/87 (71) 


(32) Priority Date : 10/01/2001 


(86) 


No. 

: PCT/DE02/00060 



No. 

: WO 02/055721 A2 



: NIL 



No. 

: NIL 



The invention relates to a method for the transfection of cells using 

at least one protein capable of forming nucleoprotein filaments. Said 

protein is first modified by at least one functional constituent which 

influences at least one step of the transfection, and the nucleic acid 

to be transfected is then loaded with the modified protein. The 

nucleic acid and the protein form a filamentary complex, and said 

complex is then added to the cells to be transfected. The invention 

also relates to a transfection agent of nucleoprotein filaments (NPF), 

at least one protein forming a nucleoprotein filament being modified 

by at least one functional constituent for the transfection. The 

invention further relates to the use of the inventive transfection agent 

for producing a medicament for the gene therapeutic treatment of 

humans and animals. Finally, the invention relates to corresponding 

pharmaceutical preparations, especially for use in gene therapy, and 

the use of such transfection agents in the form of constituents in kits. 

(72) 


AMAXA GMBH 


NATTERMANNALLEE 1, 

50829 KOLN, GERMANY. 


1. SCHMIDT HANNS-MARTIN 

2. ALTROGGE LUDGER 

3. LENZ DIETMAR 

4. RIEMEN GUDULA 

5. BROSTERHUS HELMUT 

6. LORBACH ELKE 

7. HELFRICH JULIANA 

8. HEIN KATHARINA 

9. GREMSE MARION 

10. MALES TATJANA 

11. CHRISTINE RAINER 

12. SIEBENKOTTEN GREGOR 

13. ORTMANN BODO 

14. TURBANSKI TAMARA 

15. KLAES ANDREA 




(FIG.: 20) 




(19) INDIA (21) 





A SYSTEM FOR SUPPORTING THE MANAGEMENT OF AN 

INTEGRATED COMMUNICATIONS PROVIDER (ICP) 

(51) International Classification : G 06 F 5/01 (71) 


(32) Priority Date : 27/12/2000 



No. 

: PCT/US01/50224 



No. 

: WO 02/052380 A2 



: NIL 


(62) 



No. 

: NIL 


(72) 


WISOR TELECOM CORPORATION 

AND 

SELWOOD CHRISTOPHER J. 


1. SUITE 200, 300 PROFESSIONAL 

DRIVE, GAITHERSBURG, MD 

20879, U.S.A. 

2. 4515 SANGAMORE ROAD, 

BETHESADA MD 20816, U.S.A. 


1. SELWOOD CHRISTOPHER J. 




A system for management of an integrated communications provider comprising a means of automatically 

retrieving customer service records and preparing sales proposals therefrom. The invention further comprises 

components for pre-ordering management functions, circuit management, design management, service 

management, and gateway to incumbent local exchange carriers and trading partners. The system incorporates 

features that automate comparisons between existing services and proposal services, alarming of failures of 

confirmations, optimizing on-net and off-net services, creation of cutover reports and issuance of service requests 

to local exchange carriers and trading partners. 

(FIG.: NIL) 




(19) INDIA (21) 





AN APPARATUS FOR USE IN SAMPLING MATERIAL ON-LINE IN A 

PROCESS SYSTEM 

(51) International Classification : G 01 N 1/20 (71) 


(32) Priority Date : 31/01/2001 


(86) 


No. 

: PCT/SE02/00153 



No. 




: NIL 


(62) 



No. 

: NIL 


An apparatus for use in sampling material on-line 

in a process system, comprising a sample collector 

(1) for receiving a sample of material, an elongate 

shaft (10) defining a passageway (14) carrying a 

measurement probe (11) for taking measurements 

from a collected sample, a pressurised fluid supply 

(31) connected to the passageway for delivering a 

pressurised fluid through the passageway to the 

sample collector for displacing the collected 

sample and a nozzle (33) provided at the distal end 

of the measurement probe (11) for distributing the 

pressurised fluid to the sample collector for 

displacing the collected sample from the sample 

collector (1). 

(FIG.: 3) 


(72) 


ASTRAZENECA AB 


S-151 85 SODERTALJE, SWEDEN. 


1. LENNART BJORK 

2. STAFFAN FOLESTAD 

3. MATS JOHANSSON 

4. ANDERS KLEVENSPARR 

5. INGELA NIKLASSON BJORN 






(19) 

INDIA (21) Application No: 675/MUMNP/2003 A 

(22) Date of filing of Application : 03/07/2003 


(51) International Classification: G 10 D 13/00 (71) 

(31) Priority Document No. : 00/16528 



(86) 


A DEVICE FOR PRODUCING A SERIES OF CLOSELY SPACED 

PERCUSSIVE BLOWS BY A SINGLE OPERATOR. 

18/12/2000 

FRANCE 

International Application : PCT/FR01/04020 

No. and Filing Date : 17/12/2001 


Publication No. WO 02/50811 A1 

(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : The invention concerns a method for 

producing a series of percussions in close succession on at least 

a percussion instrument such as a bass drum by a single 

operator. The operator activates successively and repetitively 

with the leg, then with the foot corresponding to two mobile 

parts comprising each a beater, adapted to strike the percussion 

instrument to produce cycle of at least four successive impacts 

separated in pairs by a time interval less than a quarter of a 

second. 

Total Pages :26. 


S 3 S 


QUARTIER LE COLOMBIER, 

F-26240 MUREILS, 

FRANCE. 




(19) 




(51) International Classification: A 61 M 15/00 (71) 

(31) Priority Document No. : 22/MUM/2001 



(86) 


AN IMPROVED DEVICE FOR ADMINISTERING ORALLY OR 

NASALLY METERED MEDICINAL COMPOSITION BY 

INHALATION. 

08/01/2001 

INDIA 

International Application : PCT/IN02/00004 



Publication No. WO 02/053216 

A3 

(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


CIPLA LIMITED 


289, BELLASIS ROAD, 

MUMBAI CENTRAL, 

MUMBAI – 400 008, 


(57) Abstract : An improved device for metered administration of medicament by inhalation orally comprises of a 

container for receiving a circular cartridge of medicament. The cartridge has a plurality of cavities along its circumference 

to hold a predetermined quantity of medicament. Each cavity is sealed by a pierceable sealing means. A piercing member 

pierces the said sealing means and thereby penetrates into the cavity. The piercing member has a hollow cylindrical part 

in fluid communication with an inhalation nozzle. The container has a view window at a location below the nozzle to 

enable the user to ascertain the evacuation of medicament from the cavity pierced for use. 





(19) 




(51) International Classification: A 61 K 7/38 (71) 




(86) 


ANTIPERSPIRANT OR DEODORANT COMPOSITIONS 

COMPRISING ACTIVATED ALUMINIUM CHLORHYDRATE. 

09/01/2001 

UNITED 

KINGDOM 

International Application : PCT/EP01/15389 



Publication No. WO02/055044 A1 

(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 






MUMBAI – 400 020, 



1. CHUAH BENG SIM 

2. FRANKLIN KEVIN RONALD 

3. HOUGH GORDON CHARLES 


(57) Abstract : Translucent anhydrous formulations containing particulate commercially available activated aluminium 

chlorohydrate (AACH) have a perceptible yellowness. The yellowness of translucent anhydrous compositions containing 

AACH can be ameliorated or eliminated whilst retaining the improved antiperspirant efficacy of AACH by controlling its 

water content to the range of 9 to 18%. The appearance of yellow formulations in or on a dispensing package, prior to 

application to the body, can appear to be neutralised to the human eye by employing a dispenser having a complementary 

colour in wall contacting the formulation, to promote achromicity. The complementary colour of the wall is dark green 

for yellow formulations. 







(54) Title of the invention: IMPROVED COKE DRUM DE-HEADING SYSTEM. 

(51) International Classification: C 10 B 25/00 (71) 

(31) Priority Document No. : 1. 60/275,527 

2. 09/946,917 

3. 60/335,534 

4. 10/096,301 


1. 12/03/2001 

2. 09/09/2001 

3. 19/10/2001 

4. 11/03/2002 

(33) Name of priority country : US 

(86) International Application : PCT/US02/07371 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


CURTISS-WRIGHT FLOW CONTROL 

CORPORATION 


4 BECKER FARM ROAD, ROSELAND, 

NEW JERSEY 07068-1739, 

U.S.A. 


LAH RUBEN F. 




(57) Abstract : The present invention features a coke drum de-heading 

system (10) without having to physically remove the head units. This is 

accomplished using a specially designed dual seated, linear motion goggle 

blind gate valve, or de-header valve (12), that is removably coupled to and 

seals against the flanged (42) portion of a coke drum (18) much the same 

way a conventional head unit would be attached. The de-header valve (12) 

is equipped with, among other things, a sliding blind (122) that is 

contained and capable of moving within an upper (34) and a lower (38) 

seat, wherein one of such seats is a floating dynamic, live loaded seat that 

is capable of automatic adjustment through one or more loading zones so 

as to seal the blind (122) between the upper (34) and lower (38) seats. The 

movement of 

the sliding blind (122) serves to open and close the de-header valve 


(12), wherein in a closed position, the de-header valve (12) is prepared to receive the resid byproduct feed from the 

refinery process used to manufacture coke (4). Once the drum (18) is full, the de-header valve (12) may be actuated 

(opened), wherein the coke (4) that has accumulated on the blind (106) is sheared by the upper (34) and lower (38) seats, 

thus de-heading the coke drum (18) and facilitating the removal of coke (4) using methods commonly known in the art. 




(19) 




(51) International Classification: H 05 K 7/10 (71) 




(86) 


AN INTEGRATED CIRCUIT PACKAGE AND SOCKET, AND AN 

INTEGRATED CIRCUIT POWER DELIVERY SYSTEM. 

30/12/2000 

USA 

International Application : PCT/US01/44828 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A socket and package apparatus are disclosed 

for increasing the amount of power that can be delivered from 

an IC board to an IC where the IC package is mounted in a 

socket connected to the IC board. The apparatus has two 

separable and distinct parts designed to electrically engage. 

The package is designed with a power bar where the panels of 

the power bar are permanently and electrically connected to 

various power planes of the IC package along its entire 

adjacent wall. The socket is designed with a power bar carrier 

designed to maximize the current flow from the IC board to 

the power bar. The package is then engaged into the socket. 


(72) 




2200 MISSION COLLEGE BOULEVARD, 

SANTA CLARA, 




1. XIE HONG 

2. STONE BRENT S. 






(19) 



(54) Title of the invention: ORAL COMPOSITION. 





(86) 

16/01/2001 

EUROPE 





(61) 

(62) 



Filed on N.A. 

Divisional to 




(72) 






MUMBAI – 400 020, 



1. BHAKOO MANMOHAN 

2. JOINER ANDREW 

3. STEELE KATHERINE ANNE 

4. TAYLOR DAVID 

5. THOMPSON KATHERINE MARY 

6. THORNTHWAITE DAVID WILLIAM 




(57) Abstract : An oral composition comprising picolinic acid and a peroxyl species or equivalent source thereof, 

characterised in that the molar ratio of picolinic acid to peroxyl species or equivalent source thereof is from 1:30 to 100:1. 





(19) 




(54) Title of the invention: CLEANSING WIPE ARTICLE AND METHOD OF MANUFACTURE. 




17/01/2001 


(86) 



(87) International : WO 02/056741 A1 




Filed on N.A. 

(62) 

Divisional to 



(57) Abstract : A disposable substantially dry foamable product 

is described including a water-insoluble substrate such as a 

flexible web, the substrate having first and second major 

surfaces, with a plurality of moguls spaced apart on the first 

major surface and a foamable composition deposited in major 

amounts on the second surface and a minor amount on the first 

surface. A method for producing the product is also described 

which employs the moguls in juxtaposition to a guide roller to 

establish space between a surface of the roller and the first 

surface of the substrate. Foamed composition is deposited onto 

the second surface which by seepage through apertures in the 

substrate allow a minor portion of the coating composition to 

deposit on the first surface of the substrate. 


(72) 






MUMBAI – 400 020, 



1. SLAVTCHEFF CRAIG STEPHEN 

2. GOTT ROBERT EDWARD 

3. ZNAIDEN ALEXANDER PAUL 

4. MACEDO FILOMENA AUGUSTA 







(19) 




(54) Title of the invention: DIGITAL MULTIMEDIA CONTACT CENTER. 

(51) International Classification: H 04 M 3/523 (71) 



30/01/2001 


(86) 


No. and Filing Date : 24/01/2002 

(87) International : WO 02/065741 A2 




Filed on N.A. 

(62) 

Divisional to 



(72) 


NUASIS CORPORATION 


260 GISH ROAD, SAN JOSE, 




1. BROUGHTON JUSTIN 

2. MCPARTLAN KEVIN J. 

3. RODGERS ELIZABETH 

4. RODGERS ROBERT S. 

5. COVDY IVAN 

6. HO ROY 

7. KOWALSKI CARL RAYMOND 

8. MCCALMONT D. THOMPSON 

9. STINE ART 

(57) Abstract : A tiered service model for a digital multimedia contact center assigns an entering contact to an initial 

service tier based on routing criteria for the contact and may escalate or de-escalate the contact to a different service tier if 

the routing criteria changes. The routing criteria is initially determined based on a media type associated with the contact. 

The digital multimedia contact center contains a set of media routers, each of which passes a contact of a particular media 

type to a workflow engine which executes workflows to direct the processing of contacts at service tiers that require agent 

activity. Agents are allocated to contacts by a dynamic automate contact distributor and the appropriate media router is 

used to route the contact to an agent. The work flow engine also executes workflows for agents to control the allocation 

of agents to contacts. 





(19) 





(31) Priority Document No. : 60/275,061 



PURIFICATION OF 

2-NITRO-4-METHYLSULPHONYLBENZOIC ACID. 

26/03/2001 


(86) 

International Application : PCT/GB02/01433 


(87) International : WO 02/076934 A2 




Filed on N.A. 

(62) 

Divisional to 



(72) 


SYNGENTA LIMITED 


EUROPEAN REGIONAL CENTRE, 

PRIESTLEY ROAD, 

SURREY RESEARCH PARK, 

GUILDFORD, SURREY GU2 7YH, 

ENGLAND. 


1. JAVDANI KAMBIZ 

2. RODRIGUEZ GILBERT 

3. MUXWORTHY JAMES PETER 

(57) Abstract : A method for removing impurities from 2-nitro-4-methylsulfonylbenzoic acid which comprises at least 

two of the following steps, in any order, (a) dissolving 2-nitro-4-methylsulfonylbenzoic acid in water at a pH of about 2 

to 10, followed by filtration; (b) contacting an aqueous solution of 2-nitro-4-methylsulfonylbenzoic acid with activated 

carbon at a pH of about 2 to 10; (c) treating an aqueous solution of 2-nitro-4-methylsulfonylbenzoic acid with sufficient 

base to hydrolyze undesired nitro and dinitro substituted impurities; followed by maintaining the resulting aqueous 

solution comprising 2-nitro-4-methylsulfonylbenzoic acid at a temperature of up to about 95C, and adjusting the pH of 

said solution to about a pH which is sufficient to effect crystallization of 2-nitro-4-methylsulfonylbenzoic acid upon 

cooling. 





(19) INDIA (21) 

(22) Date of filing of Application: 01/08/2003 (43) 



(54) Title of the invention: A LEVEL-MEASURING DEVICE OPERATING WITH MICROWAVES 

(51) International Classification : G 01 F 23/284 (71) 


(32) Priority Date : 14/02/2001 

(33) Name of priority country : EP 

(86) 


No. 

: PCT/EP02/00033 



No. 

: WO 02/065066 A1 



: NIL 



No. 

: NIL 



The invention relates to a level-measuring device which functions 

especially with microwave bursts and which is used to produce a 

measuring value (XH) representing the level inside a container 

(200). The level-measuring device comprises a transceiver (2) 

which is used to produce an intermediate frequency signal (ZF), 

which is influenced by the filling level, by means of a send signal 

(S2) and a receive signal (E2). The filling-level measuring device 

also comprises a converter element (1) which, when in operation, is 

controlled by the send signal (S2) and which injects especially 

pulsed transmission waves (S1) into the container (200), converting 

reflected echo waves (E1) from the filling material (201) into the 

receive signal (E2). The intermediate frequency signal (ZF) is fed to 

a control unit (3) of the filling-level measuring device and digitally 

stored in the form of a scanning sequence (AF) in a volatile data 

memory (33), whereby amplitude and phase information is also 

available upon determination of the filling level. The filling-level 

measuring device is thus able to measure the filling level in a very 

fast, highly accurate manner, down to the last millimeter. 

(FIG.: 1) 


(72) 


ENDRESS+HAUSER GMBH+CO. KG 


HAUPTSTRASSE 1, 

79689 MAULBURG, GERMANY. 


1. SPANKE DIETMAR 






(19) INDIA (21) 





APPARATUS FOR DETERMINIG THE FILING LEVEL OF A PRODUCT IN 

A CONTAINER 

(51) International Classification : G 01 S 13/88 (71) 

(31) Priority Document No. : 101 06 681.3 

(32) Priority Date : 14/02/2001 


(86) 


No. 

: PCT/EP01/14788 



No. 




: NIL 


(62) 


No. 

: NIL 



The invention relates to a device for determining the level of the 

contents (2) in a container (3). The aim of the invention is to realize 

a high-precision delay circuit (9). To this end, a delay circuit (9) is 

provided with the following elements: an emitting oscillator (14) 

that generates emitter pulses with an emitter frequency (f2); a 

sampling oscillator (15) that generates sampling pulses with a 

sampling frequency (f1), whereby the sampling frequency (f1) is 

lower than the emitter frequency (f2); a digital sampling circuit (17) 

that samples the emitter pulses with the sampling pulses; a 

regulating/control unit (16) that sets the frequency difference (f2 - 

f1) between the emitting oscillator (14) and the sampling oscillator 

(15) in order to obtain the predetermined translation factor. 

(FIG.: 1) 


(72) 







1. HEIDECKE FRANK 








(54) Title of the invention: MULTI-STAGE CENTRIFUGAL COMPRESSOR 

(51) International Classification : F 04 D (71) 


(32) Priority Date : 23/04/2001 



No. 

: PCT/US02/12593 



No. 

: WO 02/086324 A2 



: NIL 



No. 

: NIL 



A multi-stage centrifugal compressor multi-stage centrifugal 

compressor with an integral high-speed motor for compressing 

air has a variable speed permanent magnet motor having 

electronically commutated stator coils surrounding a rotor 

carrying permanent magnets, wherein there is a gap between the 

coils and the rotor. The rotor has a magnetic steel rotor shaft 

rotatably supported at each end by pressurized oil lubricated 

hydrodynamic bearings. The stator coils have a plurality of 

stator wires extending longitudinally along the stator and 

continuing around the ends of the stator to define end turns. The 

compressor also has a plurality of compressor impellers 

mounted to turn with the rotor shaft and cooler for cooling the 

bearings, rotor and stator coils comprising a pump for 

introducing cooled oil into the bearings, said bearing configured 

so that oil exiting from the bearings splashes over the supported 

ends of the shaft and splashes over the end turns of the stator 

coils. There is a passageway through the stator for introducing 

pressurized air within a gap between the stator and the rotor 

during start up to maintain a positive pressure within the gap 

thereby displacing oil from the gap. 

(FIG.: 4) 


(72) 


EARNEST PACIFIC LIMITED 


C/O. CITCO TRUST COMPANY 

LIMITED, LEEWARD ONE 

BUILDING, CORPORATE CENTRE, 

WEST BAY ROAD, 

P.O.BOX. 31106 SMB, GRAND 

CAYMAN, CAYMAN ISLANDS. 


1. HILL M. RAYMOND 

2. GRBIC MILOVAN R 








(54) Title of the invention: A BUILDING HEATING INSTALLATIONS 

(51) International Classification : F 24 D 13/04 

H 05 B 6/64 


(32) Priority Date : 29/03/2001 

(33) Name of priority country : EPO 

(71) 


No. 

: PCT/EP02/02495 



No. 

: WO 02/079697 A1 (72) 



: NIL 



No. 

: NIL 



The invention relates to a space heating system (3) comprising a 

first heating subsystem (4) with at least one first heat source (5) 

with an integrated heat source heat exchanger, heat transfer 

devices (12) mounted at a distance from the heat source (5) in 

only at least one room (11) of the building as the radiators with 

outer heat transfer surfaces (13) and pipe conduits (14, 15) as the 

flow pipes and return pipes between the heat source heat 

exchanger and the heat transfer devices (12). The pipe conduits 

(14, 15) of the heat source heat exchanger and the heat transfer 

devices (12) contain a flowable heat transfer medium. The space 

heating system (3) further comprises a second heating subsystem 

(16) with a second heat source and a heating control (18) with at 

least one temperature control and one switch unit for switching 

off or switching over the heating subsystems (4, 16) for an 

individual operation, or for switching on a heating subsystem in 

addition to the other heating subsystem for a common operation. 

The invention is further characterized in that the second heating 

subsystem (16) comprises a radiation heater with an electrically 

activatable coating as the radiation surface (17) that is directly or 

indirectly applied to at least part of the outer heat transfer 

surface (13) as a two-dimensional coating so that the heat 

transfer device (12) constitutes a component of both the first 

heating subsystem (4) as well as an integral support of the 

coating as the radiation surface (17) of the second heating 

subsystem (16). 

(FIG.: 1) 



MOLETHERM HOLDING AG 


DAMMSTRASSE 21, 

CH- 4502 SOLOTHURN, 

SWITZERLAND. 


1. REICHELT HELMUT 






(19) INDIA (21) 





A QUICK CONNECT COUPLING FOR CONNECTING A FLEXIBLE HOSE 

TO A FIXTURE 

(51) International Classification : F 16 L 19/02, 37/088 (71) 


(32) Priority Date : 09/03/2001 



No. 

: PCT/US02/07044 



No. 

: WO 02/073077 A1 (72) 



: NIL 


(62) 



No. 

: NIL 


A quick connect coupling for connecting a hose 

to a fixture of the type having a hose stem portion 

(11) having a hose insert (34), having a fixture 

portion 10 having a fixture connection portion 

(39), and having a joinder portion (20), said 

joinder portion (20) having a male connection 

portion (38) and a female connection portion 

(37), each of said male connection portion 38 and 

said female connection portion (37) adapted to 

join in a sealing and locking manner upon being 

pushed together, said coupling having threads 

and wrench mating flats 33 adapted to disconnect 

said hose from said fixture, characterized in that: 

said male connection (38) portion being a unitary 

structure having a leading support cylindrical 

surface (52), a following support 


THE GATES CORPORATION 


900 SOUTH BROADWAY, 

DENVER, COLORADO 80209, 



1. ADRIAN R. COOPER 

2. GEOFFREY R. KEAST 

3. RANDALL M. LEASURE 




cylindrical surface (54), and a transition surface 43 intermediate 

therein between, said leading support cylindrical surface 52 having a 

leading radius and said following support cylindrical surface 54 having 

a following radius, and said following radius being larger than said 

leading radius. 

(FIG.: 1) 




(19) INDIA (21) 





ARRANGEMENT AND METHOD FOR REDUCING BUILD-UP ON A 

ROASTING FURNACE GRATE 



(32) Priority Date : 09/03/2001 


(86) 


No. 

: PCT/FI02/00180 



No. 

: WO 02/072894 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 


OUTOKUMPU OYJ 





1. NYBERG JENS 

2. SIIRILA HEIKKI 

3. JARVI JUHA 




The present invention relates to an arrangement and method that help to reduce the build-up formed on the grate 

of a fluidized-bed furnace in the roasting of fine-grained material such as concentrate. The concentrate is fed into 

the roaster furnace from the wall of the furnace, and oxygen-containing gas is fed via gas jets under the grate in 

the bottom of the furnace in order to fluidize the concentrate and oxidize it during fluidization. Below the 

concentrate feed point, or feed grate, the oxygen content of the gas to be fed is raised compared with gas fed 

elsewhere using additional gas jets situated in the feed grate higher than the other jets. The extra jets of the feed 

grate are connected to their own gas distribution unit. 

(FIG.: NIL) 




(19) INDIA (21) 





METHOD AND SYSTEM FOR ENHANCED ACCESS TO A 

SUBTERRANEAN ZONE 

(51) International Classification : E 21 B 43/00, 43/30 (71) 


(32) Priority Date : 24/01/2001 


(86) 


No. 

: PCT/US02/01325 



No. 

: WO 02/059455 A1 



: NIL 


(62) 


No. 

: NIL 



A system for enhanced access to subterranean zone from the 

surface includes a well bore pattern (100) having a first well 

bore (104) extending from a surface well bore substantially 

defining a first end of the area in the subterranean zone to a 

distant end of the area. The pattern also includes a plurality of 

lateral well bores (110) extending outwardly from the first well 

bore. The distance from an end of a lateral well bore to the 

surface well bore may be configured to be substantially equal 

for each of the lateral well bores to facilitate forming the 

lateral well bores. The system and method may also include 

nesting two or more well bore patterns within the subterranean 

zone to provide uniform coverage of the zone. Additionally, 

the system and method may include multiple well bore patterns 

in communication within common surface well bore to reduce 

the surface area required for accessing the subterranean zone. 

(FIG.: 5) 


(72) 


CDX GAS, L.L.C. 


SUIT 380, 5485 BELTLINE ROAD, 

DALLAS, TX 75240-7656, USA. 


1. ZUPANICK JOSEPH A 






(19) INDIA (21) 



(51) International Classification : E 21 B 7/04, 43/30, 

43/00, 43/14 


(32) Priority Date : 30/01/2001 


(86) 


No. 

: PCT/US02/01320 



No. 




: NIL 


(62) 


No. 

: NIL 



A method and system for accessing subterranean zones 

from the surface includes a substantially vertical well bore 

(210) extending from the surface to a target zone (15), and 

an articulated well bore (230) extending from the 

substantially vertical well bore to the target zone. The 

articulated well bore diverges from the substantially 

vertical well bore between the surface and the target zone. 

The system also includes a well bore pattern (50) extending 

from the articulated well bore in the target zone operable to 

collect resources from the target zone. The system also 

includes a subsurface channel operable to communicate 

resources from the well bore pattern to the substantially 

vertical well bore. The system further includes a vertical 

pump (80) disposed in the substantially vertical well bore 

and operable to lift resources collected in the substantially 

vertical well bore to the surface. 

(FIG.: 10) 




METHOD AND SYSTEM FOR ACCESSING SUBTERRANEAN ZONES 

FROM A LIMITED SURFACE AREA 

(71) 

(72) 


CDX GAS, L.L.C. 


SUIT 380, 5485 BELTLINE ROAD, 

DALLAS, TX 75240-7656, USA. 


1. ZUPANICK JOSEPH A 

2. RIAL MONTY H 






(19) INDIA (21) 





PROCESS FOR THE PREPARATION OF A FOAMED PRODUCT AND A 

FROZEN CONFECTION 

(51) International Classification : A 23 L 1/0524 (71) 


(32) Priority Date : 26/02/2001 



No. 

: PCT/EP02/01212 



No. 

: WO 02/071870 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI 400 020, 



1. YVONNE EVELIEN 

BRUGGEMAN 

2. PETER RAVESTEIN 




Foamed products based on an aqueous composition comprising an oxidized ferulyated polymer are stable both 

during storage and after freezing and subsequent storage. A process for preparing these products is provided. 

(FIG.: NIL) 




(19) INDIA (21) 




(54) Title of the invention: METHODS FOR PREPARING CETP INHIBITORS 



(32) Priority Date : 30/04/2001 



No. 

: PCT/IB02/01214 



No. 

: WO 02/088085 A3 (72) 



: NIL 


(62) 



No. 

: NIL 



PFIZER PRODUCTS INC. 


EASTERN POINT ROAD, 

GROTON, CONNECTICUT 06340, 



1. DAVID BURNS DAMON 

2. ROBERT WAYNE DUGGER 

3. ROBERT WILLIAM SCOTT 




This invention relates to methods for preparing certain cholesteryl ester transfer protein (CETP) inhibitors IA or 

IB and intermediates related thereto. 

(FIG.: NIL) 




(19) INDIA (21) 





A PERSONAL CLEANSING COMPOSITION HAVING SOAP-LIKE 

RINSABILITY 



(32) Priority Date : 28/02/2001 



No. 




No. 

: WO 02/074252 A3 



: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI 400 020, 



1. TSAUR LIANG SHENG 

2. ARONSON MICHAEL PAUL 




The invention provides personal wash compositions with soap like rinsability. The composition contains a 

lathering surfactant and a specifically defined polymer/oil blend. 

(FIG.: NIL) 




(19) INDIA (21) 





PROCESS FOR MAKING A PERSONAL CLEANSING COMPOSITION 

HAVING DESIRABLE MOISTURIZING PROPERTIES 

(51) International Classification : A 61 K 7/50, 7/00 (71) 


(32) Priority Date : 28/02/2001 



No. 




No. 




: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI 400 020, 







The invention provides a process for making cleansing compositions having desirable moisturization properties 

by preparing structured liquid base, separately mixing oil and optional polymer to form mixture, mixing or 

injecting this mixture into the structured base and passing resulting composition through screen with openings 

larger than 30 micrometer. 

(FIG.: NIL) 




(19) INDIA (21) 


(54) Title of the invention: FLOW METER 

(51) International Classification : G 01 F 15/18, 25/00 (71) 


(32) Priority Date : 03/05/2001 

(33) Name of priority country : GREAT BRITAIN 

(86) 


No. 

: PCT/EP02/04637 



No. 

: WO 02/090897 A1 



: NIL 


(62) 


No. 

: NIL 



A flow meter incorporating thermal loss sensors and an 

installation adapter to provide known flow conditions 

upstream of the meter. The installation adapter is in the 

form of a tubular extension projecting from a flange 

which in use is sandwiched between a pipeline flange and 

a flow meter flange. The flanges are configured such that 

a passageway defined by the adapter extension is located 

in a predetermined position relative to the flow meter. 

The flow meter may comprise a sensor array supporting 

at least three sensors which are not in alignment, one of 

those sensors being located centrally within the flow 

meter and the others being distributed at equal distances 

around the central position. In use, normal readings may 

be taken from a single one of the sensors, the other 

sensors being used for initial calibration and subsequent 

calibration test purposes only. A comparison is made 

between the relative values of the outputs of the different 

sensors to identify sensor drift or potentially significant 

changes in flow conditions. 

(FIG.: 1) 




(72) 







1. GIMSON CHRIS 






(19) INDIA (21) 




(54) Title of the invention: INNER RACE IDLER PULLEY TENSIONER 

(51) International Classification : F 16 H 7/08 (71) 

(31) Priority Document No. : 09/805,069 

(32) Priority Date : 12/03/2001 



No. 

: PCT/US02/08186 



No. 

: WO 02/073066 A2 (72) 



: NIL 


(62) 



No. 

: NIL 


The invention comprises a tensioner having an inner race 

rotation idler pulley. The pulley having a web and a belt bearing 

surface connected to the web. The web is attached to an inner 

race of a bearing by a fastener. The pulley may be stamped out 

of sheet metal or of spun metal and may have a central hole for 

alignment with the central axis of the bearing. The outer race of 

the bearing is mounted to a pivot arm. The pivot arm comprises 

at least two pivot points for pivotably attaching the pivot arm to 

a mounting plate and a biasing member. The pivot points are 

contained within a periphery of the pulley. The biasing member 

urges the pivot arm and pulley against a belt to be tensioned. 

(FIG.: 3) 









1. ALEXANDER SERKH 








(54) Title of the invention: : DISPENSER WITH EFFERVESCENT BEVERAGE PRODUCT 

(51) International classification : B65D 83/32 

(31) Priority Document No : 


1. 01302000.3 

2. 0112473.4 

3. 0112757.0 

4. 0122150.6 

1. 05/03/2001 

2. 23/05/2001 

3. 25/05/2001 

4. 13/09/2001 

(33) Name of priority country : EUROPE, 

UNITED KINGDOM 




No 



: PCT/EP02/01810 

18/02/2002 

: WO 02/070372 A1 

: 

NIL 



No 

: NIL 






165/166 BACKBAY 

RECLAMATION, MUMBAI 400 

20, MAHARASHTRA, INDIA. 


1. FARR ROBERT 

2. NECMANIS MARK 




(57) Abstract: A beverage product that comprises a dispenser and a pressurised beverage. The dispenser has a container 

for holding the beverage and a valve. The beverage has a sparingly soluble effervescence inducing gas dissolved therein 

and is held under a gaseous pressure in the head space of the container that is sufficient to cause the beverage to be 

discharged from the dispenser as an effervescent fluid when the valve is open. 

(FIG.- NIL.) 




(19) INDIA (21) Application No.: 822/MUMNP/2003 


(54) Title of the invention: : EFFERVESCENT BEVERAGE IN A CONTAINER AND METHOD 

FOR DRINKING THE SAME 

(51) International classification : B65D 83/14 

(31) Priority Document No : 

1. 01302000.3 

2. 0112473.4 

3. 0112757.0 

4. 0122150.6 


1. 05/03/2001 

2. 23/05/2001 

3. 25/05/2001 

4. 13/09/2001 

(33) Name of priority country : EUROPE, 





No 



: PCT/EP02/02345 

28/02/2002 

: WO 02/070371 A3 

: 

NIL 



No 

: NIL 





HINDUSTAN LEVER HOUSE, 165/166 



INDIA. 


1. FARR ROBERT 

2. NICMANIS MARK 



Ordinance, 2004: YES/NO 

(57) Abstract: An effervescent beverage within a pressure resistant container with a discharge 

valve and having an effervescent gas dissolved therein is described. The beverage remains 

pressurized until consumed and may have a smooth and silky texture when a sparingly soluble 

gas is used. 


(FIG.- 1.) 

The Patent Office Journal 24.06.2005 17835 

A


(19) 




(54) Title of the invention: USE OF HOP COMPONENTS IN FOODS. 

(51) International Classification: A 23 L 1/30 (71) 




(86) 

05/04/2001 

EUROPE 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : The invention provides food products with 

anti-inflammatory and/or anti-ageing properties prepared by 

incorporating therein an effective amount of isoxanthohumol 

and/or xanthohumol. Isoxanthouhumol is especially preferred. 

Also provided is a method of administering isoxanthohumol 

and/or xanthohumol to persons in need of the intake of an antiinflammatory 

and/or anti-ageing component. Food products 

provided include spreads, dressings, mayonnaises, ice creams, 

cream alternatives, health bars, health drinks, sports drinks, 

chocolates, confectionery, bakery products, soups, cereals, 

sauces, fillings and coatings. 


(72) 






MUMBAI – 400 020, 



1. GREEN MARTIN R. 

2. RICHARD MARK 

3. TASKER MARIA C. 








(22) Date of filing of Application : 06/10/2003 (43) Publication Date: 24/06/2005 


(51) International Classification: B 63 B 35/32 (71) 




(86) 

SYSTEM FOR THE MASS RECOVERY OF SLICKS OF 

SPILT PETROLEUM PRODUCTS FLOATING ON THE SEA 

FOLLOWING SHIPPING INCIDENTS. 

NIL 

NIL 





(61) 

(62) 



Filed on N.A. 

Divisional to 




1. DEJOUX ANDRE 

2. SIRAGNA MARCEL 

3. FRANCATEL CLAUDE 


1. RUE DE FONTARABIE, 

75020 PARIS, FRANCE. 

2. 10, SENTIER DES BRILLANTS, 

92190 MEUDON, FRANCE. 

3. 13, RUE DE LILLE, 

75007 PARIS, FRANCE. 


(57) Abstract : The invention relates to a system for the mass recovery of petroleum 

products which is installed on a boat (1) that is specially designed to approach the oil 

slick to be recovered at 20 knots, said slick having been enclosed by a containment 

barrier comprising a skirt that prevents the petroleum from escaping underneath. The 

recovery system comprises a static ramp (10, 11) that extends into the sea to a 

sufficient depth in order to take account of very strong swells, the upper end (12) of 

said ramp being solidly connected to a dynamic decantation tank (2, 3) which is closed 

on top by means of a wall (4, 5). The boat loads the petroleum and water by means of 

the ramp (10, 11) into the tank thereof (2, 3) serving as a static water/petroleum 

separator, in which the oil slick (13), which has a lower density than water (14), floats 

on the water, thickening on top of the surface (15). The upper level (16) of the slick is 

always maintained below that (17) of the level of the sea by means of a centrifugal 

pump assembly (18) having an adequate capacity. Said pump assembly expels the 

water (14) into the sea so that petroleum and water can continue to be loaded. When 

the lower level of the slick (13) falls below the transfer pumps (19), benefiting from 

the gravitational pressure of the slick, said transfer pumps start up and push the slick, 

via a separation wall (6, 7), into a storage tank (8) for decanted oil, while the boat 

advances into the slick at a maximum speed of approximately six knots. 


- IDEM - 







(19) 


(22) Date of filing of Application : 06/10/2003 






(86) 


METHOD AND SYSTEM (EQUIPMENT) FOR OBTAINING 

ANIMAL FEED FROM EXTRACTION MEAL FROM SUNFLOWER 

SEEDS. 


GERMANY 




Publication No. WO02/080699 A2 

(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


WALTER ULRICH 


ASTERNWEG 17, 

40822 METTMANN, 

GERMANY. 


- IDEM - 

(57) Abstract : The invention relates to a method and a system for preparing 

waste-free extraction meal from the seeds of conventional sunflowers for animal 

feed for monogastrics or ruminants. The extraction meal from shell kernels and 

shells with adherent kernel parts is mechanically structured, chunks of extraction 

meal material are comminuted, kernel parts adhering to the shells are removed and 

the shells are coarsely comminuted while maintaining and improving the structure 

and the structured particles are separated into two fractions containing various 

amounts of crude proteins and crude fibers, one protein-rich fraction which is 

suitable for feeding monogastrics is obtained and one fraction containing crude 

fibers which is suitable for feeding ruminants is obtained, being subjected to a 

decomposition process in order to increase nutritive value and digestibility. 





( Figure: 1A ) 



(19) 




(51) International Classification: A 23 L 1/0524 (71) 




(86) 


PROCESS FOR MAKING A REDUCED - CALORIE FRUIT AND/OR 

VEGETABLE SPREAD. 

08/03/2001 

U.S.A. 

International Application : PCT/US02/06995 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


BOCABEAR FOODS, INC. 


2820 EDGEWOOD DRIVE RENO, 

NEVADA 89503, 

U.S.A. 


TOVES FRANCES ANN 




(57) Abstract : A process for making, or preparing, a reduced-calorie fruit and/or vegetable product including whole, 

natural fruit(s) and/or vegetable(s), or combinations thereof, having improved flavor, texture (e.g., mouth feel), color, 

and nutritional value as compared to fruit and/or vegetable spread products made with conventional processes. More 

particularly, the process of the present invention includes a pasteurization step, using a swept-surface heat exchanger, 

for making fruit and/or vegetable spread products having reduced caloric and sugar content and having increased 

soluble dietary fiber content. The minimal processing of the present process enables the produced fruit and/or 

vegetable spread products to retain flavor, texture, color, vitamins and other nutrients which are, typically, lost in 

traditionally-processed fruit and/or vegetable spread products. The process’ preferably use of squeeze tube packaging 

eliminates the need for cutlery in order to use or consume the fruit and/or vegetable spread products and serves to make 

the products more portable. 





(19) 




(51) International Classification: C 08 K 5/05 (71) 

(31) Priority Document No. : 

1) 09/860,005 2) 09/860,130 3) 09/860,140 


1) 17/05/2001 2) 17/05/2001 3) 17/05/2001 


(86) 


A FABRIC ARTICLE FOR WOVEN OR KNIT FABRIC AND A 

WOVEN OR KNIT FABRIC MADE THEREFROM. 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


MILLIKEN & COMPANY 


920 MILLIKEN ROAD, 

SPARTANBURG, SC 29303, 



1. MORIN BRIAN G. 

2. MEHL NATHAN A. 

3. PARKS WILLIAM S. 

4. COWAN MARTIN E. 




(57) Abstract : This invention relates to improvements in heat 

and moisture-shrink problems in polypropylene fibers. Such 

fibers require the presence of compounds that quickly and 

effectively provide rigidity to the fiber after heat-setting. These 

compounds include structures that nucleate polymer crystals 

within polypropylene after exposure to sufficient heat to melt 

the polymer and allowing the melt to cool. The compounds must 

nucleate polymer crystals at higher temperatures than the 

polypropylene without the nucleating agent during cooling. 

Thus, the "rigidifying" nucleator compounds provide nucleation 

sites for polypropylene crystal growth. After drawing the 

nucleated composition into fiber form (11), the fiber is exposed 

to sufficient heat to grow the crystalline network (26), thus 

holding the fiber in a desired position. The preferred 


"rigidifying" compounds include dibenzylidene sorbitol based 

compounds, as well as less 

preferred compounds, such as sodium benzoate, certain sodium and lithium phosphate salts (such as sodium 2,2'methylene-bis-(4,6-di-tert-butylphenyl)phosphate). 




(19) 








(86) 


A PROCESS FOR THE STEREOSELECTIVE PREPARATION OF 

INSECTICIDE 6,7,8,9,10-10-HEXAHALO-1,5,5A,6,9,9A-HEXAHYDRO- 

6,9-METHANO-2,4,3-BENZODIOXATHIEPIN-3-OXIDE. 

NIL 

NIL 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


EXCEL INDUSTRIES LIMITED 


184/87, SWAMI VIVEKANAND ROAD, 

JOGESHWARI, MUMBAI – 400 102, 



1. SHROFF ASHWIN CHAMPRAJ 

2. PUROHIT ABHIJIT PREMVALLABH 

3. VADODARIA SANJAY DHIRAJLAL 




(57) Abstract : A process for the stereoselective preparation of insecticide 6,7,8,9,10,10-hexahalo-1,5,5a,6,9,9ahexahydro-6,9-methano-2,4,3-benzodioxathiepin-3-oxie 

of the general formula 1: wherein X is a halogen such as 

fluorine, chlorine or bromine. The process comprises reacting 1,4,5,6,7,7-hexahalo-5-norbornene-2,3-dimethanol of the 

general formula IV: wherein X is as defined above, with a cyclic sulfite ring forming reagent optionally in an inert 

organic solvent at ambient to 139 DEG C, wherein the reaction is carried out in the presence of a stereo isomer 

directing agent comprising an isomer of the compound of the formula I different from the desired isomer. The molar 

ratio of the stereoisomer directing agent to the dimethanol compound of the formula IV is at least 0.07. 





(19) 




(54) Title of the invention: A PROCESS FOR PREPARING A COMPOUND OF FORMULA I 





(86) 


U.S.A. 

International Application : PCT/IB02/01876 




(61) 

(62) 




Filed on N.A. 

Divisional to 



(72) 




EASTERN POINT ROAD, GROTON, 

CONNECTICUT 06340, 



1. BERTINATO PETER 

2. BLIZE ALAN ELWOOD 

3. BRONK BRIAN SCOTT 

4. CHENG HENGMIAO 

5. HUATAN HIEP 

6. LI JIN 

7. CLIVE PHILIP MASON 




The invention relates to triamide MTP/ApoB inhibitors of the formula 1, wherein R-R are as defined in the 

specification, as well as pharmaceutical compositions and uses thereof, and processes for preparing the compounds. The 

compounds of the invention are useful for the treatment of obesity and lipid disorders. 





(19) 








(86) 


A DRY PROCESS FOR MANUFACTURING A PHARMACEUTICAL 

COMPOSITION HAVING UNIFORM DRUG DISTRIBUTION AND 

POTENCY. 

01/05/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 








GIERER DANIEL SCOTT 




(57) Abstract : A method for manufacturing a pharmaceutical composition having uniform drug distribution and 

potency is described which utilizes silicon dioxide to reduce the loss of active ingredient during the manufacturing 

process. The method is particularly useful for the manufacture of low dosage tablet compositions. 


Total Pages : 24. 



(19) 






2. 60/343,733 



(86) 


METHOD FOR PREPARING A LIQUID PHARMACEUTICAL 

COMPOSITION. 

1. 25/05/2001 

2. 25/10/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


WARNER-LAMBERT COMPANY 

LLC. 


201 TABOR ROAD, 

MORRIS PLAINS, 




1. KULKARNI NEEMA MAHESH 

2. SCHNEIDER MICHAEL 

3. SILBERING STEVEN BERNARD 

4. MEYER-WONNAY HANS RICHARD 

5. SANII-YAHYAI NAHID 




(57) Abstract : A liquid pharmaceutical composition of a GABA analog comprising at least one polyhydric alcohol 

containing 2 to 6 carbon atoms having a pH of about 5.5 to about 7.0 and additionally a two-component liquid 

pharmaceutical composition comprising a first component comprising a powder mixture comprising a GABA analog 

and a solid polyhydric alcohol, and a second component comprising a liquid base are described, as well as methods to 

prepare the compositions and a method for treating cerebral diseases, including epilepsy, faintness attacks, hypokinesia 

and cranial traumas, neurodegenerative disorders, depression, mania and bipolar disorders, anxiety, panic, 

inflammation, renal colic, insomnia, gastrointestinal damage, incontinence, pain, including neuropathic pain, muscular 

pain, skeletal pain, and migraine using a therapeutically effective amount of the pharmaceutical compositions. 








(51) International Classification: G 01 C (71) 




(86) 

MEASURING AND LOCATING SYSTEM USING BASES THREE 

AND NINE AND CORRESPONDING USES. 

05/04/2001 

FRANCE 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


SEGUR PATRICK 


33 RUE GALILEE, 

F-75116 PARIS, 

FRANCE. 


- IDEM - 

(57) Abstract : In order to locate a spatial zone on a surface, said system uses a 

division of the surface into zones wherein: the surface is divided into three parts in 

two directions, that is into nine zones called first rank zones whereto a respective 

number from 1 to 9 is assigned; each zone of rank n is divided likewise into nine 

zones of rank n+1 whereto a respective number from 1 to 9 is assigned, a zone of 

rank n being located by a locating sequence comprising n figures containing the 

number of the zone to be located, and the numbers of all the zones of lower rank 

containing the zone to be located; said system comprising means to determine the 

locating sequence of a zone of rank n wherein is a zone Z to be located, n being 

the maximum value such that the surface of the zone Z is included in the zone of 

rank n, and means for manipulating such a sequence. 

FIG. 6: A LONGITUDE B LATITUDE 1 CENTRE 2 NORTH 3 EAST 4 SOUTH 

5 .WEST 6 NORTH-WEST 7 NORTH-EAST 8 SOUTH-EAST 9 SOUTH-WEST 





( Figure: 06 ) 



(19) 




(51) International Classification: A 64 B (71) 




(86) 


METHOD AND SYSTEM FOR MONITORING THE POSITION OF A 

TOOTH BRUSH RELATIVE TO TEETH OF A SUBJECT. 

17/04/2001 

UNITED 

KINGDOM 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 






MUMBAI – 400 020, 



1. SAVILL DEREK GUY 

2. TRELOAR ROBERT LINDSAY 




(57) Abstract : A method is proposed for analyzing the usage of a toothbrush made by a subject. The position of the 

toothbrush is monitored using a position sensor on the brush, and the position of the teeth is monitored by a position 

sensor mounted in a known fixed relation to the teeth. The resultant data is used to find the relative positions of the 

toothbrush and teeth over time. Statistical analysis of this data permits the identification of habitual brushing failures 

by subjects of the toothbrush. The toothbrush may transmit the output of its position sensor to a data analysis unit as a 

wireless signal. The toothbrush may also be provided with further sensors, such as pH and pressure sensors, the output 

of which is used in the statistical analysis to enrich the results. 





(19) 








(86) 


READILY PLODDABLE SOAP BARS COMPRISING ALPHA- 

HYDROXY ACID SALTS. 

18/04/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 






MUMBAI – 400 020, 



1. FARRELL TERENCE JAMES 

2. NUNN CHARLES CRAIG 

3. FRANCIS KEITH ANTHONY 




(57) Abstract : The invention relates to composition comprising soap which, when used with at least 3% 

monoglyceride and or free fatty acid, allows incorporation of desirable a-hydroxy acid salts while retaining good 

ploddability properties. In another embodiment, the invention relates to process for making such bars. 





(19) 








(86) 


DETERGENT BAR COMPOSITIONS COMPRISING ANIONIC 

SURFACTANT, SOAP, HYDROXY ACID SALT AND FILTER. 

18/04/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 






MUMBAI – 400 020, 



1. McFANN GREGORY JAY 

2. NUNN CHARLES CRAIG 




(57) Abstract : The invention discloses bars and process for making bars comprising synthetic anionic, fatty acid soap 

and hydroxy acid salt wherein the bar can be extruded at minimum rates and wherein the bar and process are defined 

ratio of hydroxy acid salt to calcite filler. 





(19) 



(54) Title of the invention: ENERGY GUIDING CHAIN. 

(51) International Classification: F 16 G 13/16 (71) 



23/04/2001 


(86) 

International Application : PCT/DE02/01407 




(61) 

(62) 



Filed on N.A. 

Divisional to 




(72) 


IGUS SPRITZGUSSTEILE FUR DIE 

INDUSTRIE GMBH 


SPICHER STR. LA, 

51147 KOLN, GERMANY. 


1. HERMEY ANDREAS 

2. BLASÉ FRANK 

3. BLASÉ GUNTER 




(57) Abstract : The invention relates to an energy drag chain for 

guiding tubes, cables or the like, comprising a number of chain 

members (2). Neighboring chain members are hinged to each 

other and are provided with flat links (3) with inner and outer 

lateral faces and front faces that are perpendicular thereto and 

substantially parallel to the longitudinal direction of the chain. At 

least some of the chain members have at least one crossbar (4a, 

4b) interlinking the flat links and the hinged joint of neighboring 

chain members is disposed on the front faces of the flat links. 

The energy drag chain can be displaced while forming a lower 

strand (5), a deflection zone (6) and an upper strands (7). The 

aim of the invention is to provide an energy drag chain with 

hinged joints that are disposed between the front faces of the flat 

links of the chain that can be displaced with little wear and little 

friction and that is simple and inexpensive in production. To this 

end, the chain members (1) are configured as elastically 


deformable joint elements (8) that are produced as separate 

components and that 

extend at least partially or preferably exclusively between the inner and outer lateral faces of the flat links (3). The joint 

elements (8) can be disposed in laterally open recesses of the flat links. 




(19) 








(86) 


A SOAP BAR COMPRISING TRIGLYCERIDES AND A PROCESS 

FOR MAKING SAME. 

26/04/2001 

U.S.A. 

International Application : PCT/EP02/04245 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 






MUMBAI – 400 020, 



1. SHAFER GEORGIA LYNN 

2. MASSARO MICHAEL 

3. YAROVOY YURIY 

KONSTANTINOVICH 

4. LANZA WILLIAM 




(57) Abstract : The invention relates to soap bars comprising 6% to 13% triglyceride oils wherein said bars 

simultaneously have post processing properties and maintain good lather. In a second embodiment, the invention 

relates to a process of making predominantly soap bars having noted properties comprising adding 6 to about 13% by 

wt. triglyceride oil(s) at finishing stage post crystallization. 





(19) 



(54) Title of the invention: FABRIC CARE COMPOSITIONS. 





(86) 

30/04/2001 

EUROPE 





(61) 

(62) 



Filed on N.A. 

Divisional to 




(72) 






MUMBAI – 400 020, 



1. BARBUZZI ELENA MARIA 

GABRIELLA 

2. JARVIS ANTHONY NICHOLAS 

3. WHILTON NICOLA 




(57) Abstract : A method of treating fabric comprising the step of applying to the fabric a fabric treatment composition 

comprising a coated particles comprising: a solid core having a D3,2 average particle size in the range from 10 to 700 

nm, and a coating of silicone polymer covalently bonded to the solid core. 





(19) 



(54) Title of the invention: LINEAR GUIDE. 

(51) International Classification: F 16 C 29/02 (71) 




(86) 

20/04/2001 

GERMANY 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : The invention relates to a linear guide 

consisting of a rail (1) with several tracks (2) and a cradle (3), 

which comprises at least one sliding element (4) that lies 

opposite the tracks (2), said element having an inclined surface 

(5) on the side facing away from the rail (1). Between the 

sliding element (4) and the cradle (3), the guide is provided 

with a displaceable actuating element (6), one surface (7) of 

which lies on the inclined surface (5) of the sliding element (4) 

in such a way that it can be displaced. To automatically adjust 

the bearing play, the actuating element (6) is pre-tensioned 

against the inclined surfaced (5) of the sliding element 


(72) 


IGUS SPRITZGUSSTEILE FUR DIE 

INDUSTRIE GMBH 


SPICHER STR. LA, 

51147 KOLN, 

FEDERAL REPUBLIC OF GERMANY. 


MOSHAMMER HORST 





(4) in such a way that a force component is produced on the sliding element (4) perpendicular to the tracks (2) that lie 

opposite said sliding element (4). In addition, the adjacent surfaces (7, 5) of the actuating element (6) and the sliding 

element (4) have a corresponding stepped configuration, so that the steps of the relevant surface (7) of the actuating 

element (6), as a result of the pre-tensioning of the latter, can slide over the steps of the inclined surface (5) of the 

sliding element (4) that is displaced in the direction of the tracks of the rail (1), with a corresponding amount of play. 




(19) 








(86) 


AN IMPROVED PROCESS FOR PREPARATION OF ANTI- 

TUBERCULAR PHARMACEUTICAL COMPOSITION IN FIXED 

DOSE OF FOUR DRUGS. 

NIL 

NIL 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


LUPIN LABORATORIES LIMITED. 


159, C.S.T. ROAD, KALINA, 

SANTACRUZ (EAST), 

MUMBAI – 400 098, 



1. SEN HIMADRI 

2. JINDAL KOUR CHAND 

3. DEO KISHOR DATTATRAY 

4. GANDHI KRISHNAKANT 

TULSIRAM 




(57) Abstract : An improved process for preparation of a composition comprising fixed dose combination (FDC) of 

four anti-tubercular drugs viz. rifampicin, isoniazid, pyrazinamide and ethambutol hydrochloride, which improves the 

dissolution of poorly soluble drug rifampicin and hence improve its bioavailability. It further provides an improved 

process for preparation of a composition comprising fixed dose combination (FDC) of four anti-tubercular drugs viz. 

rifampicin, isoniazid, pyrazinamide and ethambutol hydrochloride, which improves the dissolution of poorly soluble 

drug rifampicin and hence improve its bioavailability, without use of a surfactant. 





(19) 








(86) 


A PROCESS FOR MANUFACTURING A PHARMACEUTICAL 

FORMULATION IN SODIUM PHENYTOIN DOSAGE FORM. 

15/05/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


WARNER-LAMBERT COMPANY 

LLC 


201 TABOR ROAD, 

MORRIS PLAINS, 




1. CROTTS GEORGE HARLAND III 

2. FESSEHAIE MEBRAHTU 

GHEBRETENSAE 

3. GADIRAJU SRINIVAS RAJU 

4. GAWEL JOHN JOSEPH 

5. GHEBRE-SELLASSIE ISAAE 

6. SHETH ASHLESH KALYANBHAI 




(57) Abstract : A process for the roller compaction and manufacture of a pharmaceutical formulation comprises the 

steps of adding sodium phenytoin to a vessel of a blender and adding at least one excipient to the vessel. The mixture is 

blended and transferred to a roller compactor, where pressure is applied to the blend of sodium phenytoin and excipient. 

Next, the resultant compaction is milled to form a granulation, which is blended a second time and is suitable for further 

processing into a dosage form. Preferably, the excipients include magnesium stearate, sugar, lactose monohydrate, and 

talc. In an alternative embodiment, talc is added immediately prior to the granulation being blended for a second time. 





(19) 

INDIA (21) Application No: 1006/MUMNP/2003 A 



(54) Title of the invention: METHOD AND DEVICE FOR GENERATING OZONE. 

(51) International Classification: C 01 B 13/11 (71) 




(86) 

26/05/2001 

GERMANY 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : The invention relates to a method for 

generating ozone from gases containing oxygen. The ozone is 

generated by silent electric discharge in an installation 

comprising at least two gaps, which are traversed by the gas, 

each of said gaps being formed between an electrode and a 

dielectric that separates each gap from an additional electrode. 

According to the invention, the restriction of the volumetric 

flow of the gas of at least one gap is controlled. 


(72) 


WEDECO GESELLSCHAFT FUR 

UMWELTTECHNOLOGIES GMBH 


UNGELSHEIMER WEG 6, 

D-40472 DUSSELDORF, 

BUNDESREPUBLIK DEUTSCHLAND, 

GERMANY. 


1. BILLING ERNST MARTIN 

2. FIEKENS RALF 

3. HOFER UWE 







(19) 




(51) International Classification: F 03 D 3/04 (71) 




(86) 


A WIND POWER ACCUMULATING POWER GENERATING 

METHOD USED IN A POWER GENERATING SYSTEM. 

12/04/2001 

CHINA 

International Application : PCT/CN02/00251 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 

(57) Abstract : The present invention relates to the method and equipment 

of wind power generation, specially in the wind-collecting power generation 

method and equipment of the present invention, the wind-collecting device 

of the power generation tower is used to guide and accumulate airflow, and 

augment airflow rotation force and the arm of rotation force acted on the 

wind wheel to improve the power output. In the present invention, the 

guiding device is used to minish air resistance acted on the wind wheel that 

is against the wind; and empennage device is used to adjust automatically 

wind-collecting direction. The wind-collecting device is of arbitrary shape, 

and can be moved, rotated or shape-changed, and its inlet transverse section 

area is greater than the outlet one, so strong airflow can still be generated at 

the outlet to drive the wind wheel on the power generation tower under puny 

natural airflow. One kind of the power generation tower is fixed type; the 

other one can be moved from one place to another. The axis of the tower is 

perpendicular to the ground. The tower has a rotating curved surface or a 

cylindrical surface, and the electric power is generated by the rotation of 

couples of or hundreds of wind wheels installed flatly on the tower from the 

top down. 



HUANG CHIENWEN 


2 ND FLOOR, NO. 8, GUO-TAI ST., 

ZHONG-LI, TAO-YUAN XIAN, 

TAIWAN, CHINA. 


- IDEM - 




( Figure: 06 ) 



(19) 




(54) Title of the invention: A DAMPING MECHANISM USED IN A TENSIONER. 

(51) International Classification: F 16 H 7/12 (71) 




(86) 

18/05/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A damping mechanism used in a tensioner for 

tensioning a power transmission belt including a damping 

plate having a friction surface, at least one ramp surface and 

first and second contact points for operatively connecting a 

spring whereby the spring torque applied to damping 

mechanism in combination with a reactive force at the pivot 

surface generates a normal force. 


(72) 








1. SERKH ALEXANDER 







(19) 




(51) International Classification: A 01 M 7/00 (71) 

(31) Priority Document No. : 1. 101 23 301 

2. 102 21 948.6 



(86) 


METHOD AND SYSTEM FOR VOLUME- SPECIFIC TREATMENT 

OF GROUND AND PLANTS. 

1. 14/05/2001 

2. 13/05/2002 

GERMANY 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : The invention relates to a method 

and system for volume-specific treatment of 

ground and plants as required. The aim of the 

invention is to improve a method and system as 

above, such that the distribution of plants is 

scanned with complete spatial coverage and the 

treatment of the ground or plant condition is 

efficiently controlled, by simultaneously taking 

account of morphological, plant physiological, 

equipment performance and specific local 

properties. 


(72) 


KUMMEL, KNUT 


HOHENZOLLERN, STRASSE 11, 

12307 BERLIN, GERMANY. 


- IDEM - 







(19) 




(51) International Classification: C 07 D 401/06 (71) 




(86) 


A PROCESS FOR PREPARING A 4-[PHENYL-PIPERIDIN-4- 

YLIDENE-METHYL)-BENZAMIDE DERIVATIVES. 

18/05/2001 

SWEDEN 

International Application : PCT/SE02/00953 




(61) 

(62) 



Filed on N.A. 

Divisional to 




ASTRAZENECA AB 


S – 151 85 SODERTALJE, 

SWEDEN. 


1. BROWN WILLIAM 

2. WALPOLE CHRISTOPHER 




(57) Abstract : Compounds of general formula I R 1 is selected from any one of phenyl, pyridinyl, pyrroloyl, thienyl, 

furanyl, imidazolyl, triazolyl, thiazolyl and pyridine N-oxide; where each R 1 phenyl ring and R 1 heteroaromatic ring may 

optionally and independently be further substituted by 1, 2 or 3 substituents selected from straight and branched C1-C6 

alkyl NO2, CF3, C1-C6 alkoxy, chloro, fluoro, bromo, and iodo. The substitutions on the phenyl ring and on the phenyl 

ring and on the heteroaromatic ring may take place in any position on said ring systems; are disclosed and claimed in the 

present application, as well as salts and pharmaceutical compositions comprising the novel compounds and their use in 

therapy, in particular in the management of pain, anxiety and functional gastrointestinal disorders. 





(19) 



(54) Title of the invention: COSMETIC CREAM CLEANSER. 





(86) 

11/05/2001 

U.S.A. 





(61) 

(62) 




Filed on N.A. 

Divisional to 




(72) 






MUMBAI – 400 020, 



1. CROTTY BRIAN ANDREW 


3. CHENEY MICHAEL CHARLES 




A cosmetic cream cleansing composition is provided based on the presence of a silicate, a crosslinked carboxyvinyl 

polymer, a silicone copolyol sulfosuccinate and a carrier. The composition has a viscosity from 20,000 to 500,000 

centipoise. The combination of components achieves a product of good viscosity, pleasant skinfeel, rich lather and phase 

stability. 







(54) Title of the invention: TRANSDUCER OF THE VIBRATION TYPE. 

(51) International Classification: G 01 F 1/84 (71) 


(32) Priority Date : 23/05/2001 

(33) Name of priority country : E.P.O. 

(86) International Application : PCT/EP02/05276 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


ENDRESS+HAUSER FLOWTEC AG 


KAGENSTRASSE 7, 

CH-4153 REINACH, 

SWITZERLAND. 


1. DRAHM WOLFGANG 

2. RIEDER ALFRED 

3. BITTO ENNIO 

4. LORENZ RAINER 

5. SCHUTZE CHRISTIAN 

6. WENGER ALFRED 

7. FUCHS MICHAEL 




(57) Abstract : The transducer comprises a curved measuring 

tube (10), which vibrates in operation, for guiding the fluid and a 

counter-vibrator (20), which oscillates in counter-phase during 

operation and is essentially parallel to the measuring tube (10). 

The measuring tube (10) and the counter-vibrator (20) are 

mechanically coupled to each other by means of a coupling (31) 

on the inlet side and a coupler (32) on the outlet side. The 

measuring tube (10) communicates with the fluid-guiding 

pipeline by means of a inlet tube piece (12) opening out on the 

inlet side and an outlet tube piece (12) opening out on the outlet 

side. An exciter arrangement (40) for the transducer induces 

( Figure : 1a & 1b ) 

the 

measuring tube (10) and the counter-vibrator (20) to vibrate at an excitation frequency (fexc), whilst a sensor arrangement 

(50) records vibrations of the measuring tube (10) at the inlet and outlet ends. An inner piece, formed from at least the 

measuring tube (10), the counter-vibrator (20), the exciter arrangement (40) and the sensor arrangement (50) oscillates in 

operation about a longitudinal axis (A1) of the transducer, running essentially with the inlet and outlet tube pieces (11, 

12) and thus also causes a rotation of the coupler (31, 32) about the longitudinal axis (A1) and at least partly an 

essentially torsional, elastic deformation of the inlet and outlet tube pieces (11, 12). In order to allow an oscillation of the 

inner piece with a weak rotation, at least the coupler (31) is tuned to a torsional stiffness for the inlet tube piece (11) and 

at least the coupler (32) is tuned to a torsional stiffness for the outlet tube piece (12) in such a way that an inlet-side 

inherent characteristic torsional mode for the coupler (31) and inlet tube piece (11) has a characteristic frequency (f1) 

almost the same as the exciter frequency (fexc) and an outlet side inherent characteristic torsional mode for the coupler 

(32) and outlet piece (12) as a characteristic frequency (f2) essentially the same as the characteristic frequency (f1). The 

transducer is thus dynamically well balanced in operation over a wide fluid density range, despite the use of only one 

curved measuring tube. 




(19) 




(51) International Classification: C 07 D 243/02 (71) 

(31) Priority Document No. : 01 07458 



(86) 


PROCESS FOR PREPARING CYCLIC NUCLEOTIDE 

PHOSPHODIESTERASE INHIBITORS. 


FRANCE 


No. and Filing Date : 07/06/2002 



(61) 

(62) 




Filed on N.A. 

Divisional to 



The invention concerns novel benzodiazepinone derivatives and 

their uses in therapy particularly for treating pathologies involving 

the activity of a phosphodiesterase of cyclic nucleotides. The 

invention also concerns methods for preparing them and novel 

synthesis intermediates. The inventive compounds more 

particularly correspond to general formula (I). 


Total Pages : 

(72) 


NEURO3D 


130, RUE DE LA MER ROUGE, 

68200 MULHOUSE, 

FRANCE. 


1. BOURGUIGNON JEAN-JAEQUES 

2. LAGOUGE YAN 

3. LUGNIER CLAIRE 

4. KLOTZ EVELINE 

5. MACHER JEAN-PAUL 

6. RABOISSON PIERRE 

7. SCHULTZ DOMINIQUE 






(19) 




(54) Title of the invention: A PROCESS OF MAKING PHARMACEUTICAL COMPOSITIONS. 

(51) International Classification: A 01 N 63/00 (71) 




(86) 

15/05/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


KIBOW BIOTECH, INC. 


3624 MARKET STREET, 

SUITE 522, PHILADELPHA, 

PENNSYLVANIA 19104, 

U.S.A. 


1. RANGANATHAN NATARAJAN 

2. DICKSTEIN JACK 

3. MEHTA RAJ 




(57) Abstract : Microencapsulated and/or enteric coated composition containing a mixture of probiotics, prebiotics and 

ammoniaphilic bacteria with high urease activity with or without sorbents with specific adsorption afffinities for uremic 

toxins such as creatinine, uric acid, phenol, indoles, middle molecular weight molecules and inorganic phosphate and 

water absorbents are provided. Also provided are methods of allevating symptoms of uremia in a patient which comprises 

administering orally to a patient suffering from uremia a microencapsulated and/or enteric-coated composition. 





(19) 




(54) Title of the invention: MOBILE ZINC CATHODE STRIPPING SYSTEM. 


(31) Priority Document No. : 2,349,394 



(86) 

30/05/2001 

CANADA 

International Application : PCT/CA02/00790 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A mobile zinc stripping device for stripping zinc 

from cathodes comprising a moveable base frame, a cathode 

support frame to support the cathodes during stripping, a stripping 

assembly for stripping the zinc sheets from the cathodes and at 

least one power source for powering the stripping assembly. The 

stripping assembly includes a lateral stripper for separating an 

upper edge of a zinc sheet from each of the cathodes, the lateral 

stripper being adapted to bias away from the cathode immediately 

upon entering between the zinc sheet and the cathode, and a 

scraping device for completing removal of the sheet from each 

said cathode. The device also includes a cathode cleaner and a 

bottom up stacker assembly for stacking zinc sheets. 


(72) 


1. OUTOKUMPU TECHNOLOGY LTD 

2. ASTURIANDA DE ZINC S. A. 


1. P.O. BOX 655, BURLINGTON, 

ONTARIO L7R, CANADA, 

CANADIAN COMPANY. 

2. SAN JUAN DE NIEVA APDO, 

178, E-33400 AVILES, 

ASTURIAS, SPANISH COMPANY. 


1. SMITH BARRY JOHN 

2. ASENSIO LEOPOLD ESCOBEDO 

3. BOSSCHER JAN 







(19) 




(51) International Classification: H 01 Q 3/00 (71) 

(31) Priority Document No. : 1. 2001/36872 

2. 2001/50237 



(86) 


ANTENNA FOR PORTABLE WIRELESS COMMUNICATION 

APPARATUSES. 

1. 27/06/2001 

2. 21/08/2001 

KOREA 

International Application : PCT/KR02/01228 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : Disclosed herein is an antenna for portable 

wireless communication apparatuses. The antenna for portable 

wireless communication apparatuses includes an antenna 

element provided on its outer surface with a conductor on 

which a plurality of openings are formed. The outer portion of 

the interior of the conductor is filled with a dielectric material. 

This antenna element is connected in parallel with a linear 

radiator in an insulated state, thereby radiating electromagnetic 

waves and at the same time being capable of adjusting the 

radiated amount and direction of the electromagnetic waves. 


(72) 


E. M. W. ANTENNA CO., LTD. 


137-1, OJEON-DONG, 

UIWANG-SI, 437-819 GYEONGGI-DO, 

REPUBLIC OF KOREA. 


1. RYOU BYUNG-HOON 

2. SUNG WEON-MO 







(19) 




(51) International Classification: B 27 D 1/08 (71) 




(86) 


METHOD FOR PRODUCING A THREE-DIMENSIONALLY 

FORMED BODY. 

17/05/2001 

GERMANY 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


ACHIM MOLLER 


MAX-SACHS-STRASSE 32, 

01157 DRESDEN, 

GERMANY. 


- IDEM - 




(57) Abstract : The invention relates to a method for the production of a distinctively three-dimensionally formed, thinwalled, 

bowl-shaped body (three-dimensional body) or for coating distinctively three-dimensionally formed structural 

components made of different materials such a wood, wood-derived products, plastic material, cast aluminum, etc., said 

method being carried out place in several steps. The two or three-dimensional elements to be formed are initially cut to 

the required processing size. In the case of multilayered parts to be shaped, the two-dimensional and three-dimensional 

surface elements to be formed are positioned in a stack for the forming process and optionally fixed temporarily in their 

position. An individual three-dimensional surface element is thus produced, said element being made of wood (woodveneer), 

laminated wood or a composite consisting of wood and one or more surface materials such as plastic films or a 

nonwoven. The single or multilayered surface elements are then formed sectionwise or completely, wherein the form 

change occurs by shear deformation on the surface of all corresponding surface elements and simultaneous, multiaxial 

flexion deformation of the surface elements in the area of the active deformation zone is produced. 





(19) 




(51) International Classification: B 27 H 1/00 (71) 




(86) 


METHOD FOR THE PRODUCTION OF A 

THREE-DIMENSIONAL, FLEXIBLY DEFORMABLE SURFACE 

ELEMENT. 

17/05/2001 

GERMANY 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


ACHIM MOLLER 


MAX-SACHS-STRASSE 32, 

01157 DRESDEN, 

GERMANY. 


- IDEM - 




(57) Abstract : The invention relates to a method for the 

production of a three-dimensional, flexibly deformable surface 

element made of wood or a wood composite material for 

finishing layered, three-dimensional formed parts or for coating 

three-dimensional formed parts. A work piece made of wood, 

laminated wood or a wood composite material and one or more 

additional surface materials are used to this end, the thickness of 

which is at least 5 % bigger than the thickness of the 3D surface 


element to be produced. Narrow grooves spaced from one another are made in the work piece, wherein the depth of the 

groove is bigger or equal to the thickness of the 3D surface element and smaller than the thickness of the work piece. The 

fraction of the work piece that goes beyond the thickness of the 3D surface element to be produced is then separated from 

the remaining 3D surface element or is treated in such a way that, at least temporarily, no solid cohesion of the splines of 

the future 3D surface element that have been separated by the grooves exists. The areas of the work piece that have been 

divided from one another by the grooves are fixed to one another and/or to a support by a cross joint before, during or 

after separation from the work piece. 




(19) 



(54) Title of the invention: DAMP CLEANSING WIPE. 





(86) 

14/05/2001 

U.S.A. 

International Application : PCT/EP02/05068 




(61) 

(62) 



Filed on N.A. 

Divisional to 




(72) 






MUMBAI – 400 020, 








(57) Abstract : A disposable substantially damp cleansing article is disclosed having a cleansing composition 

impregnated onto a flexible substrate such as a non-woven cloth. The impregnated compositions include lathering 

surfactants and water, the compositions having a viscosity ranging from about 50 to about 300,000 centipoise. Amounts 

of water range from greater than 15 % to no higher than 40 % by weight of the total article. Speed of lather formation and 

foam volume increases within the window of the stated viscosity and water range. 





(19) 



(54) Title of the invention: DAMP CLEANSING WIPE. 





(86) 

14/05/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 




(72) 






MUMBAI – 400 020, 



1. LEE JAE 



4. CHENEY MICHAEL CHARLES 




(57) Abstract : A disposable substantially damp cleansing article is disclosed having a cleansing composition 

impregnated onto a flexible substrate such as a non-woven cloth. The impregnated compositions include lathering 

surfactants and water, and a water-binding agent resulting in a composition having a water activity less than 0.977 but no 

lower than 0.001. Amounts of water range from greater than 15% to no higher than 40% by weight of the total article. 

Speed of lather formation and foam volume increases within the window of the stated water activity and water range. 





(19) 



(54) Title of the invention: FABRIC CARE COMPOSITION. 


C 11 D 3/14 




(86) 

15/05/2001 

EUROPE 





(61) 

(62) 



Filed on N.A. 

Divisional to 




(71) 

(72) 






MUMBAI – 400 020, 



1. FERGUSON PAUL 

2. KUKULJ DAX 




(57) Abstract : A fabric care composition comprising a thermoplastic elastomer and a terpene. 





(19) 








(86) 


WET-SKIN TREATMENT COMPOSITION AND PROCESS FOR 

MOISTURIZING AND PROTECTING SKIN. 

17/05/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 






MUMBAI – 400 020, 



1. ARONSON MICHAEL PAUL 





(57) Abstract : The invention provides wet skin treatment compositions for use during bathing. The compositions are 

activated by water and retained efficiently on skin. The compositions impart desirable benefits to skin, are perceived to 

absorb quickly on wet skin, and leave the skin feeling clean, but non-greasy. The invention further relates to processes for 

making the compositions as well as methods of retaining moisture feel and of reducing dryness after treatment with said 

compositions. 





(19) 




(54) Title of the invention: A FABRIC TREATMENT COMPOSITION. 





(86) 

NIL 

NIL 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 






MUMBAI – 400 020, 



1. GOLDONI FRANCESCA 

2. KUKULJ DAX 




(57) Abstract : A fabric treatment composition comprising a textile compatible carrier and a supramolecular polymer, the 

supramolecular polymer comprising a building block comprising at least two moieties each moiety having at least 3 

groups capable of forming cross-linking hydrogen bonds with other building blocks to form the supramolecular polymer. 





(19) 




(51) International Classification: F 42 B (71) 




(86) 


SYSTEM FOR THE INITIATION OF ROUNDS OF INDIVIDUALLY 

DELAYED DETONATORS. 

06/06/2001 

U.S.A. 


No. and Filing Date : 06/06/2002 



(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : Disclosed is an electronic detonator delay 

assembly (24), having an associated detonator (12), that can be 

pre-programmed on site with a time delay and installed in a 

borehole to carryout a blast operation. The assembly is first 

coupled to a programming unit (50) to program the desired 

time delay, and then to a blasting unit (100), by means of a 

magnetic coupling device (24) in the electronic delay assembly 

and to a single pass of a conductive wire (22) through the 

magnetic coupling device. The programmed time delay in the 

electronic delay assembly can be double checked through a 

wireless communication link (6) between the electronic delay 

assembly and the programming unit. 


(72) 


SENEX EXPLOSIVES, INC. 


710 MILLERS RUN ROAD, 

CUDDY, PA 15031, 

U.S.A. 


EDDY CHRISTOPHER L. 

INGHAL RAJEEV N. 







(19) 




(51) International Classification: F 16 H 7/12 (71) 




(86) 


A BELT DRIVE SYSTEM AND A METHOD FOR ADJUSTING A 

VIBRATION IN A BELT DRIVE SYSTEM. 

11/02/2002 

U.S.A. 




Publication No. WO03/069188 A1 

(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : This invention comprises a method of using 

tensioners (10, 20) to tune a belt drive system. A tensioner 

(10) having a damping rate is used on an accessory belt slack 

side and a tensioner (20) having a damping rate is used on an 

accessory belt tight side. Outside a predetermined engine 

speed range, the tight side tensioner arm does not move 

because the dynamic tension in the span is less than the tight 

side tensioner friction damping. Within a predetermined 

engine speed range the tight side tensioner arm moves in order 

to damp a belt drive system vibration. 


(72) 








1. LIU KEMING 







(19) 

INDIA (21) Application No: 1068/MUMNP/2003 A 







(86) 


METHOD AND APPARATUS FOR CLARIFYING AND/OR 

THICKENING A SLURRY. 


FINLAND 

International Application : PCT/FI02/00538 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : The invention relates to a method of 

clarifying and/or thickening a solution containing 

solids i.e. a slurry, and the apparatus for accomplishing 

this. Using the method and apparatus of the present 

invention, the slurry to be fed into the clarification or 

thickening apparatus is distributed evenly into the 

slurry already in the tank. It is characteristic of the 

clarification tank now developed that the displacement 

capacity of the raking system in the tank is the same 

from the edges of the tank up to the centre. The 

displacement capacity is measured as being the 

(72) 


OUTOKUMPU OYJ 



FIN – 02200 ESPOO, 

FINLAND. 


1. NYMAN BROR 

2. NUORALA MATTI 





same as the underflow discharge capacity from the centre of the tank. The displacement capacity can be determined to be 

the same using rake displacement plates of different heights, according to the distance of the displacement plates from the 

rake shaft and the number of plates rotating on the same ring-like cross-section. 




(19) 

INDIA (21) Application No: 1069/MUMNP/2003 A 



(54) Title of the invention: OLEFIN ISOMERIZATION PROCESS. 





(86) 

23/05/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


ABB LUMMUS GLOBAL INC. 


1515 BROAD STREET, 

BLOOMFIELD, NJ 07003, 

U.S.A. 


1. GARTSIDE ROBERT J. 

2. GREENE MARVIN I. 

(57) Abstract : An olefin isomerization process employs a basic metal oxide catalyst, such as magnesium oxide. The 

catalyst is preferably a high purity magnesium oxide. The olefin isomerization process and catalyst described herein are 

advantageously used for the production of a terminal olefin such as 1-butene from an internal olefin such as 2-butene. 





(19) 




(51) International Classification: B 01 J 21/10 (71) 




(86) 


PROCESS FOR ACTIVATING OR REGENERATING A BASIC 

METAL OXIDE CATALYST USEFUL FOR OLEFIN 

ISOMERIZATION. 

23/05/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 






U.S.A. 


1. GARTSIDE ROBERT J. 

2. GREENE MARVIN I. 

(57) Abstract : A process is provided for treating a basic metal oxide olefin isomerization catalyst, such as magnesium 

oxide. The catalyst is activated by contact with a deoxygenated nitrogen containing not more than 5 ppm molecular 

oxygen by volume under activation conditions. The olefin isomerization process and catalyst described herein are 

advantageously used for the production of a terminal olefin such as 1-butene from an internal olefin such as 2-butene. 





(19) 



(54) Title of the invention: A MEMORY. 

(51) International Classification: G 11 C 15/04 (71) 




(86) 


U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A memory and method for accessing data in a 

memory which uses non redundant-form address decoders is 

disclosed. Lines in subarrays of the memory are selected using 

the redundant-form address. The least significant bit of the 

non redundant-form address is used to selected between these 

lines. The compare function of the cache memory is then done 

with a non redundant-form address. 



(72) 









1. ZHANG KEVIN 




(19) 




(51) International Classification: E 01 C 3/00 (71) 




(86) 


METHOD OF UPGRADING GRAVEL AND/OR DIRT ROADS AND A 

COMPOSITE ROAD RESULTING THEREFROM. 


U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A method of paving a gravel and/or dirt 

roadway (10) is provided. This method includes evaluating the 

roadway to determine if it is an appropriate candidate for 

emulsion stabilization, rotating a milling head (20) down a 

roadway to break up gravel and dirt base layer (14), injecting 

an asphalt emulsion into the broken up gravel and dirt (24), 

and mixing the emulsion with the gravel and dirt (24) so as to 

form an emulsion stabilized layer (18). The emulsion 

stabilized layer (18) is then spread and compacted to create a 

paved roadway. Following this, a wearing surface may be 

applied to the emulsion stabilized layer (18). 


(72) 


KMC ENTERPRISES, INC. 


4111 EAST 37 TH STREET NORTH, 

WICHITA, KS 67201-2256, 



1. GRUBBA BILL 

2. THOMAS TODD 

3. WEGMAN DAN 







(51) International Classification: H 04 L 29/06 (71) 




(86) 

A DATA UNIT BASED COMMUNICATION SYSTEM AND SAID 

COMMUNICATION SYSTEM. 

23/05/2001 

EP 

International Application : PCT/EP02/05624 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A method of processing a data unit of a first protocol layer (L3) for 

transmission in a data unit based communication system is described, comprising the 

steps of passing to a second protocol layer (L2) a given data unit of said first 

protocol layer (L3) that is to be transmitted, said second protocol layer (L2) lying 

below said first protocol layer (L3), determining a numeric value of a numerically 

quantifiable parameter associated with said given data unit of said first protocol layer 

(L3), embedding said given data unit of said first protocol layer (L3) into one or 

more data units of said second protocol layer (L2), performing transmission control 

for said one or more data units of said second protocol layer (L2) that embed said 

given data unit of said first protocol layer (L3), where said embedding and/or said 

transmission control is performed in accordance with said numeric value of said 

numerically quantifiable parameter. 


(72) 


TELEFONAKTIEBOLAGET LM 

ERICSSON [PUBL] 


S – 126 25 STOCKHOLM, 

SWEDEN. 


1. MEYER MICHAEL 

2. LUDWIG REINER 

3. SACHS JOACHIM 

4. SAGFORS MATS 







(19) 




(54) Title of the invention: A TEST KIT FOR VISUALIZING FINE LINES AND WRINKLES. 

(51) International Classification: A 61 B 5/103 (71) 




(86) 

30/05/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 

(57) Abstract : A test kit and method for visualizing fine lines and 

wrinkles is provided, the kit including a transparent strip (2) with an 

adhesive on one surface thereof and an imaging substrate with at least one 

darkened glossy area for receiving the transparent strip. Written 

instructions are provided in the kit. These advise a consumer to place the 

adhesive surface of the strip against a skin area requiring measurement. 

Thereafter the strip is removed and placed against the darkened area of the 

substrate. Topographical features of the skin can be viewed through the 

transparent strip with the transferred skin image onto the blackened 

background. A cosmetic anti-aging product can be applied to the skin over 

a period of time. Beneficial changes caused by the product are visualized 

through the test strip as periodic measurements are taken. 







MUMBAI – 400 020, 



4. TELESCA JOSEPHINE 

5. MURRAY LIAM ANTHONY PETER 









(19) 



(54) Title of the invention: IMPROVED STENT. 

(51) International Classification: A 61 F 2/06 (71) 

(31) Priority Document No. : 10/063,179 



(86) 

28/03/2002 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A stent comprises a plurality of 

circumferential bands. Circumferential bands which 

are adjacent one another are connected one to the 

other. The circumferential bands include peaks and 

troughs interconnected by bent struts. The bands 

may overlap or may be connected by connectors. 



(72) 


BOSTON SCIENTIFIC LIMITED. 


THE CORPORATE CENTRE, 

BUSH HILL, BAY STREET, 

ST. MICHAEL, BARBADOS, 

WEST INDIES. 


1. GREGORICH DANIEL 

2. GIRTON TIMOTHY 






Publication After 18 months 

The following Patent application have been published under Section 11A of the Patents 

(Amendment) Act, 2005 

(21) Application No.: 1165/MUMNP/2003 A 

(PCT/US02/18836) 


Application: 

23/12/2003 

(54) Title of the invention: TEMPERATURE CONTROLLED IN SITY WAX PURIFICATION 

(51) International classification: C10G 

(30) Priority Data: 

(31) Document No.: 09/905,231 

(32) Date: 13/07/2001 

(33) Name of convention country: USA 

(66) Filed U/s. 5(2): NO 

(61) Patent of addition to application No.: NIL 

(62) Filed on: N.A. 

(63) Divisional to Application No.: NIL 


(57) Abstract: A hydrocarbon wax product from a HCS 

slurry comprising liquid synthesis product and catalyst 

particles is purified by circulating the slurry from a 

synthesis zone with a first temperature through a treatment 

zone with a second temperature in which a hydrogencontaining 

treatment gas contacts the slurry. The gas 

treatment removes impurities from the hydrocarbon wax 

product and also removes catalyst de-activating species 

which may be present in the slurry. Purified wax product is 

separated and removed from the treated slurry via wax 

withdrawal means. This avoids or minimizes the need for 

further treating the wax product. Remaining treated slurry 

may be returned to the synthesis zone. 

Figure: 1. 

(71) Name of the Applicant: 

EXXONMOBIL RESEARCH AND 

ENGINEERING COMPANY 


1545 ROUTE 22 EAST, P.O. BOX 900, 

ANNANDALE, NEW JERSEY 08801- 

0900, USA. 

(72) Name of the Inventors: 

1. WITTENBRINK ROBERT 

JAY 

2. BURNS, LOUIS, FRANCIS, 

3. HOWSMON, GREGG, 

JOHNSTON, 

4. SAY, GEOFFREY, RHYS, 

5. MAULDIN, CHARLES, 

HARRISON. 






(PCT/US02/21082) 


Application: 


(54) Title of the invention: METHOD OF ABLATING AN OPENING INA HARD, NON- 

METALLIC SUBSTRATE 

(51) International classification: B23K 15/08 


(31) Document No.: 60/302,495 

(32) Date: 02/07/2001 


(66) Filed U/s. 5(2): NO 






VIRTEK LASER SYSTEMS, INC. 


785 BRIDGE STREET, WATERLOO, 

ONTARIO, N2V 2K1, CANADA. 


1. GLOVER, RUIZ, 

2. CUMMINGS, MIKE, 

3. ARCHIBALD, CEC. 

(57) Abstract: A method of ablating a hole into a hard, non-metallic substrate (24) is disclosed. At least on laser 

assembly (12) capable of generating a laser beam (16a) in an axis having a focus that is moveable relative to the axis is 

provided. A focus of the laser beam (16a) is positioned adjacent at least one surface of the substrate (24). A first layer 

(Pass-1) of the substrate (24) is ablated by the laser beam (16a). The focus is moved relative to the axis corresponding 

to the depth of the substrate (24) thereby enabling ablation of successive layers (Pass 2-10) of the substrate (24) are 

ablated to generate a hole (32) into the substrate (24). 

Figure: 2B. 



(19) INDIA (21) 




(54) Title of the invention: PROCESS FOR PREPARING SUBSTITUTED POLYSACCHARIDE 



(32) Priority Date : 20/07/2001 



No. 

: PCT/EP02/07683 



No. 

: WO 03/010206 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 





165-166, BACKBAY RECLAMATION, 

MUMBAI – 400 020, 



1. ROGERS SUSANNE HENNING 

2. ROYLES BRODYCK JAMES 

LACHLAN 

3. WHITE MICHAEL STEPHAN 




The invention relates to polysaccharide graft polymers useful for incorporation as benefit agents in laundry 

detergent and fabric treatment compositions, and their preparation. The invention also relates to substituted 

polysaccharides useful as macroinitiator intermediates for the preparation of the polysaccharide graft polymers, 

and the preparation of the macroinitiators. The polysaccharide graft polymers may be used, for example, to 

impart soil release and/or fabric care benefits to laundry detergent or fabric treatment compositions. 

(FIG.: NIL) 




(19) INDIA (21) 




(54) Title of the invention: INSECTICIDAL MIXTURE CONTAINING GAMMA-CYHALOTHRIN 

(51) International Classification : A 01 N 53/00 (71) 


(32) Priority Date : 25/07/2001 



No. 

: PCT/GB02/03181 



No. 

: WO 03/011031 A1 (72) 



: NIL 


(62) 



No. 

: NIL 



SYNGENTA LIMITED 


EUROPEAN REGIONAL CENTRE, 

PRIESTLEY ROAD, SURREY 

RESEARCH PARK, GUILDFORD, 

SURREY GU2 7YH, ENGLAND. 


1. MARTIN STEPHEN CLOUGH 




An insecticidal mixture of gamma-cyhalothrin [(S)-α-cyano-3-phenoxybenzyl (Z)-(1R,3R)-3-(2-chloro-3,3,3tziflu-oro-l-propenyl)-2,2-dimethylcyclopropanecarboxylate] 

and one or more further active ingredients; 

compositions containing them and their use. 

(FIG.: NIL) 




(19) INDIA (21) 





ORTHO-SUBSTITUTED ARYL AMIDES FOR CONTROLLING 

INVERTERBRATE PESTS 



(32) Priority Date : 15/08/2001 



No. 

: PCT/US02/26959 



No. 

: WO 03/016300 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 


E.I.DU PONT DE NEMOURS AND 

COMPANY 


1007 MARKET STREET, 

WILMINGTON, DELAWARE 19898, 



1. BRUCE LAWRENCE 

FINKELSTEIN 

2. GEORGE PHILIP LAHM 

3. THOMAS PAUL SELBY 

4. THOMAS MARTIN STEVENSON 




Disclosed are compounds of Formula I, their N-oxides and agriculturally suitable salts (I) wherein J is a phenyl 

ring, a 5- or 6-membered heteroaromatic ring or an aromatic 8-,9- or 10-membered fused carbobicyclic or 

heterobicyclic ring system wherein each ring or ring system is substituted with from one to four substituents 

independently selected from R 5 ; and A, B, G, R 1 , R 2 , R 3 , R 4 , R 5 , R 6 and n are as defined in the disclosure. Also 

disclosed are methods for controlling invertebrate pests comprising contacting the pests or their environment with 

a biologically effective amount of a compound of Formula (I) and compositions containing the compounds of 

Formula (I). 

(FIG.: NIL) 




(19) INDIA (21) 


(54) Title of the invention: A BELT 

(51) International Classification : F 16 G 5/20, 9/00, 1/00 (71) 


(32) Priority Date : 18/07/2001 



No. 

: PCT/US02/23097 



No. 

: WO 03/008840 A3 (72) 



: NIL 


(62) 


No. 

: NIL 



The invention comprises a belt having a plied 

construction overlying tensile cords. An elastomeric 

layer overlies an overcord which overlies yet another 

elastomeric layer which in turn overlies a tensile 

cord. The overcord layer supports the tensile cords 

during molding thereby stabilizing a cordline 

centerline position with respect to a rib apex. This 

construction significantly reduces a distance from a 

tensile cord centerline to a rib apex and rib/pulley 

interface in a multi-ribbed belt, thereby significantly 

increasing belt life. 

(FIG.: 2) 











1. CRAIG KOPANG 






(19) INDIA (21) 





AN ORGANO-PHOSPHOROUS COMPOUNDS FOR ACTIVATING 

GAMMA/DELTA T CELLS 


(31) Priority Document No. : 1) 101 34 705.7 

2) 101 35 395.2 

(32) Priority Date : 1) 20/07/2001 

2) 25/07/2001 


(86) 


No. 

: PCT/EP02/07986 



No. 

: WO 03/009855 A2 



: NIL 


(62) 


(FIG.: NIL) 



No. 

: NIL 


(72) 


BIOAGENCY AG 


SCHNACKENBURGALLEE 116A, 

22525 HAMBURG, GERMANY. 


1. JOMAA HASSAN 

2. WOLF OLIVER 

3. ALTINCICEK BORAN 

4. EBERL MATHIAS 

5. HINTZ MARTIN 

6. KOLLAS ANN-KRISTIN 

7. REICHENBERG ARMIN 

8. WIESNER JOCHEN 




The invention relates to phosphororganic compounds of 

general formula (I), to the production thereof, and to their use 

for activating gamma/delta T cells, for screening inhibitors of 

the GcpE and of the LytB enzyme as well as for the 

prophylaxis and treatment of diseases in humans and animals. 



(19) INDIA (21) 





A COMPOSITION FOR COSMETIC TREATMENT OF HAIR AND/OR 

SCALP 

(51) International Classification : A 61 K 7/06 (71) 


(32) Priority Date : 18/07/2001 



No. 

: PCT/EP02/07904 



No. 

: WO 03/007901 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI – 400 020, 



1. BAILEY PETER LAWRENCE 

2. LITTLE CHRISTOPHER JOHN 

3. MCGLONE FRANCIS 

4. RUKWIED ROMAN 

5. WATKINSON ALLAN 




Hair and/or scalp treatment compositions comprise an antidandruff agent, an effective amount of a cannabinoid 

receptor (CBR) activating agent and a cosmetically acceptable diluent or carrier. Alternatively, the compositions 

may be shampoo compositions comprising from 3 to 50wt% surfactant, a CB receptor activating agent and a 

cosmetically acceptable diluent or carrier, provided that the CB receptor activating agent is not 

palmitoylethanolamide. The compositions are useful in the treatment and/or prevention of the symptoms of 

dandruff and can reduce scalp itch, a symptom which is typically associated with dandruff. 

(FIG.: NIL) 




(19) INDIA (21) 





A LAUNDRY CLEANING COMPOSITION COMPRISING GRAFT 

POLYMER BENEFIT AGENT 


(31) Priority Document No. : 1) 60/306,738 

2) 0119258.2 

(32) Priority Date : 1) 20/07/2001 

2) 07/08/2001 

(33) Name of priority country : 1) USA 

2) U.K. 

(86) 


No. 

: PCT/EP02/07685 



No. 

: WO 03/010268 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 






MUMBAI – 400 020, 



1. CHARMOT DOMINIQUE 

2. JAYARAMAN MANIKANDAN 

3. CHANG HAN TING 

4. MANSKY PAUL 

5. BLOKZIJL WILFRIED 

6. JONES CHRISTOPHER 

CLARKSON 




Laundry treatment products comprise a graft polymer benefit agent and at least one additional laundry cleaning 

ingredient. The graft polymer benefit agent preferably provides soil release or fabric care benefits. The graft 

polymer benefit agent comprises a polysaccharide backbone and a plurality of graft chains extending from the 

backbone, each graft chain having a degree of polymerization between 5 and 250. The graft polymer is 

substantially free of cross-linking and has a degree of substitution of grafts across a bulk sample in the range of 

from 0.02 to 1.0. The graft polysaccharide copolymers may be prepared using living-type free radical 

polymerization techniques which provide control over the degree of substitution, the graft/co-block composition 

and structure. 

(FIG.: NIL) 




(19) INDIA (21) 


(54) Title of the invention: A LAUNDRY CLEANING COMPOSITION 



(32) Priority Date : 20/07/2001 



No. 

: PCT/EP02/07682 



No. 

: WO 03/010267 A1 



: NIL 


(62) 



No. 

: NIL 




(72) 






MUMBAI – 400 020, 



1. BLOKZIJL WILFRIED 

2. JONES CHRISTOPHER 

CLARKSON 

3. ROGERS SUSANNE HENNING 

4. ROYLES BRODYCK JAMES 

LACHLAN 

5. WHITE MICHAEL STEPHEN 




A laundry cleaning composition comprises a graft polysaccharide polymer benefit agent capable of imparting a 

benefit such as soil release or fabric care, and at least one additional laundry cleaning ingredient. 

(FIG.: NIL) 




(19) INDIA (21) 





A SYSTEM FOR SECURE, AUTOMATED RESPONSE TO DISTRIBUTED 

DENIAL OF SERVICE ATTACKS. 

(51) International Classification : H 04 L 29/06 (71) 


(32) Priority Date : 03/07/2001 



No. 

: PCT/US02/20759 

Filing Date : 27/06/2002 


No. 

: WO 03/005666 A3 



: NIL 


(62) 



No. 

: NIL 


An apparatus and method for secure, automated response 

to distributed denial of service (DDoS) attacks are 

described. The method includes notification of a DDoS 

attack received by an Internet host. Once received by an 

Internet host, the Internet host establishes security 

authentication from an upstream router from which the 

attack traffic, transmitted by one or more host 

computers, is received. The Internet host then transmits 

filter(s) to the upstream router generated based upon 

characteristics of the attack traffic. Once installed by the 

upstream router, the attack traffic is dropped to terminate 

a DDoS attack. In addition, the router may determine 

upstream router(s) coupled to ports from which attack 

traffic is received, and securely forward the filter(s) to 

the upstream routers as a routing protocol updated in 

order to drop the attack traffic at a point closer to a 

source of the DDoS attack. 

(72) 

(FIG.: 4) 





2200 MISSION COLLEGE, 





1. DAVID PUTZOLU 

2. TODD ANDERSON 






(19) INDIA (21) 





REDUCED STATE TRANSITION DELAY AND SIGNALING OVERHEAD 

FOR MOBILE STATION STATE TRANSITIONS 

(51) International Classification : H 04 Q 7/00 (71) 

(31) Priority Document No. : 1) 60/313,451 

2) 60/330,403 

3) 60/337,030 

4) 60/360,373 

5) 10/210,634 

(32) Priority Date : 1) 20/08/2001 

2) 18/10/2001 

3) 07/11/2001 

4) 28/02/2002 

5) 31/07/2002 


(86) International Application : PCT/IB02/03334 

No. 


(87) International Publication : WO 03/017688 A2 

No. 

(61) Patent of addition to : NIL 



(62) Divisional to Application : NIL 

No. 



A wireless communication network reduces its signaling overhead by 

recognizing when a mobile station transitions from an inactive state, 

such as Control Hold or quasiactive, back to an active state. Based on 

such recognition by the network, the mobile station begins sending 

desired traffic data without need for explicity negotiating its return to 

active state, thereby reducing or eliminating higher-layer signaling, 

e.g., Layer 3 and above, that is otherwise required for return to active 

state operations. The network might further avoid explicit signaling 

by, for example, using transmitted reverse link Power Control Bits to 

indicate that an inactive mobile station should remain inactive. In this 

manner, inactive mobile stations may be allowed to return to active 

state without explicit signaling where appropriate, or held in the 

inactive state if needed, all without need for explicit network 

signaling. 

(FIG.: 2) 


(72) 


TELEFONAKTIEBOLAGET LM 

ERICSSON (PUBL) 


TELEFONPLANM S-126 25 

STOCKHOLM, SWEDEN. 


1. FARIDEH KHALEGHI 

2. ANTHONY SOONG 

3. JONAS WIOREK 

4. PATRIK LUNDQVIST 

5. SHAWN SHIAU-HE TSAI 

6. YOUNG YOON 






(19) INDIA (21) 




(54) Title of the invention: AN INK RECORDABLE SUBSTRATE COATING COMPOSITION 

(51) International Classification : B 41 M 5/00 

C 09 D 175/04 

(31) Priority Document No. : 1) 60/309,348 

2) 10/205,033 

(32) Priority Date : 1) 01/08/2001 

2) 26/07/2002 


(86) 


No. 

: PCT/US02/24257 



No. 

: WO 03/011608 A1 



: NIL 


(62) 



No. 

: NIL 


(71) 

(72) 


PPG INDUSTRIES OHIO INC. 


3800 WEST 143RD STREET, 

CLEVELAND, OH 44111, USA. 


1. BENENATI PAUL L. 

2. KHALE CHARLES F. 

3. HILL CHARLES T. 

4. LIPKO LARRY E. 

5. KOVACS JOSEPH P. 

6. PARRINELLO LUCIANO M. 




A water resistant coating composition for ink jet recordable substrates having a pH of less than 7, which includes: 

(a) an aqueous polyurethane dispersion; and (b) and aqueous solution of a nitrogen containing polymeric dye 

fixative compound. When applied to a suitable substrate, the coating composition allows for the recording of 

sharp, waterfast images. A coated ink recordable substrate is also disclosed, which includes a substrate having at 

least one side and at least one side of the substrate has a coating layer derived from the above described coating 

composition. 

(FIG.: NIL) 




(19) INDIA (21) 




(54) Title of the invention: CONTROLLED RELEASE FORMULATION OF LAMOTRIGINE 



(32) Priority Date : 07/06/2002 



No. 

: PCT/IN03/00213 

Filing Date : 06/06/2003 


No. 

: WO 03/104192 A2 



: NIL 


(62) 



No. 

: NIL 


(72) 


TORRENT PHARMACEUTICALS 

LIMITED 


TORRENT HOUSE, 

OFF ASHRAM ROAD, 

DINESH HALL, 

AHMEDABAD – 380 009, 



1. NADKARNI SUNIL SADANAND 




Rapidly disintegrating multiparticulate controlled release formulations of lamotrigine having an improved 

pharmacokinetic profile and improved patient compliance, and process of preparing the formulations. It provides 

better control of blood plasma levels than conventional tablet formulations that is administered once or more 

times a day. 

(FIG.: NIL) 




(19) INDIA (21) 


(54) Title of the invention: AN ELECTRIC HEATING FUMIGATOR 

(51) International Classification : A 01 M 13/00 (71) 


(32) Priority Date : 23/07/2001 

(33) Name of priority country : CHINA 


No. 

: PCT/CN02/00510 



No. 

: WO 03/015510 A1 



: NIL 


(62) 



No. 

: NIL 


The present invention is related to an electric heating fumigator 

(100) which comprises a base (9), a case cover (12) and a heater 

support (3) mounted on the base (9). A heater (1) is inserted into 

the heater support (3) and heat-insulation layers (2,5) are 

attached to the heater support (3) so that one of them is located 

between the heater (1) and the heater support (3). The bottom of 

the support (3) is fixed on the base (9) of the fumigator. The 

present invention provides an electric heating fumigator which 

brings such better heat-insulation and electrical insulation effects 

that it can increase to a higher temperature to heat and discharge 

a large amount of medicament in a short time in a save and 

stable way. 

(FIG.: 2) 




(72) 


BEIJING TAIMING SCIENCE & 

INFORMATION TECHNOLOGY CO. 

LTD. 


ROOM 302, BUILDING B, NO. 11, 

DESHENGMENWAI STREET, 

XICHENG DISTRICT, 

BEIJING 100088, CHINA. 


1. JINING ZHANG 

2. ZHE ZHANG 






(19) INDIA (21) 




(54) Title of the invention: IONISING BEAM INSPECTION DEVICE AND PROCESS 

(51) International Classification : A 61 N 

G 21 G 5/00 

(31) Priority Document No. : 02/06778 

(32) Priority Date : 03/06/2002 

(33) Name of priority country : FRANCE 


No. 

: PCT/FR03/01639 



No. 

: WO 03/101528 A2 



: NIL 


(62) 


No. 

: NIL 



The invention relates to a beam inspection device, 

consisting of: an inspection head (110) comprising 

a scintillator (114) and at least one diffuser unit 

(116, 117) which is associated with said scintillator, 

and a first means (118) of forming at least one 

image of at least one part of the inspection head 

comprising the scintillator. According to the 

invention, the scintillator comprises at least one 

essentially-uniform, solid sheet of scintillation 

material with two main opposing faces. The 

invention is suitable for use in radiotherapy. 

(FIG.: 1) 


(71) 

(72) 


CENTRE NATIONAL DE LA 

RECHERCHE SCIENTIFIQUE 


3, RUE MICHEL-ANGE, 

F-75794 PARIS, 

CEDEX 16, FRANCE. 


1. JEAN-MARC FONTBONNE 






(19) INDIA (21) 


Application No: 00061/MUMNP/2004 A 


(54) Title of the invention: FABRIC CONDITIONING COMPOSITIONS 

(51) International Classification : C11D3/00; C11D17/00 (71) 


(32) Priority Date : 27/07/2001 



No. 




No. 

: WO 03/012019 A1 



: NIL 


(62) 



No. 

: NIL 


(72) 





165-166 BACKBAY RECLAMATION, 

MUMBAI – 400 020, 



1. ELLSON KAREN JANE 

2. HUBBARD JOHN FRANCIS 




An aqueous, liquid fabric conditioning composition and a method for making such a composition are provided 

where the composition comprises a quaternary ammonium cationic softening compound and a non-ionic 

surfactant, where the composition comprises an emulsion in which 80% or more by weight of the droplets in the 

emulsion have a mean diameter of from 0.4 to 60 microns, as measured using a Malvern particle size analyser 

with a 45mm lens for D[0,1] measurements and both a 45mm and a 1000mm lens for D[0,9] measurements. Use 

of a nonionic surfactant to improve the dispersibility in water of an aqueous, liquid fabric conditioning 

composition is also provided. 

(FIG.: NIL) 




(19) INDIA (21) 





A METHOD OF PREPARATION OF A VACCINE FOR TREATING OR 

PREVENTING A DISEASE OR DISORDER CAUSED BY MYCOPLASMA 

BOVIS 



(32) Priority Date : 02/07/2001 



No. 

: PCT/IB02/01937 



No. 

: WO 03/004051 A2 (72) 



: NIL 


(62) 


No. 

: NIL 



The present invention relates for treating or 

preventing a disease or disorder in an animal caused 

by infection by Mycoplasma bovis (M. bovis) by 

administering to the animal an effective amount of a 

Mycoplasma hyopneumoniae (M. hyo) vaccine. The 

M. hyo vaccine can be a whole or partial cell 

inactivated or modified live preparation, a subunit 

vaccine, or a nucleic acid or DNA vaccine. The M. 

hyo vaccine administered in accordance with the 

present invention can be synthesized or 

recombinantly produced. 

(FIG.: 1) 









1. ALEXANDER CROSSAN 

GOUDIE 

2. ANDREW RAYMOND PETERS 

3. ROBIN LEE KEICH 






(19) INDIA (21) 




(54) Title of the invention: A METHOD OF LAUNDERING ARTICLES IN A WASH LIQUOR 

(51) International Classification : C 11 D 3/42, 3/39 (71) 


(32) Priority Date : 02/08/2001 



No. 

: PCT/EP02/08535 



No. 

: WO 03/014283 A1 (72) 



: NIL 


(62) 



No. 

: NIL 






165-166 BACKBAY RECLAMATION, 

MUMBAI – 400 020, 



1. DIXON SARAH 

2. GRATTON PETER LESLIE 

3. OAKES JOHN 




A detergent composition which comprises: a surfactant, a builder, a fluorescer; one or more of a bleach precursor 

which is preferably N,N,N’N’-tetra-acetyl ethylene diamine or sodium nonanoyloxy benzene sulphonate, one or 

more of a hydrogen peroxide source which is preferably an alkali metal perborate or percarbonate. Optionally it 

comprises a nitrogen-containing dye binding polymer selected from polymers and co-polymers of vinylpyrrolidone, 

vinyl-pyridine N-oxide, and vinyl-imidazole, and mixtures thereof. The composition is essentially 

free of copper binding species, other than those which are deactivated by calcium salts. 

(FIG.: NIL) 




(19) INDIA (21) 




(54) Title of the invention: RETRACTING NEEDLE SAFETY ASSEMBLY 

(51) International Classification : A 61 M 5/32 (71) 

(31) Priority Document No. : 60/311,006 

(32) Priority Date : 09/08/2001 



No. 

: PCT/US02/25245 



No. 

: WO 03/015855 A1 (72) 



: NIL 


(62) 



No. 

: NIL 



BECTON DICKINSON AND 

COMPANY 


1 BECTON DRIVE, FRANKLIN 

LAKES, NJ 07417, USA. 


1. SAULENAS WILLIAM 

2. SULLIVAN MICHELLE 

3. WILKINSON BRADLEY 

4. SWENSON KIRK D. 




A retractable safety needle assembly comprising: a tabular outer body including a first end, a second end and a 

tabular wall extending along an axis from said first end to said second end to define an interior opening within 

said outer body, said outer body including a guide channel offset from said axis; a retraction assembly positioned 

within said interior opening of said outer body, said retraction assembly including a cannula having an 

intravenous puncture tip and a non-patient puncture tip and including a fin for corresponding engagement with 

said guide channel of said outer body, said retraction assembly adapted for movement within said interior 

opening of said outer body from a first position in which said intravenous puncture tip extends from said first end 

of said outer body to a second position in which said intravenous puncture tip and said non-patient puncture tip 

are contained entirely within said outer body and said cannula is offset from said axis of said outer body; a 

retaining element for preventing movement of said retraction assembly between said first position and said 

second position; and a biasing element for applying a retraction force between said retraction assembly and said 

outer body to move said retraction assembly from said first position to said second position upon release of sad 

means for preventing movement 

(FIG.: NIL) 




(19) 




(51) International Classification: E 02 F 9/28 (71) 




(86) 


EXCAVATING EQUIPMENT WEAR MEMBER AND SUPPORT 

MEMBER AND EXCAVATING EQUIPMENT HAVING SAID WEAR 

MEMBER AND SUPPORT MEMBER. 

16/08/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : An elongated excavation tooth assembly 

(12,14,16)includes a replaceable tooth point (12)and an adapter 

structure comprising (1) an intermediate adapter (14)having a 

front end nose (48)complementarily received in a rear end 

pocket (72)of the point and captively retained therein by a first 

connector pin structure (18), and (2) a main adapter (16)having 

a front end nose (98)complementary received in a rear end 

pocket (34)of the intermediate adapter (14)and captively 

retained therein by a second connector pin structure(20) and a 

rear end operatively securable to an excavating bucket lip (24). 

Special configurations of the point (12)and adapter portions 

(14,16)of the assembly, including horizontally elongated oval 

configurations of the noses (48,98), horizontal orientation of 

the connector pins (18,20), nose stabilization protrusions 

(34,114) at the nose retainer openings (66,84,116,46), and 

complementarily scalloped adapter and point interface areas, 

provide the assembly with reduced size and improved strength, 

wear and operational characteristics. 


(72) 


HENSLEY INDUSTRIES, INC. 


2108 JOE FIELD ROAD, 

P. O. BOX 29779, DALLAS, 

TEXAS 75229, 



1. SHAMBLIN WAYNE A. 

2. RUVANG JOHN A. 

3. ROBINSON HOWARD W. 




( Figure: 3, 4 & 6 ) 



(19) 




(54) Title of the invention: PREPARATION OF ANHYDROUS CETP INHIBITOR. 





(86) 

28/09/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 




EASTERN POINT ROAD, GROTON, 

CONNECTICUT 06340, 



1. ROSE PETER ROBERT 

2. LAMBERT JOHN FRANCIS 

3. ORRILL SUSAN LEE 




(57) Abstract : This invention relates to methods for preparing anhydrous CETP inhibitor, (2R,4S)-4-[3,5-bistrifluoromethyl-benzyl)-methoxycarbonyl-amino]-2-ethyl-6-trifluoromethyl-3,4-dihydro-2H-quinoline-1-carboxylic 

acid ethyl ester by crystallization. 





(19) 




(54) Title of the invention: DRAFT TUBE AND AIR BUBBLE TOWER. 

(51) International Classification: F 28 D 1/047 (71) 




(86) 


JAPAN 

International Application : PCT/JP02/08784 



Publication No. WO03/023306 A1 

(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


KYOWA HAKKO KOGYO CO., LTD. 


6-1, 1-CHOME, CHIYODA-KU, 

TOKYO 100-8185, 

JAPAN. 


1. TANAKA HISAO 

2. HIDAKA HIROMICHI 

3. AZAKAMI NORIYUKI 

4. TAKAHASHI YUICHI 

5. FUKUDA HIDEKI 




(57) Abstract : A draft tube installed in a tower for storing solution of an air bubble 

tower and formed of a hollow tube, wherein a space is provided on the entire side 

peripheral surface thereof. 





(19) 




(54) Title of the invention: A CYLINDER HEAD FOR AN INTERNAL COMBUSTION ENGINE. 

(51) International Classification: F 02 B 31/00 (71) 

(31) Priority Document No. : GM 609/2001 



(86) 

02/08/2001 

AUSTRIA 

International Application : PCT/AT02/00232 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : The invention relates to a cylinder head (1) 

for an internal combustion engine with at least one inlet 

channel (3), which generates a swirling flow (S) in the 

combustion chamber (2), preferably curved in the direction of 

the swirling flow (S) with an external wall region (3a) and an 

internal wall region (3b) relative to the swirling flow (S). A 

valve seat ring (4) is arranged in the region of the opening (9) 

of the inlet channel (3) into the combustion chamber (2). 

According to the invention, a strong swirling flow (S) without 

significant reduction of the flow cross-section of the inlet 

channel (3) may be achieved whilst keeping the mechanical 

loading on the cylinder head to a minimum, whereby the 

external wall region (3a), in the region of the valve seat ring 

(4), is at least partly formed by a projection (11) of the 

cylinder head (1) within an internal surface (4a) of the valve 

seat ring (4), whereby the internal surface (4a) of the valve 

seat ring (4) extends beyond said projection (11). 


(72) 


AVL LIST GMBH 


HANS-LIST-PLATZ 1, 

A-8020 GRAZ, AUSTRIA. 


LAIMBOCK FRANZ 





(19) 




(51) International Classification: H 02 M 7/00 (71) 




(86) 


ELECTRICAL POWER CONSERVATION APPARATUS AND 

METHOD. 

10/08/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


MICROPULSE TECHNOLOGIES, 

INC. 


4565 RUFFNER STREET, 

SAN DIEGO, CA 92111, 



1. AMARILLAS SAL G. 

2. ASBURY JIMMIE 

(57) Abstract : An electrical power control apparatus and 

method for a conventional 60 hertz or other conventional 

frequency electrical AC power supply voltage waveform to 

prove an effective output current and voltage to an intended load 

whereby the output frequency is the same as the input 

frequency. Using a switching means (16) capable of micro 

switching the current on and off, and a plurality of substantially 

equal length and duration interruptions of current on both sides 

of an AC current oscillation, the output effective voltage and 

resulting current may be preset and controlled to a preprogrammed 

output level regardless of input voltage having one 

or more phases. Or, the output voltage and resulting current may 

be continually monitored with the load (22) integrated into the 

circuit being monitored and continually adjusted to yield 


maximum power use 

savings while avoiding damage to the components attached to the circuit. Additional embodiments provide for use of the 

micro chopping device as a circuit breaker (32) for over current protection and as a smart circuit breaker to yield a data 

stream on individual circuit power usage which can be communicated to a monitoring station locally or by electronic 

transmission of information to a remote monitoring station. Real time monitoring and adjustment of power usage may be 

accomplished using such communication and two way communication between the device and communicating 

monitoring station also allow for real time charges for power usage and deduction from prepaid account for real time 

power usage. 




(19) 




(51) International Classification: A 61 F 2/14 (71) 




(86) 


INTRA SCLERA IMPLANT FOR TREATMENT OF GLAUCOMA 

AND PRESBYOPIA. 

03/08/2001 

U.S.A. 

International Application : PCT/US02/24646 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


GLAUCOMA RESEARCH 

TECHNOLOGIES, INC. 


3111 CAMINO DEL RIO NORTH SAN 

DIEGO, CA 92108, 

A CALIFORNIA CORPORATION, 



CASTILLEJOS DAVID 




(57) Abstract : An intra scleral implant (10) and method of implantation for use in the treatment of intraocular pressure 

and presbyopia. The implant features a body portion (46) and protrusions (48) from the body portion to anchor the device 

in a cavity (19) formed in the scleral wall (16) of the eye(12). Optionally a drug delivery function is provided to allow 

long term communication of drugs to tissue surrounding the implant. 





(19) 




(51) International Classification: H 01 J 01/62 (71) 




(86) 


ELECTROLUMINESCENT FLEXIBLE FILM FOR PRODUCT 

PACKAGING. 

11/09/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A flexible electroluminescent film 10, and 

packaging material and packages made therefrom, that 

incorporates electroluminescent material within the polymer 

packaging film layers to enable the film to be illuminated 

without an external light source. The film may also 

comprise various thin-film items, such as power source 12, 

inverter 13, switch 14, integrated circuit 91, radio receiver, 

and speaker, all within the film layers. The film can be used 

in existing form and fill packaging machines without 

substantial modifications to the machines. 


(72) 


FRITO-LAY NORTH AMERICA, INC. 


7701 LEGACY DRIVE, 

PLANO, TEXAS 75024-4099, 



1. KNOERZER ANTHONY ROBERT 

2. KOHL GARRETT WILLIAM 

3. PAPALIA ROCCO DOMINIC 







(19) 




(51) International Classification: G 06 F 1/00 (71) 


2. 60/414,964 



(86) 


TECHNIQUES FOR PERFORMING LOGIC OPERATIONS USING 

QUANTUM STATES OF SINGLE PHOTONS. 

1. 06/11/2001 

2. 30/09/2002 

U.S.A. 

International Application : PCT/US02/35248 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A method and apparatus for performing logic 

operations using quantum polarization states of single 

photons, include a first polarizing beam splitter having first 

input spatial modes and first output spatial modes for a first 

set of orthogonal polarizations. A second polarizing beam 

splitter has a second input spatial mode and second output 

spatial modes for a second set of orthogonal polarizations. 

The second set of orthogonal polarizations is different from 

the first set. The second input spatial mode is aligned with a 

first detected output spatial mode. A single photon detector of 

multiple single photon detectors is disposed along each one of 

the second output spatial modes. A first device output carries 

an output photon based in part on a number of photons 

detected by the single photon detectors. Such logic operations 

may be used in quantum computers for quantum information 

processing. 


(72) 


THE JOHNS HOPKINS UNIVERSITY 


34 TH AND CHARLES STREETS, 

BALTIMORE, MARYLAND 21218, 



1. PITTMAN TODD B. 

2. FRANSON JAMES D. 

3. JACOBS BRYAN C. 







(19) 




(54) Title of the invention: A COMPOUND HOLOW CONTAINER. 

(51) International Classification: B 05 C 1/00 (71) 




(86) 

30/08/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


NP2 LLC 

(57) Abstract : Described is a compound hollow container (900) having a 

multiplicity of compartments (16, 17), e.g., two or three compartments, with the 

container (900) being capable of containing, storing and dispensing one or more 

liquids such as nail polish and nail polish remover, and nail polish curing agent, 

and optionally, fluidized solids such as nail glitter and, further optionally, 

accessories therefor such as nail polish remover cleaning pads (88). The container 

(900) is equipped with liquid applicators (52), e.g., vertically disposed long 

brushes (53), or porous pads for each of the liquids and, optionally, a fluidized 

solid (300) dispenser for the fluidized solids, e.g., a screen (200) or multiplicity of 

orifices (201A)which can be opened and closed, located in the upper lid portion 

(10)of the container (900). 



FREDERIK CAPUTO 903, 

EAST 92 STREET, 

BROOKLYN, NY 11236, 



1. CANTONE THOMAS J. 

2. CAPUTO FREDERICK 




( Figure: 5B ) 



(19) 





(31) Priority Document No. : 1. 011 21201.6 

2. 60/318,354 



(86) 


PLASTER FOR THE TREATMENT OF DYSFUNCTIONS AND 

DISORDERS OF NAILS. 

1. 04/09/2001 

2. 12/09/2001 

1. E.P.O. 

2. U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


TROMMSDORFF GMBH & CO. KG 

ARZNEIMITTEL 


TROMMSDORFFSTRASSE 2-6, 

52475 ALSDORF, GERMANY. 


SUSILO RUDY 




(57) Abstract : The present invention relates to plasters for prophylaxis and/or treatment of dysfunctions or disorders 

of nails, especially onychomycosis, onychocryptosis, nail psoriasis, melanonychia striata, and onychodystrophy, the 

use of said plasters and methods for prophylaxis and/or treatment of a dysfunction or disorder of nails using said 

plasters. Said dysfunction or disorder of nails may be induced or caused by drugs, systemic diseases, chemical 

compounds, physical influences, fungal, yeast, or bacterial infection of the nails and/or the nail beds, or in the context 

of skin diseases. The plaster shows good therapeutically effects on said dysfunction or disorder of nails without the 

need of drilling a hole into the nail and/or daily scraping of the nail. A preferred embodiment of the plaster consists of 

an occlusive backing layer and a contact layer attached to said backing layer. The contact layer comes in close contact 

with the nail and optionally with the surrounding skin. The contact layer is made of a adhesive, a skin and/or nail 

permeation enhancer, and suitable additives. 







(54) Title of the invention: : NOVEL PIPERIDIN-2,6-DIONE BISULPHATE SALTS AND THEIR 

USE FOR THE TREATMENT OF STRESS-RELATED AFFECTIVE 

DISORDERS 

(51) International classification : A61K 31/45 

(31) Priority Document No : 0120821.4 

(32) Priority Date : 28/08/2001 


KINGDOM 




No 



: PCT/GB2002/00386 

9 

22/08/2002 

: WO 03/020275 A1 

: 

NIL 



No 

: NIL 



PRESTWICK PHARMACEUTICALS, 

INC. 


1825 K STREET N.W., SUITE 1475, 

WASHINGTON DC 20006, USA. 


GITTOS MAURICE WARD 




(57) Abstract: Novel bisulphate salts of certain 3-phenyl-3-dimethylaminoalkyl-4,4-dimethylpiperidin-2,6-diones and 

pharmacologically acceptable solvates thereof are devoid of the weight loss and hepatocyte changes in the rat which limited to 

marginally effective levels the permitted clinical doses of the corresponding hydrochlorides in the treatment or prophylaxis of 

stress-related affective disorders such as anxiety, depression, migraine and sleep apnoea. The preferred bisulphate salts are 

3(3,5-dimethoxyphenyl)-3-(3-dimethylaminopropyl)-4,4-dimethylpiperidine-2,6-dione bisulphate and, especially, 3(3methoxyphenyl)-3-(3-dimethylaminopropyl)-4,4-dimethylpiperidine-2,6-dione 

bisulphate. 

(FIG.- NIL.) 







(PCT/ZA02/00142) 

Date: 13/09/2002 

(54) Title of the invention: SINGLE USE SAFETY SYRINGE 

(51) International classification: A61M 5/00 


(31) Document No.: 1. 2001/7538 

2. 2001/8031 

(32) Date: 1. 13/09/2001 

2. 01/10/2001 

(33) Name of convention country: 

SOUTH AFRICA 

(66) Filed U/s. 5(2): NO 






Application: 


12/03/2004 

MEYER, GYSBERT, ALBERTUS 


4 COBUS OORD, AIRPORT ROAD, 

0017 DOORNPOORT, SOUTH 

AFRICA. 


MEYER, GYSBERT, ALBERTUS 

(57) Abstract: A safety device for a syringe needle which includes a guide and a slidable member having 

a first portion that is configured to be slid along the guide and a second portion having a formation for a 

needle, that facilitates the shielding of the sharp point within said formation. A non-reusable syringe, 

which includes a plunger having a first part with one or more followers and a second part housing a 

guide. 

Figure: 12. 






(PCT/PL02/00063) 

Date: 23/08/2002 


Application: 

16/03/2004 

(54) Title of the invention: THE METHOD TO OBTAIN ENERGY FROM FERROMAGNETIC 

MATERIAL 

(51) International classification: H01F 7/18 


(31) Document No.: P.349299 

(32) Date: 27/08/2001 

(33) Name of convention country: POLAND 

(66) Filed U/s. 5(2): NO 






1. JERZY BRZOZOWSKI 

2. DARIUSZ BRYLINSKI 


1. 1, 05-200 WOLOMIN, POLAND. 

2. 10 M. 25, 78-100 KOLOBRZEG, 

POLAND. 


1. BRZOZOWSKI, JERZY, 

2. BRYLINSKI, DARIUSZ. 

(57) Abstract: In accordance with the method of obtaining effective energy from the ferromagnetic 

material which is the core of electromagnet, its winding is supplied with electric current with such 

intensity that it causes magnetic saturation of the core, and after the work of attracting the armature is 

done, the supply is disconnected without loss of passive energy accumulated in the electromagnet 

inductance. A resonant impulse power supply is used to supply the electromagnet. 

Figure: 1. 






(PCT/DK99/00052) 

Date: 02/02/1999 


Application: 

29/03/2004 

(54) Title of the invention: N –TUPLE OR RAM BASED NEURAL NETWORK CLASSIFICATION 

SYSTEM AND METHOD 

(51) International classification: G06F 15/80 


(31) Document No.: 1. 0162/98 

2. 98201910.1 

(32) Date: 1. 05/02/1998 

2. 09/06/1998 

(33) Name of convention country: DENMARK 

(66) Filed U/s. 5(2): NO 



(63) Divisional to Application No.: 

IN/PCT/2000,00231/MUM 


INTELLIX A/S 


H.C. ORSTEDSVEJ 4, DK-1879 

FREDERIKSBERG, DENMARK. 


1. JORGENSEN, THOMAS, 

MARTINI, 

2. LINNEBERG, CHRISTIAN, 

(64) Filed on: 27/07/2000 

(57) Abstract: The invention relates to a system and a method of training a computer classification 

system which can be defined by a network comprising a number of n-tuples or Look Up Tables (LUTs), 

with each n-tuple or LUT comprising a number of rows corresponding to at least a subset of possible 

classes and comprising columns being addressed by signals or elements of sampled training input data 

examples, each column being defined by a vector having cells with values, the method comprising 

determining the column vector cell values based on one or more training sets of training input data 

examples for different classes so that at least part of the cells comprise or point to information based on 

the number of times the corresponding cell address is sampled from one or more sets of training input 

examples, and determining weight cell values corresponding to one or more column vector cells being 

addressed or sampled by the training examples to thereby allow weighting of one or more column vector 

cells of positive value during a classification process, said weight cell values being determined based on 

the information of at least part of the determined column vector cell values and by use of at least part of 

the training set(s) of input examples. A second aspect of the invention is a system and a method for 

determining - in a computer classification system - weight cell values corresponding to one or more 

column vector cells being addressed by the training examples, wherein the determination is based on the 

information of at least part of the determined vector cell values, said determination allowing weighting of 

column vector cells having a positive value or a non-positive value. Finally the invention provides a 

method and a system for classifying input data examples into a plurality of classes using the computer 

classification systems. 

Figure: 2. 






(PCT/US98/26822) 

Date: 17/12/1998 


Application: 

(54) Title of the invention: A HOME AUDIO/ VIDEO NETWORK 

(51) International classification: H04L 12/28 


(31) Document No.: 09/003,112 

(32) Date: 06/01/1998 


(66) Filed U/s. 5(2): NO 




IN/PCT/2000,00143/MUM 

(64) Filed on: 30/06/2000 

(57) Abstract: A method and system for ensuring future upgradability 

and expandability of devices in a home audio video network. The 

system of the present invention generates a default control module for a 

first device coupled to the network by using a second device coupled to 

the network. The default control module is configured to ensure at least 

a minimum degree of interoperability between the first device and the 

second device. The second device access the first device via the default 

control module, wherein the default control module enables the first 

device to respond to a default set of commands from the second device. 

When an updated control module for the first device is received, the 

default control module is replaced with the updated control module by 

unlinking the default control module and linking the updated control 

module using a registry. The updated control module can be received 

from a wide variety of sources (e.g., the internet, satellite broadcast, 

cable TV provider, disk from the manufacture, etc.). The second device 

subsequently accesses the first device via the updated control module, 

wherein the updated control module enables the first device to respond 

to an updated set of commands from the second device. 

Figure: 15. 


29/03/2004 

SONY ELECTRONICS INC. 


1 SONY DRIVE, PARK RIDGE, NEW 

JERSEY 07656, USA. 


LEA, RODGER, J. 



(19) 




(54) Title of the invention: DEVICE FOR RETAINING SUBSTRATES. 

(51) International Classification: H 01 L 21/00 (71) 




(86) 

05/04/2002 

GERMANY 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


ASTEC HALBLEITERTECHNOLOGIE 

GMBH 


AM ROTHENBUHL 7, 

92348 BERG, 

FEDERAL REPUBLIC OF GERMANY. 


1. NIESE MATTHIAS 

2. FRANZKE JORG 

3. SCHWECKENDIEK JURGEN 




(57) Abstract : The invention concerns a device for 

accommodating substrates (S), particularly wafers or silicon 

substrates used for producing photovoltaic elements. The 

inventive device comprises two walls (1) situated opposite one 

another, whereby at least two rod-like supporting elements (2, 

3) are provided that connect the walls (1), and the supporting 

elements (2, 3) are provided with holding means (5) for 

holding substrates (S) supported on the supporting elements in 

a vertical position oriented parallel to the walls (1). The aim of 

the invention is to enable the substrates to float in the 

treatment bath while simultaneously enabling an easiest 

possible loading and unloading. To this end, at least one rodlike 

supporting counter element is provided, which 


connects both walls 

and is arranged relative to the supporting elements in such a manner as to limit a vertical movement of the 

substrate (S) relative to the walls (1) and to enable the substrates to be loaded or unloaded at an angle to the 

vertical direction. 






(54) Title of the invention: A CONVERTIBLE ELECTRICAL CONNECT SYSTEM. 

(51) International Classification: H 01 R 13/52 (71) 




(86) 

03/10/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A video/data/power quick connect 

system is provided for use with medical appliance 

suspension arms. A universal cable bundle (40) 

extends along a monitor suspension arm (12). A first 

hub harness (50) adapts the cable bundle (40) for 

connection to a first associated source (68) of 

video/data/power signals. A first monitor harness 

(60) connects a lower end of the cable bundle (40) for 

connection to a first associated monitor device (34). 

A second hub harness (50') and second monitor 

harness (60') are provided for adapting the cable 

bundle (40) for connection to a second source (68) of 

associated video/data/power signals and a second 

associated monitor device (34'), respectively. 


(72) 


STERIS INC. 


43425 BUSINESS PARK DRIVE 

TEMECULA, CA 92590, 



RUS STEVEN H. 




( Figure: 02. ) 



(19) 

INDIA (21) Application No: 242/MUMNP/2004 A 


(54) Title of the invention: DRY CLEANING PROCESS. 

(51) International Classification: D 06 L 1/22 (71) 




(86) 

26/10/2001 

EUROPE 





(61) 

(62) 



Filed on N.A. 

Divisional to 




(72) 






MUMBAI – 400 020, 



1. EVERS JOOP 

2. GOEDHART MACHIEL 

3. KERPELS FRED 

4. VAN KRALINGEN CORNELIS G. 

5. OVERDEVEST PIETER E. 

6. REINHOUDT HANK R. 

7. VRIESWIJK KARIN 




(57) Abstract : A sequential process for dry cleaning laundry articles is provided comprising a) at least 

one non-aqueous dry cleaning step, b) at least one low-aqueous dry cleaning step, and, optionally, at least 

one rinsing step. 





(19) 

INDIA (21) Application No: 243/MUMNP/2004 A 


(54) Title of the invention: DRY CLEANING PROCESS. 

(51) International Classification: D 06 L 1/22, 1/04 (71) 




(86) 

26/10/2001 

EUROPE 





(61) 

(62) 



Filed on N.A. 

Divisional to 




(72) 






MUMBAI – 400 020, 



1. EVERS JOOP 

2. GOEDHART MACHIEL 

3. KERPELS FRED 

4. VAN KRALINGEN CORNELIS G. 

5. OVERDEVEST PIETER E. 

6. REINHOUDT HANK R. 

7. VRIESWIJK KARIN 




(57) Abstract : A process for dry cleaning laundry articles comprising at least one dry cleaning step 

followed by at least one regeneration step wherein said regeneration step comprises contacting the articles 

with a regeneration composition comprising 0 to 10 wt.% of a surfactant; 0.001 to 10wt. of water, 0 to 50 

wt% of a cosolvent and the balance being organic dry cleaning solvent, preferably a non-flammable, nonchlorine 

containing organic dry cleaning solvent, wherein the regeneration composition comprises an 

aqueous phase having a pH of at least 5. 









(31) Priority Document No. : PR 8707 



(86) 

PATTERNED SHEETS FOR MAKING HEAT EXCHANGERS AND 

OTHER STRUCTURES. 

07/11/2001 

AUSTRALIA 

International Application : PCT/AU02/01517 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : The invention relates to a 

sheet for making a heat exchanger, heat 

pipe, grill or other structure. The sheet 

includes a repeating three-dimensional 

pattern on both surfaces thereof. The 

pattern includes a plurality of tapered 

projections and depressions arranged 

around a substantially planar central 

region with at least one of the projections 

terminating in a substantially planar end. 

The sheet is stackable with other like 

sheets such that the planar end of the 

sheet contacts a planar central region of 

an adjacent sheet and a repeating pattern 

of interconnected voids is defined 

between the adjacent sheets. 


(72) 


NEPILO PTY LTD. 


38/68 BALMORAL DRIVE, 

MONTVILLE QLD 4560, 

AUSTRALIA. 


BOWERS GEOFFREY 









Application: 14/06/2004 


(54) Title of the : MICROWAVE MEASURING DEVICE FOR DETECTING THE 

invention: CHARGE OF A TWO-PHASE FLOW 


classification 

(31) Priority 

Document No 

: G01N 22/00 

: 101 64 107.9 

(32) Priority Date : 24/12/2001 

(33) Name of 

priority 

country 


Application 

No and Filing 

Date: 


Publication 

No 

: GERMANY 

(61) Patent of 

addition to 

Application 

No 

: NIL 



Application 

No 

: NIL 


: PCT/DE02/04593 

18/12/2002 

: WO 03/056316 

A1 


PROMECON PROZESS-UND 

MESSTECHNIK CONRADS GMBH 


3, D-39179 BARLEBEN, GERMANY 


1. CONRADS HANS GEORG 

2. KLUPSCH VOLKHARD 

3. HALM ALEXANDER 





(57) Abstract: The invention relates to a microwave measuring device for detecting the charge of a twophase 

flow with a gaseous carrier medium containing small and minuscule solid and /or fluid particles and 

for detecting gas contained in a fluid flow, preferably by means of waveguide carrier waves. A preferred 

application of the invention is the detection of solid particles contained in the flow of gas of voluminous 

pneumatic solid matter transport systems used, for example, for pulverized coal furnaces of coal power 

stations. The inventive microwave measuring device is provided with field rods, which protrude into the 

inside of the feed pipe, are arranged before and after a measuring section formed by a transmission antenna 

and a reception antenna, said rods interacting with the feed pipe made of conductive material as a resonator 

for microwaves injected into the feed pipe via the transmission antenna, whereby microwaves that differ 

from the injected microwaves in their plane of polarization and/or phase as a result of diffraction, 

superposition, and/or reflection outside the measuring section are essentially short-circuited in order to 

prevent the results of the measurement from being distorted. The inventive device has the particular 

advantage of being simple to build and easy to install even in voluminous and branched feed pipe systems. 


(FIG.- 1.) 



(19) 




(54) Title of the invention: METHOD TO DETERMINE IN VIVO NUCLEIC ACID LEVELS. 

(51) International Classification: C 12 N 15/10 (71) 




(86) 

18/01/2002 

EUROPE 




Publication No. WO03/060119 A2 

(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


UNIVERSITE LIBRE DE 

BRUXELLES 


ROUTE DE LENNIK 808, 

B-1070 BRUXELLES, 

BELGIUM. 


1. STORDEUR PATRICK 

2. GOLDMAN MICHEL 




(57) Abstract : The invention in particular relates to a method for the quantification of in vivo RNA from 

a biological sample comprising the steps of: collecting said biological sample in a tube comprising a 

compound inhibiting RNA degradation and/or gene induction; forming a precipate comprising nucleic 

acids; separating said precipate from the supermatant; dissolving said precipitate using a buffer, forming a 

suspension; isolating nucleic acids from said suspension using an automated device; 

dispersing/distributing a reagent mix for RT-PCR using an automated device; dispersing/distributing the 

isolated nucleic acids within the dispersed reagent mix using an automated device, and determining the in 

vivo levels of transcripts using the nucleic acid/RT-PCR reagent mix in an automated setup. The present 

invention also relates to the quantitatification of DNA from a biological sample. The present invention 

further elucidates a kit for isolating quantifiable nucleic acids from a biological sample. Applications of 

the method according to present invention are also disclosed. 







(54) Title of the invention: METHOD AND DEVICE RELATED TO A CONTAINER. 

(51) International Classification: E 05 G 1/14 (71) 




(86) 


SWEDEN 

International Application : PCT/SE03/00197 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : The invention pertains to a method and to 

an arrangement applicable to a container or to a chamber, 

for instance to a security chamber or to a security 

container for valuable articles. The container/chamber 

(20) has a casing or shell (10) in which an explosive 

substance or a burstable item is housed. The arrangement 

includes at said shell (10) means (50; 50') for detecting 

ambient temperature or shell temperature. The explosive 

substance is detonated or the burstable item is 

depressurised to prevent bursting of the outer casing/shell 

(10) of the container or said chamber at a predetermined 

temperature limit value. The means (50; 50') for detecting 

the ambient temperature or the shell temperature is 

disposed essentially across the whole surface of the 

shell/casing (10). 


(72) 


SQS SECURITY QUBE SYSTEM AB 


MULLBERGSVAGEN 13, 

S-931 37 SKELLEFTEA, 

SWEDEN. 


LINDSKOG KJELL 







(19) 








(86) 


SPIROAZACYCLIC COMPOUNDS AS MONOAMINE RECEPTOR 

MODULATORS. 

28/12/2001 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


ACADIA PHARMACEUTICALS INC 


3911 SORRENTO VALLEY BLVD., 

SAN DIEGO, CA 92121-1402, 



SCHLIENGER NATHALIE 




(57) Abstract : The present invention relates to spiroazacyclic compounds as monoamine receptor 

modulators; compositions comprising the same; methods of inhibiting an activity of a monoamine 

receptor with said compounds; methods of treating a disease condition associated with a monoamine 

receptor using said compounds; and methods for identifying a subject suitable for treatment using said 

compounds. 







(54) Title of the invention: : PACKET PROCESSOR 

(51) International classification : H04Q 7/32 

(31) Priority Document No : 102 13 733.1 

(32) Priority Date : 26/03/2002 





No 



: NIL 



No 

: PCT/EP03/03101 

15/03/2003 

: WO 03/081927 A1 

: NIL 


(57) Abstract: The invention relates to a mobile terminal for a 

packet-oriented network, especially UMTS, which transmits, 

as a default, speech information in a connection-oriented 

manner. The mobile terminal comprises a module that can be 

preferably retrofitted and that intercepts the speech 

information before it is transmitted in a connection-oriented 

manner in order to divide it up into packets that can be 

transmitted in a packet-oriented manner. 



FG MICROTEC GMBH 


9, 81677 MUNCHEN, GERMANY. 


1. MIRBAHA RAMIN 

2. MIRBAHA VAHID 




(FIG.- 1.) 





(54) Title of the invention: : ELECTRONIC CIRCUITS 

(51) International classification : G06F 1/10 

(31) Priority Document No : 1. 0203605.1 

2. 0212869.2 

3. 0214850.0 

4. 0218834.0 

5. 0225814.3 

(32) Priority Date : 1. 15/02/2002 

2. 06/06/2002 

3. 27/06/2002 

4. 14/08/2002 

5. 06/11/2002 

(33) Name of priority country : GREAT 

BRITAIN 




No 



: NIL 



No 

: PCT/GB03/00719 

14/02/2003 


: NIL 


(57) Abstract: A method of synchronizing a circuit 

comprising the steps of synchronising the circuit globally 

using a high-frequency clock signal, further synchronising 

at multiple lower frequencies by cooperative short-range 

state machines clocked by the high-frequency clock, and 

synchronising the state machines to each other by 

exchanging rollover signals between them. 


] 

(FIG.- 1.) 


MULTIGIG LIMITED 


29-31 MAIN ROAD, WILBY, 

WELLINGBOROUGH, NORTHANT 

NN8 2UB, GREAT BRITAIN. 


WOOD JOHN 









(PCT/GB99/01810) 

Date: 18/06/1999 


Application: 

(54) Title of the invention: COMPOUNDS, COMPOSITIONS AND USE 

(51) International classification: C09B 47/26 


(31) Document No.: 1. 9813475.2 

2. 09/240,602 

(32) Date: 1. 23/06/1998 

2. 01/02/1999 

(33) Name of convention country: UK & USA 

(66) Filed U/s. 5(2): NO 




IN/PCT/2000,00613/MUM 

(64) Filed on: 10/11/2000 


AVECIA LIMITED 

18/08/2004 


HEXAGON HOUSE, BLACKLEY, 

MANCHESTER M9 8ZS, UNITED 

KINGDOM. 


1. MARK KENWORTHY, 

2. COLIN DICK ROBERTSON. 

(57) Abstract: Phthalocyanine compounds of Formula (1) have utility as colorants in inks for ink-jet printing, 

wherein M represents a metal or H; Pc represents a phthalocyanine nucleus; and R 1 represents H or –(CH2)nR 3 ; or 

R 1 and R 2 together with the nitrogen atom to which they are attached represent a 5 or 6-membered ring; where: n 

isindependently an integer from 1 to 30; and R 3 is independently a group selected from hydroxy, sulpho, cyano, - 

SR 4 , -CO2R 5 , -PO3H2 and –NR 6 R 7 ; where: R 4 , R 5 , R 6 and R 7 independently represent H, C1-30alkyl optionally 

substituted by one or more groups selected from hydroxy, mercapto, sulpho, carboxy, cyano and - PO3H2; v is the 

valence of Pc divided by the valence of M; x is from 1.2 to 3.8; y is from 0.1 to 2.7; z is from 0.1 to 2.7; and x, y 

and z satisfy 2 ≤ x + y + z ≤ 4. 

Figure: NIL. 






(PCT/RU99/00264) 

Date: 29/07/1999 


Application: 


(54) Title of the invention: METHOD FOR CARRYING OUT TRANSACTIONS AND DEVICE 

FOR REALISING THE SAME 

(51) International classification: G07F 7/10 


(31) Document No.: 98120922 25 

(32) Date: 25/11/1998 

(33) Name of convention country: RUSSIA 

(66) Filed U/s. 5(2): NO 





1. ZOLTAREV OLEG ANATOLIEVICH 

2. KUZNETSOV IVAN 

VLADIMIROVICH 

3. MOSHONKIN ANDREI 

GENNADIEVICH 

4. SMIRNOV ALEXANDR 

LEONIDOVICH 

5. KHAMITOV ILDAR 

MAGAFUROVICH 




(57) Abstract: The present invention relates to method for carrying out 

transactions and, during transactions on open telecommunication 

networks, for protecting the financial interests of each participant in the 

transaction against unauthorized actions by other participants. This 

method is used for protecting the privacy between payers and recipients 

and for carrying out transactions ranging from microtransactions to 

business transactions, the transactions being subordinated in time to the 

rapidity of action or the network connections only regardless of the 

transaction amount. This method also allows to serve a number of 

clients that increases proportionally with the resources of the transaction 

system operator, can be easily integrated in any trade system, allows 

each client to make and receive payments and can be used for making 

transactions between the clients of different banks. This method for 

carrying out transactions is implemented in a software environment. 


1. 25-20, SOSNOVY BOR 

LENINGRADSKAYA OBL, 

188537, 

2. 48-56, ST. PETERSBURG, 191123, 

3. 44-A-5, ST. PETERSBURG, 

191123, 

4. 36-8, ST. PETERSBURG, 191123, 

5. 29-2-45, ST. PETERSBURG, 

191123, 

ALL ARE RUSSIAN. 





(PCT/GB99/04139) 

Date: 09/12/1999 

1. ZOLOTAREV, OLEG 

ANATOLIEVICH UL. 

2. KUZNETSOV, IVAN 

VLADIMIROVICH UL. 

3. MOSHONKIN, ANDREI 

GENNADIEVICH UL. 

4. SMIRNOV, ALEXANDER 

LEONIDOVICH UL. 

5. KHAMITOV, ILDAR 

MAGAFUROVICH UL. 


Application: 

Figure: NIL. 

30/08/2004 

(54) Title of the invention: A NON-BLEACHING LAUNDRY DETERGENT COMPOSITION 


(51) International classification: C11D 3/33 


(31) Document No.: 1. 9827225.5 

2. 9927101.7 

(32) Date: 1. 10/12/1998 

2. 16/11/1999 



(66) Filed U/s. 5(2): NO 




IN/PCT/2001/00627/MUM 

(64) Filed on: 01/06/2001 





165/166 BACKBAY RECLAMATION, 


INDIA. 


1. EBBRELL, LESLEY, 

2. FINCH, TIMOTHY DAVID, 

3. JONES, DAVID PHILIP, 

4. WARR, JONATHAN FRANK. 

(57) Abstract: A non-beaching laundry detergent composition comprises surfactant, builder, and optionally other 

non-bleach detergent ingredients, and also contains from 0.05 to 2.5 wt% of iminodisuccinate (IDS) 

hydroxyiminodisuccinate (HIDS). The composition provides improved maintenance and/or restoration of colour 

fidelity during the wash, especially at low wash pH. The IDS or HIDS is also an effective chlorine scavenger, 

reducing the in-wash fading of chlorine-sensitive dyes. In addition, the incorporation of the IDS or HIDS improves 

the stain removal performance of the composition. 

Figure: NIL. 



(19) 




(51) International Classification: C 07 F 3/02 (71) 




(86) 


PROCESS FOR CHLOROSILANE INTERMEDIATES 

MANUFACTURE. 

04/04/2002 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 


DOW CORNING CORPORATION 


2200 WEST SALZBURG ROAD, 

MIDLAND, MI 48686-0994, 



1. NGUYEN BINH T. 

2. BEDBURY CURTIS J. 

3. CANNADY JOHN P. 




(57) Abstract : Process for the preparation of phenyl Grignard reagents in co-solvents of toluene and 

ether and, the preparation of phenylclorosilane intermediates using co-solvents of toluene and ether 

essentially in a one step process. The phenychlorosilanes in the process of this invention are important 

intermediates for the preparation of various silicone materials. 





(19) 




(51) International Classification: C 07 F 7/08 (71) 




(86) 


PROCESS FOR PREPARING PHENYLORGANOSILICON 

INTERMEDIATES. 

04/04/2002 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 





MIDLAND, MI 48686-0994, 





3. CANNADY JOHN P. 




(57) Abstract : A method for preparing phenyl-containing organosilicon intermediates using an aromatic 

halogenated solvent during the coupling reaction involving a phenyl Grignard reagent and a precursor 

silane. The process comprising contacting a phenyl halide with magnesium in a solvent such as ether, or 

an aromatic halogenated/ether solvent mixture to form a Grignard reagent, and contacting the Grignard 

reagent with a precursor chlorosilane in aromatic halogenated solvent to form the desired organosilicon 

intermediates, and then filtering and distilling to acquire the organosilicon intermediate reaction product. 





(19) 








(86) 


GRIGNARD PREPARATION OF UNSATURATED ORGANIC 

COMPOUNDS. 

04/04/2002 

U.S.A. 





(61) 

(62) 



Filed on N.A. 

Divisional to 



(72) 





MIDLAND, MI 48686-0994, 








(57) Abstract : A Grignard-type process for the preparation of unsaturated organic compounds. The 

process comprises contacting an unsaturated organic halide with magnesium metal in a mixture of ether 

and a polar halogenated hydrocarbon co-solvent, filtering the reaction product from the reaction step and 

thereafter, treating the reaction product filtrate from the filtration step to obtain the desired unsaturated 

organic compounds. 







(54) Title of the invention: A PACKAGE AND A METHOD OF FILLING THEREOF. 





(86) 

03/05/2002 

SWEDEN 

International Application : PCT/SE03/00683 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A package comprising a bag of flexible sheet 

material which, prior to being filled, is laid flat and comprises two 

opposing side walls (2) substantially in contact with each other, 

which side walls are tightly sealed along opposing side edges (5), the 

bag also comprising a bottom wall (3) which is folded double and 

has two fields (31) facing each other received between the lower 

parts of the side walls (2), the parts of the end edges of the bottom 

wall being sealed together. At least in the vicinity of the fold line 

(32), the side edges of the bottom wall are joined to the side walls at 

their side edges and a string of springy, elastic material (4) is 

connected to a respective side wall (2) at its lower edge (21), along 

substantially the entire length of the lower edge of the side wall 

when the package is in its flat state, and the two material strings are 

separated from each other. The package is filled by inserting a 

substantially leaf-shaped pouring mouthpiece into the flat neck of the 

package and introducing liquid through the mouthpiece, after which 

the neck of the package is sealed. The packages may be joined 

together in a coherent chain of packages attached to each other at 

their side edges. 


(72) 


VILHO ERIKSSON 


OSTRA HENRIKSBERGSVAGEN 45, 

S-131 31 NACKA, SWEDEN. 


- IDEM - 









(54) Title of the invention: CRACKING FURNACE WITH MORE UNIFORM HEATING. 

(51) International Classification: C 10 G 9/20 (71) 




(86) 

10/04/2002 

U.S.A. 

International Application : PCT/US03/11064 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : A cracking furnace for the 

pyrolysis heating of an organic feedstock includes 

a heating section and at least one convection 

section. In one embodiment the furnace includes 

first and second convection sections positioned 

along opposite sides of the heating section. The 

openings for admitting flue gas to the convection 

sections can be at the top or the bottom of the 

heating section. In another embodiment the 

furnace includes a plurality of passageways for 

the communication of flue gas from the heating 

section to the convection section. The 

passageways can be positioned at the top or the 

bottom of the heating section. The passageways 

provide a more even flow of flue gas through the 

heating section by preventing recirculation of the 

flue gas within the heating chamber. 


(72) 








1. PLATVOET ERWIN M. J. 

2. ALBANO JOHN 

3. McCARTHY FRANK D. 

4. FELL PAUL J. 







(19) 




(54) Title of the invention: METHODS AND SYSTEMS FOR DIGITAL DATA TRANSMISSION. 

(51) International Classification: H 04 L 27/26 (71) 

(31) Priority Document No. : PCT/RU02/ 

00101 

(32) Priority Date : 20/03/2002 


(86) 

RUSSIA 

International Application : PCT/RU02/ 

00101 



Publication No. WO03/079 

625 A1 

(61) 

(62) 



Filed on N.A. 

Divisional to 




1. DOUNAEV IGOR BORISOVICH 

2. LETOUNOV LEONID ALEXEEVICH 


1. UL GOGOLYA, 14A-48, KHIMKI, 

MOSKOVSKAYA OBL 141400, 

RUSSIAN FEDERATION. 

2. MZHK “SOLNECHNY”, 2-105, 

GOMEL, 246050, BELARUS. 


- IDEM - 




(57) Abstract : The inventive methods and systems for digital data transmission using a communication 

path which comprises analog communication lines and a pulse-code modulation channel (PCM). Said 

method and systems make it possible to increase a data transmission rate through the entire communication 

path in such a way that it is equal to the data transmission rate of the PCM channel irrespective of the 

quality of used analog communication lines. The spectrum of a signal transmitted by an analog transmission 

line is selected such that the data transmission rate of said transmission line is equal to the data transmission 

rate of the PCM channel, and the number of data quantisation levels transmitted by the analog transmission 

line is as low as possible for said analog communication line. In order to convert an analog signal into an 

PCM channel signal, the analog-signal frequency is decreased proportionally the ratio between the number 

of data quantisation levels transmitted by a PCM channel and the number of data quantisation levels 

transmitted by the analog communication line. 





(19) 






(32) Priority Date : 28/08/2002 


(86) International Application : PCT/EP03/009030 




(61) 

(62) 



Filed on N.A. 

Divisional to 



(57) Abstract : In regenerating an electroless metal 

plating bath by electrodialysis, it has been found that the 

metal of the metal plating bath deposits in the electrolysis 

arrangement. To overcome this problem, an improvement 

to prior art regenerating devices is suggested, said 

improvement consisting in providing main cation 

exchangers for removing ions of this metal from a 

concentrate fluid. The main cation exchangers are coupled 

to the concentrate compartments of the electrolysis 

arrangement in such a manner that the concentrate fluid 

flowing through the concentrate compartments is allowed 

to pass through the main cation exchangers and to be 

recirculated back into the concentrate compartments. 



DEVICE AND METHOD FOR REGENERATING AN 

ELECTROLESS METAL PLATING BATH. 

(72) 


ATOTECH DEUTSCHLAND GMBH 


ERASMUSSTRASSE 20, 

10553 BERLIN DEUTSCHLAND, 

GERMANY. 


1. HEYDECKE JENS 

2. MURANUSHI MASANORI 



Publication After 18 month 



(21) Application No.: 


505/MUMNP/2004 

PCT/ AU01/007444 

Date: 21/06/2001 

(51) International classification: G 06 F 17/60 (71) 

(30) Priority Data : 

(31) Document No.: 1) PQ 8221 2) PQ 9697 

(32) Date : 1) 21/06/200 2) 28/08/2000 

(33) Name of convention country : AUSTRALIA 

(66) Filed U/s. 5(2) : NO (72) 


(62) Filed on : N.A. 


Application No.: IN/PCT/2002,01841/ MUM 



An interactive on line marketing system 

which allows the marketing by a supplier of 

products and/or services to a remote 

participant consumer through a supplier web 

site established by a host provider, wherein 

said remote participant consumer 

participates in an on line game, competition 

or the like via said supplier web site in return 

for providing an identifying consumer 

profile, pin number or the like to the web 

site of said supplier of goods and/or services; 

wherein the supplier of goods and services 

directly interacts with consumers of the 

providers goods and/or services or via the 

host. 

Figure: 01. 

A (22) Date of filing of 

Application: 

13/09/2004 

INTERACTIVE ON LINE MARKETING SYSTEM AND 

METHOD THEREFOR. 


THE ONLY COMPANY PTY LTD. 


75 OLD PITWATER ROAD, 

BROOKVALE, NSW 2100, 

AUSTRALIA. 

Name of the Inventors 

01. SHORTER ANTHONY 







506/MUMNP/2004 

PCT/ JP 99/06424 

Date: 17/11/99 

(51) International classification: G 06 F 17/60 (71) 


(31) Document No.: 10/327019 

(32) Date : 17/11/1998 

(33) Name of convention country : AUSTRALIA 

(66) Filed U/s. 5(2) : NO 




Application No.: IN/PCT/2002,00169/ MUM 

(64) Filed on :N.A. 


A terminal capable of communicating with a 

charging center, a charging system, and data 

processing center are disclosed. A point memory 

(45) of a recording/reproducing device (10) holds 

charging point information. An HDD (15) holds 

information sent from an external source. A CPU 

(11) updates the charging point information stored in 

the point memory (45) when the information sent is 

stored in the HDD (15), and updates the attributes of 

the information sent. Thus the disadvantage that it is 

necessary to communicate with a delivery/charging 

center (1) each time information is sent to the 

recording/reproducing device (10) is eliminated. 

Figure: 03. 


Application: 

13/09/2004 

TERMINAL CHARAING AND DATAPROCESSING 

METHOD. 

(72) 


SONY CORPORATION JAPAN. 


7-35 KITASHINAWA 6-CHOME, 

SHINAGAWA-KU, TOKYO, 

141-001, JAPAN. 


1. YODO FUMITAKE. 







507/MUMNP/2004 

PCT/ CA04/000055 

Date: 15/01/2001 

(51) International classification: B 60 G 7/00 (71) 


(31) Document No.: 2,416,703 

(32) Date : 20/01/2003 

(33) Name of convention country : CANADA 

(66) Filed U/s. 5(2) : NO 




(64) Filed on : N.A 


A vehicular suspension arm (10) comprises an upper 

sheet metal stamped component (11) with a first outer 

face and a first inner face (19), and a first central web 

portion (17) with two opposites sides and first 

upstanding flange portions (13) at opposites sides of the 

first web portion, a lower sheet metal stamped 

component (12) with a second outer face and a second 

inner face (19), and a second central web portion (17) 

with two opposite sides and a second upstanding flange 

portions (13) at the opposite sides of the second web 

portion, the first and second inner faces (19) adapted to 

contact each other along a substantial portion of the first 

and second web portions (17), the upper and lower 

stamped components (11, 12) adapted to be rigidly 

attached to each other to create a structural I-beam 

section, wherein the thickness of each upstanding flange 

portion (13) is at least equal to the combined thickness 

of the first and second web portions (17). 

Figure: 06. 


Application: 

14/09/2004 

STRUCTURAL I- BEAM AUTOMOTIVE SUSPENSION 

ARM. 

(72) 


MULTIMATIC INC. 


85 VALLEYWOOD DRIVE, 

MARKHAM, ONTARIO L3R 5E5, 

CANDA. 


1. HOWELL ROBERT 

ALEXANDER 

2. GRUBER RUDOLF 






508/MUMNP/2004 

PCT/ GB03/00836 

Date: 27/02/2003 


Application: 

(54) Title of the invention: PURIFICATION OF CITALOPARAM. 

(51) International classification: B 60 G 7/00 (71) 


(31) Document No.: 0204682.9 

(32) Date : 27/02/2003 

(33) Name of convention country : GREAT 

BRITAIN 

(66) Filed U/s. 5(2) : NO 

(61) Patent of addition to application No.: NIL (72) 






CIPLA LIMTED. 

15/09/2004 


289 BELLASIS ROAD, 

MUMBI CENTRAL, 

MUMBAI 400 008, 

INDIA. 


1. HAMIED YUSUF KHWAJA 

2. KANKAN RAJENDRA N 

3. RAO DHARMARAJ 

Crude citalopram base is purified adsorption on a solid support, washing the support to selectively remove 

impurities, and releasing the purified base from the support. 

Figure: NIL 







509/MUMNP/2004 

PCT/ ep00/03717 

Date: 19/04/2000 

(51) International classification: C 12 N 15/13 (71) 


(31) Document No.: 99303117.8 

(32) Date : 22/04/1999 

(33) Name of convention country : EUROPE 

(66) Filed U/s. 5(2) : NO 




Application No.: IN/ PCT/2001/01267/MUM 




Application: 

15/09/2004 

INHIBITION OF VIRAL INFECTION USING 

MONOVALENT ANTIGEN- BINDING PROTEINS. 

(72) 





165/166,BACKBAY 

RECLAMATION, 

MUMBAI-400020, 



1. BEZEMER SANDRA 

2. FRENKEN LEON 

3. DE HARDJOGEN 

4. LEDEBOER ADRIANUS 

5. VERRIPS CORNELIS 

A method of inhibiting viral infection using a monovalent antigen binding protein comprising a 

single domain binding unit capable of binding to a virus is described. Preferably the protein is a 

heavy chain variable domain derive from an immunoglobulin naturally devoid of light chains. 

Food pharmaceutical and cosmetic products comprising such proteins are also described together 

with a method for selecting inhibiting proteins from a large population of mainly containing noninhibiting, 

but infectious agent binding fragments. 

Figure: NIL 






511/MUMNP/2004 

PCT/ EP03/04134 

Date: 22/04/2003 


Application: 

(54) Title of the invention: NITROSATED IMIDAZOPYRIDIENS. 

(51) International classification: C 07 D 471/14 (71) 


(31) Document No.: 02009104.7 

(32) Date : 24/04/2002 

(33) Name of convention country : EPO 

(66) Filed U/s. 5(2) : YES 







ALTNA PHARMA AG. 

15/09/2004 


BYK-GULDEN-STRASSE2, 

D-78467 KONSTANZ, 

DEUTSCHLAND, 

GERMANY. 


1. POSTIUS STEFAN 

2. HANAUER GUIDO 

3. KROMER WOLFGANG 

4. SIMON WOLFGANG 

ALEXANDER 

The invention relates to nitrosated imidazopyridines of a certain formula (I), in which the 

substituents and symbols have the meanings indicated in the description. The compounds have 

gastric secretion-inhibiting, anti-inflammatory and antibacterial properties. 

Figure: ( I ) 






513/MUMNP/2004 

PCT/ EP03/02056 

Date: 28/02/2003 


Application: 

16/09/2004 

(54) Title of the invention: LOW PH HIGH SKIN FRICTION COSMETIC CREAMS. 

(51) International classification: A 61 K 7/48 (71) 


(31) Document No.: 10/104,464 

(32) Date : 22/03/2002 

(33) Name of convention country : U.S.A. 

(66) Filed U/s. 5(2) : NO 











RECLAMATION, 




1. ZHOU YAN 

2. SURIANARAYANAN 

RAMESH 


4. SONA PUSHKER 

5. BARRATT MICHAEL JAMES 

A high skin friction cosmetic composition that can provide the consumer-desired sensory 

properties of traditional vanishing creams, stable at low pH, containing solid asymmetric and 

an anionic emulsifier having pKa values of less than about 4.5. The composition preferably 

further includes an acidic skin benefit agent. A method of controlling or preventing an oily 

skin appearance and/or feel especially in the facial area, by applying to the skin the inventive 

composition is also disclosed. 

Figure: NIL 







514/MUMNP/2004 

PCT/ EP03/02658 

Date: 13/03/2003 



(31) Document No.: 60/366,689 

(32) Date : 22/03/2002 


(66) Filed U/s. 5(2) : NO 







Application: 

16/09/2004 

STABILIZATION OF TERPENOIDS IN COSMETIC 

COMPOSITIONS. 

(72) 






RECLAMATION, 




1. KERSCHNER JUITH LYNNE 

2. LOVE ARTHUR RAY 

3. BARRATT MICHEL JAMES 

Cosmetic composition containing terpenoids along with a 4-substiuted resorcinol derivative 

exhibit improved storage stability and oxidative stability. 

Figure: NIL 







515/MUMNP/2004 

PCT/ EP03/02656 

Date: 13/03/2003 



(31) Document No.: 60/366,908 

(32) Date : 22/03/2002 


(66) Filed U/s. 5(2) : NO 







Application: 

16/09/2004 


COMPOSITIONS. 

(72) 






RECLAMATION, 




01. KERSCHNER, JUITH LYNNE 



04. ZHOU YAN 


Cosmetic compositions containing organic sunscreens along with a 4-substituted resorcinol derivatives of general formula I exhibit improved 

storage stability and oxidative stability, where each R1 and R2, independently, represents a hydrogen atom, -CO-R (acyl group), -COO-R, CONHR; 

where R represents saturated or unsaturated, linear, branched or cyclic C1 - C18 hydrocarbon groups; and R3 represents (1) an alkyl group, having 

from 1 to 18 carbon atoms, preferably having from 2 to 12 carbon atoms, with or without substitution of one or more hydrogen atoms of a linear 

alkyl group with a methyl or ethyl group; e.g., R3 constitutes linear or branched chain alkyls, or (2) a group of the general formula (II), where X is 

preferably H, n is 0 to 3 and the dashed lines represents an optional double bond. 

Figure: ( I & II ) 







516/MUMNP/2004 

PCT/ EP03/02655 

Date: 13/03/2003 



(31) Document No.: 60/366,924 

(32) Date : 22/03/2002 


(66) Filed U/s. 5(2) : NO 







Application: 

16/09/2004 


COMPOSITIONS. 

(72) 






RECLAMATION, 




01. KERSCHNER, JUITH LYNNE 



04. ZHOU YAN 

Cosmetic compositions containing a micronized metal oxide along with a 4-substituted resorcinol 

derivatives of the general formula I exhibit improved storage stability: (I) where each R1 and R2, 

independently, represents a hydrogen atom, -CO-R (acyl group), -COO-R, CONHR; where R 

represents saturated or unsaturated, linear, branched or cyclic C1 - C18 hydrocarbon groups; and 

R3 represents (1) an alkyl group, having from 1 to 18 carbon atoms, preferably having from 2 to 

12 carbon atoms, with or without substitution of one or more hydrogen atoms of a linear alkyl 

group with a methyl or ethyl group; e.g., R3 constitutes linear or branched chain alkyls, or (2) a 

group of the general formula (II) wherein X is preferably H, n is 0 to 3 and the dashed lines 

represents an optional double bond. 


Figure: ( I & II ) 




21) Application No.: 

517/MUMNP/2004 

PCT/ EP00/00906 

Date: 04/02/2000 

(54) Title of the invention: COLD BREW TEA 

(51) International classification: A 23 F 3/10 (71) 


(31) Document No.: 60/119,102 

(32) Date : 08/02/1999 


(66) Filed U/s. 5(2) : NO 




Application No.: IN/PCT/2001,00946/MUM 




Application: 

(72) 


16/09/2004 





RECLAMATION, 




01. BALENTINE DOUGLAS 

ASHLEY 

02. GOBBO STEVEN ALPHONSE 

03. QI XIAOGUN 

04. HANG ROBERT STEVEN 

05. PARRY ANDREW DAVID 

06. GOODSALL CHRISTOPHER 

WILLIAM 

A cold water infusible tea leaf product is disclosed which brews in cold water to product an iced 

tea beverage with the color and flavor of iced teas prepared by not brewing methods. The product 

when brewed in water at about 15ºC for about 5 minutes at a water to tea ratio of 100 water to 1 

tea has a cold water infusion hunter L value of about 25 to 45; a hunter “a” value of about 24 to 34: 

a Hunter haze value of less than 40 and at least 0.15% soluble tea solids. 

Figure: NIL 






518/MUMNP/2004 

PCT/IL03/00215 

Date:13/03/2003 

(54) Title of the invention: BRAINSGATE LTD. 

(51) International classification: A 61 N 1/18 (71) 


(31) Document No.: 60/364,829 

(32) Date : 14/03/2002 


(66) Filed U/s. 5(2) : NO 








Application: 

(72) 

An implantable device (20) uses the carotid baroreflex in 

order to control systemic blood pressure. The implant 

includes sampling and pulse stimulation electrodes (44) 

preferably located on the carotid sinus nerve branch of the 

glossopharyngeal nerve, adjacent and distal to the carotid 

sinus baroreceptors. The stimulators have an external control 

unit, which communicates with the implant for determining 

appropriate operational parameters, and for retrieving 

telemetry information from the device's data bank. Typically 

two internal devices are implanted, one at each side of the 

patient's neck. 

Figure: 03. 


16/09/2004 

TECHNIQUE FOR BLOOD 

PRESSURE REGULATION 


BEIT HA TAMER, 

17 HA TIDHAR STREET, 

43654 RA ANANA, 

ISRAEL. 


01. SHALEV ALON 






519/MUMNP/2004 

PCT/US03/04936 

Date: 18/02/2003 


Application: 

17/09/2004 


ACOUSTIC POSITION MEASUREMENT SYSTEM FOR 

WELL BORE FORMATION. 

(51) International classification: E21 B 47/026 (71) Name of the Applicant: 

(30) 

(31) 

Priority Data : 

Document No.: 10/079.794 

CDX GAS LLC. 

(32) Date : 19/02/2002 


(66) Filed U/s. 5(2) : NO 






An acoustic position measurement system (23) 

and method includes an acoustic transmitter 

operable to transmit a sound wave into an 

underground well bore (18) in a target 

formation (26). The sound wave is configured 

to reflect from a boundary formation (28,29) 

proximate the target formation. The system 

includes an acoustic receiver operable to 

receive a reflected sound wave. The reflected 

sound wave comprises a reflection of the 

sound wave from the boundary formation. The 

system also includes an electronics portion 

electrically coupled to the acoustic receiver. 

The electronics portion is operable to process 

the reflected sound wave and produce, based 

upon a characteristic of the reflected sound 

wave, data output indicative of a position of 

the acoustic position measurement system in 

the target formation. 

Figure: 01. 

(72) 


SUIT 280, 5485 BELTLINE ROAD 

DALLAS, TX 75240-7656 

USA 


01ZUPANICK JOSEPH A 

02 RIAL MONTY H 

03. LOCKERD ROBERT 

MICHAEL SR 



The following Patent application have been published under Section 11A of the 

Patents 



520/MUMNP/2004 

PCT/EP01/14264 

Date:03/12/2001 

(54) Title of the invention: FOOD COMPOSITION. 

(51) International classification: A 23 D 7/00 (71) 


(31) Document No.: 00204763.7 

(32) Date : 21/12/2000 

(33) Name of convention country : EUROPE 

(66) Filed U/s. 5(2) : NO 




No.: PCT/IL/03/00215/MARCH13,2003 




Application: 

(72) 


20/09/2004 




165/166,BACKBAY RECLAMATION, 




01. T HOOFT COR 

02. VAN DEN KOMMER 

MARCELLE 

03. SEGERS JACOBUS CORNELIS 

The invention concerns a food composition, suitable for shallow frying comprising triglycerides, 

wherein least 60 wt% of triglycerides is of vegetable origin and 0.05-3 wt% sunflower lecithin 

further concerns a process for the preparation of hydrolyzed sunflower lecithin. 

Figure: NIL 







522/MUMNP/2004 

PCT/US99/25939 

Date:03/11/1998 

(51) International classification: G 06 F17/30 (71) 


(31) Document No.: 09/185.042 

(32) Date : 03/11/1998 

(33) Name of convention country : U. S. A. 

(66) Filed U/s. 5(2) : NO 







Application: 

21/09/2004 

METHOD AND APPARATUS FOR OPTIMIZING 

QUERY GENERATION BY SELECTIVELY UTILZING 

ATTRIBUTES OR KEY VALUES. 

(72) 


PLATINUM TECHNOLOGY INC. 


ONE COMPUTER ASSOCIATES 

PLAZA, ISLANDIA, 

NEW YORK11749, U.S.A. 


01. KRYCHNIAK PIOTR JACEK 


A method of joining two or more sets of data in a database (6) is provide wherein certain 

dimension (12) in the fact data are designed as being forced dimension, and wherein for each 

forced dimension, a set of entries is created in the fact data each with the same key values in all 

of the dimension other than the forced dimension, and each with a different member of the set of 

values existing in the fact data for that dimension, if and only if at least one entry exists in the 

fact data with the same set of key values in the dimension other than the forced dimension. 

Figure: NIL 






523/MUMNP/2004 

PCT/US99/25938 

Date:03/11/1999 


Application: 

(54) Title of the invention: A SYSTEM FOR AGGREGATING DATA. 

(51) International classification: G 06 F17/30 (71) 


(31) Document No.: 09/185.366 

(32) Date : 03/11/1998 

(33) Name of convention country : U. S. A. 

(66) Filed U/s. 5(2) : NO 







A system is provided for selecting an 

appropriate aggregated fact data table (20) to 

use as the basis for calculating an aggregation 

request from a set of stored aggregated fact 

data tables (22). An estimate is established of 

the amount of processing time required to 

aggregate each of the tables. The table with 

the lowest estimate is then used to perform the 

aggregation. 

Figure: 01. 

(72) 


21/09/2004 

PLATINUM TECHNOLOGY INC. 


ONE COMPUTER ASSOCIATES 

PLAZA, ISLANDIA, 

NEW YORK11749, U.S.A. 


01 ROGERS JAMES P 






524/MUMNP/2004 

PCT/IE03/00012 

Date: 27/10/2003 


Application: 

(54) Title of the invention: RESETTABLE SWITCHING DEVICE. 

(51) International classification: H 01 H 51/01 (71) 


(31) Document No.: S020199 

(32) Date : 21/03/2002 

(33) Name of convention country : IRELAND 

(66) Filed U/s. 5(2) : NO 







TRIPCO LIMITED. 

21/09/2004 


ATREUS PLACE, POOLBOY, 

BALLINASLOE, 

COUNTRY GALWAY, 

IRELAND. 


01. WARD PATRICK 



A resettable switching device, e.g. a relay, 

comprises a fixed contact (18) and a movable 

contact (28). A solenoid (12) is fixed relative to the 

fixed contact and a ferromagnetic plunger (20) 

carries the movable contact. A spring (24) biases 

the plunger away from the fixed contact so the 

device is normally open. When the device is set a 

further ferromagnetic element, e.g. a plunger (22), 

holds the first plunger (20) in a closed-contact 

position by magnetic attraction against the action 

of the spring (24). When a predetermined current 

condition exists in the solenoid the magnetic 

attraction between the element and plunger is 

reduced below the level necessary to hold the 

plunger so that the movable contact disengages the 

fixed contact. 

Figure: 01. 






525/MUMNP/2004 

PCT/US03/09507 

Date: 31/03/ 2003 


Application: 

(54) Title of the invention: RESETTABLE SWITCHING DEVICE 

(51) International classification: A 23 L 1/20 (71) 


(31) Document No.: S020199 

(32) Date : 21/03/2002 

(33) Name of convention country : IRELAND 

(66) Filed U/s. 5(2) : NO 







TRIPCO LIMTED. 

22/09/2004 


ATREEUS PLACE, 

POOLBOY, BALLIN ASLOE, 

COUNTRY GALWAY, 

IRELAND. 


01. WARD PATRICK. 

Disclosed is method for improving flavor quality and reducing water absorption of protein 

isolates, particularly soy protein concentrates. The method involves a surface treatment of the 

protein isolates with an aqueous solution containing a polysaccharide in order to coat the protein 

isolates and block off the flavor of the protein molecule as well as serving as a moisture barrier. 

The treated protein isolates are then dried to a powder from. The resulting protein isolates are 

bland in taste, have a reduced water adsorption ratio as compared to the untreated protein 

isolates and can be used in a wide range of food products without flavor reversion. 

Figure: NIL 







528/MUMNP/2004 

PCT/US01/03885 

Date: 07/02/2001 

(51) International classification: G 01 N 27/49 (71) 


(31) Document No.: 09/499,421 

(32) Date : 07/02/2000 


(66) Filed U/s. 5(2) : NO 





(57) Abstract: An electrochemical sensor (A, A') is 

specific for the detection of peracetic acid in a solution 

which also contains hydrogen peroxide. A potential is 

applied between a reference electrode (120, 120') and a 

working electrode (118, 118'). A read voltage (fig. 7) is 

selectively pulsed to the working electrode and then 

through the solution to a counter electrode (122, 122'). The 

current flowing between the working electrode and the 

counter electrode is dependent on the peracetic acid 

concentration in the solution (fig. 6). By careful selection 

of the read voltage, the contribution of hydrogen peroxide 

to the current flow is virtually negligible. The sensor 

effectively measures peracetic acid concentrations in the 

range generally employed in sterilization and disinfection 

baths (100-3000 ppm.). 

Figure: 02. 


Application: 

23/09/2004 

ELECTROCHEMICAL SENSOR FOR THE SPECIFIC 

DETECTION OF PERACETIC ACID IN AQUEOUS 

SOLUTIONS USING PULSE AMPEROMETRIC METHODS. 

(72) 


STERIS INC. 


43425 BUSINESS PARK DRIVE 

TEMECULA, CA 92590, 

U.S.A. 


01. MCVEY IAIN F. 

02. DESANTIS BRIAN J. 

03. LEWANDOWSKI JAN J. 

04. THOMAS KAREN L. 

05. SCHINDLY BRIAN E. 






529/MUMNP/2004 

PCT/EP03/02105 

Date: 28/02/2003 


Application: 


(54) Title of the invention: SOILD FABRIC CONDITIONING COMPOSITIONS. 



(31) Document No.: 0207481.3 

(32) Date : 28/03/2003 

(33) Name of convention country : UNITED 

KINGDOME 

(66) Filed U/s. 5(2): NO 














01. GREGORY DENIS JAMES 

02. WYLDE SARAH 

A solid fabric conditioning composition comprises from 15 to 75% weight of cationic softening 

material (active ingredient), based on the total weight of the composition; one or more carrier 

materials and 50% or less by weight of the composition of one or more zeolites. 

Figure: NIL 






530/MUMNP/2004 

PCT/EP03/02106 

Date:28/02/2003 


Application: 





(31) Document No.: 0207483.9 

(32) Date : 28/03/2002 


KINGDOME 

(66) Filed U/s. 5(2) : NO 



(63) Divisional to Application No.: NO 



(72) 






RECLAMATION, 




01.GREGORY DENIS JAMES 

02.PETKOV JORDAN TODOROV 


A solid fabric conditioning composition comprises a cationic fabric softening agent one or more 

carrier materials, perfume and a deposition aid for depositing the cationic fabric softening agent onto 

fabric during a laundry treatment operation wherein the deposition aid is citric acid or a salt of citric 

acid. 

Figure: NIL 






531/MUMNP/2004 

PCT/EP03/02108 

Date: 28/02/2003 


Application: 





(31) Document No.: 0207484.7 

(32) Date : 28/03/2002 


KINGDOME 

(66) Filed U/s. 5(2) : NO 






quaternary ammonium material of the formula: 

[(CH2)n(TR)]m X R-N-[(CH2)n(OH)]3-m 

wherein each R is independently selected from a C5-35 

alkyl or alkenyl group, R1 represents a C1-4 alkyl, C2-4 

alkenyl or a C1-4 hydroxyalkyl group, T is -O-C- or -C-O-, 

n is 0 or a number selected from 1 to 4, m is 1, 2 or 3 and 

denotes the number of moieties to which it relates that pend 

directly from the N atom, and X is an anionic group, 

such as halides or alkyl sulphates, has a mean particle size of 

from 100 to 1200 m. The material is provided in a solid 

fabric conditioning composition at a level of from 1 to 

45wt% in combination with a carrier material. 

Figure: NIL 









01. GREGORY DENIS JAMES 








532/MUMNP/2004 

PCT/A03/00261 

Date:24/02/2003 

(51) International classification: B 60 L 9/02 (71) 


(31) Document No.: 10/083,587 

(32) Date : 27/02/22/002 

(33) Name of convention country : USA 

(66) Filed U/s. 5(2) : NO 


(62) Filed on : N.A. (72) 




A control system for individually controlling 

power from a single voltage source to a 

plurality of motors is described. A chopper 

circuit, in conjunction with the control 

system, generates drive-pulses, which 

operates the IGBT switching devices to 

sequentially provide pulses to each motor. 

Figure: 01. 


Application: 


SEQUENCED PULSE WIDTH MODULATION 

METHOD AND APPARATUS FOR CONTROLLING 

AND POWIRING A PLURALITY OF DIRECT 

CURRENT MOTORS. 


RAIL POWER TECHNOLOGIES 

CORP 


202-50 FELL AVENUE, 

NORTH VANCOUVER, 

BRITISH COLUMBIA V7P 3S2, 

CANDA. 


01. DONNELLY FRANK 

WEGENER 

02. IWAN BRAIN GULAYETS 






533/MUMNP/2004 

PCT/FI03/00259 

Date: 07/04/2003 


Application: 

(54) Title of the invention: METHOD FOR THE RECOVERY OF GOLD. 

(51) International classification: C 22 B 3/20 (71) 


(31) Document No.: 20020780 

(32) Date : 23/04/2002 

(33) Name of convention country : FINLAND 

(66) Filed U/s. 5(2) : NO 






Figure: 


OUTOKUMPU OYJ. 



RIIHITONTUNITE 7, 

FIN-02200 ESPOO, FINLAND, 

AFINNISH PUBLIC LIMTED 

COMPANY. 


01. HAMALAINEN MATTI 

02. HYVARINEN OLLI 






534/MUMNP/2004 

PCT/RU00/00298 

Date: 17/07/2000 

(54) Title of the invention: SPRINKLERS. 

(51) International classification: A 62 C 31/02 (71) 


(31) Document No.: 2000107338 

(32) Date : 28/03/2000 

(33) Name of convention 

country : RUSSIAN FEDERATION 

(66) Filed U/s. 5(2) : NO 




No.: IN/PCT/2002,01270/MUM 



Application: 

(72) 

(57) Abstract: The sprinkler includes the following structural 

members: a body (1) with a channel for liquid supply, a 

thermally responsive unit with a valve (4) closing the sprinkler 

outlet, and a thermally responsive unit attachment. In the first 

alternative embodiment a sprinkler channel is formed by a 

segment (10) of a cylindrical configuration connected with a 

segment (11) made as a conical diffuser. To generate a fine 

uniform gas-and-drop stream of a high kinetic energy and 

space-uniform distribution the cylindrical segment (10) length 

exceeds the channel diameter at this segment. The segment 

length in the form of conical diffuser exceeds the channel 

diameter at the cylindrical segment (10). In the second 

alternative embodiment the sprinkler has two coaxial liquid 

supply channels. The length of the axial cylindrical channel 

exceeds its diameter. The second annular channel is coaxial to 

the first channel and fitted with helical guide components. 

Figure: 01. 



OBSCHESTVO S 

OGRANICHENNOI 

OTVETSTVENNOSTJU 

“UNIPAT”. 


GSP VOLOKOLAMSKOE 

SHOSSE, 4-2-237 MOSCOW 

125871, RUSSIAN FEDERATION. 


01. DUSHKIN ANDREL 

LEONIDOVICH 

02. KARPYSHEV ALEXANDR 

VIDIMIROVICH 







536/MUMNP/2004 

PCT/EP2003/004653 

Date: 03/05 /2003 

(51) International classification: A 61 K 45/06 (71) 


(31) Document No.: 02010305.7 

(32) Date : 07/05/2002 

(33) Name of convention country : EPO 

(66) Filed U/s. 5(2) : YES (72) 







Application: 

28/09/2004 

NEW COMBINATION OF REVERSIBLE PROTON 

PUMP INHIBITORS AND AIRAWAY THER APEUTICS 

FOR TREATING AIRWAY DISORDERS. 


ALTANA PHARMA AG. 


D-78467 KONSTANZ, 

GERMANY. 


01. HANAUER GUIDO 

02. KROMER WOLFGANG 

03. POSTIUS STEFAN 

04. SIMON WOLFGANG- 

ALEXANDER 

The invention relates to the combination of reversible proton pump inhibitors and airway 

therapeutics for the treatment of airway disorders. 

Figure: NIL 







537/MUMNP/2004 

PCT/GB02/02964 

Date:27/06/2002 

(51) International classification: C 07 C 253/16 (71) 


(31) Document No.: 0116212.2 

(32) Date : 03/07/2001 


BRITAIN 

(66) Filed U/s. 5(2) : NO 







Application: 

28/09/2004 

PROCESS FOR THE PREPARATION OF NITRILE 

COMPOUNDS. 

(72) 


PHOENX CHEMICALS LIMITED. 


34 THURSBY ROAD, 

CROFT BUSINESS PARK, 

BROMBOROUGH, WIRRAL, 

CH623PW, 

GREAT BRITAIN. 


01. BLACKER ANDREW JOHN 

02. HOUSON LAN NICHOLAS 

03. WIFFEN JONATHAN 

WILLIAM 

A process is provided for the preparation of a compound of Formula (1) wherein: R is H, 

optionally substituted acyl, optionally substituted alkyl, optionally substituted aryl or 

optionally substituted heteroaryl: R and R each independently are H or a hydroxy 

protecting group; comprising the steps: (a) reacting a compound of Formula (2) in a solvent in 

the presence of a base with a compound of formula RSO2X to give a compound of 

Formula (3); wherein: R is an optionally substituted alkyl, optionally substituted aryl or 

optionally substituted heteroaryl group; and X is halogen: and (b) reacting the compound of 

Formula (3) with a cyanide source in the presence of a phase transfer catalyst. 

Figure: NIL 







538/MUMNP/2004 

PCT/GB03/02192 

Date: 21/05/2003 

(51) International classification: C 07 C 67/31 (71) 


(31) Document No.: 0211716.6 

(32) Date : 22/05/2002 


BRITAIN 

(66) Filed U/s. 5(2) : NO 







Application: 

CONTINUOUS PROCESS FOR THE 

ENANTIOSELECTIVE CATALYTIC 

HYDROGENATION OF BETA-KETOESTERS. 

(72) 


28/09/2004 

PHOENX CHEMICALS LIMITED. 


34 THURSBY ROAD, 

CROFT BUSINESS PARK, 

BROMBOROUGH, WIRRAL, 

CH623PW, 

GREAT BRITAIN. 


01. PROCTOR LEE DAVID 

02. WARR ANTONY JOHN 

The present invention relates to a continuous process for the enantioselective catalytic hydrogenation of B- 

ketoesters comprising providing a catalytic hydrogenation zone and maintaining it under condition of 

temperature and pressure effective for the catalytic hydrogenation of B- ketoesters; continuously supplying 

to the catalytic hydrogenation zone a substrate comprising B- ketoesters to be hydrogenation a catalytic 

effective for the enantioselective hydrogenation of B- ketoesters and hydrogen; contacting the substrate, the 

catalytic and the hydrogen in the hydrogenation zone for a residence time effective for at least partial 

enantioselective catalytic hydrogenation of B- ketoesters; (d) continuously withdrawing from the 

hydrogenation zone a reaction product mixture comprising enantioselectively hydrogenation of B- 

ketoesters, unreacted B- ketoesters, catalytic and hydrogenation; (e) supplying the reaction product mixture 

to a separation zone and separating at least some of the enantioselectively hydrogenation of B- ketoesters 

from the reaction product mixture; (f) withdrawing separted enantioselectively hydrogenation of B- 

ketoesters as product; and (g)optionally supplying at least part of the remaining from the separation zone to 

the hydrogenation zone. 

Figure: NIL 







539/MUMNP/2004 

PCT/GB00/02044 

Date: 26/05/2000 


Application: 

PROCESS FOR PREPARING GRANULAR 

DETERGENT COMPOSITIONS. 



(31) Document No.: 9913544.4 

(32) Date : 10/06/1999 


KINGDOME 

(66) Filed U/s. 5(2) : NO 




Application No.: IN/PCT/2001/01550/MUM 




29/09/2004 








01. BAKKER VERA JOHANNA 

02. KAESS ANDRE 

03. KLAVER MARCO 

A process for the preparation of medium to low bulk density granular detergent composition in 

which a liquid binder is contacted with a solid starting material in high speed mixer and the 

resulting mixture treated in a medium or low speed mixer and finally in a gas fluidisation 

granulator where more liquid binder is added. 

Figure: NIL 







541/MUMNP/2004 

PCT/EP99/08319 

Date: 21/10/1999 



(31) Document No.: 60/105865 

(32) Date : 27/10/1998 


(66) Filed U/s. 5(2) : NO 




Application No.: IN/PCT/2001/00420/MUM 



Application: 

WRINKLE REDUCTION LAUNDRY PRODUCT 

COMPOSITION. 


29/09/2004 








01. MURPHY DENNIS STEPHEN 

02. FOX DANIEL JOSEPH 

(57) Abstract: The present application relates to the inclusion of one or more wrinkle reducing 

ingredients in a laundry detergent product. The benefits are delivered to the laundered item 

during the cleaning step and, therefore, reduces the need for further wrinkle reducing steps when 

the items are taken from the dryer or after hang drying. 

Figure: NIL 






542/MUMNP/2004 

PCT/GB03/00810 

Date: 26/02/2003 


Application: 

(54) Title of the invention: AMORPHOUS CITALOPRAM. 



(31) Document No.: 0204680.3 

(32) Date : 27/02/2002 


BRITAIN 

(66) Filed U/s. 5(2) : NO 






Citalopram base is purified and isolated by chromatography. 

Figure: NIL 


CIPLA LIMTED. 

30/09/2004 




MUMBAI 400 008, 

INDIA. 



02. N KANKAN RAJENDRA 

03. R RAO DHARMARAJ 






543/MUMNP/2004 

PCT/GB03/00816 

Date: 26/02/2003 


Application: 

(54) Title of the invention: AMORPHOUS CITALOPRAM SALTS. 



(31) Document No.: 0204683.7 

(32) Date : 27/02/2002 


BRITAIN 

(66) Filed U/s. 5(2) : NO 







CIPLA LIMTED. 

30/09/2004 




MUMBAI 400 008, 

INDIA. 



02. N KANKAN RAJENDRA 

03. R RAO DHARMARAJ 

A morphous pharmaceutically acceptable salts of citalopram are made by spray drying, lyophilisation or 

evaporation of solution. 

Figure: NIL 






544/MUMNP/2004 

PCT/EP03/03322 

Date: 28/03 /2003 


Application: 

(54) Title of the invention: FABRIC CARE COMPOSITION 



(31) Document No.: 0207742.8 

(32) Date : 03/04/2002 


BRITAIN 

(66) Filed U/s. 5(2) : NO 






(72) 


30/09/2004 





RECLAMATION, 




01. CARSWELL ROBERT JOHN 

02. COOPER JAMES BERNARD 

03. KHOSHDEL EZATT 

04. REID EUAN STUART 

05. RUTHERFORD KEITH 

LESLIE 

This invention relates to a fabric care composition comprising a theremoplastic elastomer and a 

textile compatible carrier, a method of treating fabric with such a composition as part of a laundering 

process and the use of a theremoplastic elastomer or a composition comprising a theremoplastic 

elastomer to improve the crease recovery properties and/ or elasticity and/or shape retention of a 

fabric. 

Figure: NIL 






545/MUMNP/2004 

PCT/EP03/03321 

Date: 28/03 /2003 


Application: 

(54) Title of the invention: FABRIC CARE COMPOSITION. 

(51) International classification: D 06 M 13/192 (71) 


(31) Document No.: 0207744.4 

(32) Date : 03/04/2002 


BRITAIN 

(66) Filed U/s. 5(2) : NO 






(72) 


30/09/2004 





RECLAMATION, 




01. CARSWELL ROBERT JOHN 

02. COOPER JAMES BERNARD 

This invention relates to a fabric care composition comprising a polycarboxylic acid or a catalyst and 

a theremoplastic elastomer a method of treating fabric with such a composition and the use of such a 

composition to increase the tensile strength (especially the tear strength) of a fabric to reduce 

creasing and/or wrinking of a fabric and/or to improve the elasticity and/or shape retention of a fabric. 

Figure: NIL 







546/MUMNP/2004 

PCT/EP00/02438 

Date: 20/03/2000 



(31) Document No.: 09/286041 

(32) Date : 05/04/1999 


(66) Filed U/s. 5(2) : NO 






Application: 

LIQUID COMPOSITIONS COMPRISING SKIN 

BENEFIT AGENT. 

(72) 


30/09/2004 





RECLAMATION, 





(57) Abstract: A stable aqueous liquid comprising a surfactant, a dispersed cationic polymer 

particle and a small particle benefit agent. The dispersed polymer interacts with the benefit 

agent, without need of an additional structurant to stabilize particles in solution. Further, 

upon dilution, enhanced cationic deposition is achieved. 

Figure: NIL 






577/MUMNP/2004 

PCT/AU03/00506 

Date: 30/04/2003 


Application: 

(54) Title of the invention: DILUTION APPARATUS FOR A THICKENER. 

(51) International classification: B 01 D 2/24 (71) 


(31) Document No.: PS 2177 

(32) Date : 07/05/2002 


(66) Filed U/s. 5(2) : NO 






(72) 

The invention provides an axial flow pump (1) for accurately 

injecting supernatant liquid (2) from adjacent the liquid 

surface (3) of a thickening tank (not shown) to dilute liquid in 

a feedwell (4). The pump (1) includes a cup shaped receiving 

vessel (5) submerged in the supernatant liquid. The pump 

also includes a submerged impeller (6) mounted on a 

rotatable shaft (7) for drawing liquid from the vessel (5) and 

injecting it into the feedwell (4). The shaft (7) is driven by a 

motor and associated gearbox (not shown). The pump is 

responsive to system parameters for adjusting the flow rate of 

the supernatant liquid. 


OUTOKUMPU OYJ. 

15/10/2004 


RIIHITONTUNITE 7, 

FIN-02200 ESPOO, FINLAND, 

AFINNISH PUBLIC LIMTED 

COMPANY. 


01. TAYLOR DAVID JOHN 

BUCHANAN 

02. BELKE JEFFREY VICTOR 

Figure: 01. 





(21) Application No.: 580/MUMNP/20004 

PCT/EP01/05628 

(54) Title of the invention: DETERGENT COMPOSITION. 



(31) Document No: 00304752.9 

(32) Date: 05.06.2000 

(33) Name of convention country: EUROPE 

(66) Filed U/s. 5(2): NO. 

(61) Patent of addition to application No.: 

IN/PCT/2002/01730/MUM 

(62) Filed on: 04.12.2002 


(64) Filed on: N.A.S 

A (22) Date of filing of Application: 18/10/2004 

(72) 


HINDUSTAN LEVER LTD 




MUMBAI-400020 


1) DOWDING MICHAEL K. 

2) FINCH TIMOTHY D. 

(57) Abstract: Disclosed is a non-bleaching laundry direct application detergent product providing 

improved maintenance and/or restoration of colour fidelity during the wash, which product is 

obtainable by extrusion and which comprises surfactant, builder, optionally other non-bleach 

detergent ingredients, and from 0.01 to 5.0 wt% of a compound of the formula (I) wherein Y is H 

or OH and X is H or a solubilising cation. 

Figure: NIL. 






(PCT/SG02/00085) 


(54) Title of the invention: A SYSTEM FOR HANDLING CONTAINERS. 

(51) International classification: B66C 1/66 (71) 


(31) Document No: NIL 

(32) Date: NIL 

(33) Name of convention country: NIL 

(66) Filed U/s. 5(2): NO. (72) 






A system (1) for handling containers, the system (1) 

comprising: a) a mounting frame (3); b) a rotation 

device (4) attached to the mounting frame (3); c) a 

spreader 5 having a main axis and being supported by 

the rotation device (4), the rotation device (4) being 

operative to rotate the spreader (5) relative to the 

mounting frame (3); and d) two extension devices (30, 

31), each extension device (30, 31) having a 

longitudinal axis and adapted for connection to a 

container (2) a having a length direction parallel to the 

longitudinal axis; the spreader (5) including inner 

pickup elements (9a, 9b, 10a, 10b) and outer pickup 

elements (33a, 33b, 34a, 34b) for releasably connecting 

the spreader to the extension devices (30, 31) with the 

extension devices (30, 31) side-by-side and the main 

axis of the spreader (5) transverse to the longitudinal 

axis of both the extension devices (30, 31). 


NATSTEEL ENGINEERING P 

LTD 


26 TANJONG KLING, 

SINGAPORE 628051 


LIM, ENG, GUAN 

Figure:1 






(PCT/EP03/03353) 


(54) Title of the invention: COMBINED DNA/ PROTEIN VACCINE COMPOSITIONS. 

(51) International classification: A61K 39/00 (71) 


(31) Document No: 02076276.1 

03075383.4 

(32) Date: 28.03/2002 

10.02.2003. 

(33) Name of convention country: EP 

(66) Filed U/s. 5(2): NO. (72) 






BRENTAG BIOSECTOR A/S 


ELSENBAKKEN 23, DK-3600 

FREDERIKSSUND, 

DENMARK 


1) REIMANN HANSJORG 

2) SCHIRMBECK REINHOLD ALOI 

3) LINDBLAD 

(57) Abstract: The present invention relates to a novel, combined DNA/Protein antigen vaccine 

composition comprising nucleic acid molecules and a mineral-based, negatively charged adjuvant, 

so as to enhance the immungenicity of the DNA vaccine efficiently enhancing not only plasmid 

DNA vaccines but also providing a novel strategy for immunogenic, , multivalent combined 

protein/DNA vaccine delivery. Preferred adjuvants are aluminium or calcium salts, in particular 

aluminium phosphate. 

Figure: NIL 






(PCT/IL03/00240) 


(54) Title of the invention: PHARMACEUTICAL FORMULATION COMPRISING MELATONIN 



(31) Document No: 149377 

(32) Date: 08.04.2002 

(33) Name of convention country: ISRAEL 

(66) Filed U/s. 5(2): NO. 






NEURIM PHARMACEUTICA 

(1991) 

LTD 


8 HANECHOSHET STREET, 

69710 TAL AVIV, 

ISRAEL. 


ZISAPEL, NAVA 

(57) Abstract: Short-term potentiation of non-barbiturate and non-benzodiazepine hypnotics is 

effected by use of melatonin. 

Figure: NIL 






(PCT/US03/12126) 


(54) Title of the invention: ROBUST AND INVARIANT AUDIO PATTERN MATCHING. 

(51) International classification: G10L 21/00 (71) 


(31) Document No: 60/376,055 

(32) Date: 25.04.2002 

(33) Name of convention country: US 

(66) Filed U/s. 5(2): NO. 





(57) Abstract: The present invention provides an 

innovative technique for rapidly and accurately 

determining whether two audio samples match, as 

well as being immune to various kinds of 

transformations, such as playback speed variation. 

The relationship between the two audio samples is 

characterized by first matching certain fingerprint 

objects derived from the respective samples. A set 

(230) of fingerprint objects (231, 232), each 

occurring at a particular location (242), is generated 

for each audio sample (210). Each location is 

determined in dependence upon the content of 

respective audio sample (210) and each fingerprint 

object (232) characterizes one or more local 

features (222) at or near the respective particular 

location (242). A relative value is next determined 

for each pair of matched fingerprint objects. A 

histogram of the relative values is then generated. If 

a statistically significant peak is found, the two 

audio samples can be characterized as substantially 

matching. 

Figure:1 


SHAZAM ENTERTAINMEN 

LTD 


C/O IDG VENTURES EUROPES, 2 

CAVENDISH SQUARE, 

LONDON W1G OPD, 



1) WANG, AVERY LI-CHUN 

2) CULBERT, DANIEL 






( PCT/EP03/04514)_ 

(54) 


Title of the invention: EPOXY MODIFIED ORGANOPOLYSILOXANE RESIN BASED 

COMPOSITIONS USEFUL FOR PROTECTIVE COATINGS 

(51) International classification: C08L 83/04 (71) 


(31) Document No : 02447080.9 

(32) Date: 03.05.2002 


(66) Filed U/s. 5(2): NO. 






SIGMAKALON SERVICES B.V 


AMSTERDAMSEWEG 14, 

NL-1422 AD UITHOORN, 

NETHERLANDS. 


1) KLAASSENS, LARS, IVAR 

2) DE JONG, JAN 

3) VAN DER POEL, HENK 

(57) Abstract: The present invention relates to an epoxy modified polysiloxane composition 

obtainable by combining the following ingredients : -a polysiloxane of formula (1), wherein each 

R is independently selected from the group comprising hydroxy, alkyl, aryl and alkoxy 

radicals having up six carbon atmos, each R is independently selected from the group 

comprising hydrogen, alkyl and aryl radicals having up to six carbon atmos and, wherein n is 

selected so that the molecular weight for the polysiloxane is in the range of from about 400 to 

10,000; with formula (1) –an epoxy resin having more than one 1,2-epoxy groups per molecule 

with an epoxy equivalent weight in the range of from 100 to about 5,000; and –an amino hardener 

component having active hydrogens able to react with epoxy groups in the epoxy resin to form 

polymers containing hydroxyl groups, which are able to react with the silanol groups of 

hydrolyzed polysiloxane to form a polymer network , wherein the epoxy chain polymers and 

polysiloxane polymers polymerize to form a cured epoxy modified polysiloxane polymers 

composition 






(PCT/RU02/00101) 


(54) Title of the invention: METHODS AND SYSTEMS FOR DIGITAL DATA TRANSMISSION. 

(51) International classification: (71) 


(31) Document No 

(32) Date: N.A. 

(33) Name of convention country: RUSSIAN 

FEDARATION 

(66) Filed U/s. 5(2): NO. 


(62) Filed on: (72) 


(64) Filed on: 


1) DOUNAEV, IGOR BORISOVICH 

2) LETOUNOV, LEONID ALEXEEVIC 


UL. GOGOLYA, 14a-48, KHIMKI, 

MOSKOVSKAYA OBL. 141400 

RUSSIAN FEDERATION. 

MZHK "SOLNECHNY", 2-105, 

GOMEL, 246050, BELARUS 


1) DOUNAEV IGOR BORISOVICH 

2) LETOUNOV LEONID ALEXEEVICH 

(57) Abstract: The inventive methods and systems for digital data transmission using a 

communication path which comprises analog communication lines and a pulse-code modulation 

channel (PCM). Said method and systems make it possible to increase a data transmission rate 

through the entire communication path in such a way that it is equal to the data transmission rate of 

the PCM channel irrespective of the quality of used analog communication lines. The spectrum of 

a signal transmitted by an analog transmission line is selected such that the data transmission line 

is equal to the data transmission rate of the PCM channel, and the number of dataq quantisation 

levels transmitted by the analog transmission line is as low as possible for said analog 

communication line. In order to convert an analog signal into an PCM channel signal, the analogsignal 

frequency is decreased proportionally the ratio between the number of data quantisation 

levels transmitted by a PCM channel and the number of data quantisation levels by the analog 

communication line. 






(PCT/EP03/03025) 


(54) Title of the invention: ARCH SYSTEMS. 

(51) International classification: E02D 29/05 (71) Name of the Applicant: 


(31) Document No: 10/02,921 

10/131,526 

10,338,906 

(32) Date: 22.03.2002 

25.04.2002 

09.01.2003 

(33) Name of convention country: NIL (72) 

(66) Filed U/s. 5(2): NO. 






An earth overfilled arched structure (10) includes a 

shallow arch (12) spanning a clear space. The sides of 

the clear space are formed by curved or straight walls. 

Solidified zones of earth material against the springs of 

the arch and/or behind the walls form foundation blocks 

which are in intimate contact via arch footings with the 

springs of the arch and/or with the upper part of the 

sidewalls in such a way that the arched structure 

delivers most or all of its support forces into the 

foundation blocks. Also, an overfilled arch bridge 

system includes a composite arch which has a precast 

layer and a cast-in-place layer. The system further 

includes means for reducing bending moments within 

the overfilled arch. The means include customizing the 

arch end geometry and prestressing the arch prior to or 

during loading. Precast arch elements which are formed 

and shipped in a use orientation. The precast arch 

Figure: 1 

BEBO ARCH INTERNATIONA 

AG 


CULMANNSTRASSE 56, CH-8006 

ZURICH, SWITZERLAND 


HEIERLI WERNER 


elements can include arch footings and the system can 

include a plurality of precast arch elements. The arch 

elements can also be prestressed. 





(PCT/EP03/04240) 

A (22) Date of filing of Application 

(54) Title of the invention: ZINC CITRATE BEADS IN ORAL COMPOSITIONS. 



(31) Document No: 10/132,046 

(32) Date: 25.04.2002 


(66) Filed U/s. 5(2): NO. 





(72) 






MUMBAI-400020 


1) RYLES, CHIRISTINE WATSON 

2) WILLIAMS DAVID ROBERT 

3) ZIEMKIEWICZ ALEXANDER 

GEORAGE 

4) URBAEZ JESUS ANTONIO 

(57) Abstract: An oral product, particularly for anti-tartar use, is provided which includes from 

about 0.001 to about 20% of beads which include zinc salt, the zinc salt having a weight average 

particle size ranging from 0.01 to 5mm, and a dental base. 






(PCT/EP03/03465) 


(54) Title of the invention: PERSONAL CARE ARTICLE WITH DISTINCT ACTIVE ZONE 



(31) Document No: 10/134.207 

(32) Date: 26.04.2002 


(66) Filed U/s. 5(2): NO. 






HINDUSTAN LEVER LTD, 


HINDUSTAN LEVER HOUSE, 165/166 


MUMBAI-400020 


1) GOTT ROBERT EDWARD 

2) PADLO EWA URSZULA 

3) SLAVTCHEFF CRAIG STEPHEN 

(57) Abstract: A disposable, single-use, personal care article is disclosed having an active zone, 

an adjacent non-active zone, and interface therebetween; a benefit releasably associated with the 

active zone; a carrier solvent and optionally a visual indicator associated with the active zone. In 

one embodiment, the benefit agent, the carrier solvent, and a dye indicator are combined and 

applied as stripes on the article. The strips will not substantially bleed into the adjacent non-active 

zone and will disappear during use of the article indicating that the benefit has been transferred to 

the skin or hair of the water. 

Figure: NIL 






(PCT/EP03/04513) 


(54) 

Title of the invention: AMINO-FUNCTIONAL POLYSILOXANES AND THEIR USE IN 

COATINGS. 

(51) International classification: (71) Name of the Applicant: 


SIGMAKALON SERVICES B.V 

(31) Document No: 02447079.1 

(32) Date: 03.05.2002 


(66) Filed U/s. 5(2): NO. 





(72) 


AMSTERDAMSEWEG 14, 

NL- 1422 AD UITHOORN, 

NETHERLANDS 


1) KLAASSENS LARS IVAR 

2) DE JONG JAN 

3) VAN DER POEL 

4) SLINGENEIJER DE GOESWIN 

CHRISTOPHE 

5) MILL SIBEL 

(57) Abstract: The present invention relates to an amino-functional polysiloxane of formula 

(1)R>2-0-[-SIR>1352< (1) WHERIN EACH R>1< is 

independently selected from the group comprising alky1 and ary1 radicals, each R>23< is a bivalent radical or –O-R>35< is hydroxy or alkoxy, and R>5< is selected 

from the group comprising hydrogen, aminoalkyl, aminoalkenyl, aminoaryl, aminocycloalkyl 

radical, optionally substituted by alkyl, aryl, cyaloalkyl, halogen, hydroxy, alkoxy, thinoalkyl, 

amino, amino derivatives, amido, amidoxy, nitro, cyano, keto, acyl derivatives, acyloxy 

derivatives, carboxy, ester, ether, esteroxy, heterocycle, alkenyl or alkynyl and wherein 0 to 90% 

of –O-R>35< is hydroxy or alkoxy. The present invention further relates to an epoxypolysiloxane 

composition obtainable by combining the following ingredients : (a) a polysiloxane 

of formula (4), wherein each R>1’< is independently selected from the group comprising hydroxy, 

alkyl and alkoxy radicals having up to six carbon atoms, each R>2< is independently selected from 

the group comprising hydrogen, alkyl and aryl radicals having up to six carbon atoms and, wherein 

n is selected so that the molecular weight for the polysiloxane is in the range of from about 400 to 

10,000, with R>21’2< (4) (b) an epoxy resin having more than 

one 1,2-epoxy groups per molecule with an epoxy equivalent weight in the range of from 100 to 

about 5,000; and (c) an aminopolysiloxane hardener component or an amino-functional 

polysiloxane hardener component of resin to form epoxy polymers, and able to react with the 

polysiloxane polymers polymerize to form a cured epoxy –polysiloxane polymers composition. 

Figure: NIL 






(PCT/CN03/00290) 

(54) 


Title of the invention: AN INJECTION MADE FROM LXERIS SONCHIFOLIA HANCE FO 

TREATMENT OF CARDIO-CEREBRAL VASCULAR DISEASES AND FUNDS DISEASES 

AND METHOD OF PRODUCING THEROF 

(51) International classification: A6K 35/78, 9/19 (71) 


(31) Document No: 02109532.9 

(32) Date: 23.04.2002 

(33) Name of convention country: CHINA 

(66) Filed U/s. 5(2): NO. 





(72) 


MAOXIANG WANG A CHINE 

NATIONAL 


1# 2-B 008-6 ROOM, 

WAIHUAN NORTH ROAD, TLANJIN 

AERO-PORT GOODS PROCESS ARE 

TIANJIN 3000456, P.R. CHINA 


RUIXLANG ZHANG 

(57) Abstract: The invention discloses an injection made from Chinese herb lxeris Sonchifolia 

Hance for treatment of Cardio-cerebral vascular diseases and funds diseases and method of 

producing thereof. The injection is in a form of lyophilized powder in which the rate of flavone to 

adenosine is 5mg; 15ug or 5mg;30u. The flvone and adenosine from lxeris Sonchifolia Hance is 

more stable in the lyophilized powder from than in liquid form for injection so that it is easy to 

control the quality of the product so as to make the medicament safe and effective. It has benefit in 

store. 

Figure: NIL 






(PCT/IB03/01555) 

(54) Title of the invention: FUNCTIONAL FIBER SHEET. 

(51) International classification: C23C 14/00 (71) 


(31) Document No: JP2002-123296 

(32) Date: 25.04.2002. 

(33) Name of convention country: JAPAN 

(66) Filed U/s. 5(2): NO. 


(62) Filed On; N.A. 





KABUSHIKI KAISH 

SUZUTORA 


36 HAMA-CHO, 

GAMAGORI CITY, AICHI, 

JAPAN 443-8623 


1) SUZUKI MASAYUKI 

2) NAKAJIMA EIGO 

3) SUZUKI TOSHIKAZU 

4) SUZUKI TAKAHIRO 

(57) Abstract: In fiber sheet coated with physically vapor-deposited film, make vapor- deposited 

film transparent so color and pattern on the fiber sheet are visible, furthermore, provide electric 

conductivity to vapor-deposited film ,moreover , improve productivity of vapor deposition, further, 

enable selective blocking of infrared and ultraviolet radiation. In fiber sheet comprising synthetic 

fiber, one face or both faces thereof being coated with physically vapor-deposited film comprising 

metallic oxides, aforementioned metallic oxides comprising mixture of ordinary oxides as a main 

component, containing a small amount of oxides having lower valence than the ordinary oxides [as 

a secondary component], low valence oxide content being 0.1-20 wt% of total amount of metallic 

oxides, thickness of aforementioned physically vapor-deposited film being 5-500nm. 

Figure: NIL 



(PCT/IL02/00260) 


(54) 

Title of the invention: APPARATUS AND METHODS FOR HAND MOTION TRACKING 

AND HANDWRITING RECOGNITION. 

(51) International classification: G 06 K 9/22 (71) Name of the Applicant: 


(31) Document No: NIL 

(32) Date: N.A. 

(33) Name of convention country: NIL 

(66) Filed U/s. 5(2): NO. 



(63) Divisional to Application No.: SNIL 



Apparatus and methods for hand motion 

tracking and handwriting recognition 

including a hand-held device including at 

least one accelerometer providing an 

acceleration indicating output, computation 

circuitry receiving the acceleration 

indicating output and providing a velocity 

indicating output, a handwritten character 

recognizer receiving the velocity indicating 

output and providing a multiple character 

recognition output indication, and a hand 

motion tracker receiving the velocity 

indicating output and providing a tracking 

output indication. 

Figure: NIL 

I.C. + TEAHNOLOGIES LTD 


P.O.BOX 939, 

43000 RAANANA, 

ISRAEL 


1. VARDI MICHA 



PCT/GB03/00381 


(54) Title of the invention: COUPLING DEVICE. 

(51) International classification: E04C 5/16 (71) Name of the Applicant: 


(31) Document No: 0209944.8 

0209943.0 

(32) Date: 01/05/2002 

01/05/2002 

(33) Name of convention country: GB 

(66) Filed U/s. 5(2): NO. 






A coupling device for the coupling of 

reinforcing bars, the coupling device 

comprising an elongate tubular body 

configured for receiving reinforcing bars, in 

particular their end portions, at least one 

recessed gripping surface being formed on 

an inner surface of the elongate tubular 

body, the recessed gripping surface 

comprising a plurality of teeth being 

configured to engage the reinforcing bars in 

response to the engagement of the 

reinforcing bars by a plurality of engaging 

bolts being adjustably positioned through 

the elongate tubular body. 

Figure: 2 

ULTIMATE DESIGN SOLUTIONS LTD 

Address of the Applicant:, 

2 OLDWELL CLOSE, 

SHEFFIELD S17 4AW, 

UK 


1) HOPWOOD IAN 






PCT/IB02/00807 

(54) 


Title of the invention: N-PHENPROPYLCYCLOPENTYL-SUBSTITUTED GLUTARAMIDE 

DERIVATIVES AS NEPINHIBITIONS FOR FSAD. 

(51) International classification: C07C 235/82 (71) 


(31) Document No: 0107750.2 

0113112.7 

0120152.4 

(32) Date: 28/03/2001 

30/05/2001 

17/08/2001 

(33) Name of convention country: GB 

(66) Filed U/s. 5(2): NO. (72) 


(62) Filed on: 


704/MUMNP/2003 

(64) Filed on: 16/07/2003 


PFIZER INC. 


235 EAST 42ND STREET, 

NEW YORK 10017, 

UNITED STATES OF AMERICA 


1) STEPHEN CHALLENGER 

2) ANDREW SIMON COOK 

3) ADAM THOMAS GILLMORE 

4) DONALD STUART MIDDLETON 

5) DAVID CAMERON PRYDE 

6) ALAN STOBIE 

(57) Abstract: The invention relates to compounds of formula (I) for treating for example sexual 

dysfunction, wherein R 1 is optionally substituted c1-6alkyl, optionally substituted carbocyclyl, 

optionally substituted hereocylyl, hydrogen, C1-6alkoxy-NR2R 3 or –NR 4 SO2R 5 , X is the linkage – 

(CH2)n -or- (CH2)q-O-wherein Y is attached to the oxygen); wherein one or more hydrogen atoms 

in linkage X may be replaced independently by C1-4alkoxyoxy ; hydroxy (C1-3alkyl); C3- 

7cycloaklyl; hereocycly; or by C1-4alkyl optionally substituted by one or more fluoro or phenyl 

groups; n is 3,4,5,6or 7; and q is 2,3,4,5 or 6; and Y is phenyl or pyridyl, each of which may be 

substituted; or two R s groups on adjacent on carbon atoms together with the interconnecting carbon 

atoms may form a fused optionally substituted 5- or 6- membered carbocyclic or heterocyclyic 

ring. 

Figure: NIL 






PCT/EP03/03789 


(54) Title of the invention: FOOD PRODUCT COMPRISING A PHYTOSTEROL. 

(51) International classification: A23D 7/00 (71) 


(31) Document No: 02076794.3 

(32) Date: 03.05.2002 


(66) Filed U/s. 5(2): NO. 










MUMBAI-400020 


WILLEM ADRIAAN DE GROOT 

(57) Abstract: Shallow frying products comprising from 35 to 90 wt% fat, phytosterols and a 

specific amount of salt and lecithin, and an aqueous phase with a pH of from 4.5 to 6.5 are less 

prone to oxidation of phytosterols and unsaturated fatty acids under frying conditions. 

Figure: NIL 



PCT/JP99/06859 


(54) 

Title of the invention: OPTICAL RECORDING MEDIUM, RECORDING METHOD AND 

APPARATUS FOR OPTICAL RECORDING MEDIUM AND REPRODUCING METHOD 

AND APPARATUS 

(51) International classification: G 11 B 7/007 (71) Name of the Applicant: 


(31) Document No: P10-346439 

P10-370682 

P11-231389 

(32) Date: 07/12/98 

25/12/98 

18/08/99 


(66) Filed U/s. 5(2): NO. (72) 


(62) Filed no: N.A. 


IN/PCT/2000/00246/MUM 

(64) Filed on: 01/08/2000 


Pits formed according to a first set of data to be 

recorded and constituting a track together with lands 

between the pits are deformed according to a second 

set of data so as to effect recording. The first and 

second sets of data are combinedly reproduced, 

thereby realizing audio reproduction of wide 

frequency band. The first set of data can be 

reproduced by a conventional disk reproducing 

device. The reproduction of the first set of data is 

controlled by using the second set of data so as to 

protect the recorded data. 

Figure: NIL 

SONY CORPORATION 


7-35 KITASHINAGAWA 6-CHOME , 

SHINAGAWA-KU, 

TOKYO 141-0001 


SAKO YOICHIRO 



PCT/FR01/00861 


(54) 

Title of the invention: N-(HETEROCYCLYL) BENZENE- OR -PYRIDINE 

SULPHONAMIDES AS ANTITHROMBOTIC AND ANTICOAGULANT AGENTS 

(51) International classification: C07D 401/14 (71) Name of the Applicant: 


(31) Document No: 00/03, 724 

(32) Date: 23.03.2000 

(33) Name of convention country: FR 

(66) Filed U/s. 5(2): NO. (72) 




IN/PCT/2002,01213/MUM 

(64) Filed on: 05/09/2002 

SANOFI-SYNTHELABO 


174, AVENUE DE FRANCE, 

75013 PARIS 


1) JEAN- MICHEL ALTENBURGER 

2) CREMER 

3) LASSALLE 

4) MATROUGUI 

(57) Abstract: The invention concerns compounds of formula (I) wherein W can represent a- 

(CH2)2-,-(CH2)-C=C or –CH2-CH=CH- group; R2 can in particular represent a piperidinyl group, 

a 1,2,3,6-tetrahydropyridinyl group optionally substituted, a hexahydro-1 (H)-azepinyil 

group, a piperazinyl group optionally substituted or a morphinopolinyl group; R3 can represent 

a-COR1 group; A can in particular represent a phenyl group optionally substituted, a heterocycle 

or a cyclopentyl group and B can in particular represent a pyridyl group, an aminopyrazinyl 

group, anaminopyridazinyl group, a pyrimidinyl group optionally substituted by an amino 

group, a piperidinyl group or an aminopyridinyl group optionally substiotuted on the pyridine by 

a (C1-C4) alkyl or (C1-C4) alkoxy group, the amino group capableof being optionally substituted 

by a (C1-C4) alkyl group. The invention also concerns the preparation of said compounds and 

their therapeutic use. 

Figure: 1 






PCT/EP99/05074 


(54) Title of the invention: SUBSTITUTED PYRAZOLE DERIVATIVES AND MEDICAMENTS. 



(31) Document No: 198 34 044.3 

(32) Date: 29/07/98 

(33) Name of convention country: GERMANY 

(66) Filed U/s. 5(2): NO. (72) 




IN/PCT/2001,00084/MUM 

(64) Filed on: 22/01/2001 



BAYER AKTIENGESELLSCHAF 


D-51368 LEVERKUSEN, 

GERMANY 


1) ALEXANDER STRAUB 

2) ACHIM FEURER 

3) CRISTINA ALON SO-ALIJA 

4) JOHANNES-PETER STASCH 

5) ELISABETH PERZBORN 

6) HOACHIM HUTTER 

7) KLAUS DEMBOWSKY 

8) STAHL ELKE 

The present invention concerns novel substituted pyrazole derivatives of general formula (I), 

wherein R 1 ,R 2 ,R 3 and A have the indicated meaning. The invention also relates to a method for the 

production of said derivatives and to their use as medicaments, especially as medicaments for the 

treatment of cardiovascular diseases. 



PCT/FI03/00343 


(54) 

Title of the invention: METHOD FOR REFINING CONCENTRATE CONTAINING 

PRECIOUS METALS. 

(51) International classification: C 22 B 11/02 (71) Name of the Applicant: 


(31) Document No: 2002 0835 

(32) Date: 03/05/2002 

(33) Name of convention country: FINLAND 

(66) Filed U/s. 5(2): NO. 





(57) Abstract: The invention relates to a method for 

refining precious metal concentrate, and according to 

said method, at least the precious metal concentrate 

(9), reaction gas (10), flux (11) and flue dust (12) to 

be treated are fed together into the reaction shaft (3) 

of a suspension smelting furnace (1); in the 

suspension smelting furnace, there are created 

separate phases, matte (8) and slag (7); and the slag 

created in the suspension smelting furnace is 

conducted into an electric furnace (2), so that there is 

created metallicized matte (14) and waste slag (13). 

Thereafter the matte (8) from the suspension smelting 

furnace is conducted to hydrometallurgical treatment 

(15), and the slag conducted into the electric furnace 

is treated together with a reducing agent and possibly 

with a material lowering the melting point or 

improving fluidity, and the obtained metallicized 

matte (14) is conducted either to hydrometallurgical 

treatment (16) or back into the suspension smelting 

furnace in (1). 

Figure: 2 

OUTOKUMPU OYJ 



FIN-02200 ESPOO, 

FINLAND 


1) MAKINEN TUULA 

2) EEROLA MINNA 

3) LAULUMAA JUKKA 

4) KOJO ILKKA 

5) MERIKANTO NILS 






(PCT/EP00/004223) 

(54) Title of the invention: FABRIC SOFTENING COMPOSITIONS. 



(31) Document No: 9911942.2 

9914266.3 

(32) Date: 21.05.1999 

18.06.1999 

(33) Name of convention country: GREAT 

BRITAN 

(66) Filed U/s. 5(2): NO. (72) 




IN/PCT/2001/01432/MUM 

(64) Filed on: 19.11.2001 







MUMBAI-400020 


1) CLARKE DAVID ELLIS 

2) CREUTZ SERGE FIRMIN ALAIN 

3) HENUALT BENOIT 

4) SMALL SAMANTHA 

(57) Abstract: A fabric softening composition comprising: (a) a cationic fabric softening 

compound; (b) an emulsified silicone. In one aspect the viscosity of the silicone before 

emulsification is from 10,000,000cSt, preferably from 30,000cSt to 750,000cSt, more preferably 

from 40,000cST to 4000,000cSt, most preferably 45,000cSt to 250,000cSt, e.g. 45,000cSt to 

200,000cSt and the emulsion is a macro-emulsion. In another aspect, the median silicone droplet 

size in the emulsion is at least 0.2um, preferably at least 0.25um, more preferably also no greater 

than 25um and is emulsified with an emulsifier comprising one or more cationic surfactants. 

Figure: NIL 





(21) Application No.: 611/MUMNP/2004 A (22) Date of filing of Application: 29/10/2004 

(54) Title of the invention: ANTI-MICROBIAL COMPOSITION. 



(31) Document No: 0001129.6 

(32) Date: 18.01.2000 

(33) Name of convention country: UNITED 

KINGDOM 

(66) Filed U/s. 5(2): NO. 




IN/PCT/2002/00973/MUM 

(64) Filed on: 17.07.2002 






MUMBAI-400020. 


1) CLARKSON KATRIN DAGMAR 

2) LANDA ANDREW SJAAK 

3) MAKIN STEPHEN ANTHONY 

4) VOLKER AXEL 

5) COXON ANDREW CHARLES 

(57) Abstract: An anti-microbial composition comprising: (i) AC1 to C4 monohydric alcohol 

carrier fluid, present at a level of at least 25% by weight of the total composition (excluding any 

volatile propellant present; (ii) an iron (iii) chelator having an iron (III) binding constant of 10 23 or 

greater: (iii) a solubility promoter selected from the group consisting of: (a) water,(b) an organic 

amine; (c) a polyhydric alcohol or derivative thereof; (d) a volatile propellant having fluorinecarbon 

or oxygen-carbon bonds; (e) any combination of (a) to (d). The transitional metal chelator 

serves as an active anti-microbial, whist the carrier fluid-solubility promoter mixture enables the 

formation of a stable composition. Preferred compositions are homogeneous solutions. 

Figure: NIL 





(21) Application No.: 612/MUMNP/2004 A Date of filing of Application: 29/10/2004 

(PCT/US01/07809) 

(2 

2) 

(54) Title of the invention: A METHOD FOR A RADIANT WALL BURNER. 

(51) International classification: F 23 D 14/12 (7 

1) 



JOHN ZINK COMPANY L.L.C 

(31) Document No:60/188,807 

60/208,404 

(32) Date: 13.03.2000 

31.05.2000 


(66) Filed U/s. 5(2): NO. 

(61) Patent of addition to application No.: NIL (7 

2) 



IN/PCT/2001/01459/MUM 

(64) Filed on: 21.11.2001 


A low NOx burner nozzle assembly for a radiant wall 

burner includes an elongated hollow burner tube and 

a discharge nozzle. The burner tube defines a conduit 

for supplying a mixture of fuel and air to a radiant 

combustion area. The discharge nozzle is mounted on 

the tube at the downstream end of the conduit and 

adapted for directing the mixture of fuel and air in an 

essentially radial direction. The discharge nozzle 

includes a plurality of flow directing members 

arranged in an array to define there between a 

plurality of passageways which extend in a generally 

radial direction and having different respective flow 

areas. The discharge nozzle also has an end cap to 

prevent axial flow of the primary air/fuel mixture. 

The end cap has an axially extending hole therein, 

and the nozzle assembly includes a staged fuel burner 

nozzle arranged so as to protrude axially through 

such hole. 


11920 EAST APACHE, 

TULSA, OK 74116, 

U.S.A 


JOHN ZINK COMPANY L.L.C 

Figure: 1 


“Publication after 18 Months 

The following Patent Applications have been published under Section 11A (3) of The Patents 

(Amendment) Act, 2005. Any Person interested may file Representation by way of opposition to 

the Controller of Patents at the appropriate office against the grant of the patent in the prescribed 

manner under section 25(1) of the The Patents (Amendment) Act, 2005 read with the rule 55 of 

The Patents (Amendment) Rules, 2005 :” 

__________________________________________________________________ 


(19) INDIA (21) Application No. 415/CAL/95 A 


(54) Title of the invention: LOBAPLATING 

TRIHYDRATE 

(51) International classification: C07F 15/00,A61K 

31/28 

(31) Priority Document No: P 4415263.9 

(32) Priority Date: 15/04/1994 

(33) Name of priority country: GERMANY 

(86) International Application No and Filing Date: NIL 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: ASTA MEDICA 

AKTIENGESELLSCHAFT 

Address of the Applicant: AN DER 

PIKARDIE 10,D-0177 DRESDEN 

GERMANY 


1 ECKHARD GUNTHER 

2. DR. JENS-PETER WULF 

3. PROF. DR. JURGEN ENGEL 

4. DR. BERNHARD KUTSCHER 




Lobaplatin trihydrate constitutes a new and advantageous form of a platinum complex having an anitumor 

effect. 


______________________________________________________________ 




(54) Title of the invention: “ 4-(1H-INDOL-1-YL)-1- 

PIPERIDINYL DERIVATIVES” 

(51) International classification: A61K 31/505.C07D 

47/104 

(31) Priority Document No: 95.200.229.3 

(32) Priority Date: 31/01/1995 

(33) Name of priority country: EPO 





filed on: NIL 



filed on: NIL 


(71) Name of Applicant: JANSEEN 

PHARMACEUTICALS N.V. 


TUNHOUTAEWEG 30,B-2340- 

BEERSE,BELGIUM 


1. JAN VANDENBERK 

2. LUDO EDMOND JOSEPHINE KENNIS 

3. JOSEPHUS CAROLUS MERTENS 




__________________________________________________________________ 





INDAZOLECARBOXAMIDES 

(51) International classification: A61K 31/00,31/16 

(31) Priority Document No: 08/405,119 

(32) Priority Date:16/03/1995 

(33) Name of priority country: USA 





filed on: NIL 



filed on: NIL 


(71) Name of Applicant: ELILILLY AND 

COMPANY 

Address of the Applicant: LILLY 

CORPORATE CENTER,CITY OF 

INDIANAPOLIS,STATE OF INDIANA,USA 


1. JOHN THOMAS CATLOW 

2. MARLENE LOIS COHEN 

3. MICHAEL JOHN MARTINELLI 

4. JOHN MEHNERT SCHAUS 

5. STEVEN PHILLIP SWANSON 

6. DENNIS CHARLES THOMPSON 

7. THOMAS MICHAEL WILSON 




__________________________________________________________________ 




(54) Title of the invention: NOVEL 

PHARMACEUTICALLY ACTIVE, ACETONYL N. N- 

DIETHYLDITHIOCARBAMATES” 

(51) International classification: A61K 31/00,C07C 

155/08 








filed on: NIL 



filed on: NIL 


(71) Name of Applicant: ICI INDIA 

LIMITED AND ICI INDIA RESEARCH & 

TECHNOLOGY CINTRE 

Address of the Applicant: P.O. BOX 9084,34 

CHOWRINGHEE ROAD,CALCUTTA-700 

071,WEST BENGAL INDIA AND THANE 

BELAPUR ROAD,THANE-400 

601,MAHARASHTRA 


1. S.S.R. KUMAR 

2. RANJAN V. SALUNKHE 




_________________________________________________________________ 




(54) Title of the invention: IMMOBILIZED AND 

ACTIVITY-STABILIZED COMPLEXES OF LHRH 

ANTAGONISTS AND PROCESSES FOR THEIR 

PREPARATION 


(31) Priority Document No: 19712718.5 

(32) Priority Date: 26/03/1997 






filed on: NIL 



filed on: NIL 


_ 


INC 


PIKARDIE 10,D-01277 

DRESDEN,GERMANY 


1. PRASANTA BANERJI AND PRATIP 

BANERJI 




________________________________________________________________ 



(22) Date of filing of Application 24/06/1998 (43) Publication Date: 24/06/2005 

(54) Title of the invention: “ASINGLE-PHASE 

CIRCUIT BREAKER FUNCTIONING AS A 

MULTIPHASE CIRCUIT BREAKER” 

(51) International classification: H01H 71/10,71/74 

Priority Document No: 1190/97 

(32) Priority Date: 10/07/1997 

(33) Name of priority country: AUSTRIA 



(71) Name of Applicant: FELTEN & 

GILLEAUME AUSTRIA AG 

Address of the Applicant: A- 

3943,SCHREMS,EUGENIA 1,AUSTRIA 


1. TIBOR POLGAR 


(Amendment) Ordinance,2004 : NO 


__________________________________________________________________ 




(54) Title of the invention: A DEVICE FOR 

CONTROLLING AUTOMATICALLY THE DEPTH OF 

THE VERTICAL AND HORIZONTAL LOOPS 

FORMED IN STEEL WIRE RODS DURING 

ROLLING” 

(51) International classification: B23D 79/00 








filed on: NIL 



filed on: NIL 


(71) Name of Applicant: STEEL 

AUTHORITY FO INDIA LIMITED 

Address of the Applicant: ISPAT 

BHAWAN,LODHI ROAD,NEW DELHI- 

110003 


1. ASHOK KUMAR PAUL 

2. SAURABH DIXIT 

3. GURDIP SINGH SANGAR 

4. SUSHIL KUMAR SABLOK 

5. BIJOY BHOWMIK 

6. SUBRATO SINHA 

7. BRAJENDRA KUMAR SANTRA 

8. SUSHIL CHANDRA KHAN 

9. NIRBHOR NEOGI 

10. GOPAL JIVAN MAHAJAN 

11. SUSHANTA MAJUMDAR 





__________________________________________________________________ 




(54) Title of the invention: “A POSITIVE 

TEMPERATURE COEFFICIENT THERMISTOR” 

(51) International classification: H01G 7/10,7/3 

Priority Document No: 9-293090 

(32) Priority Date: 27/10/1997 

(33) Name of priority country: JAPAN 





filed on: NIL 



filed on: NIL 


(71) Name of Applicant: MURATA 

MANUFACTURING CO,LTD, 

Address of the Applicant: 26-10,TENJIN 2- 

CHOME,NAGAOKAKYO-SHI,KYOTO- 

FU,617-8555,JAPAN 


1. YASUHIRO NABIKA 

2. TAKEO HAGA 




____________________________________________ 




(54) Title of the invention: ALCOHOL-BASED ANTI- 

MICROBIAL COMPOSITIONS WITH COSMETIC 

APPEARANCE” 









filed on: NIL 



filed on: NIL 

(71) Name of Applicant: ETHICON INC 

Address of the Applicant: U.S. ROUTE 22, 

SOMERVILLE NJ08876 USA 


1. HANUMAN J. JAMPANI 

2. JERRY L. NEWMAN 




A rapidly acting antimicrobial alcohol-containing composition and method of using the composition to 

disinfect surfaces, such as the hands is disclosed. 

__________________________________________________________________ 




(54) Title of the invention: SPRAYABLE 

INSECTICIDAL COMPOSITIONS HAVING 

ENHANCED EFFICACY 

(51) International classification: A01N 25/12 


(32) Priority Date: 31/03/1998 






filed on: NIL 



filed on: NIL 


(71) Name of Applicant: AMERICAN 

CYNAMID COMPANY 

Address of the Applicant: FIVE GIRALDA 

FARMS,MADISON,NEW JERSEY 07940- 

0874,USA 


1. JOSEPH KILMER 




__________________________________________________________________ 




(54) Title of the invention: LOBAPLATING 

TRIHYDRATE” 

(51) International classification: C07F 15/00,A61K 

31/28 


(32) Priority Date: 15/04/1994 






filed on: NIL 


Application No: 415/CAL/1995 

filed on: 17/04/1995 





PIKARDIE 10,D-01277 D-01277 DRESDEN 

GERMANY 


1. GUNTHER ECKHARD 

2. WULF JENS-PETER 

3. ENGEL JURGEN 

4. KUTSCHER BERNHARD 



Lobaplatin trihydrate is new and advantageous form of antitumor-active platin complex. 




(54) Title of the invention: USE OF INHIBITORS OF 

PHOSPHODIESTERASE FOR TREATING ALLERGIC 

RHINITIS” 

(51) International classification: A61K 31/415,A61K 

45/00 


(32) Priority Date: 03/07/1997 

(33) Name of priority country:GERMANY 





filed on: NIL 



filed on: 01/07/1998 



ARZNEIMITTELWERK DRESDEN GMBH. 

Address of the Applicant: MEISSNER 

STRASSE 35,D-01445 RADEBEUL 

GERMANY 


1. ENGEL JURGEN 

2. POPPE HILDEGARD 

3. MARX DEGENHARD 

4. HOFGEN NORBART 

5. SZELENYL STEFAN 




_________________________________________________________________ 




(54) Title of the invention: NOVEL N- 

BENZYLINDOLE AND BENZOPYRAZOLE 

DERIVATIVES WITH ANTI-ASTHMATIC,ANTI- 

ALLERGIC,ANTI-INFLAMATORY AND IMMUNE 

MODULATING EFFECT” 

(51) International classification: C07D 209/22,A61K 

31/44 

(31) Priority Document No: P4427393.2 







filed on: NIL 



filed on: 24/07/1995 





PIKARDIE 10,D-01277 

DRESDEN,GERMANY 


1. LEBAUT GUILLAUME 

2. FOUCHARD FABIENNE 

3. KUTSCHER BERNHARD 

4. EMIG PETER 

5. FLEISCHHAUER LLONA 



__________________________________________________________________ 




(54) Title of the invention: “HUMANIZED ANTI-FAS 

ANTIBODY” 

(51) International classification: 

Priority Document No: HEI-10-276881 

(32) Priority Date: 30/09/1998 






filed on: NIL 



filed on: NIL 

(71) Name of Applicant: SANKYO 

COMPANY LIMITED 

Address of the Applicant: 5-1,NIHONBASHI 

HONCHO 3-CHOME,CHUO-KU,TOKYO 

103-8426,JAPAN 


1. SERIZAWA NOBUFUSA 

2. HARUYAMA HIDEYUKI 

3. NAKAHARA KAORI. 

4. TAMAKI IKUKO, 

5. TAKAHASHI TOHRU 




Anti-Fas antibodies are cross-relative with mouse and human Fas and are useful in the treatment of 

conditions attributable to abnormalities in the Fas/Fas ligand system. 


__________________________________________________________________ 


(19) INDIA (21) Application No.827/CAL/1999 A 

(22) Date of filing of Application 06/10/99 (43) Publication Date: 24/06/2005 

(54) Title of the invention: “COMPOUNDS FOR THE 

TREATMENT OF BIABETIC AND AGING-RELATED 

VASCULAR COMPLICATIONS” 

(51) International classification: A61K 31/44,C07D 

213/46 






( 


____ 

(71) Name of Applicant: TORRENT 

PHARMACEUTICALS LTD. 


CENTRAL PLZA 1 ST FLOOR, ROOM 106,2/6,SARAT 

BOSE ROAD,CALSUTTA-700 020,WEST BENGAL 

INDIA 


1. SANKARANARAYANAN ALANGUDI, 


Ordinance,2004 : YES 


______________________________________________________________ 




(54) Title of the invention: “ ANTIMICROBIAL ACID 

CLEANER FOR USE ON ORGANIC OR FOOD SOIL” 

(51) International classification: C11D 1/62,7/08 

(31) Priority Document No: 09/275,065 

(32) Priority Date: 23/03/1999 






filed on: NIL 



filed on: NIL 


(71) Name of Applicant: ECOLAB INC 

Address of the Applicant: ECOLAB 

CENTER,ST. PAUL MINNESOTA 

55102,USA 


1. HERDT BRANDON 

2. HALSRUD DAVID A. 




__________________________________________________________________ 




(54) Title of the invention: “ AN IMPROVED 

PORTABLE DEVICE FOR IN-SITU PREHEATING OF 

DIES IN CLOSED DIE FORGING” 

(51) International classification: B21J 1/06,31/02 








filed on: NIL 



filed on: NIL 



AUTHORITY OF INDIA LIMITED 

Address of the Applicant: RESEARCH & 

DEVELOPMENT CENTREFOR IRON & 

STEEL,DORANDA RANCHI- 

834002,BIHAR 


1. JAIN DINESH KUMAR 

2. JHA SAMIR KUMAR 

3. ROY BASUDEO 




__________________________________________________________________ 


(19) INDIA (21) Application No 359/CAL/2000 A 

(22) Date of filing of Application 22.06.2000 (43) Publication Date: 24/06/2005 

(54) Title of the invention: FOAMING OIL GEL 

COMPOSITIONS 

(51) International classification: A61K 7/00, 7/48, 7/50 


(32) Priority Date: 23.06.1999 

(33) Name of priority country: U.S.A 




Application No: 

filed on: 



filed on: 


JOHNSON & JOHNSON 

CONSUMER COMPANIES 

INC. 


GRANDVIEW ROAD, 

SKILLMAN, NEW JERSEY 

08558, U.S.A 


(1) SANTORA DELORES M. 

(2) HOPKINS JOHN 

(3) MCCULLOCH LAURA J. 





The gelled oil composition containing an emulsifier , a gelling agent, an oil, and a surfactant which, when 

applied to the skin in the presence of water , produces a significant amount of foam. After the composition 

is rinsed from the skin, a non-greasy, oil residue is left thereon 


__________________________________________________________________ 




(54) Title of the invention: SILENCER FOR TWO- 

STRKE ENGNES CONTAINING A CATALYTIC 

DEVICE AND CATALYTIC DEVICE THEREFOR” 

(51) International classification: F01N 3/28,7/18 

(31) Priority Document No: 99 120 742.4 

(32) Priority Date: 20/10/1999 

(33) Name of priority country: EP 





filed on: NIL 



filed on: NIL 


(71) Name of Applicant: DEGUSSA-HULS 


Address of the Applicant: DE-60287 

FRANKFURT MAIN GERMANY 


1. HOHN GEORG SUKUNVIT 

2. BOVONSOMBAT PAKON 

3. SUYOD WICHAI 




__________________________________________________________________ 




(54) Title of the invention: “FLASHLIGHT 

GENERATING CIRCUIT” 

(51) International classification: H05B 41/32,G03B 

15/02,G03B 15/03,G03B 15/05 

Priority Document No: HEI.11-325116 

(32) Priority Date: 16/11/1999 






filed on: NIL 



filed on: NIL 


(71) Name of Applicant: FUJI PHOTO FILM 

CO,LTD. 


210,NAKANUMA,MINAMI-ASHIGARA- 

SHI,KANAGAWA 250-0193,JAPAN 


1. MOTOMURA KATSUMI 

2. JUN-JIN KONG 




__________________________________________________________________ 



(22) Date of filing of Application 30/11/2000 (43) Publication Date: 24/6/2005 

(54) Title of the invention: DEVICE FOR READING 

FROM AND/OR WRITING TO OPTICAL 

RECORDING MEDIA” 

(51) International classification: G11B 7/09 








filed on: NIL 



filed on: NIL 


(71) Name of Applicant: DEUTSCHE 

THOMSON-BRANDT GMBH 

Address of the Applicant: HERMANN- 

SCHWER-STR.3,D-78048 VILLINGEN- 

SCHWENNINGEN,GERMANY 


1. KRAVTCHENKO ALEXANDER 

2. KABUTZ MARTEN 

3. PEYTAVIN BRUNO 




__________________________________________________________________ 


(19) INDIA (21) Application No 693/CAL/2000 A 

(22) Date of filing of Application 19.12.2000 (43) Publication Date: 24/06/2005 

(54) Title of the invention: ADHESIVE BANDAGE 

PAD MODULE AND METHOD FOR MAKING AND 

APPLYING ADHESIVE BANDAGE PADS TO A WEB 

(51) International classification: B32B 31/00 


(32) Priority Date: 23.12.1999 


(86) International Application No and Filing Date: N.A 

(87) International Publication No: N.A 


Application No: N.A 

filed on: 



filed on: 



JOHNSON & JOHNSON 

CONSUMER COMPANIES, 

INC. 


GRANDVIEW ROAD, 

SKILLMAN, NEW JERSEY 

08558, U.S.A 


(1) MUESCH EDWARD 

(2) ADAMS CHARLES LEE 

(3) DAMIANI JOHN 

(4) DESALVO PHIL 





__________________________________________________________________ 




(54) Title of the invention: “AN IMPROVED PROCESS 

FOR RECOVERY OF IRON VALUES FROM IRON 

ORE FINES SUCH AS REJECTS/WASTES OF IRON 

ORE WASHING PLANTS” 

(51) International classification: C21B 15/00 

Priority Document No: 







filed on: NIL 



filed on: NIL 



AUTHORITY OF INDIA LIMITED 

Address of the Applicant: RESEARCH & 

DEVELOPMENT CENTRE FO RIRON & 

STEEL,DORANDA,RANCHI- 

834002,STATE OF BIHAR,INDIA 


1. SRIVASTAVA MAHESH PRASAD 

2. PAN SWAPAN KUMAR 

3. PRASAD NARMADESHWAR 

4. GAIDHANI SURYABHAN BABURAO 




__________________________________________________________________ 



(22) Date of filing of Application 06/02/2001 (43) Publication Date: 24/6/2005 

(54) Title of the invention: A PORTABLE DEVICE FOR 

USE WITH CONVENTIONAL GAS BURNERS TO 

SERVE AS AN OVEN FOR BAKING/COOKING 

PURPOSES 

(51) International classification: F23D 14/06 








filed on: NIL 



filed on: NIL 


(71) Name of Applicant: SINHA 

JYOTIRINDRA PROSAD 

Address of the Applicant: 71,SUSSEX 

ROAD, WAT FORD, HERTS,WD 2-5 HR 

UK 


1. SINHA JYOTIRINDRA PROSAD 




__________________________________________________________________ 




(54) Title of the invention: “CYLINDER HEAD 

WITH TWO-PLANE WATER JACKET” 

(51) International classification: F02F 1/36 


(32) Priority Date: 16/02/2000 






filed on: NIL 



filed on: NIL 


(71) Name of Applicant: DEERE & 

COMPANY 

Address of the Applicant: MOLINE ILLINOIS 

61265 USA 


1 HAUGEN DAVID JAMES 

2. SANDOVAL FERNANDO 




__________________________________________________________________ 




(54) Title of the invention: “PERIPHERAL PUMP” 

(51) International classification: F04D 5/00 

(31) Priority Document No: PD200A000052 

(32) Priority Date: 25/02/2000 

(33) Name of priority country: ITALY 





filed on: NIL 



filed on: NIL 


(71) Name of Applicant: SEA-LAND S.R.L. 

Address of the Applicant: ENRICO MATTEI 

25, 35038 TORREGLIA ITALY 


1 PAOLO BERLOSE 




__________________________________________________________________ 




(54) Title of the invention: “A NOVEL APPARATUS 

FORGENERATING PRODUCER GAS OF HIGHER 

CALORIFIC VALUE” 

(51) International classification: C10J 1/00 

Priority Document No: 







filed on: NIL 



filed on: NIL 


(71) Name of Applicant: PREMENDRA 

MALIAH 

Address of the Applicant: 66 TIVOLI 

COURT,BLOCK-B,10 TH FLOOR,1A 

BALLYGUNGE CIRCULAR ROAD, 

KOLKATA-700 019,WEST BENGAL, 

INDIA 


1. PREMENDRA MALIAH 




__________________________________________________________________ 




(54) Title of the invention: SPINNING MACHINE 

COMPRISING A PLURALITY OF SPINNING 

STATIONS 

(51) International classification: D01H 5/72,5/26,5/00 


(32) Priority Date: 10/05/2000 






filed on: NIL 



filed on: NIL 


(71) Name of Applicant: STAHLECKER 

FRITZ AND STAHLECKER HANS 

Address of the Applicant: JOSEF-NEIDHART 

STRASSE 18,73337 BAD 

UBERKINGEN,GERMANY AND 

EISBRUNNEN STRASSE 37,,73072, 

DONZDORF,GERMANY 


1. STAHLECKER HANS 




__________________________________________________________________ 


(19) INDIA (21) Application No.386/CAL/2001 A 


(54) Title of the invention: SAFETY AIR VEHICLE 

(51) International classification: B60R 21/32 








filed on: NIL 



filed on: NIL 

(71) Name of Applicant: GOUR GOPAL 

PAL 


VILL-PALSA,P.O.-PATNIL,VIA- 

KIRNAHAR,PIN-731302,BIRBHUM,WEST 

BENGAL,INDIA 


1. GOUR GOPAL PAL 


(Amendment) Ordinance,2004 : No 


It is a mechanical type of invention based on the theories of (I) action and reaction (II) inertia of motion and 

inertia of rest. (III) speed of a Mass (IV) of Gravity. 


__________________________________________________________________ 




(54) Title of the invention: “METHOD OF CASTING 

AND CASTING MACHINE” 

(51) International classification: B22C 9/06,9/08 

Priority Document No: 2001-16858 

(32) Priority Date: 25/01/2001 






filed on: NIL 



filed on: NIL 


(71) Name of Applicant: NISSIN KOGYO 

KABUSHIKI KAISHA 

Address of the Applicant: 840,OOAZA 

KOKUBU,UEDA-SHI,NAGANO 386-8505 

JAPAN 


1. BAN KEISUKE 

2. SASAKI YASUHIRO 

3. SUNOHARA AKIRA 

4. OGIWARA KOICHI 

5. NAKATANI SAKUZO 




__________________________________________________________________ 




(54) Title of the invention: “DUAL INK JET PRINT 

CARRIAGE FOR WEB PRINTING” 

(51) International classification: B41J 3/54 


(32) Priority Date: 05/09/2000 






filed on: NIL 



filed on: NIL 


(71) Name of Applicant: HEWLETT- 

PACKARD COMPANY 

Address of the Applicant: 3000 HANOVER 

STREET,PALO ALTO,CALIFORNIA 

94304,USA 


1. GEORGE C. ROSS 

2. LAWRENCE R. PLOTKIN 

3. PAUL R. KROUSES 

4. DAVID M. KWASNY 







(54) Title of the invention: A SYNERGISTIC ALOE 

VERA HAIR NOURISHMENT COMPOSITION” 

(51) International classification: A61K 7/06 








filed on: NIL 



filed on: NIL 


(71) Name of Applicant: DR. MRINAL 

KANTI MAJUM,DAR 

Address of the Applicant: 93/2,GARFA 

MAIN ROAD, JADAVPUR.KOLKATA-700 

075,INDIA 


1. DR. MRINAL KANTI MAJUM,DAR 




__________________________________________________________________ 




(54) Title of the invention: NOVEL PREPARATION OF 

SELECTIVE CYCLOOXYGENASE INHIBITORS” 

(51) International classification: A61K 7/06 








filed on: NIL 



filed on: NIL 


(71) Name of Applicant: PATEL DINESH 

SHANTILAL 

Address of the Applicant: 5, HARISH 

MUKHERJEE ROAD, CALCUTTA-700 

025,P.O. BHOWANIPUR,WEST BENGAL 

INDIA 


1. PATEL DINESH SHANTILAL 

2. PATEL SACHIN DINESH 

3. KURANI SHASHIKANT PRABHUDAS 




__________________________________________________________________ 




(54) Title of the invention: “ RUTAPHOS” 









filed on: NIL 



filed on: NIL 

(71) Name of Applicant: PRASANTA 

BANERJI AND PRATIP BANERJI 

Address of the Applicant: 10/3/1 LALA 

LAJPAT RAI SARANI,KOLKATA-700 

020,WEST BENGAL INDIA 


1PRASANTA BANERJI 

2. PRATIP BANERJI 




Product for regression of tumors which comprises Ruta graveolens 6, Calcarea phosphorica 3X and distilled 

water. 

__________________________________________________________________ 




(54) Title of the invention: “ A HERBAL 

PHARMACEUTICAL PREPARATION FOR THE 

TREATMENT OF LEUCIDERMA 









filed on: NIL 



filed on: NIL 


(71) Name of Applicant: DR. SWAPAN 

KUMAR CHATTERJEE 

Address of the Applicant: 11-76 M.M. GHOSH 

LANE,PATRA MARKET,KRISHNAGAR 741 

101,NADIA 


1. DR. SWAPAN KUMAR CHATTERJEE 



This invention relates to a pharmaceutical preparation for the treatment of leukoderma comprising tyrosine, 

a diluent and optionally methionine and an inorganic salt of zinc. 


__________________________________________________________________ 


(19) INDIA (21) Application No 125/KOL/2003 A 


(54) Title of the invention: AN OPTICAL 

INFORMATION RECORDING MEDIUM 

(51) International classification: G06K 19/00, 21/00 

(31) Priority Document No: 2002-059005 ; 2002-202744; 

2002-322708 

(32) Priority Date: 05.03.2002; 11.07.2002; 06.11.2002 






filed on: 



filed on: 



MITSUBISHI CHEMICAL 

CORPORATION 

Address of the Applicant: 5-2, 

MARUNOUCHI 2-CHOME, 

CHIYODA-KU, TOKYO, 100- 

0005, JAPAN 


(1) MICHIKAZU HORIE 

(2) TAKASHI OHNO 






__________________________________________________________________ 


(19) INDIA (21) Application No. 129/KOL/2003 A 


(54) Title of the invention: “CLAMPING APPARATUS 

WITH A CLAMPING CHUCK AND A WORK PIECE 

CARRIER RELEASABLY CONNECTABLE 

THERETO” 

(51) International classification: B23Q 3/00 

Priority Document No: 2002 0415/02 

(32) Priority Date: 11/03/2002 

(33) Name of priority country: SWITZERLAND 





filed on: NIL 



filed on: NIL 


(71) Name of Applicant: EROWA AG 

Address of the Applicant: WINKELSTRASSE 

8,CH-5734 REINACH SWITZERLAND 


1. FRIES KARL 




__________________________________________________________________ 


(19) INDIA (21) Application No.: 489/KOL/2004 A 

(22) Date of filing of Application: 16.08.2004 (43) Publication Date: 24/06/2005 

(54) Title of the invention: SUCTION SILENCER AND 

COMPRESSOR THEREWITH 

(51) International classification: F01N 3/24 

(31) Priority Document No: P 2003-0056833 

(32) Priority Date: 18.08.2003 

(33) Name of priority country: REPUBLIC OF 

KOREA 





filed on: 



filed on: 


(71) Name of Applicant: LG 

ELECTRONICS INC. 

Address of the Applicant: 20, 

YOIDO-DONG, 

YOUNGDUNGPO-GU, SEOUL, 

REPUBLIC OF KOREA 


(1) JUNG MIN KYU 

(2) PARK DONG WOO 





__________________________________________________________________ 


(19) INDIA (21) Application No. IN/PCT/2000/00409 A 


(54) Title of the invention: METHOD FOR 

PRODUCING ENANTIOMER-FREE N-METHYL-N- 

[(1S)-1-PHENYL-2-(3S)-3- 

HYDROXYPYRROLIDINE-1-YL)ETHYL]-2,2- 

DIPHENYL ACETAMIDE 

(51) International classification: C07D 207/12,A61K 

31/40,C07B 43/06,35/02 


(32) Priority Date: 20/04/1998 

(33) Name of priority country: DE 


PCT/EP99/02574 AND 16/04/1999 

(87) International Publication No: WO 99/54298 A1 



filed on: NIL 


Application No NIL 

filed on: NIL 


(71) Name of Applicant: MERCK PATENT 

GMBH 

Address of the Applicant: FRANKFURTER 

STRASSE 250,D-64293 

DARMSTADT,GERMANY 


1. BATHE ANDREAS 

2. HELFRT BERND 

3. ACKERMANN KARI-AUGUST 

4. GOTTSCHLICH RUDOLF 

5. STEIN INGEBORG 

6. BUDAK JENS 




__________________________________________________________________ 


(19) INDIA (21) Application No. IN/PCT/2001/00067 A 


(54) Title of the invention: “MEDICINAL AEROSOL 

FORMULATIONS” 


(31) Priority Document No: 1633/98 

(32) Priority Date: 04/08/1998 

(33) Name of priority country: CH 


PCT/CH99/00360 AND 02/08/1999 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: JAGO RESEARCH 

AG 


EPTINGERSTRASSE 51 CH-4132 MUTTENZ 

SWITZERLAND 


1 KELLER MANFRED 

2. HERZOG KURT 

3. MULLER-WALZ RUDI 

4. KRAUS HOLGER 



__________________________________________________________________ 


(19) INDIA (21) Application No IN/PCT/2001/00128 A 


(54) Title of the invention: POLYMER COMPLEXES 

OF GLUCURONOGLUCANES 

(51) International classification: C08B 37/00, A61K 

47/36,7/00, 9/02, 9/16, 9/20, C08J 9/00, A61K 6/097, 

C08L 5/00 

(31) Priority Document No: S980594 TO S980599 

(32) Priority Date: ALL 21.07.1998 

(33) Name of priority country: IRELAND 


PCT/IE99/00067 – 21.07.1999 

(87) International Publication No: WO 00/05269 A1 – 

03.02.2000 

: 


ALPENSTOCK HOLDINGS 

LIMITED 


CHURCH PLACE, 

SALLYNOGGIN, COUNTY 

DUBLIN, IRELAND 


(1) SANTAR IVAN 

(2) KISS FRANTISEK 

(3) BRIESTENSKY JIRI 





A biocompatible intermolecular polymer complex comprises an anionic component and a non protein 

cationic component.The anionic component comprises a linear or branched polysaccharide chain wherein at 

least 5% of the basic structural units are glucuronic acid. The cationic component comprises a linear or 

branched natural, semi-synthetic oligomer or polymer 


__________________________________________________________________ 




(54) Title of the invention: “ COMPOSITE 

MATERIAL COATING AND A METHOD FOR 

THE PRODUCTION THEREOF” 

(51) International classification: C23C 30/00 


(32) Priority Date: 24/09/1998 



PCT/DE99/02859 AND 04/09/1998 

(87) International Publication No: WO 00/17416 



filed on: NIL 



filed on: NIL 


(71) Name of Applicant: WIDIA GMBH 

Address of the Applicant: MUNCHENER 

STRASSE 90 D-45145 ESSEN GERMANY 


1. WESTPHAL HARTMUT 

2. SOTTKE VOLKMAR 




__________________________________________________________________ 


(19) INDIA (21) Application No.IN/PCT/2002/00474 A 


(54) Title of the invention: “METHOF FOR THE 

ELECTROCHEMICAL DETECTION OF NUCLEIC 

ACID OLIGOMER HYBRIDS” 

(51) International classification: C07H 21/00,C12Q 1/68 


(32) Priority Date: 23/11/1998 



PCT/EP99/08888 AND 19/11/1999 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: FRIZ BIOCHEM 

GMBH 

Address of the Applicant 

NIBELUNGENSTRASSE 10,D- 

80639,MUNCHEN GERMANY 


1. HARTWICH GERHARD 

2. HELLER ADAM 




__________________________________________________________________ 




(54) Title of the invention: “TEAT DISINFECTANT” 

(51) International classification: A01N 

37/04,37/52,55/02,59/16,A61K 31/155,31/315,33/30 

Priority Document No: 09/191,207 

(32) Priority Date: 12/11/1999 

(33) Name of priority country: US 


PCT/US99/24978 AND 25/10/1999 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: WESTFALL 

GEOFFREY 

Address of the Applicant: 80,ROBBINS 

ROAD,BROOKLYN,CONNECTICUT 

06234,USA 


1. WESTFALL GEOFFREY 




Composition systems , and methods for the prevention of mastitis in milk producing animals is provided . In 

particular, the compositions comprise a source of zinc, preferably zinc gluconate, and chlorhexidine. The 

composition is applied to the teat of a milk producing animal such as a cow either by dipping the teat 

therein or spraying the composition thereon. 

_________________________________________________________________ 




(54) Title of the invention: “ CO- 

CRYSTALLIZATION PROCESS” 

(51) International classification: B01D 

9/00,9/02,C07C 209/88 

(31) Priority Document No: 99200648.6 

(32) Priority Date: 05/03/1999 

(33) Name of priority country: EP 


PCT/EP00/01858 AND 03/03/2000 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: REUTER 

CHEMISCHE APPARATEBAU KG 


ENGESSERSTRASSE 4B,D-79108 

FREIBURG,GERMANY 


1. REUTER KARL 



A process for isolating enantiomer compounds from a mixture of compound through co-crystallization 

comprising the steps of (a) forming a solution comprising the mixture of enantiomer ® and (S) and cocrystallization 

agent C1 and C2 , wherein C1 and C2 are chiral with the provisio that at least one of C1 and C2 

is chiral and C1 and C2 do not form an enantiomeric pair, whereby C1 forms a co-crystal with ® and C1 

forms a co-crystal with (S); (b) super-saturating the solution in C1 ® and C2 (S); inducing crystallization of 

co-crystals of C1 ® and C2 (S) and (d) isolating the C1 ® co-crystals and C2 (s) co-crystals. 


_________________________________________________________________ 




(54) Title of the invention: TWO-CHAMBER TUBE 

(51) International classification: B65D 35/22,B29C 

7076,B29D 23/20,B65D 81/32 


(32) Priority Date: 16/03/1999 



PCT/EP00/02290 AND 15/03/2000 

(87) International Publication No: WO 00/55062 A1 



filed on: NIL 



filed on: NIL 


(71) Name of Applicant: ASIA 

AUTOMATION INDUSTRIELLE SA 

Address of the Applicant: ROUTE DE 

SAVOIE,CH-1896 

VOUVRY,SWITZERLAND 


1. KELLER GERHARD 

2. VOIGTMANN JEAN-PIERRE 





(19) INDIA (21) Application No IN/PCT/2001/01292 A 


(54) Title of the invention: A WRIST 

COMMUNICATION DEVICE HAVING MULTI- 

SECTIONED KEYPAD AND ANTENNA SYSTEM 

(51) International classification: H04M 1/00 

(31) Priority Document No: 09/330,728 ; 09/428,228 

(32) Priority Date: 11.06.1999; 27.10.1999 



PCT/US00/15854 – 09.06.2000 

(87) International Publication No: WO 00/78011 A3 – 

21.12.2000 



filed on: 



filed on: 


GHASSABIAN FIROOZ 


LOCUST COVE LANE, 

GREAT NECK, NY 11024, 

U.S.A 


(1) GHASSABIAN FIROOZ 





A wrist-mounted communication device (5) comprising a cellular phone mechanism (20) configured to 

transmit and receive communication signals. The device includes an antenna system (25) so as to transmit 

and receive singles. The antenna system further comprises at least one antenna (25) extendable away from 

the horizontal plane of the communication device. 


__________________________________________________________________ 


(19) INDIA (21) Application No.IN/PCT/2001/01308 A 


(54) Title of the invention: “THERMOSTAT AND 

STRUCTURE FOR MOUNTING SAID 

THERMOSTAT” 

(51) International classification: F61K 31/68 

(31) Priority Document No: 2000-223309 

(32) Priority Date: 25/07/2000 



PCT/JP01/05937 AND 09/07/2001 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: NIPPON 

THERMOSTAT CO.LTD. AND HONDA 

KOGYO KABISHIKI KAISHA 

Address of the Applicant 59-2,NAKAZATO 

6-CHOME,KIYOSE-SHI,TOKYO 204- 

0003,JAPAN AND 1-1,MINAMIAOYAMA 

2-CHOME,MINATO-KU,TOKYO 107- 

0062,JAPAN 


1. IWAKI TAKAHIRO 

2. HAMANO MASAHISA 

3. KAKEMIZU KENCHIRO 

4. KUROSAKA HITOSHI 

5. SATO KAZUHIKO 

5. YAGINUMA TADAO 




__________________________________________________________________ 



(22) Date of filing of Application 05/06/2002 (43) Publication Date: 24/06/2005 

(54) Title of the invention: “ METHOD OF 

CONTROLLING/REGULATING AN EMBOSSING 

PROCEDURE AND DRIVE AND CONTROL DEVICE 

FOR INJECTION MOLDING MACHINES 

(51) International classification: B29C 45/56 

(31) Priority Document No: PCT/CH00/00069 

(32) Priority Date: 09/02/2000 

(33) Name of priority country: CH 


PCT/CH01/00090 AND 09/02/2001 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant; NETSTAL- 

MASCHINEN AG. 


SWITZERLAND,INDUSTRISTRASSE,CH- 

8752 NAFELS,SWITZERLAND 


1. WEINMANN ROBERT 




__________________________________________________________________ 




(54) Title of the invention: “ DEVICE FOR 

CONTROLLING THE CLOSING OF A POWER 

BREAKER” 

(51) International classification: H01H 3/30 





PCT/DE00/04203 AND 22/11/2000 

(87) International Publication No: WO 01/39223A1 



filed on: NIL 



filed on: NIL 


(71) Name of Applicant: SIEMENS 



WITTELSBACHPLATZ 2,80333 

MUNICH,GERMANY 


1. LIEBETRUTH MARC 

2. GODESA LUDVIK . 




__________________________________________________________________ 




(54) Title of the invention: “ PRE-CUTTER AND 

EDGER MACHINE” 

(51) International classification: B24B 9/14 


(32) Priority Date: 21/12/1999 



PCT/US00/33979 AND 15/12/2000 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: JOHNSON & 

JOHNSON VISION CARE INC 

Address of the Applicant: 7500 CENTURION 

PARKWAY,SUITE 100,JACKSONVILLE,FL 

32256 USA 


1. ULLOA JOSE 




__________________________________________________________________ 




(54) Title of the invention: “ TOP COMB FOR A 

COMBING MACHINE” 

(51) International classification: D01G 19/28 


(32) Priority Date: 19/02/2000 



PCT/EP01/01072 AND 01/02/2001 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: STAEDTLER & UHL 


NORDLICHE,RINGSTRASSE 12,91126 

SCHWABAG,GERMANY 


1. GRUBER PETER 

2. GRAINGER CLIVE FILLEUL . 




________________________________________________________________ 




(54) Title of the invention: “ APPAARATUS FOR 

MIXING” 

(51) International classification: B01F 7/26 

(31) Priority Document No: PQ 5039 

(32) Priority Date: 11/01/2000 

(33) Name of priority country: AU 


PCT/AU01/00018 AND 11/01/2001 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: COMMONWEALTH 

SCIENTIFIC AND INDUSTRIAL 

RESEARCH ORGANIZATION 

Address of the Applicant: LIMESTONE 

AVENUE, CAMPBELL,ACT 

2601,AUSTRALIA 


1. SHEPHERD IAN CLARENCE 

2. GRAINGER CLIVE FILLEUL . 




__________________________________________________________________ 




(54) Title of the invention: SCINTILLATOR 

CRYSTALS,METHOD FOR MAKING SAME USE 

THEREOF 

(51) International classification: C09K 11/85,C01F 

17/00,G01T 1/202 

(31) Priority Document No: 1014401 

(32) Priority Date: 17/02/2000 

(33) Name of priority country: NL 


PCT/EP01/01837 AND 16/02/2001 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: STICHTING VOOR 

DE TECHNISCHE WETENSCHAPPEN 

Address of the Applicant: VAN 

VOLLENHOVENLAAN 661,NL-3527 JP 

UTRECHT 


1. DORENBOS PIETER 

2. VAN EIJK CAREL WILHELM EDUARD 

3. GUDEL HANS-ULRICH 

4. KRAMER KARL WILHELM 

5. VAN LOEF EDGAR VALENTIJN 

DIEUWER 




__________________________________________________________________ 




(54) Title of the invention: METHOD OF 

MANUFACTURING A FIBRE-REINFORCED 

PRESSURE VESSEL 

(51) International classification: F17C 1/06,F16J 12/00 


(32) Priority Date: 04/02/2000 

(33) Name of priority country: NL 


PCT/NL01/00075 AND 01/02/2001 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: ADVANCED 

LIGHTWEIGHT CONSTRUCTIONS 

GROUP IINC 

Address of the Applicant: KLUYVERWEG 

2A,NL-2629 HT DELFT, 


1. DEBECKER ANDY 

2. VAN DER JAGT OSCARCHRISTOPH 

3. KOPPERT JAN JACOBUS MATTHIJS 







(54) Title of the invention: “ METHOD FOR 

OXIDIZING A THIOETHER GROUP INTO A 

SULFOXIDE GROUP” 

(51) International classification: C07C 315/02,C07D 

401/12 

(31) Priority Document No: P 200000595 

(32) Priority Date: 13/03/2000 

(33) Name of priority country: ES 


PCT/ES01/00088 AND 08/03/2001 



(71) Name of Applicant: ESTEVE QUIMICA 

S.A. 

Address of the Applicant: AVENIDA MARE 

DE DEU DE MONTSERRAT,12,E- 

08024,BARCELONA,SPAIN 


1. BERENGUER MAIMO RAMON 

2. CAMPON PARDO JULIO 

3. COPPI LAURA 




__________________________________________________________________ 




(54) Title of the invention: WHEEL PROVIDED 

WITH DRIVING MEANS 



(32) Priority Date: 26/01/2000 

(33) Name of priority country: NETHERLANDS 


PCT/NL01/00054 AND 26/01/01 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: SPECIAL 

PRODUCTS FOR INDUSTRY V.O.F 

Address of the Applicant: VLIJTSEWEG 

232,NL-7317 AN APELDOORN 

NETHERLANDS 


1. HEINEN ADRIANUS JOHANNES 




The invention relates to a wheel provided with electric driving means in the wheel, control. measuring 

operating mans in the wheel for operating the electric driving means and data communication means in the 

wheel. Additionally the invention relates to a method for coordinating at least two of such wheels attached 

to one vehicle. Additionally the invention relates to a wheel 

strut provided with vehicle attachment means for attaching the wheel strut to a vehicle, and wheel 

attachment means for attaching a 

wheel to the wheel strut, in which the wheel attachment means are rotatable about the longitudinal] 

axis with respect to the vehicle 

attachment means and in which the wheel strut is provided with driving means for rotating the wheel 

attachment means. The invention 

also relates to a wheel according to the invention provided with a wheel strut according to another 

aspect of the invention. 


__________________________________________________________________ 




(54) Title of the invention: “ PIPE COUPLING FOR 

PLASTIC PIPES” 

(51) International classification: F16L 47/06 


(32) Priority Date: 22/01/1999 



PCT/EP00/00405 AND 19/01/2000 

(87) International Publication No: WO 00/43706 



filed on: NIL 



filed on: NIL 


(71) Name of Applicant: BIOPROCESSORS 

CORPORATION 

Address of the Applicant: 1900 ADDISON 

STREET,MEZZANINE 

LEVEL,BERKLEY,CA 94704,USA 


1. JURY ANDREY ZARUR 

2. ANGELINO MARK D 




__________________________________________________________________ 




(54) Title of the invention: “METHOD FOR 

ISOLATING POLYMER RESIN FROM SOLUTION 

SLURRIES” 

(51) International classification: C08G 65/46,64/40 


(32) Priority Date: 04/05/2000 



PCT/US00/32869 AND 04/12/2000 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: GENERAL 

ELECTRIC COMPANY 

Address of the Applicant: 1 RIVER 

ROAD,SCHENECTADY,NEW YORK 12345 

USA 


1 BATES GARY MELL 

2. GUO HUA 




Soluble polymer resins are separated from a solution slurry with the use of a precipitation aid where the 

slurry contains the polymer resin in both a soluble form and a solid particulate phase.The precipitation aid 

absorbs onto the surface of the solid polymer resin particulates and is suitable blend component for 

formulations of the polymer resin. The solution slurry may be concentrated and heated prior to precipitation 

of the polymer resin. 

__________________________________________________________________ 


(19) INDIA (21) Application No. 92/KOLNP/2003 


(54) Title of the invention: EXPANDED PERLITE 

PRODUCTS WITH CONTROLLED PARTICLE SIZE 

DISTRIBUTION 

(51) International classification: B01J 20/10 


(32) Priority Date: 08/08/2000 



PCT/US01/15685 AND 14/05/2001 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: ADVANCED 

MINERALS CORPORATION 

Address of the Applicant: 130 CASTILIAN 

DRIVE,SANTA BARBARA,CALIFORNIA 

93117,USA 


1. PALM SCOTT K 

2. WANG BO 

3. HAYWARD CHRISTOPHER 

4. ROULSTON JOHN S. 




Expanded perlite products having controlled particle size, distribution, method of producing the expanded 

perlite products, and methods of use thereof are provided. The expanded perlite product has, for example, a 

low ratio of standard deviation of aprticle size distribution to median particle size (for example, less than 

0.63) and low median particle size (for example, less than 50 microns.) The expanded perlite product may 

be used in a variety of applications including filter applications. 


__________________________________________________________________ 


(19) INDIA (21) Application No. 199/KOLNP/2003 A 


(54) Title of the invention: “SYSTEM AND 

METHOD FOR FACILITATING TRANSACTIONS 

INVOLVING DISTRIBUTION OF EQUIPMENT 

AND POST-INSTALLATION SUPPLY AND/OR 

SERVICE FO THE EQUIPMENT” 



(32) Priority Date: 17/08/2000 



PCT/BE01/00136 AND 16/08/2001 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: ATLAS COPCO 

AIRPOWER NAAMLOZE VENNOOTSCHAP 


BOOMSESTEENWEG 957,B-2610 

WILRIJK,BELGIUM 


1 HENDRICKK LUC GUSTAAF ANNA 

MARIE 

2. BADO EMILE MICHEL 

3.PETERSSON JOHAN GEORG URBAN 




__________________________________________________________________ 


(19) INDIA (21) Application No.274/KOLNP/2003 A 


(54) Title of the invention: “ METHOD AND DEVICE 

FOR THE CONTINUOUS SINGLE-STEP 

PRODUCTION OF A HOMOGENEOUS SOLUTION 

OF CELLULOSE IN HYDROUS TERITARY 

AMINOXIDES” 

(51) International classification: D01F 2/00,D01D 

1/02,C08B 1/00,C08J 3/11,3/09,C08L 1/02 



(33) Name of priority: 


PCT/DE00/03035 AND 05/09/2000 




filed on: NIL 



filed on: 


(71) Name of Applicant: THURINGSCHES INSTITUT 

FUR TEXTIL-UND KUNSTSTIOFF-FORSCHUNG 

E.V. AND LIST A.G. 


BREITSCHNEIDSTRASSE 97 D- 

07407,RUDOLSTADT,GERMANY AND 24,CH-4422 

ARISDROF,SWITZERLAND 


1. CHRISTOPH MICHELS 

2. ANDREAS DIENER 




__________________________________________________________________ 




(54) Title of the invention: “ ORGANIC 

COMPOUND HAVING CYANO GROUP AND 

INSECTICIDES/MITICIDES 

(51) International classification: C07C 

255/63,321/28,C07D 231/16,A01N 37/34 


(32) Priority Date: 02/11/2000 



PCT/JP01/09581 AND 01/11/2001 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: NIPPON SIDA 

CO.LTD. 

Address of the Applicant: 2-1 OHTEMACHI 2- 

CHOME,CHIYODA-KU,TOKYO,JAPAN 


1. SHIBATA YASUSHI 

2. HANTANO RENPEI 

3. MAKITA TAKAO 

4. MAKITA SATORU 

5. HANAI DAISUKE 

6. YAMAGUCHI MASAO 

7. ICHIKAWA NAOMI 




__________________________________________________________________ 


(19) INDIA (21) Application No. 806/KOLNP/2003 A 


(54) Title of the invention: “PARALLEL 

ELECTRONIC ARCHITECTURE COMPRISING A 

PLURALITY OF PROCESSING UNITS 

CONNECTED TO A COMMUNICATION 

BUS,AND ADDRESSABLE BY THEIR 

FUNCTIONAL CAPABILITIES” 



(32) Priority Date: 22/12/2000 

(33) Name of priority country: FR 


PCT/FR01/04176 AND 21/12/2001 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: WANY S.A. 

Address of the Applicant: AVENUE DE 

L’EUROPE,CAP ALPHA,F-34830 

CLAPIERS,FRANCE 


1 LAVAREC ERWAN 

2. TEMEL LAURENT 



The Patent Office Journal 24.06.2005 18060

_______________________________________________________________ 




(54) Title of the invention: “USE OF AN ADENOSINE 

A3 RECEPTOR AGONIST FOR INHIBITOR OF 

VIRAL REPLICATION” 



(32) Priority Date: 16/01/2001 



PCT/IL02/00028 AND 13/01/2002 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: CAN FITE 

BIOPHARMA LTD 

Address of the Applicant BAREKET 

STREET 10,49170 PETACH 

TIKVA,ISRAEL 


1. FISHMAN PNINA 

2. KHALILI KAMEL 




Present invention concerns the use of an active ingredient selected from the group consisting of agnonists of 

the adenosine receptor system, for inhibiting viral replication in cells. In particular, the invention provides a 

composition and method for inhibiting viral replication in cells, the method comprising presenting to the 

cells an effective amount of the active ingredient. According to one embodiment, the adenosine agonist is 

an A3 receptor agonist (A3RAg). The invention is particularly useful, for although not limited to, inhibiting 

the replication of HIV virus in human cells. 


__________________________________________________________________ 


(19) INDIA (21) Application No 926/KOLNP/2003 A 


(54) Title of the invention: STABILIZED SPINEL 

BATTERY CATHODE MATERIAL AND METHODS 

(51) International classification: H01M 4/50, 4/02 


(32) Priority Date: 31.01.2001 



PCT/US02/01342 – 18.01.2002 

(87) International Publication No: WO 02/061865 A3 – 

08.08.2002 



filed on: 



filed on: 


(71) Name of Applicant: KERR- 

MCGEE CHEMICAL, LLC 


ROBERT S. KERR, 

OKALHOMA CITY, OK 73102, 

U.S.A 


(1) HOWARD WILMONT F. 

JR. 

(2) SHEARGOLD STEPHEN W 

(3) STORY PHILLIP M 

(4) PETERSON ROBERT L. 





__________________________________________________________________ 




(54) Title of the invention: “C2,5’-DISUBSTITUTED 

AND N6,C2,5-TRISUBSTITUTED ADENOSINE 

DERIVATIVES AND THEIR DIFFERENT USES” 

(51) International classification: C07H 19/00 


(32) Priority Date: 03/03/2001 

(33) Name of priority country: GB 


PCT/IL02/00160 AND 18/03/2002 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: UNIVERSITEIT 

LEIDEN AND CAN FITE CIOPHARMA 

LTD. 

Address of the Applicant GORLAEUS 

LABORATORIES EINSTEINWEG 55 NL 

2333 CC LEIDEN NETHERLANDS 

10,BAREKET STREET, 49170 PETACH 

TIKVA,ISRAEL 


1. VAM TILBURG ERICA 

2. IJZERMAN AD 




The present invention concerns novel C2,5’- disubstituted and N 6 C2-5’ – trisubstituted adenosine 

derivatives and their different uses. The adenosine derivatives were found to be potent adenosine receptor 

agonists and thus are of a therapeutic value in the treatment and prophylaxis of diseases and disorders 

affected by adenosine receptors agonists. 

__________________________________________________________________ 




(54) Title of the invention: FLAKY PIGMENTS 

(51) International classification: C09C 1/00, 3/00 

(31) Priority Document No: NIL 

(32) Priority Date: NIL 



PCT/EP01/01682 – 15.02.2001 


22.08.2002 



filed on: 



filed on: 


MERCK PATENT GMBH 


FRANKFURTER STRASSE 

250, 64293 DARMSTADT, 

GERMANY 


(1) EIJI UMEHARA 

(2) KOUSHIRO KUNII 





A flaky pigment excellent in leafing properties and in adhesion between pigment particles and a coating 

(resin) was obtained by coating the surface of flaky pigment with a coupling agent and a phosphaste having 

a perfluoroalkyl group or a silane compound. Accordingly, the flaky pigment is excellent as a pigment for 

coating or printing ink of which brightness and durability are required. 


__________________________________________________________________ 


(19) INDIA (21) Application No. 1151/KOLNP/2003A 


(54) Title of the invention: “MILLING CUTER AND 

CUTTING INSERT THEREFOR” 



(32) Priority Date: 04/07/2001 

(33) Name of priority country: IL 


PCT.IL02/00463AND 16/06/2002 

(87) International Publication No: WO 03/004206 A1 



filed on: NIL 



filed on: NIL 


(71) Name of Applicant: ISCAR LIMITED 

Address of the Applicant: P.O. BOX 11,24959 

TEFEN, ISRAEL 


1 SATRAN AMIR 

2. ULIANITSKY DANIEL 




__________________________________________________________________ 




(54) Title of the invention: OPTICAL ISOMER 

SEPERATING FILLER PRODUCTION METHOD 

THEREFOR AND APPLICATION METHOD 

THEREFOR 

(51) International classification: B01J 20/22,20/30 


(32) Priority Date: 12/04/2001 

(33) Name of priority country: JP 


PCT/JP02/03688 AND 12/04/2002 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: DAICEL 

CHEMICAL INDUSTRIES LTD. 

Address of the Applicant 1 

TEPPOCHO,SAKAI-SHI.OSAKA 590- 

8501,JAPAN 


1. IKEDA HIROKAZU 

2. ONISHI ATSUSHI 

3. MURAZUMI KOICHI 




An optical isomer separating filler capable of separating an optical isomer mixture with a good separating 

performance a production method therefore and an application method therefore. A production method for 

an optical isomer separating filler characterized by stirring a carrier and an optically-active polymer 

compound solution in a 2-axis vertical stirring device, an optical isomer separating filler produced by the 

production method , and an application method in which the optical isomer separating filler is used in a 

liquid chromatography separation method and a pseudo-moving-bed chromatography separation method. 





(54) Title of the invention: “ 4-STROKE ENGIEN 

CONTROL DEVICE AND CONTROL METHOD” 

(51) International classification: F02D 41/04,41/34 


(32) Priority Date: 12/07/2001 



PCT/JP02/07122 AND 12/07/2002 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: YAMAHA 

HATSUDOKI KABUSHIKI KAISHA 

Address of the Applicant: 2500 

SHINGI,IWATA-SHI,SHIZUOKA,438 

8501,JAPAN 


1. HASEGAWA HIROSHI. 

2. SAWADA YUICHIRO 




__________________________________________________________________ 




(54) Title of the invention: “THERAPEUTIC 

DELIVERY OF CARBON MONOXIDE” 

(51) International classification: A61K 

31/28,31/295,33/24,A61P 

9/00,9/12,15/10,29/00,35/00,39/06/,41/00 


(32) Priority Date: 15/05/2001 

(33) Name of priority country: GB 


PCT/GB02/02268 AND 15/05/2002 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: NORTHWICK 

PARK INSTITUTE FOR MEDICAL 

RESEARCH 


HARROW,MIDDLESEX HA1 3UJ UNITED 

KINGDOM 


1 MOTTERLINI ROBERTO ANGELO 

2. MANN BRAIN ERNEST 




__________________________________________________________________ 




(54) Title of the invention: “INDIVIDUAL PLANT 

WATERING DEVICE” 

(51) International classification: A01G 27/00,29/00 


(32) Priority Date: 16/07/2001 

(33) Name of priority country: FR 


PCT/FR02/02273 AND 01/07/2002 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: AMSELLEM 

MAURICE 

Address of the Applicant: 58,RUE DE LA 

BALME,F-69003 LYON,FRANCE 


1. AMSELLEM MAURICE 




The invention concerns a fitting consisting of a part made of injected plastic for connecting a water tank (1) 

and a hollow cone (2) made of porous ceramics, so as to produce a device for dispensing water individually 

to plants, in particular potted plants, proximate to their roots, and in predetermined amount, comprising 

three coaxial parts: a disc-shaped intermediate part (4) with a central hole (5); a part (A) consisting of one 

or two cylinders, arranged on one side of the disc (4) and designed to be permanently fixed to the cone (2); 

a part (B) consisting like part A of one or two cylinders bearing a thread on the inner surfaces, arranged on 

the other side of the disc (4) and capable of receiving a bottle (1) removably screwed. 


__________________________________________________________________ 




(54) Title of the invention: “ CLUTCH 

MECHANISM LUBRICATING STRUCTURE OF 

ENGINE” 

(51) International classification: F16D 13/74 


(32) Priority Date: 08/04/2002 



PCT/JP03/04466 AND 08/04/2003 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: YAMAHA 

HATSUDOKI KABUSHIKI KAISHA 

Address of the Applicant: 2500 

SHINGAI,IWATA-SHI,SHIZUOKA 438-8501 

JAPAN 


1. OISHI AKIFUMI 

2. ISHIDA YOUSUKE 




__________________________________________________________________ 




(54) Title of the invention: “PROTECTIVE DEVICE 

FOR A NEEDLE” 

(51) International classification: A61M 5/50,5/32 

Priority Document No: B02001A0000497 

(32) Priority Date: 31/07/2001 

(33) Name of priority country: ITALY 


PCT/EP02/08534 AND 30/07/2002 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: DELTA MED 

S.R.L. 

Address of the Applicant: GERBOLINA 15 I- 

46019 VIADANA (MANTOVA) ITALY 


1. VILLA DANILO 

2. MINARI EMANUELE 




__________________________________________________________________ 




(54) Title of the invention: “COLUMN TRAY” 

(51) International classification: B01D 3/16,B01J 

19/30 


(32) Priority Date: 17/08/2001 



PCT/EP02/09253 AND 19/08/2002 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: QVF ENGINEERING 

GMBH 


HATTENBERGSTRASSE 36,55122 MAINZ 

GERMANY 


1 DICHTL GOTTFRIED 

2. WALTER ULRICH 




__________________________________________________________________ 




(54) Title of the invention: “SERIAL CANCELLATION 

RECEIVER DESIGN FOR A CODED SIGNAL 

PROCESSING ENGINE” 

(51) International classification: G01S 

(31) Priority Document No: 60/348,106 

(32) Priority Date: 15/01/2002 



PCT/US03/00928 AND 13/01/2003 

(87) International Publication No: WO 03/060546 A2 



filed on: NIL 



filed on: NIL 


(71) Name of Applicant: TENSORCOMN 

INCORPORATED 

Address of the Applicant 1490 WEST 121 ST 

SVENUE,SUITE 105,WESTMINISTER,CO 

80234 USA 


1. OLSON ERIC S. 

2. NARAYAN ANAND P 

3. THOMAS JOHN K 




__________________________________________________________________ 




(54) Title of the invention: “SYSTEM AND 

METHOD FOR POLLING A PROTIOCOL DATA 

UNIT OF A TRANSMISSION BUFFER” 

(51) International classification: H04L 29/06 



(33) Name of priority country: KR 


PCT/KR02/02071AND 07/11/2002 

(87) International Publication No: WO 03/047206 A1 



filed on: NIL 



filed on: NIL 



(19) INDIA (21) Application No.865/KOLNP/2003 

(71) Name of Applicant: LG ELECTRONICS 

INC 

Address of the Applicant: 20,YOIDO- 

DONG,YOUNGDUNGPO-KU,150- 

010,SEOUL,REPUBLIC OF KOREA 


1 YIO SEUNG-JUNE 

2. YEO-WOON YOUNG 

3. LEE SO-YOUNG 




(54) Title of the invention: “METHOD OF 

CLARIFYING BYER PROCESS LIQUORS USING 

SALICYCLIC ACID CONTAINING POLYMERS” 



(32) Priority Date: 29/01/2001 



PCT/US01/48585 AND 11/12/2001 


(71) Name of Applicant: ONDEO NALCO 

COMPANY 

Address of the Applicant ONDEO NALCO 

CENTER,NAPERVILLE,IL 60563,USA 


1. QUADIR MURAT 

2. OHILLIP EVERETT 

3. BRAMMER LARRY 

4. MAHONEY ROBBERT 

5. KILDEA JOHN L. 

6. RAMESH MANIAN 

7. MALITO JOHN T. 


A method of flocculating suspended solids in a Bayer process liquor comprising adding to the liquor an 

effective amount of a polymer comprising salicylic acid group. 


__________________________________________________________________ 




(54) Title of the invention: “METHOD AND DEVICE 

FO RCONDUCTING MODULAR MULTIPLICATION 

AND ARITHMETIC-LOGIC UNIT FOR 

CONDUCTING MODULAR MULTIPLICATION” 



(32) Priority Date: 16/02/2001 



PCT/EP02/00719 AND 24/01/2002 


filed on: NIL 


(71) Name of Applicant: INFINEON 

TECHNOLOGIES AG. 

Address of the Applicant ST.MARTIN 

STRASSE 53,81699 

MUNCHEN,GERMANY 


1. ELBE ASTRID 

2. SEDLAK HOLGER 

3. JANSEEN NORBERT 

4. SEIFERT JEAN PIERRE 




__________________________________________________________________ 



(22) Date of filing of Application 22.06.2004 (43) Publication Date: 24/06/2005 

(54) Title of the invention: SEAM WELDING DEVICE 


(31) Priority Document No: JP 2002-21401 

(32) Priority Date: 30.01.2002 



PCT/JP03/00916 – 30.01.2003 


07.08.2003 



filed on: 



filed on: 


(71) Name of Applicant: (1) 

DENGENSHA MFG. CO. LTD. 

& (2) XENESYS INC. 

Address of the Applicant: (1) 23- 

1, MASUGATA 1-CHOME, 

TAMA-KU, KAWASAKI SHI, 

KANAGAWA-KEN, JAPAN & 

(2) 20-23, NISIKIGAOKA 3- 

CHOME, UOZUMI-CHO, 

AKASHI-SHI, HYOGO-KEN, 

JAPAN 


(1) MATSUZAKI TOYOAKI 

(2) SHIBA SHOJI 






__________________________________________________________________ 




(54) Title of the invention: “DEVICE AND 

METHOD FOR THE SURFACE TRATMENT OF 

PARTS” 

(51) International classification: H04B 7/26 

(31) Priority Document No: 10-2002-0000632 

(32) Priority Date: 05/01/2002 

(33) Name of priority country: KR 


PCT/KR02/02510 AND 31/12/2002 


A1 



filed on: NIL 



filed on: NIL 


(71) Name of Applicant: LG ELECTRONICS 

INC 

Address of the Applicant: 20,YOIDO- 

DONG,YOUNGDUNGPO-GU,150- 

010,SEOUL,REPUBLIC OF KOREA 


1 YI SEUNG-JUNE 

2. YEO WOON-YOUNG 

3. LEE SO-YOUNG 




__________________________________________________________________ 




(54) Title of the invention: “AN AVIAN EMBRYO 

PARTICULATE BIOMASS FOR THE PRODUCTION 

OF VIRUS ANTIGENS” 

(51) International classification: C12N 5/06,7/00 


(32) Priority Date: 21/12/2001 



PCT/US02/40567 AND 18/12/2002 




filed on: NIL 



filed on: NIL 

(71) Name of Applicant: WYETH 

Address of the Applicant FIVE GIRALDA 

FARMS,MADISON,NJ 07940,USA 


1. WEDERQUIST DAVID LOU 




The present invention provides a biomass which comprises avian embryonic particles having a particle size 

of about 0.5 mm to 10.0 mm and the use thereof in a method for the production of virus antigens. Also 

provided is a method for the preparation of a vaccine useful for the amelioration and prevention of viral 

diseases. 


__________________________________________________________________ 


(19) INDIA (21) Application No.970/KOLNP/2004A 


(54) Title of the invention: “TRANSLATOR” 

(51) International classification: H01F 38/18 


(32) Priority Date: 30/01/2002 



PCT/EP03/00578AND 22/01/2003 




filed on: NIL 



filed on: NIL 


(71) Name of Applicant: WOBBEN 

ALLOYS 

Address of the Applicant ARGESTRASSE 

19, 26607 AURICH GERMANY 


1. WOBBEN ALLOYS 




__________________________________________________________________ 


(19) INDIA (21) Application No. 1243/KOLNP/2004 A 


(54) Title of the invention: “PREPARATION OF 

PROSTAMIDES” 

(51) International classification: C07C 405/00 


(32) Priority Date: 01/03/2002 



PCT/US2003/006071 AND 28/02/2003 


A3 



filed on: NIL 



filed on: NIL 


(71) Name of Applicant: ALLERGAN INC 

Address of the Applicant: 2525 DUPONT 

DRIVE,T2-7H IRVINE,CA 92612,USA 


1 GRAST MICHAEL E 

2. OUDENES JAN 

3. ANTCZAK CASIMIR GREGORY 

4. MORTIMER RICHARD DONALD 

5. LU YEE-FUNG 

6. HOCHFELLNER BRIAN GEORGE 

7. ARSENAULT EDWARD ARMAND 

8. YEH WEN-LUNG 




18 Months Publication 

The following patent applications have been published under section 11A of the Patents 

(Amendment) Act. 2005. 

(21) Application No.3626/DEL/1997 A (22) Date of filing of Application: 16/12/1997 

(54) Title of the invention: “ ELECTROLYTE INJECTION SYSTEM.” 

(51) International Classification 7 :H01M 2/36 


(31) Document No.:97-11780 

(32) Date:31/03/1997 

(33) Name of convention country: KOREA 

(66) Filed U/s 5(2): NIL 







SAMSUNG DISPLAY DEVICESCO. LTD., 


575, Sin-dong, Paldal-ku, Suwon-si, Kyungkido, 

Korea. 


EUI-SUN HONG. 


Disclosed is an electrolyte injection system which forms a means in a head portion to prevent 

a secondary battery from wetting with electrolyte on anode tab and an upper surface of a 

beading portion by directly injecting electrolyte from an injection nozzle to an electrode 

assembly during injection of electrolyte. 

18081

(21) Application No. 3406/DEL/1997 A (22) Date of filing of Application: 26/11/997 

(54) Title of the invention: “AN AUTOMATED BANKING MACHINE APPARATUS 

AND A METHOD OF PREVENTING CUTTING OF 

PAPER SHEETS THEREIN.” 

(51) International Classification 7 :B41 J 11/70 

B41J 11/46; B65H 29/58 


(31) Document No.:60/031,501 

08/827,567 

(32) Date:27/11/1996 

28/03/1997 

(33) Name of convention country: U.S.A 








INTERBOLD, 


5995 Mayfair Road, North Canton, Ohio 44720, 

United States of America. 


THOMAS SCOTT MASON 

JEFFREY ANDREW BRANNAN 

TIMOTHY RICHARD HOOVER. 


A receipt form handling system for an automated banking machine includes a printer (3) 

which prints indicia on paper extending a paper path (151) . Paper is moved in the paper 

path by engagement with a drive mechanism (157, 159). Paper sheets are delivered by the 

drive mechanism to a delivery area, which includes a nip (114) of a sheet transport (26). 

The transport removes the sheets from the delivery area. A cutter (153) is positioned in the 

paper path and operates to selectively cut the paper. A sensor (155) is positioned at a 

location in the paper path upstream from the cutter. A controller (112) is in operative 

connection with the sensor and the cutter. The controller operates the cutter so that the paper 

is cut to produce a form sheet after indicia is printed on a portion of the paper. 

Upon the sensor detecting an approaching end of the paper, the controller ceases operation of 

the cutter. This avoids producing forms that are of insufficient length to be handled by the 

drive or transport 

18082

(21) Application No. 3731/DEL/1997 A (22) Date of filing of Application: 22/12/1997 

(54) Title of the invention: “A DIGITAL PHASE-LOCKED LOOP AND A METHOD 

AND SYSTEM FOR CONTROLLING IT.” 

(51) International Classification 7 :H03L 7/085 

H04J 3/07 


(31) Document No.:1507/96 

(32) Date:23/12/1996 










TELLABS DENMARK A/S, 


Lautrupbjerg 7-11, DK-2750 Ballerup, 

Denmark. 


PER H. THOMSEN. 

A digital phase –locked loop comprises a numerically controlled oscillator (5) which is 

capable of generating a clock signal by dividing a system clock frequency by a factor 

determined by a control word, and a phase detector (2;3) which is capable of generating the 

control signal and an response to a phase difference between the clock signal and an external 

reference signal so that the control word assumes a nominal value when the phase difference 

is numerically smaller than a given value, and may assume on or more other values when 

the phase difference is numerically greater than the given value. The loop moreover 

comprises means (7) which, when the phase difference is numerically greater than the given 

value, may modulate the control word. A corresponding method is also disclosed. 

18083


(54) Title of the invention: “ASYNCHRONOUS DATA PIPE CONFIGURED FOR 

COUPLING BETWEEN AN APPLICATION AND A BUS 

STRUCTURE.” 

(51) International Classification 7 :H04J 3/24 


(31) Document No.:08/612,322 

(32) Date: 07/03/1996 










SONY ELECTRONICS, INC., 


1 Sony Drive, Paark Ridge, New Jersey 07656- 

8003, United State of America. 


SCOTT D. SMYERS. 

An asynchronous data pipe (ADP) automatically generates transaction necessary to complete 

asynchronous data transfer operations for an application over a bus structure. The ADP 

includes a register file which is programmed and initiated by the application. The register file 

includes the bus speed, transaction label, transaction code, destination node identifier, 

destination offset address, length of each data packet, packet counter, packet counter bump 

field, control field and a status field. During a data transfer operation, the ADP generates the 

transactions necessary to complete the operation, over the appropriate range of addresses, 

using the information in the register file as a template. The ADP increments the value in the 

destination offset address filed for each transaction according to the length each data packet, 

unless the incrementing feature has been disabled and the transactions are to take place at a 

fixed address. The packet counter represents the number of transactions remaining to be 

generated. The packet counter value is decremented after each packet of data is transferred. 

The application can increment the packet counter value by writing to the packet counter bump 

field. A multiplexer is included within a system having multiple ADPs for multiplexing the 

information from the ADPs onto the bus structure . A demultiplexer is included within a 

system having multiple ADPs for routing information from the bus structure to the 

appropriate ADP. 

18084

(21) Application No.696/DEL/2001 A (22) Date of filing of Application: 22/06/2001 

(54) Title of the invention: “ HOLDER ASSEMBLY FOR INCANDESCENT ELECTRIC 

LAMPS.” 

(51) International Classification 7 : 


(31) Document No.: 

(32) Date: 










PHOENIX LAMPS INDIA LIMITED, 


59-A, N.E.P.Z.,Noida Phase-II, Dist. Gautam 

Budh Nagar,Uttar Pradesh, Pin – 201 305, 

India. 


BHAGWAT, RAMACHANDRA - 

SHRIKRISHNA. 

An improved incandescent holder assembly is disclosed. The assembly is characterized by a 

novel biasing means with two downwardly extending arms which are located around the pinch 

portion of the bulb. The biasing means has an outwardly extending end portion, which when 

depressed , causes the two arms to open outwards, away from said pinch portion so that the 

biasing means does not foul against the pinch portion, nor does the pinch portion obstruct the 

spring action of said biasing means. The radially inward force developed as result of the 

opening of the downwardly extending arms is approximately 75% higher as compared to the 

prior art assemblies making the lamp assembly of the present invention more rigid and 

strong.. 

18085


(54) Title of the invention: “SWITCHGEAR CABINET WITH AN ASSEMBLED 

SHELF UNIT.” 

(51) International Classification 7 :H02B 1/30 


(31) Document No.:196 47 753.0-34 

(32) Date: 19/11/1996 










RITTAL-WERK RUDOLF LOH GmbH & Co, 

KG., 


Auf Dem Stutzelberg, 35745 Herborn, 

Germany. 


WALTER NICOLAI. 

The invention relates to a switchgear cabinet with a rack, which has vertical frame members, 

the vertical frame members being connected to a bottom or top unit. The incorporation of 

electronic components is then possible with little outlay if two adjacent vertical frame 

members are connected with connector pieces to form a separate assembly unit and the builtin 

components may be secured thereto. 

18086

(21) Application No.IN/PCT/2001/00476/DEL A (22) Date of Application: 04/06/2001 

(54) Title of the invention: “ A SYSTEM FOR CONTROLLINGA ROTATABLE 

DEVICE.” 

(51) International Classification 7 :H02P 7/36, 

5/28. 


(31) Document No.: PP 6961 

(32) Date:06/11/1998 


AUSTRALIA. 









BRITS, LUDWIG EMMA & CHRISTIE, 

VICTOR JOHN, 


32A Sterling Street, Manunda, Queensland 

4870, Australia & 8 Longden Street, 

Brinsmead, Queensland 4870, Australia. 


BRITS, LUDWIG EMMA 

CHRISTIE, VICTOR JOHN. 

A system for controlling a rotatable device, the system comprising a controller and a rotary 

device, which has a stator and a rotor wherein the controller is connected to the rotary device 

to control rotation of the rotary device , and wherein the controller is adapted to periodically 

energise at least one energizing coil of the device to create magnetic filed of a polarity which 

induces the rotor to rotate in the single direction and wherein the controller is switched off 

so as to de-energising coil when other forces, produce a resultant force which induces rotation 

of the rotor in the single direction. 

18087


(54) Title of the invention: “ AN AUTOMATED BANKING MACHINE.” 

(51) International Classification 7 :G06F 17/60 


(31) Document No.:60/031,956 

(32) Date:27/11/1996 

(33) Name of convention country:U.S.A 








INTERBOLD, 





JAY PAUL DRUMMOND 

DALE BLACKSON 

LILEI CHEN 

BOB ANDREW CICHON 

MARK STEVEN COVERT 

BRADRICK QUINTIN LEPPER 

MARK ATAN MOALES 

MARK DAVID SMITH 

ROBERT JOHNSON LEMLEY 

MICHAEL EDWARD CALIFF, JR 

SHAWN D JOYCE 

PHILLIP SHAVAN MOORE 

STEVEN CARL SWINGLER. 


An automated banking machine (12) is operative to conduct transactions in response to 

HTML documents and TCP/IP messages exchanged with a local computer system (14) 

through an intranet (16), as well as in response to messages exchanged with foreign servers 

(20,22,24,26,28,96) in a wide area network. (18). The banking machine includes a computer 

(34) having an HTML document handling portion (76), 80,82). The HTML document 

handling portion is operative to communicate through a proxy server (88) , with a home 

HTTP server (90) in the intranet or the foreign servers in the wide area network. The 

computer further includes a device application portion (84) which interfaces with the HTML 

document handling portion and dispatches messages to operate devices (36) in the automated 

banking machine. The devices include a sheet dispenser mechanism (42) which dispenses 

currency. The device application portion communicates with a device interfacing software 

portion (64) in the banking machine through a device server (92) in the intranet. The device 

server maintains local control over the devices in the banking machine including the sheet 

dispenser. The banking machine operates to read indicia on the user’s card corresponding to a 

system address. The computer is operative to connect the banking machine to the home or 

foreign server corresponding to the system address, which connected server operates the 

banking machine until the completion of transactions by the user. 

18088


(54) Title of the invention: “A CORRUGATED ROOF MATERIAL.” 

(51) International Classification 7 : E04 D3/35, 

E04 C2/292. 


(31) Document No.:9613766 

(32) Date: 12/11/1996 

(33) Name of convention country: FRANCE 









ONDULINE, 


38, rue Saint Ferdinand, 75017 Paris, France. 


ALBERT COSTI. 

A corrugated roof support material, comprising a roofing sheet with parallel corrugations of 

peaks and valleys, said peaks having plural hollow areas for receiving roofing title tenons 

therein, said hollow areas being aligned across said peaks substantially perpendicular to the 

corrugation,and characterized in that a ratio of an amplitude of the corrugations to a pitch of 

the corrugations is from 1:2 to 1:1. 

18089


(54) Title of the invention: “CLUTCH MECHANISM FOR YARN SUPPLY 

APPARATUS .” 

(51) International Classification 7 : F 16 D 13/04 


(31) Document No.:19726027 

(32) Date: 19/06/1997 







Total No Of Pages : 31 



MEMMINGER-IRO GmbH, 


Jakob-Mutz-Strasse 7, D-72280 Dornstetten, 

Germany. 


HERMANN SCHMODDE 

RICHARD KAUFMANN 

ALFRED LAMPPRECHT. 

A yarn supply apparatus is equipped with a clutch arrangement in order to couple a drive 

wheel to rotate with a yarn supply wheel as necessary. The clutch arrangement is 

constructed in an open design, in which any development of narrowing spaces is avoided. 

For this purpose one clutch half is provided with axial fingers, which engage in radically 

open longitudinal slots, formed by a toothing of the other clutch half. The slots of the 

toothing are longer than the engagement length between fingers and toothing. The 

intermediate space formed between the ends of the fingers and the nearest wall in axial 

direction is open in radial direction or is in communication with a larger inner space. 

Thereby the compression or compaction of deposited fluff is prevented. 

18090

(21) Application No. 266/DEL/99 A (22) Date of filing of Application:18/02/1999 

(54) Title of the invention: “APPARATUS FOR GUIDING BARS”. 


B21C 47/14 

B21C 47/34 

B 65H 20/00 


(31) Document No.:09/034,387 

(32) Date :04/03/1998 

(33) Name of convention country 

:U.S.A. 

(66) Filed U/s 5(2) : NIL 

(61) Patent of addition to application 

No. : NA 

(62) Filed on : NA 

(63) Divisional to Application No. 

:NIL 



MORGAN CONSTRUCTION COMPANY, 


Of 15 Belmont Street, Worcester, Massachusetts 01605, 



TERRENCE MICHAEL SHORE 

MELICHER PUCHOVSKY. 


Apparatus for guiding bars, rods and other like bendable elongated products moving 

longitudinally along a curved path (Pc), said apparatus comprising: 

First and second guide rollers (54a, 54b) arranged respectively along the inside and 

outside of said curved path, said first an second guide rollers coacting in pairs to define 

gaps there between spaced along said path and drive means (56) for rotatably driving 

said guide rollers; characterized by adjustment means (40a,44a,44b,42) for 

symmetrically shifting the guide rollers of each of said pairs in opposite directions with 

respect to said path to thereby vary the size of said gaps. 

18091


(54) Title of the invention: “AN IMPROVED PROCESS FOR THE PREPARATION OF 

BIS (HALO-NAPHTHALIMIDO) ALKYLENES”. 


C07D 317/00 



(32) Date : 

(33) Name of convention country : 

(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 




COUNCIL OF SCIENTIFIC AND INDUSTRIAL 

RESEARCH AND UNIVERSITY PIERRE ET 

MARIE CURIE. 


Rafi Marg, New Delhi-110 001 and Laboratoire de 

Synthese Macromoleculaire, 4, Place Jussieu, 75252 

Paris Cedex 05, France. 


OM PRAKASH SRINIVAS YEMUL 

SUNITA OMPRAKASH YEMUL 

SURENDRA PONRATHNAM 

CHELANATTU KHIZHAKKE MADATH RAMAN - 

RAJAN 

ALAIN FRADET. 

This invention relates to an improved process for the preparation of bis 

(halonaphthalimido ) alkylenes. The Process relates to the preparation of bis (4-halo- 

1,8-naphtalimido) alkylenes having general formula I given in drawing accompanying the 

specification wherein R=-(CH2)n—n=2 to 12 and x = halogen. Bis (4-halo-1,8naphtaalineimoido) 

compounds prepared by the process of this invention can be used to 

prepare high performance engineering polymers with good chemical and thermal 

stability. Suitable for the synthesis of soluble high perormance polymer by nucleophilic 

halo displacement polymerization reaction offering advantages of easse of operation and 

leading to improved yields as well. The process does not require the dioxan or toluene 

reflux as reported earlier. The process of the invention is amenable for scale up 

operation. 

18092


(54) Title of the invention: “AN AIR ASSIST DEVICE FOR AN INTERNAL 

COMBUSTION ENGINE”. 


F02B 29/00 



(32) Date : 


(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 




DEPARTMENT OF SCIENCE & TECHNOLOGY, 


Technology Bhavan, New Mehrauli Rod, New Delhi 

110016, Indian. 


MELKOTE VIRARAGHAVACHAR 

NARASHIMAN 

An air assist device for an internal combustion engine comprising: 

an air pump assembly having a cylindrical block; 

a hollow static core of conical configuration provided in the said cylindrical block; 

a piston body conforming to the said conical configuration of the static core to enable 

vertical movement of the said piston within the said static core having an outlet pot said 

piston being provided with piston rings, characterized in that; 

an ambient inlet port is provided within the said cylindrical block and a transfer port for 

communicating with the engine cylinder provided within the said air pump assembly; 

and 

crank and crank case connected within the air pump assembly by a connecting rod; 

wherein the said piston assembly and static core are conical in configuration having a 

cavity depth and tapered configuration proportional to the desired pump stroke of the 

engine. 

18093

(21) Application No.2386/DEL/1998 A (22) Date of filing of Application: 13/08/1998. 

(54) Title of the invention: “AN IMPROVED MULTI-DIRECTIONAL STAND USEFUL 

FOR A PORTABLE BURNER SYSTEM”. 




(32) Date : 


(66) Filed U/s 5(2) : NIL 


No. : NA 



NIL 





RESEARCH. 


Rafi Marg , New Delhi-110 001 India. 


HARISH KUMAR MADAN 

PREM NATH BHAMBI 

DHANI RAM 

NISHAN SINGH 

PRAN NATH KAPOOR 

GULAB CHAND GUPTA. 

The present invention provides an improved multidirectional stand useful for portable 

burner system. The invention relates to improvement in portable burner system which 

can be adjusted so as to produce flame along any direction at any point situated at any 

height in any plane in space with precision and care. 

18094

(21) Application No.IN/PCT/2002/00196/DEL A (22) Date of Application: 18/02/2002 

(54) Title of the invention: “PROCESS FOR THE PREPARATION OF AT LEAST 2L 

VOLUME POLYETHYLENE CONTAINER”. 


B 29C 49/00 


(31) Document No.:9919718.8 (32) 

Date :19/08/1999. 


UK 

(066) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 



BOREALIS TECHNOLOGY OY, 


FIN-06101 Porvo, FINLAND. 


NILSEN, JORUNN 

EGGEN, SVEIN 

THORN, LARS 

BAANN, HEGE VALE 


A process for the preparation of at least 2L volume polyethylene container which process 

comprises blow moulding a bimodal HDPE, wherein said HDPE contains an ethylene 

homopolymer and an ethylene copolymer, said bimodal HDPE having the following 

characteristics: 

a density of 940 to 970kg/m 3 

a weight average molecular weight of 200000to 450000D; 

a number average molecular weight of 6000to 20000D; 

a molecular weight distribution of 15 to 55; 

MFR21 of 2 to 12g/10min; 

Tensile modulus at least 900 mPa ;and 

A comonomer content of 0.5 to 10 wt%. 

18095

(21) Application No.01515/DELNP/2003 A(22) Date of Application:22/09/2003 

(54) Title of the invention: “A METHOD OF OPTIMIZING SYSTEM RESOURCES 

AND A SYSTEM THEREOF”. 


H04L 12/66 


(31) Document No.:09/812,994 

(32) Date :20/03/2001 


:U.S.A. 

(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 



MOTOROLA, INC., 


1303 East Algonquin Road, Schaumburg, Illinois 60196 

United States of America, 


RAJ KUMAR DESHPANDE 

ROGER WILLIAM ADY. 


A method of, and means for accomplishing the method, optimizing system resources in a 

network (102) using packetized voice telephony consists of the following steps: 

determining (302) that a packetized voice call form an originating gateway (104) 

terminates at a non-human voice interface system (108) , wherein the packetized voice 

call is assigned a specified high priority level; and transmitting (304) signaling to cause 

the originating gateway (104) to transmit the packetized voice call to the not –human 

voice interface system (108) at a lower priority than the specified high priority level. 

18096

(21) Application No. IN/PCT/2002/1151/DEL A (22) Date of filing of Application: 2/11/2002 

(54) Title of the invention: “DIAPHRAGMED AIR VALVE DEVICE”. 


F16K 3/03 

F02D 9/18 


(31) Document No.:S2000089 

(32) Date :23/05/2000 

(33) Name of convention country :ID 

(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 



WIJAYA HERU PRASANTA, 


Of Graha Famikli D. 183, Pr. Kali Kendal, Surabaya 

60226, Indonesia. 


WIJAYA, HERU, PRASANTA. 


A diapraghmed air valve system for automotive engines characterised in that: 

- a cylindrical air inlet and a valve opening constituted by small plates, 

- said small plates are linked with each other in an aerodynamic arrangement to control the 

size of the valve opening, for controlling the rate of flow of air, 

- an air streamline lying in the centre of the air inlet, 

- said air flowing into the engine at a rate controlled by the diameter formed by the said 

aerodynamic arrangement of plates such that the air flowing into the engine through the 

valve system keeps intact before and after entering the engine. 

18097


(54) Title of the invention: “MOUNTING FOR A DOOR LEAF”. 


E05 D5/02 


(31) Document No.:295 20 471.0 

295 20 472.9 

(32) Date :22/12/1995 


:GERMANY. 

(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 




SOCIETA ITALIANA PROGETTI S.R.L., 


Via Pacinotti, 26/28, 20013 Magenta, Italy. 


MARIO MARINONI. 

Mounting for a door leaf, a fanlight leaf or the like, particularly for an all glass leaf, having a 

plane clamping plate (1) and a plane counter clamping plate (2), which, in the region of an edge 

recess (3) in a leaf edge (5) of the leaf(4), be attached to the two opposite surfaces, and the leaft 

(4) be pinched between the clamping plate (1) and the counter clamping plate (2) by means of 

fastening screws (7) joining the clamping plate (1) and the counter clamping plate (2), wherein 

at the clamping plate (1) a plane web plate (9) with a rectangular cross-section is formed 

extending perpendicular to the clamping plate (1), said web plate (9), in the assembled condition, 

spans over the distance between the clamping plate (1) and the counter clamping plate (2) and 

extends through the edge recess (3) , characterized in that the counter clamping plate (2) is 

provided with a rectangular recess (17,41), being adapted to the shape of the free end of the web 

plate (9), the web plate(9) in the assembled condition, engaging by means of its free end with the 

rectangular recess (17,41), wherein the clamping plate (1) inclusive of the web plate (9) and 

counter clamping plate (2) are formed as extruded profile rails or rolled profile rails. 

18098


(54) Title of the invention: “DATA ENCRYPTION APPARATUS AND METHOD.” 


H04L 9/08 


(31) Document No.:11-146079 

(32) Date :26/05/1999 


:JAPAN 

(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 




MATSUSHITA ELECTRIC INDUSTRIAL CO. 

LTD., 


1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, 

Japan. 


YOKOTA KAORU 

OHMORI MOTOJI 

MIYAJI ATSUJKO. 

A data converting unit includes a key adding unit for performing an arithmetic addition 

modulo2 32 for input data F and subkey data Ki and outputting the outcome as data G, and a data 

substituting unit for performing an exclusive-OR operation for corresponding bits in data Rot 7 

(G) obtained by shift-rotating the data G by 7 bits toward higher-order bit positions, data Rot 1 

(G)obtained by shift – rotating the data G by 1 bit toward higher order bit positions, and the data 

G itself. 

18099

(21) Application No.IN/PCT/2001/00495/DEL A (22) Date of filing of Application: 11/06/2001 

(54) Title of the invention: “SPECTACLE FRAME ASSEMBLY.” 


G02C 9/04 

(30) Priority Data :PP 7347, 


(32) Date :26/11/1998 


Australia 

(066) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 



Domani Eyewear Pty Ltd. 


3 Wilmette Place, Mona Vale, New South Wales 2103, 

Australia. 


MAUCH, FRANK RICHARD 


A spectacle frame assembly comprises a primary spectacle frame and an auxiliary spectacle frame. 

The primary and secondary spectacle frames each have a pair of rims for receiving a pair of 

lenses, a bridge separating the rims and arms secured to laterally outer portions of each of the 

rims. A primary to each of the auxiliary frame arms. The auxiliary frame lugs are each 

engageable with a corresponding primary frame lug with the auxiliary frame lug disposed on top 

of the primary frame lug so as to secure the auxiliary spectacle frame to the primary spectacle 

frame to the primary spectacle frame. The primary frame lugs are each provided with a magnetic 

member receivable in an open cavity provided in the respective auxiliary frame lug. An 

alternative assembly utilizes rimless primary and auxiliary spectacle primary frame. 

18100


(54) Title of the invention: “A BOOTWIPER MADE OF TWISTED COCONUT FIBER 

RODS”. 


A 47L 023/26 


(31) Document No.:11735 

(32) Date :08/06/1999. 


:SRI LANKA. 

(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 




RILEYS LIMITED, 


53/6, St. Jude’s Mawatha, Mahabage, Sri Lanka. 


MENDIS HILARIAN CHRISHAN SALINDA. 

A Bootwiper made of twisted in brush coconut fibre rods fixed to a galvanized steel outer wire 

frame where the said wire frame is arranged with equally parallel spaced series of plastic/rubber 

separator grids having holes at equal intervals fixed to two opposite sides of the said frame to 

accommodate the brush fibre rods through the said holes at substantially perpendicular to the said 

separators and parallel to the said two opposite sides of the frame to give a pre-determined base 

pattern with two opposite upper and lower faces characterized by three additional twisted in fibre 

rods that are fitted upstanding above one face of the said base placing one at the center and the 

balance two at the extreme ends and fixing two rubber anti slip strips on the opposite face of the 

base directly opposite the two twisted in fibre rods at the extreme ends. 

The base platform made of twisted in brush fibre rods can be designed in rounds, square, 

straight, diagonal, zig zag, octagonal shapes etc.(fig 8-12) by changing the combination of the 

unique plastic/rubber separators & spacer tubing and fixing method of the said twisted in fibre 

rods to the grid. 

18101

(21) Application No.IN/PCT/2001/0000232/DEL A (22) Date of Application: 20/03/2001 

(54) Title of the invention: “ A METAL AND ALLOY TREATMENT METHOD”. 


C 21D 8/06 


(31) Document No.:98117983 

(32) Date :01/10/1998 


RU. 

(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 



GENERAL ELECTRIC COMPANY &INSTITUTE 

FOR METALS SUPERPLASTICITY PROBLEMS 

OF THE RUSSIAN ACADEMY OF SCIENCE, 


One River Road, Schenectady, New York 12345, USA 

&Khalturina Street 39, Ufa. Bashkortostan, 450001, 

Russia. 


UTYASHEV FARID ZAINULLAEVICH 

KAIBYSHEV OSCAR AKRAMOVICH 

VALIAKHMETOV OLEG RAYAZOVICH. 


A metal and alloy treatment method, including deformation of at least a section of a billet through 

reduction of the billet’s cross-section, the method comprises:- 

- providing a long rod-shaped billet 

- reducing the billet’s cross section by moving the billet along and across its axis 

- rolling the billet about it’s surface 

- providing at least one support stand for positioning the billet 

- applying strain at pre specified strain level, wherein the step of applying strain 

comprises deforming the billet, and the step of deforming is selected from applying 

torsion and subjecting the billet to extension forces 

- wherein the stand is capable of deforming the billet at a temperature sufficient to 

provide a microstructure with intrinsic physical and mechanical characteristics. 

18102


(54) Title of the invention: “ AN IMPROVED PROCESS FOR THE PREPARATION OF 

AQUEOUS EMULSION FROM CASHEWNUT SHELL 

LIQUID/CARDANOL BASED RESINS”. 


C09J 18502 

C09F 7/00 



(32) Date : 


(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 





RESEARCH, 


Rafi Marg, New Delhi- 110 001,India. 


CHENNAKKATTU KRISHNA SADASIVAN 

PILLAI 

JANARDANAN NAIR DEVAKIAMMA SUDHA 

VADAKKETHONIPPURATHU SIVANKUTTY NAIR 

–PRASAD 

PADMANABHAN ANAN DAN. 

The present invention relates to a process for the preparation of aqueous emulsion from cashew nut 

shell liquid/cardanol based resins. As the aqueous emulsion of cashew nut shell liquid/cardanol 

resins particularly of their applications as adhesives are in the plywood and lamination sectors. 

The emulsion can substituted phenol-formaldehyde, urea formaldehyde resins used in such 

industries. The process of the present invention has essentially the following steps: reacting 

CNSL/cardanol with phosphorous pentoxide at ambient temperature for 4 hrs. under stirring and 

cooling (the temperature rises due to heat of reaction) it down to 90 0 C when cold water is added 

under stirring followed by the addition of emulsifying agent at room temperature and stirring till 

emulsification is complete. 

18103


(54) Title of the invention: “A PROCESS FOR THE PREPARATION OF NOVEL ALKYL- 

CYCLOALKYL THIOPHENE COPOLYMERS USEFUL FOR 

LIGHT EMITTING DIODE APPLICATIONS.” 


H01L 21/00 

C07D 333/00 



(32) Date : 


(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 




COUNCIL OF SCEINTIFIC AND INDUSTRIAL 

RESEARCH AND TATA INSTITUTE OF 

FUNDAMENTAL RESEARCH, 


Rafi Marg, New Delhi- 110 001 and Homi Bhabha Road, 

Mumbai - 400 005 . 


NARAYANASASTRI SOMANATHAN 

KALATHUR SABDHAM VENGEPURAM 

SRINIVASAN 

THIRUMALACHARI RAMASAMI 

VIBHA RANI 

RAJIV PRAKASH 

KALATHUR SABDHAM VENGEPURAM 

SANTHANAM. 

The present invention provides a process for the preparation of novel alkyl- cyhcloalkl thiophene 

copolymers useful for light emitting diode applications which comprises synthesizing cyclolalkyl 

thiophene and alkyl thiophene by known methods, copolymerising alkyl thiophene and cycloalkyl 

thiophene in a ratio ranging from 1:0.1 to 1:10 in an organic solvent in inert atmosphere in the 

presence of an oxidizing agent in the range of 1-5 moles per mole of monomer mixture at a 

temperature in the range of 0-30 0 C for a period ranging 3-48 hrs; precipitation the copolymer 

formed with non solvent as herein described; extracting the copolymer by known method. The 

copolymer is useful for light emitting diode applications. 

18104

(21) Application No.761 /DEL/ 1997 A (22) Date of filing of Application: 26/03/1997 

(54) Title of the invention: “A POLYMERIZATION APARATUS.” 

(51) International Classification 7 : B01F 7/32, 

B01F 7/32 


(31) Document No.: 074379/1996 

(32) Date: 28/03/1996 







Total No Of Page: 26 

(57) Abstract 


KURARAY CO., LTD. 


1621, Sakazu, Kurashiki-Shi, Okayama-Ken, 

Japan. 


TOSHIO OGATA 

NOBORU IWATA. 

There is provided a mixing apparatus having a mixing vessel which is substantially in the form of a 

cylinder and a agitating element, the agitating element including at least two bars and at least one 

connecting member which connects the bars to each other to form the agitating element such that 

loci of the bars do not essentially coincide with each other when the bars are rotated around an axis 

of the mixing vessel. 

18105

(21) Application No.1782 /DEL/1997 A (22) Date of filing of Application: 27/6/1997 

(54) Title of the invention: “A METHOD OF MAKING AN APTICALLY 

TRANSPARENT CERAMIC ARTICLE.” 

(51) International Classification 7 : C04B 35/10, 

H01J 61/30 



(32) Date: NA 








(57) Abstract 


OSRAM-SYLVANIA INC., 


100Endicott Street, Danvers, MA 01923, 

United States of America 


GEORGE CHIATSING WEI 

ARLENE HECKER 

DAVID GOODMAN 

A method of making an optically transparent ceramic article comprising the steps of: 

-forming, by conventional method, an aqueous slurry of alumina powder comprising alumina, 

magnesia, and zirconia, and yttria; 

-add nitric acid, and aqueous binder and plasticizer, by conventional method. 

-spray-dry the slurry by conventional method. 

-forming an article by use of sintering to yield the following composition, based on the weight 

percentage of about: 

magnesia 0.020% 

zirconia 0.018% 

yttria 0.035% 

alumina balance 

18106


(54) Title of the invention: “UNDERWATER INSTALLATION.” 

(51) International Classification 7 : E21B 7/128, 

E21B 7/132, E21B 43/01, E21B 43/013 


(31) Document No.: 960997 

(32) Date: 12/03/1996 

(33) Name of convention country: NORWAY 







(57) Abstract 


TERJE MAGNUSSEN 


Oksevollveien 24,4500 Mandal, Norway. 


TERJE MAGNUSSEN 

An underwater installation for use in offshore drilling of and production from, respectively, oil and 

/or gas wells at deep and moderate deep water comprises an intermediate station in the form of a 

buoyancy based hollow body (16) tension strut anchored at the seabed (10) and located at a depth 

substantially closer to the surface of the sea than the seabed (10). At least one hydrocarbon 

conveying pipeline extends between the buoyancy body (16) sand seabed depth, for the transfer of 

hydrocarbons from, the reservoir to said buoyancy body (16). At least one casing liner string (18a- 

18h) constitutes the tension leg/strut anchoring of the buoyance body (16). 

18107

(21) Application No1674/DEL/ 1997 A (22) Date of filing of Application 20/06/1997 

(54) Title of the invention: “A DEVICE FOR REMOVING LIQUID FROM A 

MIXTRUE OF LIQUID AND SOLID MATTER.” 

(51) International Classification 7 : B01 D33/04, 

B01 D33/64 


(31) Document No.: 91201199.6, pv1474-91, 

2042833-3, 116088/91, 91-8166 

(32) Date: 17/5/1991, 20/5/1991, 

17/5/1991,21/5/1991, 20/5/1991 

(33) Name of convention country: EP, CZECH, 

CANADA, JAPAN, and S. KOREA. 







(57) Abstract 


PANNEVIS B.V., A DUTCH 

CORPORATION 


24,3542 An Utrecht, The Netherlands. 


ALPHONS ARNOLDUS JOHNNES 

ANTONIUS PRINSSEN 

A device for removing liquid from a mixture of liquid and solid matter, provided with an endless 

conveyor belt (28) which is previous to liquid and with one or more casings (29) over which a 

conveying portion of the conveyor belt (28) moving the mixture during operation is led, whereby 

means are provided for intermittently effecting a relative movement between the casings (29) and 

the conveyor belt (28) and the casing(s) (29) do not move with respect to each other, characterized 

in that a plurality of pressure rollers (9) extending transversely to the direction of movement are 

disposed above a conveying portion of the conveyor belt extending over a casing (29) having a 

fixed position, whilst means are provided by which said pressure rollers (9) can be independently 

pressed down in the direction of the conveying portion and be moved in a direction away from the 

conveying portion. 

18108

(21) Application No.887 /DEL/1997 A (22) Date of filing of Application 07/04/1997 

(54) Title of the invention: “REPLACEABLE SHAVING CARTRIDGE.” 

(51) International Classification 7 : B26B 21/22 


(31) Document No.: 08/630,437 

(32) Date: 10/04/1996 

(33) Name of convention country: USA. 







(57) Abstract 


THE GILLETTE COMPANY 


Prudential Tower Building, Boston, State Of 

Massachusets, USA 


DOMENIC VINCENT APPRILLE, 

Jr., DONALD ROBERT CHAULK 

JOSEPH GEORGE FUCCI 

STEPHEN CABOT METCALF 

ROBERT ANTHONY TROTTA 

CHARLES BRIDGHAM WORRICK 

A shaving system includes a replaceable shaving cartridge and shaving razor handle. The 

replaceable shaving cartridge has a housing carrying blades, a guard, a cap, and a camming 

surface. The cartridge includes an interconnect member having a pivotal support structure that 

pivotally supports the housing and base structure adapted to be removably and fixedly attached to 

the handle. A shaving razor handle has an elongated hand gripping structure and a cartridge 

support structure extending from an end of the hand gripping structure. The cartridge support 

structure has an extension with outer side surfaces that mate with inwardly directed surfaces of a 

recess on the cartridge and an end surface with an opening. The extension has an asymmetrical 

shape to ensure proper orientation. A spring-blased plunger is retained in the cartridge support 

structure and extends through the opening of the cartridge support structure. 

18109

(21) Application No. 1445 /DEL/1997 A (22) Date of filing of Application: 30/05/1997 

(54) Title of the invention: “A COOLING DEVICE FOR COOLING FALSE TWISTED 

YARN.” 

(51) International Classification 7 : D02 G1/02, 

D02 J13/00, D01 H7/46 


(31) Document No.: 8-161131 

(32) Date: 30/5/1996 







Total No Of Page: 24 

(57) Abstract 


TORAY ENGINEERING CO., LTD., A 

JAPANESE CORPORATION 


4-18 Nakanoshima 3-Chome, Kita-Ku, 

Osaka-Shi, Osaka, Japan. 


JUN TAKAGI 

MISAO KASHIWAGI 

NOBUHIRO KOIZUMI 

A cooling device for a false twisting machine having a fixed wall member 16 and movable wall 

members 18a and 18bwhich have faced side surfaces between which yarn treatment 

passageways 19a and 19b are formed. The facing side surfaces are formed with yarn contacting 

portions 16 al and 16b1 and 18a-1 and 18b-1, which are spaced along the direction of the 

running of the yarn in the yarn treatment passageways. The arrangement of the yarn contacting 

portions are such that contact with the yarn occurs alternately between the fixed wall member 16 

and movable wall members 18a and 18b. A sucking duck 14 is opened to the yarn treatment 

passageways 19a and 19b to generate flows of fluid transverse to the running direction of the 

yarn in the passageways 19a and 19b. 

\ 

18110

(21) Application No.1818 /DEL/ 1998 A (22) Date of filing of Application: 29/06/1998 

(54) Title of the invention: “PROCESS FOR PRODUCING PRESSURIZED LIQUID 

RICH INN METHANE FROM A MULTIPLE COMPONENT 

FEED STREAM.” 

(51) International Classification 7 : F25 J3/02, F25J1/00 


(31) Document No.: 60/051.460, 60/087.667 

(32) Date: 01/07/1997, 02/06/1998 







Total No Of Page: 

(57) Abstract 


EXXONMOBIL UPSTREAM 

RESEARCH COMPANY. 


100 West 10 th street, City of 

Washington, County, of New Castle, 



ERIC T. COLE 

EUGENE R. THOMAS 

RONALD R. BOWEN 

This invention relates to a process for producing pressurized liquid rich in methane from a multicomponent 

feed stream containing methane and freezable component having a relative volatility 

less than that of methane. The multi component feed stream is introduced into a separation system 

having a freezing section operating at a pressure above about 1,380 kPa (200psia) and under solids 

forming conditions for the freezable component and a distillation section positioned below the 

freezing section. The separation system produces a vapor stream rich in methane and a liquid 

stream rich in the freezable component. At least a portion of the vapor stream is cooled to produce 

a liquefied stream rich in methane having a temperature above about-112 0 C (-170 0 F) and a 

pressure sufficient for the liquid product to be at or below its bubble point. A first portion of the 

liquefied stream is returned to the separation system to provide refrigeration to the separation 

system. A second portion of the li8quefied stream is withdrawn as a pressurized liquefied product 

stream rich in methane having a temperature above about-112 0 C (-170 0 F). 

18111


(54) Title of the invention: “A TELECOMMUNICATION TERMINAL DEVICE.” 

(51) International Classification 7 : H04 M17/02 


(31) Document No.: 2175/97 

(32) Date: 15/09/1997 

(33) Name of convention country: SWITZERNAD 







(57) Abstract 


SWISSCOM AG., 


21,3052 Bern, Switzerland. 


RUDDLF RITTER 

WALTER HEUTSCHI 

Billing method and billing system to determine usage fees, which are charged to the user of a 

digital telecommunication network, whereby a usage fee charged for a connection is determined 

prior to establishing this connection from statistical characteristics of previous connection of the 

user. 

Preferably, the usage fees are determined from a dynamic client profile stored in a first memory 

area, which profile is derived from one or multiple random variables of previous connections of 

the user of the digital telecommunication network. After new connections of the user, the stored 

client profile is again dynamically derived. 

In a simple variant, the client profile contains a value proportional to the average price per 

connection or to the average duration of a connection of the user. 

In a preferred embodiment, the client profile also contains multidimensional functions of random 

variables of previous connections of the user of the digital telecommunication network. 

The random variables used to derive the client profile include, for example, the connection 

duration, the time of day the day of the week, and /or geographic characteristics of previous 

connections. 

Preferably, the usage fees are also dependent on a statistically derived system load. 

Advantage: for example, in a pre-paid system, the usage fees can be charged already prior to 

establishing the connection. 

18112

(21) Application No. 69 /DEL/ 1997 A (22) Date of filing of Application: 09/01/1997 

(54) Title of the invention: “A THREE DIMENSIONAL SHEET AND A METHOD 

THEREOF.” 

(51) International Classification 7 : B32B 003/00, 

B31F 001/00 


(31) Document No.:08/745,399 

(32) Date: 08/11/1996 








(57) Abstract 


THE PROCTER & GAMBLE COMPANY 


Cincinnai, Ohio 45202, United States Of 

America. 


HAMILTON, PETER WORTHINGTON 

MCGUIRE, KENNETH STEPHEN 

TWEDDELL, RICHARD III 

The present invention relates three-dimensional sheet materials, which resist nesting of 

superimposed layers into one another. More particularly, the present invention provides a threedimensional, 

nesting-resistant sheet material having first side and a second side. The first side 

comprises at least one region having a plurality of spaced three-dimensional protrusions extending 

outwardly from the first side, which are preferably unitarily formed from the sheet material. To 

provide the nesting-resistant advantages of the present invention, the protrusions form an 

amorphous pattern of a plurality of different two-dimensional geometrical shapes. Preferably, the 

second side comprises a plurality of spaced, three-dimensional hollow depressions corresponding 

to the protrusions, such that the protrusions are hollow. Of particular interest for certain 

applications, such as a carrier for an adhesive, the protrusions are separated by an interconnected 

network of three-dimensional spaces between adjacent protrusions. The three-dimensional, nesting 

resistant sheet materials are preferably manufactured in accordance with the present invention 

utilizing a three-dimensional recesses separated by interconnected lands. The recesses form an 

amorphous two-dimensional pattern of interlocking two-dimensional geometrical shapes. The 

amorphous pattern of interlock in shapes is preferably derived from a constrained Voronoi 

tessellation of 2-space in accordance with the present invention, wherein the tessellation is 

constrained by a constraint factor which controls the range of permissible center-to center spacing 

of the interlocking shapes. The manufacture the three-dimensional, nesting-resistant sheet 

materials in accordance with the present invention, a sheet of deformable material is introduced 

onto the forming structure and permanently deformed into compliance with the forming structure. 

If desired, the interconnected lands of the forming structure maybe coated with a substance before 

the sheet of deformable material is introduced onto the forming structure. 

18113

(21) Application No71. /DEL/ 1997 A (22) Date of filing of Application:09/01/1997 

(54) Title of the invention: “STORAGE WRAP MATERIAL.” 

(51) International Classification 7 : B32B 31/00 


(31) Document No.: 08/584,638,08/745,340 

(32) Date: 10/11/1996, 08/11/1996 








(57) Abstract 


THE PROCTER & GAMBLE COMPANY. 


Cincinnai, Ohio 45202, United States Of 

America. 




The present invention relates to sheet-like materials suitable for use in the containment and 

protection of various items, as well as the preservation of perishable materials such as food items. 

More particularly, the present invention provides an improved storage wrap material comprising a 

sheet of material having a first side and a second side. The first side comprises and active side 

exhibiting an adhesion peel force after activation by a user which is greater than an adhesion peel 

force exhibited prior to activation by a user. The storage wrap material may be activated by 

different approaches, but in a preferred embodiment the active side is activatible by an externally 

applied force exerted upon sheet of material. The force may be an externally applied compressive 

forced exerted in a direction substantially normal to the sheet of material. In accordance with the 

present invention, the storage wrap material is selectively activatible by a user in discrete regions 

to provide adhesive properties where and when desired. The use of an adhesive or adhesive-like 

substance on the surface of the material provides an adhesion peel force after activation, which is 

sufficient to form a barrier seal against a target surface at least as great as those of the material and 

the target surface such that perishable items, such as food items, may be effectively preserved. The 

storage wrap materials of the present invention may be utilized to enclose and protect a wide 

variety of items by various methods of application, including direct application to the desired item, 

enclosure of the desired items and securement to itself, and /or in combination with a semienclosed 

container. 

18114

(21) Application No826. /DEL/1997 A (22) Date of filing of Application: 31/03/1997 

(54) Title of the invention: “A BOTTOM SUPPORT FOR BOILER WASTE HEAT 

RECOVERY BOILER (WHRB) INLET GAS 

DUCTING.” 

(51) International Classification 7 : F22B 37/24 



(32) Date: NA 








(57) Abstract 


BHARAT BEABY ELECTRICALS LTD. 


Bhel House, Siri Fort, New Delhi-110049 


PILLARISETTI MEHER LAKSHMI 

PRASAD 

GANESNA VIJAYAKUMAR 

ANANTHA RAJAMANI 

RENGARAJAN ETHIRAJULU 

A bottom support means for Waste Heat Recovery Boiler inlet gas ducting comprising a bottom 

duct supported by means of bottom supporting arrangement, said bottom supporting arrangement 

comprises beam/beams adapted to be connected to the main boiler columns such that to transfer 

the load, a slide bearing plate being secured to said beam at the location where said bottom duct 

being rested 

, a vertical buck stay with a beam being provided to connected the duct wall therewith by means of 

bolts and nuts, said duct wall being connected to a T-bar level bracings through a T-bar stiffeners 

and a plate member secured therewith. 

18115

(21) Application No.1516 /DEL/1997 A (22) Date of filing of Application: 06/06/1997 

(54) Title of the invention: “A PROCESS FOR PREPARING A SOLID TITANIUM 

CATALYST COMPONENT.” 

(51) International Classification 7 : CO7D 301/12 

C07D 301/19, B01J 021/08 


(31) Document No.: 147631/1996 

(32) Date: 10/6/1996 








(57) Abstract 


MITSUI CHEMICALS, INC., 


5-2 Higashi-Shimbashi 1-Chome, Minato- 

Ku, Tokyo, Japan. 


YASUSHI NAKAYAMA 

KAZUMITSU KAWAKITA 

HARUYUKI MAKIO 

SHINICHI KOJOH 

A process for preparing a solid titanium catalyst component for olefin polymerization which 

process comprises the types of contacting a helogen contains magnesium compound in the liquid 

states to contact with a diether compound having a fluorine ring represented by the following 

formula and allowing the resulting solution to contact with a liquid titanium compound. 

(X) m (Y) n 

R a O O R b 

Wherein R a and R b may be the same as or different from each other and are each an alky1 group of 

selected from methy1, ethty1, n-propy1, iso-propy1, n-buty1, iso-buty1, tert-buty1, pen6y1 and 

hexy1; Xand Y may be the same as or different from each other and are each methy1, iso-propy, 

iso-buty1 or chlorine atom, m, is a number of 0 < n < 4; 

18116


(54) Title of the invention: “A PROCESS FOR THE PREPARATION OF IMPROVED 

COATING FROM BHILAWANUT SHELL LIQUID; USEFUL 

FOR THE PROTECTION OF BOMBOOSURFACES.” 

(51) International Classification 7 : C10M137/10, 

CO7C65/00, C09D3/00 



(32) Date: NA 








(57) Abstract 


COUNCIL OF SCIENTIFIC & 

INDUSTRIAL RESEARCH. 


Rafi Marg New Delhi-110001 


MOHINI SAXENA 

SORNA GOWRI 

The present invention provides a process for the preparation of improved surface coating from 

bhilawanut shell liquid useful for the protection of bamboo surfaces, which comprises reacting 

under reflux at a temperature in the range of 80 to 90 0 C for a period in the range of one to one and 

half hours the ingredients comprising of bhilwanut shell Liquid 20 to 40 parts by weight, Phenol 

30 to 60 parts by weight formalin 35 to 70 parts by weight, Catalyst Na OH 2.5 to 5 parts by 

weight, Water 5 to 10 parts by weight and adding 5-6% of Cupric chloride to the refluxed 

composition to get the said surface coating of air drying property. 

18117

(21) Application No.00526/DELNP/ 2004 A (22) Date of filing of Application: 03/03/2004 

(54) Title of the invention: “MEMORY DEVICE ARCHITECTURE.” 

(51) International Classification 7 : G11C 

11/408,11/4097,7/18, 8/14 


(31) Document No.: 09/941,053 

(32) Date: 28/8/2001 




(62) Filed on: NAS 





An apparatus, comprising: 




State Of Delaware, Of 2200 Mission College 

Boulevard, Santa Clara, California 95052, United 

States Of America. 


SHIH-LIEN LU 

DINESH SOMASEKHAR 

VIVEK DE 

A row of memory cells comprising a first memory cell and a second memory cell; 

A set of word-lines coupled to said row and comprising a word-line to select the first memory cell 

independently from the second memory cell; and 

Circuitry to sense a difference between a signal on a first bit-line in response to a charge from the 

first memory cell and reference on a second bit-line coupled to the second bit-line coupled to the 

second memory cell. 

18118


(54) Title of the invention: “INSTALLATION FOR STORING LIQUIFIES GASES.” 

(51) International Classification 7 : F17C 3/04, F17C 3/06 


(31) Document No.: 19984763, 19985502 

(32) Date: 12/10/1998, 25/11/1998 

(33) Name of convention country: NORWAY 









NORCONSULT AS ., 


Vestfjordgaten 4, N-1337 Sandvika, 

Norway. 


HAUG SVEIN MARTIN 

An installation for storing liquified gases in a cavity defined by rock or an outer shell (10) made of 

concrete, comprising a tank (2) for the gas. The tank (2), which is made of concrete and possibly 

thermally insulated, is entirely or partly surrounded by a mass (5) filling a void between the tank (2) 

and the rock or the concrete shell (10). The mass (5) may in itself be sealing, i.e. of low permeability, 

and may be combined with at least one sealing membrane (13) within the mass (5) or outside or inside 

the mass. The installation may be located entirely or partly in loose soil (8), which entirely or partly 

surrounds the shell (10), or be located above ground level. 

18119


(54) Title of the invention: “AN IMPROVED NEEDLE VALUE FOR REFRIGERATING 

DEVICE.” 

(51) International Classification 7 : F25 B-14/06, F16K- 

31/06 


(31) Document No.: 11-130699 

(32) Date: 12/05/1999 










DAIKIN INDUSTRIES, LTD. 


UMEDA CENTER B LDG., 4-12, 

NAKAZAKI-NISHI 2-CHOME, KITA- 

KU, OSAKA 530-8323, JAPAN. 


RYUZABURO YAJIMA 

NOBUO DOMYO 

HAJIME ESUMI 

SHIGEHARU TAIRA 

Formed in a value main body (1) is a refrigerant flow path (41) for lowering the amount of flow of a 

refrigerant which flows into an internal space (30) of a casing (3) from a refrigerant flow path (9) 

through a needle fit/insert clearance (17) defined between a needle fit/ insert aperture (16) and a needle 

(2)inserted into the needle fit/insert aperture(16). When, with the rise or drop in refrigerant pressure, 

refrigerant flows through the needle fit/ insert clearance (17), adhesion of slu8dge included in the 

refrigerant to the wall surface of the needle fit/ insert clearance (17) is reduced by a lessened amount of 

refrigerant flow in the needle fit/ insert clearance (17) by the refrigerant flow path (41). This therefore 

prevents, as far as possible, malfunction of the needle (2) due to sludge adhesion, thereby ensuring 

proper operation of the needle (2). 

18120

(21) Application No. 0092/DELNP/2004 A (22) Date of filing of Application: 13/01/2004 

(54) Title of the invention: “A FLUID CURRENT MOTOR FOR EXTRACTING ENERGY.” 

(51) International Classification 7 : F03D 1/02, FO3D 

11/02 


(31) Document No.:09/881,511, 09/997,499 

(32) Date: 14/06/2001, 23/11/2001 










SELSAM DOUGLAS SPRIGGS 


2600porter Avenue, Unit B, Fullerton, Ca 

92833,Usa. 


SELSAM DOUGLAS SPRIGGS. 

A fluid current motor for exrtacting energy, in the form of shaft rotation capable of driving a load (6) 

from a fluid flow relative to a surface (1), comprising: A resiliently flexible tower/ drive shaft (10) 

having a stiffness, having a basal end (7) and a distal end (9) said tower/drive shaft (10) projecting 

substantially proximate said basal end (7), substantially away from said surface (1); 

A cantilevered bearing means (5) which rotatably supports said tower/drive shaft (10), in a contilevered 

manner, substantially from said basal end (7); a multiplicity of fluid reactive rotors (13,44), coaxially 

attached at spaced intervals to a section of said tower/drive shaft (10); 

Wherein: Said tower/drive shaft (10) is caused by said fluid flow to become sufficiently properly 

oriented to said fluid flow that said rotors (13) are caused by said fluid flow torotate, there by causing 

the tower/drive shaft (10) to rotate, along its entire length, so that useful power in the form of shaft (10) 

rotation is drawn there from, proximate said basal end (7). 

18121


(54) Title of the invention: “METHOD AND APARATUS AUTOMATICALLY CHECKING THE PRINTING 

QUALITY FOR MULTICOLOR IMAGE” 

(51) International Classification 7 : G06K 9/00 


(31) Document No.: MI96A000568 

(32) Date: 22/03/1996 

(33) Name of convention country: ITALY 









DA LA RUE GIORI S.A, A SWISS 

COMPANY 


4, Rue De La Paix, 1003 Lausanne, 

Switzerland. 


DA LA RUE GIORI 

A sheet of paper (1) with the image to be checked passes in front of a camera (3) designed to 

capture three chromatic images and to emit three signals (S1, S2, S3). These signals are introduced 

into a device (4) applying a function F which comprises coefficients (K1, K2, K3, K10, K20, K30) 

previously recorded in a suitable device (2). The single signal (5) resulting from the function F is 

delivered to a device (6) for checking the printing. 

18122


(54) Title of the invention: “A PROCESS FOR THE SYNTHESIS OF NEW GREEN EMITTING Tb 3+ 

ACTIVATED BORATE PHOSPHORS FOR USE IN LOW PRESSURE MERCURY 

VAPOUR LAMPS.” 

(51) International Classification 7 : C09K 11/63 


(31) Document No.:09/26746 

(32) Date: 05/03/1999 










COUNCIL OF SCIENTIFIC AND 



Rafi Marg, New Delhi-110001 


GUNDLAPALLI VENKATA SUBBA 

RAO 

RAMAKRISHAN SANKAR. 

A process for the synthesis of new green emitting Tb 3+ activated borate phosphors having the 

formula A6M1-x TbM 1 (bo3) 6 wherein A=Sr; M=Y, Gd, Al, Ga; and 0.02


(54) Title of the invention: “AN IMPROVED PROCESS FOR THE PREPARATION OF STARCH BASED 

BIODEGRADABLE POLYESTERS.” 

(51) International Classification 7 : C 08L 101/00,3/00, 

29/04, 67/00 



(32) Date: NA 







Total No Of Page: 




INDUSTRIAL RESEARCH 




ANJANIKUMAR JYOTIPRASAD 

VARMA, 

SUJATA PANDURANG KOKANE, 

PARIMAL DESHPANDE, 

AMIT PARADKAR 

NEERU CHOUDHARY. 

An improved process for the preparation of starch based biodegradable polyesters which comprises 

thermally melting and degrading the recycled / degraded polyesters at temperature at 80 to 120 0 C 

above the melting point of the said polyester under constant stiring at a rate of 50 to 200 rpm for a 

period ranging between 10 to 40 minutes, adding starch in the range of 30 to 300%w/w of 

thermally degraded polyesters and keeping the reaction mixture under above mentioned conditions 

for a period of 1 to 10 minutes, and quickly removing the material to obtain the starch based 

polyesters. 



(54) Title of the invention: “SYSTEM AND METHOD FOR PROVIDING RESOURCES FROM A 

WEB SERVER TO A CLIENT COMPUTER.” 

(51) International Classification 7 : G06F 7/00, G06F 

17/30 


(31) Document No.: 09/726,985 

(32) Date: 30/11/2000 







Total No Of Page: 21. 



INTERNATIONAL BUSINESS 

MACHINE CORPORATION. 


Armonk , New York 10504, United States 

Of America. 


MORLITZ DAVID 

An OFFLINE request is sent from the client computer to the web server. The Web server determines 

the Web page specified by the and all the linked (referenced) pages to a depth of . The 

Web server determines all graphics, audio clips, and other resources needed for these Web pages, 

compresses these resources. and creates an archive file containing the compressed resources. 

Alternatively, the Web server selects pre-packaged archive file including these compressed resources. 

The archive file also includes metadata and a site map for the web site. The archive file can later be 

decompressed. The archive file allows the client computer to browse the web site off-line and optimize 

future requests for resources. 

18125

(21) Application No. 0463/ DEL/1999 A (22) Date of filing of Application: 23/03/1999 

(54) Title of the invention: “A PROCESSOR FOR EXECUTING PARTIAL WIDTH PACKED DATA 

INSTRUCTIONS.” 

(51) International Classification 7 : G06 F9/22,G06 F9/302 


(31) Document No.: 09/053,127 

(32) Date: 31/03/1998 














CALIFORNIA 95052, UNITED 

STATES OF AMERICA. 


TICKY THAKKAR 

PATRICE ROUSSEL 

A method and apparatus are provided for executing scalar packed data instructions. According to one 

aspect of the invention, a processor includes a plurality of registers, a register renaming unit coupled to 

the plurality of register, a decoder coupled to the register-renaming unit, and a partial-width execution 

unit coupled to the decoder. The register renaming unit provides an architectural register file to store 

packed data operands each of which include a plurality of data elements. The decoder is configure to 

decode a first and second set of instructions that each specify one or more registers in the architectural 

register file. Each of the instruction in the first set of instructions specify operations to be performed on 

all of the data elements stored in the one or more specified registers. In contrast, each of the 

instructions in the second set of instructions specify operations to be performed on only a subset of the 

data element stored in the one or more specified registers. The partial-width execution unit is 

configured to execute operations specified by either of the first or the second set of instructions. 

18126


(54) Title of the invention: “A PROCESS FOR THE PREPARATION OF ULTRA THIN 

FILMS OF METAL PHTHALOCYANINES.” 

(51) International Classification 7 : C09 B47/04 

C07 D487/22 



(32) Date: NA 















SHIVARAM DATTATRAYA SATHAYE 

KASHINATH RANGU PATIL 

DILIP VINAYAK PARANJAPE 

The present invention relates to an improved process for the preparation of ultrathin films of metal 

phthalocyanines. The thickness of the films prepard by the process of the present invention is in the 

range of 30 to 500 A. The films formed are useful for catalysts, sensors, solar energy conversions etc. 

The various applications of such films could be catalysis for carbon dioxide photoreduction, solar 

energy conversions, imaging technology, electronic devices, etc. 

18127


(54) Title of the invention: “AN IMPROVED PDROCESS FOR THE PREPARATION OF 

ARALKYLATED AROMATIC COMPOUNDS USING 

HETEROGENEOUS CATALYST.” 

(51) International Classification 7 : CO7 

C41/06 

C07 C43/20 

C08G 59/06 

C08G 63/133 



(32) Date: NA 




No.: NA 



NIL 





COUNCIL OF SCIENTIFIC AND INDUSTRJIAL 

RESEARCH. 




Dr. VASANT RAMCHANDRA CHOUDHARY 

SUMAN KUMAR JANA 

B-PHANI KIRAN 

The present invention relates to an improved process for the preparation of aralkylated aromatic 

compounds by catalytic alkylation of aromatic compounds with aromatic alkylating agent using a solid 

catalyst comprising gallium. The process for this invention can be used for the preparation of alkylated 

aromatic compounds, which are fine chemicals and /or used in the preparation of fine chemicals. 

Further, the process utilizes a active solid catalyst that can be reused repeatedly for the catalytic 

reaction. 

18128


(54) Title of the invention: “SYSTEM AND METHOD FOR ENHANCING THE 

DEPENDABILITY OF AN APPLICATION IN A COMPUTING 

SYSTEM.” 

(51) International Classification 7 : G06F-7/64 


(31) Document No.: 09/442,003 

(32) Date: 17/11/1999 










INTERNATIONAL BUSINESS MACHINE 

CORPORATION. 


Armonk, New York 10504 Usa. 


HARPER RICHARD EDWIN 

HUNTER STEVEN WADE 

A method enhancing software dependability, includes measuring elapsed time in a software system 

running on a computer, determining whether the elapsed time matches a threshold, and when the 

elapsed time matches the threshold, rejuvenating at least a portion of the software system to reduce the 

likelihood of an outage and without modifying and application running in the software system. 

18129


(54) Title of the invention: “A SOLID FUEL BURNER AND METHOD THEREOF.” 

(51) International Classification 7 : F23D 

1/00, F23C 11/00 


(31) Document No.: 2000-237235; 

2001-20851; 2001-147964; 

PCT/JP01/06684.. 

(32) Date: 3/08/2001, 4/08/2000, 

29/01/2001, 17/05/2001 


PCT, JAPAN. 



No.: NA 



NIL 





BABCOCK-HITACHI KABUSHIKI KAISHA 


WORLD TRADE CENTER BUILDING 6 th FLOOR 4-1, 

HAMAMATSUCHOU 2-CHOME, MINATOKU, 

TOKYO, 105-6107 JAPAN 


TSUMURA, TOSHIKAZU 

OKAZAKI, HIROFUMI 

SHIMOGORI, MIKI 

KIYAMA, KENJI 

KURAMASHI, KOUJI 

KIKUCHI, HITOSHI 

TAKAHASHI, YOSHITAKA 

MORITA, SHIGEKI 

SAKAI, KAZUHITO 

TANIGUCHI, MASAYUKI 

KOBAYASHI, HIRONOBU. 

According to a burner of the present invention, a stable combustion is obtained in a wide range from a 

high-load operation condition to a low-load operation condition even in the case of low quality solid 

fuel such as brown coal. 

The amount of air supplied from additional air holes or additional air nozzles 12 can be adjusted 

depending on the combustion load of furnace 41. At a low load, the amount of air supplied from 

additional air holes or additional air nozzles 12 is increased, whereby the oxygen concentration in a 

recirculation zones 19 formed downstream of the outside of a fuel nozzle 11 exit, permits a stable 

combustion. At a high load, the amount of air supplied from additional air holes or additional air 

nozzles 12 is reduced, whereby a flame is formed in a position far from the fuel nozzle 11. This 

suppresses thermal radiation onto a solid fuel burner 42 structure and a furnace 41 wall. The solid fuel 

burner 42 is applicable to combustion using low-quality solid fuel such as brown coal and exhaust gas 

as the carrier gas. 

18130


(54) Title of the invention: “UPLINK CHANNEL ASSIGNMENT APPARATUS AND 

METHOD FOR TRANSMITTING AND RECEIVING AN UPLINK 

CHANNEL DATA IS USER EQUIPMENT FOR A CDMA 

COMMUNIATION SYSTEM.” 

(51) International Classification 7 : H04B 1/69 


(31) Document No.: 1999/27166, 

1999/29658,1999/32862,1999/34489, 1999/35058, 

1999/45178, 2000/984,2000/7195, 2000/7166 

(32) Date: 07/7/1999, 21/7/1999, 11/9/1999, 

19/9/1999,23/9/1999,14/10/1999, 

10/01/2000,11/02/2000, 15/02/2000 

(33) Name of convention country: REPUBLIC OF 

KOREA. 









SAMSUNG ELECTRONICS CO., LTD. 


416, MAETAN-DAONG, PALDAL- 

GU, SUWON-SHI, KYONGKI-DO, 

REPUBLIC OF KKOREA. 


MOON, HI-CHAN 

AHN, JAE-MIN 

LEE, HYUN-SEOK 

KANG, HEE-WON 

PARK, SEONG-III 

CHOI, HO-KYU 

HWANG, SUNG-OH 

KOO, CHANG-HOI 

LEE, HYUN-WOO 

CHOI, SUNG-HO 

KIM, JAE-YOEL 

MUN, HYUN-JUNG 

KIM, KYOU-WOONG 

A common packet channel assignment method in a CDMA (Code Division Multiple Access) 

communication system is disclosed. The method comprises transmitting and access preamble signal 

having channel information which is used to access a base station; receiving an access preamble 

acquisition indicator signal received from the base station in response to the access preamble signal; 

transmitting a collision detection preamble for detecting a collision in response to the received access 

preamble acquisition indicator signal; receiving a first signal indicating acquisition of the collision 

detection preamble and a second signal indicating channel assignment, that the base station has 

transmitted in response to the collision acquisition signal; and upon receipt of the first signal; and upon 

receipt of the first signal, allocating a common packet channel according to information designated by 

the second signal. 

18131


(54) Title of the invention: “DATA DISPLAY CONTROL APPARATUS.” 

(51) International Classification 7 : H04 N5/44 


(31) Document No.: 8-240297 

(32) Date: 11/09/1996 










MATSUSHITA ELECRIC INDUSTRIAL 

CO., LTD. 


1006, Oaza Kadoma, Kadoma Shi, Osaka-Fu 

561, Japan. 


MATSUSHITA 

A data display control apparatus receives a digital broadcast and compares the present time with a time 

indicated in a time event part provided in navigation information used to control the display of the 

multimedia data composing a broadcast program. When the indicated time has been reached, the data 

display control apparatus executes instructions to control the display of multimedia data. 

18132

(21) Application No 1106/DEL/2000. A (22) Date of filing of Application: 07/12/2000 

(54) Title of the invention: “A MULTIPLE PARALLEL CATALYTIC REACTOR ASSEMBLY FOR 

CONDUCTING CATALYTIC CHEMICAL REACTIONS AND PROCESS 

THEREOF.” 

(51) International Classification 7 : G01N 31/10, B01J 

19/00,B01J 35/00 


(31) Document No.: 09/464,171, 09/465,213 

(32) Date: 15/12/1999 










UOP LLC, A LTD. LIABILITY 

COMPANY. 


25 East Algonquin Road, Des Plaines, 

Illinois 60017-5017, United States Of 

America. 


IVAR M. DAHL 

ARNE KARLSSON 

DUNCAN E. AKPORIAYE 

RUNE WENDELBO 

KURT M. VANDEN BUSSCHE 

GAVIN P. TOWLER 

A reactor for conducting catalytic chemical reactions has been developed. The reactor has a well 

having an open end and a closed end. The reactor also has a sleeve having a top end and a bottom end. 

The bottom end of the sleeve is inserted within the open end of the well. A fluid permeable structure is 

attached to the sleeve spanning the cross-section thereby defining a chamber between the closed end of 

the well and the fluid permeable structure. The reactor also has a reactor insert having a fluid 

permeable end and a top end containing a first and a second fluid conduit. The fluid permeable end of 

the reactor is inserted within the open end of the sleeve. The first fluid conduit is in fluid 

communication with the chamber, and the second fluid conduit is in fluid communication with the fluid 

permeable end of the reactor insert. 

18133

(21) Application No.00526/DELNP/ 2004 A (22) Date of filing of Application: 03/03/2004 

(54) Title of the invention: “MEMORY DEVICE ARCHITECTURE.” 

(51) International Classification 7 : G11C 

11/408,11/4097,7/18, 8/14 


(31) Document No.: 09/941,053 

(32) Date: 28/8/2001 












State Of Delaware, Of 2200 Mission College 

Boulevard, Santa Clara, California 95052, United 

States Of America. 


SHIH-LIEN LU 

DINESH SOMASEKHAR 

VIVEK DE 

An apparatus, comprising: 

A row of memory cells comprising a first memory cell and a second memory cell; 

A set of word-lines coupled to said row and comprising a word-line to select the first memory cell 

independently from the second memory cell; and Circuitry to sense a difference between a signal 

on a first bit-line in response to a charge from the first memory cell and reference on a second bitline 

coupled to the second bit-line coupled to the second memory cell. 

18134

(21) Application No.0052DEL/1999 A (22) Date of filing of Application: 12/01/1999 

(54) Title of the invention: “A PROCESS FOR THE SYNTHESIS OF NEW BLUE EMITTING Ce 3+ 

ACTIVATED BORATE PHOSPHORS FOR USE IN FLUORESCENT LAMPS 

AND TV TUBES.” 

(51) International Classification 7 : C09K 11/63, 

C09K 11/71, C09K 11/70 


(31) Document No.: 09/273487 

(32) Date: 22/03/1999 










COUNCIL OF SCIENTIFIC & 





GUNDLAAPALI VENKATA SUBA RAO 

RAMAKRISHAN SANKAR 

A process for the synthesis of new blue emitting Ce 3+ activated borate phoshors for use in fluorescent 

lamps and TV tubes, having the formula A6M1-χCeχM 1 (BO3) 6 wherein A=La, Sr; M=La, Y, Gd Lu; and 

M1Mg, Al, Ga, and x ranging from 0.001-1 and the said synthesis is carried out by the solid state 

reaction using at least four of the ingredients from the group consisting of SrCO3 (5.5-6.5mole) La2O3 or 

Gd2O3 Mgo (0.001-1.0 mole), MgO (0.85-1.1 mole) [or Al (NO3) 39H2O], CeO2 (0.001-1.1 mole), and 

H3 BO3 (5.5-6.5mole) comprising the followings steps: (i) mixing and grinding of the ingredients 

selected in suitable proportions, for about 15-45 minutes in an agate mortar with acetone, (ii)subjecting 

the ground ingredients to a pre-firing in air at temperatures ranging from 150-300 0 C for a period of time 

ranging from 2-10 hr. and (iii) subjecting the pre-heated powders obtained from step (ii) to a final heat 

treatment under reducing atmosphere at temperatures ranging from 750-1050 0 C for a period ranging 

from 6-30 hours, to obtain the desired phosphors useful as blue components in low pressure mercury 

vapour lamps, deluxe lamps and in television tubes, when excited with UV radiation of wavelength 254 

and 355 nm. 

18135


(54) Title of the invention: “A SYSTEM FOR DATA TRANSFER AND BUS 

MANAGEMENT OVER A BUS STRUCTURE.” 

(51) International Classification 7 : G06F 13/36 


(31) Document No.: 08/594,651 

(32) Date: 02/02/1996 








(57) Abstract 


SONY ELECTRONICS,INC., 


Sony Drive, Park Ridge, New Jersey 07656- 

8003, United States Of America. 


SCOTT D. SMYERS 

BRUCE FAIRMAN; 

An application programming interface implements and manages isochronous and asynchronous 

data transfer operations between an application and a bus structure. During an asynchronous 

transfer the API includes the ability to transfer any amount of data between one or more local data 

buffers within the application and a range of addresses over the bus structure using one or more 

asynchronous transactions. An automatic transaction generator may be used to automatically 

generate the transactions necessary to complete the data transfer. The API also includes the ability 

to transfer data between the application and another node on the bus structure isochronously over a 

dedicated channel. During an isochronous data transfer, a buffer management scheme is used to 

management scheme is used to manage a linked list of data buffer descriptors. This linked 

descriptor list can form a circular list of buffers and include a forward pointer to the next buffer in 

the list and a backward pointer to the previous buffer in the list for each buffer. The linked 

descriptor list may also form a linear list to which the application can append additional buffers or 

remove existing buffers from the list. During insochronous transfers of data, the API provides 

implementation of a resynchronization event in the stream of data allowing for 

resynchronizationby the application to a specific point within the data. Implementation is also 

provided for a call back routine for each buffer in the list, which calls the application at a 

predetermined point during the transfer of data. 

18136

(21) Application No.225/DEL/ 1997 A (22) Date of filing of Application: 29/01/1997 

(54) Title of the invention: “A RECEIVER AND TRANSMITTER FOR 

RECEIVING AND TRANSMITTING 

INFORMATION IN A SPREAD SPECTRUM 

SIGNAL.” 

(51) International Classification 7 : H04B 1/707 


(31) Document No.: 08/593,758, 08/606,906 

(32) Date: 29/01/1996, 26/02/1996 










MOTOROLA, INC., 


State Of Delaware, United States Of America, 

Of 1303 East Algonquin Road, Schaumburg, 

Illinois 60196. United States Of America. 


ANDREW MURRAY SLONNEGER 

Marco Antonio Mayor 

Carl Myron Willis 

An apparatus at a transmitter (800) initializes (902) pseudonoizes (PN) sequence generators 

(302,306,320) to a predetermined initial state and thereafter generates (906) time-synchronixed PN 

sequences. A spread spectrum signal is then transmitted (908) by utilizing the PN sequences to 

encode information. At a receiver (600,700) a predetermined one of the PN sequences is acquired 

and tracked (1002), and the predetermined one of the PN sequences is acquired and tracked (1004). 

A PN sequence generator (602,714,772,730) of the receiver is adjusted (1006,1014) to generate a 

selected PN sequence time-synchronized with the predetermined one, and a corresponding one of 

the PN sequences is despread (1008) by utilizing the selected PN sequence to decode the 

information. 

18137

(21) Application No. 1684/DEL/1998 A (22) Date of filing of Application: 18/06/1998 

(54) Title of the invention: “An Apparatus Useful For Measuring Particle Size of A Powder Sample” 


G01N 15/02 


(31) Document No.:NIL 

(32) Date : NIL 

(33) Name of convention country : NIL 

(66) Filed U/s 5(2) : NIL 

(61) Patent of addition to application No. : 

NA 


(63) Divisional to Application No. :NIL 


Total Pages: 12 



C.S.I.R 


Rafi Marg New Delhi–110001 


PRADEEP KUMAR GHOSH; 

Apparatus useful for measuring particle size of a powder sample comprises a light source (3), 

having a collimating lens (4) in front of it in such a manner so as to effect parallelism of the light 

beam, an infra red filter (5) being fixed in front of the said lens (4) in such a manner so as to enable 

absorption of the infra red and impinge the said light beam on to a sample (2) being contained in a 

transparent settling column (1), an optical detector (6) being fixed in a manner so as to detect and 

feed the light signal so received through the said sample to an amplifier circuit (7) to record the 

output, the said entire assembly being housed in a light proof box(8). 

18138


(54) Title of the invention: “METHOD OF AND APPARATUS FOR FORMING A JOINT IN AN 

ELONGATE HANDRAIL” 


B29C 65/18 





(66) Filed U/s 5(2) : NIL 


NA 







RONALD HAROLD BALL, 


1083, Beaufort Avenue, Oshawa Ontario LIG 

1G8, Canada, 


DOUGLAS J. WEATHERALL; 

ANDREW O. KENNY; 

RONALD H. BALL; 

A. STUART CAUNCE; 

DAVID S. BALL; 

A method and apparatus are provided for forming a joint in an elongate article formed from 

a thermoplastic material, for example an escalator handrail or a conveyor belt, which also includes 

a plurality of reinforcing cables and a slider fabric. End parts of the article are held in a mold and 

heated to remelt the material. Portions adjacent the end parts are chilled, at ends of the mold, to 

prevent remelting. The molten end parts then fuse, and the molten joint is then cooled to resolidify 

the material and form the joint. With reinforcing cables being present, these can be cut into an 

interlace pattern, which advantageously is provided in just a layer of the article rather than 

extending through the full depth of the article. A top layer can then be replaced by a separate top 

cap of the material of the body of the article, where a slider is present, to provide an effective 

interlacing effect, a bottom layer or portion of a handrail is cut at an inclined angle, to form an 

inclined joint in the slider . 

18139


(54) Title of the invention: “A DEVICE FOR REGULATING THE POSITION OF A STEERING 

BAR OF A TWO–WHEELED OR THREE–WHEELED VEHICLE” 


B61F 3/08 


(31) Document No.:MI99A 000821 

(32) Date : 20/04/1999 

(33) Name of convention country : Italy 

(66) Filed U/s 5(2) : NIL 


NA 







PIAGGIO & C. S.P.A. 


25, Pontedera, Pisa, Italy 


GIUSEPPE PEDANI; 

ALESSANDRO ROTTA; 

A device for regulating the position of a steering bar in two–wheeled or three–wheeled 

vehicle with respect to a steering column (13), comprising a support (18) for a steering bar (19) 

pinned (at 34) with respect to an extension (15) of the steering column (13), between a support 

(18) for a steering bar (19) and an extension (15) of the steering column (13), which provides for 

certain devices (14, 16, 17, 20) allowing a predetermined rotation of the support (18) for the 

steering for the steering bar (19) with respect to the extension (15) of the steering column (13) in a 

plane essentially corresponding to the direction of forward motion of the vehicle. In particular, 

thers devices comprise on one hand a toothed sector (14) and on the other hand a worm screw (16) 

engaging with each other and fermly attached, one to the extension (15) and the other to the 

support (18) for the steering bar (19). The device also provides for a hand–wheel (20) to allow a 

manual rotation. 

18140


(54) Title of the invention: “A PINCH ROLL UNIT AND A METHOD FOR CONTROLLING THE 

OPERATION OF PINCH ROLLS.” 


B21B 39/00 


(31) Document No.:10/365,589 

(32) Date : 12/02/2003 


(66) Filed U/s 5(2) : NIL 


NA 




Total No of Pages: 17 


MORGAN CONSTRUCTION COMPANY; 


15 Belmont Street, Worcester, Massachusetts 

01605, United States Of America. 


TERRANCE MICHAEL SHORE; 

PAUL BARRY RICHES; 

YUN LING; 

MELICHER PUCHOVSKY; 


A pinch roll unit for either propelling or retarding a product moving along the pass line of 

a rolling mill comprises a pair of levers mounted for rotation about parallel first axes. Roll shafts 

are carried by the levers with each roll shaft being journalled for rotation about a second axis 

parallel to the first axis of its respective lever. Pinch rolls are carried by the roll shafts and are 

positioned to define a gap there between for receiving the product. An electrically powered first 

motor operates via a linkage to rotate the levers about the first axes and to move the pinch rolls 

between open positions spaced from the product, and closed positions contacting and gripping the 

product there between. An electrically powered second motor rotatably drives the pinch rolls. 

18141


(54) Title of the invention: “A PROCESS FOR THE PREPARATION OF METAL PHENOLATE” 

(51) International Classification 7 :C07C39/235 


(31) Document No.:09/676,845 

(32) Date : 29/09/2000 


(66) Filed U/s 5(2) : NIL 

(61) Patent of addition to application No. NA 






CROMPTON CORPORATION 


199, Benson Road, Middlebury, Connecticut 

06749, United States of America, 


WILLIAM PALMER ENLOW; 

GARY VINCENT MARLIN 


A process for the preparation of a metal phenolate comprising: 

a) reacting a phenol having the formula: 

wherein each R 1 , R 2 , and R 3 is independently selected from the group consisting of 

hydrogen, methyl, ethyl, n–propyl, iso–propyl, n–butyl, t–butyl, t–amyl, t–hexyl, cyclohexyl, 

cumyl, t–pentyl, and t–octyl with a metal alcoholate having the formula (R 4 O)xQ where R 4 is a 

monovalent organic radical, R 4 O is derived from [the] a corresponding alcohol R 4 OH, and Q is a 

metal cation having a valence X to produce a metal phenolate and an alcohol R 4 OH wherein said 

metal phenolate has the formula: 

(R1 

R1 

R2 

R3 

wherein Q, x, and each R 1 , R 2 , R 3 are as previously defined; and reacting optionally in the 

presence of a solvent; 

b) removing the alcohol R 4 OH from the metal phenolate 

R2 

R3 

OH 

O)x Q 

18142

(21) Application No. 473/DEL/1999 A (22) Date of filing of Application: 24/03/1999 

(54) Title of the invention: “METHOD OF REDUCING MICROPITTING OF A METAL SURFACE” 


C10M 149/00; C10NM 30/06 




(33) Name of convention country :NIL 

(66) Filed U/s 5(2) : NIL 







ETHYL PETROLEUM ADDITIVES 

LIMITED 


London Road, Berkshire RG 12 2UW, Bracknell, 

England. 


HELEN T. RYAN; 

RODNEY I. BARBER; 

CRAIG R. PATERSON; 

Method of reducing micropitting of a metal surface using at least one friction modifier to reduce 

micropitting of a metal surface, which comprises lubricating the metal surface with a lubricant 

composition comprising the at least one friction modifier is used in an amount of 0.125 to 1.0% by 

weiht based on the total weight of the lubricant composition where the at least one friction 

modifier is selected from at least one of 

(a) an O, O–di–(primary alkyl) acyclic hydrocarbyl phosphonate in which the primary alkyl 

groups are the same or different each independently containing 1 to 4 carbon atoms and in 

which the acyclic hydrocarbyl group bonded to the phosphorus atom contains 12 to 24 

carbon atoms and is a linear hydrocarbyl group free of acetylenic unsaturation; 

(b) a dihydrocarbyl hydrogen phosphite in which the hydrocarbyl groups are the same or 

different linear aliphatic hydrocarbyl groups free of acetylenic unsaturation each 

independently containing 8 to 24 carbon atoms, or an amine salt thereof; 

(c) a succinimide of formula: 

18143


(54) Title of the invention: “A Method For Carrying Out Combustion And A Nozzle Aparatus & 

Burner For Carrying Out The Said Method.” 


F23D 14/32 





(66) Filed U/s 5(2) : NIL 








PRAXAIR TECHNOLOGY, INC.; 


39 Old Ridgebury Road, Danbury, State of 

Connecticut 06810–5113, United States Of 

America. 


WILLIAM JOHNSON SNYDER; 

ARTHUR WELLINGTON FRANCIS JR.; 

A method for carrying out combustion, wherein a combustion zone containing furnace 

gases at a temperature exceeding 1000 degrees F is provided, and oxidant and fuel are injected 

through nozzles into the combustion zone and are combusted in the combustion zone, 

a wide oxidant layer is injected through a first refractory nozzle having a pllurality of first orifices 

at a velocity of less than 180 ft / sec to produce a planar oxidant layer in the combustion zone, 

a wide fuel layer is injected through a second refractory nozzle having a plurality of second 

orifices, the fuel being injected at a velocity of less than 210 ft / sec in plane parallel to the plane of 

the oxidant layer in the combustion zone, and oxidant from the oxidant layer and fuel from the fuel 

layer are turbulently mixed within the combustion zone to produce an oxidant–fuel mixture which 

is combusted. 

18144


(54) Title of the invention: “A Locking Mechanism For An Air Handling Duct” 


F16L 35/00 


(31) Document No.:09/904,673 

(32) Date : 13/07/2001 


(66) Filed U/s 5(2) : NIL 








CARRIER CORPORATION, 


Carrier Parkway P.O. Box 4800, Syracuse, New 

York 13221, U.S.A. 


HERBECK Christain charles; 

AUSTIN Michael Wayne; 

JOHNSON Walter Allen; 

RUHL Timothy E.; 

HOCH Peter Johan; 

A locking mechanism for an air handling duct which includes a plurality of 

interconnected modules which together made up the duct. The locking mechanism includes a male 

retainer contained on a frame member of a first module, with the male retainer having a locking 

arm adapted to be moved from an unlocked position to a locked position. A complementary female 

retainer is contained on a frame member of a second module, with the female retainer being in the 

from of an elongated keyway designed to receive and hold the locking arm in a locked position. 

Means are provided to move the arm from an unlocked position to a locked position when the male 

and female retainers are in alignment for locking the modules together. 

18145


(54) Title of the invention: “System For Determining The Complexity Of A Computer Program” 


G06F 9/44, G06F 9/45 


(31) Document No.:09/644,119 

(32) Date : 23/08/2000 


(66) Filed U/s 5(2) : NIL 


NA 







International Business Machine Corporation, 


Armonk, New York 10504, U.S.A. 


BERA Rajendra Kumar, 

Acomputing system for determining the complexity of a computer program; said system 

comprising of a micro processor based central processing unit (4), a hard disk device (5) and 

random access memory (6) wherein said memory incorporates 

means for inspecting the program to identify occurrences therein of predetermined 

program items that are indicative of breaks in the ongoing forward flow of the program; 

means for assigning and recording a pre–determined numeric value to each said items; 

means for summing the assigned numeric values to define a complexity index indicative 

of the complexity of the program. 

18146


(54) Title of the invention: “Stacked Poly–Poly And Mos Capacitor” 


H01L 21/8249, H01L 21/20 


(31) Document No.:09/551,168 

(32) Date : 17/04/2000 

(33) Name of convention country :U.S.A. 

(66) Filed U/s 5(2) : NIL 


NA 







International Business Machines Corporation, 


Armonk, New York, 10504, U.S.A. 


COOLBAUGH Douglas D; 

DUNN James Stuart; 

ST. ONGE Stephen Arthur; 

A stacked poly–poly / MOS capacitor useful as a component in a BiCMOS device 

comprising a semiconductor substrate having a region of a first conductivity–type formed in a 

surface thereof; a gate oxide formed on said semiconductor substrate overlaying said region of first 

conductivity–type; a first polysilicon layer formed on at least said gate oxide layer, said first 

polysilicon layer being doped with an N or P–type dopant; a dielectric layer formed on said first 

polysilicon layer; and a second polysilicon layer formed on said dielactric layer, said second 

polysilicon layer being doped with the same or different dopant as the first polysilicon layer. 

18147

(21) Application No. IN/PCT/2002/567/DEL A (22) Date of filing of Application: 03/06/2002 

(54) Title of the invention: “A PROTOCOL IMPLEMENTRY DEVICE FOR TRANSMITTING 

MULTIMEDIA DATA IN MOBILE COMMUNICATION SYSTEM .” 


H04L 29/10 



2000–61721, 2000–61911, 2000–61914 

(32) Date : 19 & 20, Oct 2000 


Republic of Korea 

(66) Filed U/s 5(2) : NIL 


NA 






SAMSUNG ELECTRONIC CO. LTD., 


416,Maetan–dong, Paldal–gu, Suwon–shi, 442– 

370 Kyungki–do, Republic of Korea, 


KOO,Chang–Hoi; 

KIM, Min–Koo; 

KIM, Dae–Gyun; 

PARK, Dong–Seek; 


There is provided a novel architecture for transmitting multimedia data with different 

QoSs in a mobile communication system. In a protocol structure according to the present 

invention, an RLPlayer receives data with different QoSs and dividing the data into datagrams 

according to the QoSs, a MUX layer multiplexes the datagrams received from the RPL layer and 

outputs multiplexed TU data, and a QCCH receives the multiplexed TU data and outputs TU 

blocks with the QoSs by puncturing and repeating information added according to the QoSs for the 

multiplexed TU data. 

18148


(54) Title of the invention: “HIGH TRACTION AND WEAR RESISTANT ELASTOMERIC 

COMPOSITIONS.” 


C08L 9/00 


(31) Document No.: 60/277,124 

(32) Date : 19.03.2001 


(66) Filed U/s 5(2) : NIL 


NA 






EXXONMOBIL CHEMICAL PATENTS 

INC., 


5200 Bayway Drive, Baytown, Texas 77520– 

2101, United States of America 


WALTER H. WADDELL; 

ROBERT R. POULTER; 

The present invention is an elastoneric composition having a primary rubber 

component, and an elastomeric comonent. More particularly, in one embodiment the elastomeric 

composition has from 50 to 95 phr natural rubber as the primary rubber component, from 5 to 40 

phr of a copolymer of a C4 to C7 isoolefin and a para–alkylstyrene as the elastomeric component, 

and from 0 th 40 phr of polybutadiene as a secondary rubber component. In one embodiment, the 

copolymer includes a terpolymer of isobutylene, para–methylstyrene and para– 

bromomethylstyrene, wherein the parabromomethylstyrene is present from 0.2 mol % to 3.0 mol% 

. Further, the composition desirably contains carbon black. The compositions are useful for tire 

treads and tire sidewalls having improved winter wear properties such as high DIN abrasion values 

and improved Tangent Delta values. The compositions are also useful in any application where 

high damping and high abrasion resistance is desirable, such as in hoses, belts antivibrational 

mounts and shoe soles. 

18149


(54) Title of the invention: “A BODY WASH COMPOSITION.” 


A61K 007/48, A61K 007/50 


(31) Document No.: 08/531,712 

(32) Date : 21.09.1995 


(66) Filed U/s 5(2) : NIL 

(61) Patent of addition to application No. : NA 






HELENE CURTIS, INC., 


325 North Wells Street, Chicago, Illinois 60610– 

4713, United State of America. 


ANTHONY A. Scafidi. 

A body wash composition containing an anionic cleansing surfactant, such as an alkyl ether 

sulfate or an alkyl sulffate, like sodium lauryl ether sulfate or sodium, lauryl sulfate; a polymeric 

cationic conditioning compound, such as a quaternized guar gum; and a quaternized phosphate 

ester in an aqueous carrier is disclosed. The composition is used in a method to cleanse the skin 

and to impart conditioning properties to the skin. 

18150


(54) Title of the invention: “SYSTEM FOR GENERATING MOBILE OBJECTS IN A NETWORK.” 


G06F 9/06 


(31) Document No.: 10–15817 

(32) Date : 07.11.1997, 

(33) Name of convention country : JAPAN 

(66) Filed U/s 5(2) : NIL 


NA 









Kazuhiro Manami; 

Toshihiro Suzuki; 


A system wherein provides various GUI moderator templates symbolizing templates which 

is capable of classifying a complicated behavior of the mobile agent into basic behavior patterns 

and defining a desired behavior pattern of the mobile agent by a combination of the basic behavior 

patterns, and various GUI activities symbolizing an activity of issuing a request in each place 

where the mobile agent moves around. The operator dreps the GUI moderator template and the 

GUI activity on the GUI builder to jion them for defining the order of executing jobs. The user can 

also set address information of a place of execution in the GUI activity. 

18151


(54) Title of the invention: “A HIGH SPEED EMBOSSING AND ADHESIVE APPLICATION 

PROCESS” 

(51) International Classification 7 : B05D 


(31) Document No.:09/289,222 

(32) Date : 09/04/1999 


(66) Filed U/s 5(2) : NIL 


NA 






steps of: 


THE PROCTER & GAMBLE COMPANY, 


One Procter & Gamble Plaza, Cincinnati, Ohio 

45202, United State of America 


MCGUIRE, KENNETH STEPHEN; 

BUSH, STEPHAN GARY; 

A high speed embossing and adhesive application process said process comprising the 

(a) applying adhesive to a conformable heated glue application roll; 

(b) transforming said adhesive from said glue application roll to a first patterned 

embossing roll which is engaged with a second patterned embossing roll having a 

complementary pattern to said first embossing roll; 

(c) passing a web of sheet material between said first and second embossing rolls at a 

tangential line speed to simultaneously emboss said web and apply said adhesive to 

said web, such that said adhesive forms an adhesive pattern between embossments. 

18152


(54) Title of the invention: “Method For Producing Synchronous Drive Belts Having Teeth.” 


B29D 29/08, F16G 1/28 





(66) Filed U/s 5(2) : NIL 


NA 







The Goodyear Tire & Rubber Company; 


1144 East Market Street, Akron, Ohio 44316– 

0001, United States America. 


Michael Johan William Gregg; 

A method of producing synchronous belts having two or more tracks of teeth txtending 

obliquely from the belt. The method includes forming an internal drum mold from a series of 

concentric rings, building a belt sleeve around the drum mold, vulcanizing the blet assembly 

cutting the belt sleeve into widths and removing drum rings from the belt sections. 

46 

42 

48 

32 30 

47 

36 38 

40 

18153


(54) Title of the invention: “OPTICAL FIBER PREFORM HAVING OH BARRIER AND 

FABRICATION METHOD THEREOF.” 


G02B 6/22 


(31) Document No.:1999–2696 

(32) Date : 28/01/1999 



(66) Filed U/s 5(2) : NIL 


NA 







SAMSUNG ELECTRONIC CO., LTD., 


416,Maetan–dong, Paldal–gu, Suwon–shi, 442– 

370 Kyungki–do, Republic of Korea, 


OH, Sung–Koog; 

SED, Man–Seok 

An optical fiber preform and a fabrication method thereof. In the present invention, an 

outer OH–barrier free of P2O5 are deposited respectively between a substrate tube and a cladding 

layer and between the cladding layer and a core layer during a deposition process. In addition, a 

refractive index increases toward the center in the core layer. 

18154


(54) Title of the invention: “A PROCESS FOR MAKING SILICON CARBIDE KILN FURNITURE.” 



(31) Document No.:NA 

(32) Date : NA 

(33) Name of convention country : NA 

(66) Filed U/s 5(2) : NIL 


NA 






CSIR 


Rafi marg, New Delhi–110001 


SANKAR GHATAK; 

KAJAL KUMAR DHARGUPTA; 


A process for making silicon carbide kiln furniture which comprises mixing silicon 

carbide powder of different grit sizes (range of 60 grit to 1200 grit) with 3 to 10 wt % of additive 

cement containing 70 % AL2O3, 25 % SiO2 and 5 % CaO, adding stablising agent and a setting 

agent such as herein described, in an amount in the range of 0.1 to 1.0 wt % to the said mixture of 

silicon carbide and additive cement, adding not more than 1.5 wt % of water to the said mixture to 

form a slurry, wet casting the resultant mixture by conventional method, followed by aging, 

curing, washing and drying the said wet cast, firing the resultant dried product under ambient 

atmosphere at a temperature in the range of 1350 0 to 1450 0 C to obtain silicon carbide kiln 

furniture. 

18155


(54) Title of the invention: “A Process For The Preparation of pH Sensitive, Mucoadhesive Hydrogel 

Nanoparticles for Systemic Delivery of Water Soluble Drugs Through 

Oral Route” 


A61K 009/14; A61K 9/16; A61K47/32; 

A61K 9/51; A61K 9/54 





(66) Filed U/s 5(2) : NIL 


NA 







University of Delhi, 


Department of Chemistry, Delhi–110007, 


Prof. MAITRA,Amarnath; 

MOZUMDAR, Sobho; 

MITRA, Susmita; 

BHARALI, Dhruba Jyoti; 

This invention relates to a process for the preparation of pH sensitive, mucoadhesive, 

hydrogel nanoparticles for the systemic delivery of water soluble drugs through oral routes 

comprising mainly the steps of: 

Step 1 –dissolving a surfactant in oil to obtain reverse micelles, 

Step 2 –adding an aqueous solution of vinyl pyrrolidone (VP), n–isopropyl acrylamide 

(NIPAAM) and acrylic acid (AA) monomers in the molar ratio of 40:30:30 

(VP:NIPAAM:AA), a cross–linking agent, initiator, activator and water to said reverse 

micelles to form an optically clear and transparent reverse micellar solution, 

Step 3 –subjecting said solution to polymerization in the presentce of an inert gas to obtain 

nanoparticles having uniform size between 10 mm to 50 mm diameter with low 

polydispersity, 

18156


(54) Title of the invention: “A Data Processing System For Targeting Advertising To A Multimedia 

System.” 



(31) Document No.:09/409,601 

(32) Date : 30/09/1999 


(66) Filed U/s 5(2) : NIL 


NA 










BASSETT Ronald W; 

BEADLE Bruce A.; 

BROWN Michael Wayne; 

DOUD Leon P.; 

PAOLINI Michael A.; 


The present invention relates to a data processing system for targeting advertising system 

to a multimedia system, said system comprising: first selecting means (514), responsive to 

receiving user input from multimedia system, for selecting respective video streams and audio 

streams from a set of video streams and a set of audio streams that are provided for alternate 

presentations of the event, wherein at least one of the set of video streams and the set of audio 

streams comprises a plurality of streams from which to select, and wherein the selected video 

streams and audio streams are formed; second selecting means (514) for selecting an advertisement 

from a set of advertisements based on the selected video streams and the selected audio streams to 

form a selected advertisement; and sending means (510) for sending the selected advertisement to 

the multimedia system. 

18157


(54) Title of the invention: “ELECTRONIC PACKAGE AND METHOD OF FORMING 

ELECTRONIC PACKAGE.” 


H01L 23/48, H01L23/12 


(31) Document No.: 09/471,679 

(32) Date : 23.12.1999 

(33) Name of convention country : U.S.A.. 

(66) Filed U/s 5(2) : NIL 


NA 






International Business Machine Corporation; 


Company Organized and Existing Under The 

Law of NEW YORK, United States Of America, 

Of Armonk, New York 10504, U.S.A. 


BRODSKY William L; 

SATHE Sanjeev B.; 

THIEL George H.; 

A semiconductor chip package having a non–planar chip therein, to reduce the stress 

concentrations between the chip and cover plate. In particular, a chip and method of forming a chip 

having a non–planar of “domed” back surface, wherein the thickness of the non–planar chip is 

greatest substantially near the center of the chip. Further, a method of rounding the edges or 

corners of the chip to reduce crack propagation originating at the edges of the chip. 

18158


(54) Title of the invention: METHOD AND SYSTEM FOR CONTROLLING ACCESS TO DATA IN 

SHARED DISK PARALLEL DATA FILE 


G06F 17/30 


(31) Document No.:09/737,393 

(32) Date : 15/12/2000 


(66) Filed U/s 5(2) : NIL 


NA 









Armonk, New York 10504 U.S.A. 


WANG–KNOP Kuei–Yu; 

CURRAN Robert Johan; 

KANDANAI Radha Rani; 

The system for controlling access to data in a shared disk parallel data file comprising 

means (6.1, 6.8, 6.3) to determine communication failure to one node in a two node system, means 

(6.1, 6.8) to determine whether said failed node has been enabled for a single node quorum 

operation, and means (6.1, 6.8, 6.5) to fence data access from said failed node, upon detection of a 

single node enabled status. 

The system is provided for continuing node operations in quorum–based protocls. This is 

particulary valuable in the situation in which a group of nodes comprises only two nodes and in 

which communications to a node is lost. Provision is made for adding additional status indications 

to each node indicating whether or not it is enabled for single–node quorum operation. Provision is 

also made for identifying one node as a primary node and another node as a secondary node for 

time–out response purposes. 

18159


(54) Title of the invention: “A VALVE FOR CONTROLLING A HIGH PRESSURE AND FLOW 

RATE OF WORKING FLUID IN PIPELINES”. 

(51) International Classification 7 : F16K 3/24 


(31) Document No.:2001115576 


(33) Name of convention country : RU 

(66) Filed U/s 5(2) : NIL 


NA 







MALINA, 


35–77, Moscow, 127322 (RU) 


MALINA 

KURLOV 

The valve for controlling a high pressure and flow rate of working fluid in pipelines 

comprising a body (1) provided with inlet (2) and outlet (3) holes, a valve seat (12), seal 

assemblies (7, 8) and a closure / sleeve (4), connected to a drive (9), a cylindrical insert (11) 

mounted in the said body, said closure is embodied in the form of a hollow sleeve (5) mounted in 

the body with the possibility of reciprocal movement along the external surface of the cylindrical 

insert, characterized in that the sleeve consists of two coupled cylindrical parts (5, 6), where the 

external diameter of the part thereof connecting the body constituting 0.9–1.1 of the internal 

diameter of the part thereof connecting the insert. 

18160


(54) Title of the invention: “APPARATUS AND METHOD FOR RECEIVING A QUASI– 

COMPLEMENTARY TURBO CODES (QCTC) AND DECODING THE 

QCTC.” 

(51) International Classification 7 :H03M 13/27 


(31) Document No.: 2001–7916 

(32) Date : 16/02/2001 



(66) Filed U/s 5(2) : NIL 








SAMSUNG ELECTRONICS CO., LTD., 


416, Maetan–dong, Paldal–gu, Suwon–shi, 

Kyungki–do, Republic of Korea. 


KIM, Min–Goo; 

JANG, Jae–Sung; 

HA,Sang–Hyuck; 

An apparatus generates quasi–complementary turbo codes in a communication system. The 

apparatus includes a turbo encoder, an interleaver for interleaving symbols output from the turbo 

encoder according to a give rule, and a code generator for generating the quasi–complementary 

turbo codes by puncturing and repeating the interleaved symbols from the interleaver. Further, an 

apparatus decodes quasi–complementary turbo codes in the communication system. The decoding 

apparatus includes a code decoder for generating code symbols according to a code rate 

transmitted through depuncturing sub–code of quasi–complementary turbo codes transmitted from 

a transmitter and soft combining the sub–codes, a deinterleaver for deinterleaving the symbols 

output form the code decoder, and a turbo decoder for decoding an output of the deinterleaver. 

18161


(54) Title of the invention: “A Process For Preparing Herbal Composition For The Treatment of 

Animal Bites Especially Snake Bite And Early Stages of Hydrophobia” 

(51) International Classification 7 : A61K 39/205 





(66) Filed U/s 5(2) : NIL 







PRASAD Vaidya Bank, 


Gautam Buddha Jan Kalyan Seva Sansthan, 

Bhainsahan, Sadar Tola, Post–Hetimpur, 

NH28, Distt. Khusinagar, U.P.–274206, 


GUPTA KRISHNA CHANDRA 

MALL TRIVENI 


This invention deals with the process of preparing synergistic herbal composition for the 

treatment of animal bites treating animal bites and an early stages of hydrophobia. The ingredients 

used in the composition are Crotolaria prostrata, solanum suratiense, Cassia occidentalis and 

Menispermaceae in ratio of 4:1:1:1. The parts of these plant are pounded together to bruise the cell 

wall untill the said parts are pounded into a pulp. The pulp is thereafter soaked in water for around 

28 hours in a cool place. Thereafter it is decanted and the sediment is stored for use in treating 

animal bite especially snake bite and early stages of hydrophobia 

18162


(54) Title of the invention: “AN APPARATUS FOR MANUFACTURING TOOTHBRUSHES AND A 

PROCESS OF FORMING THE SAME.” 

(51) International Classification 7 : H03M 13/27 


(31) Document No.: 09/067,728; 09/293,019 

(32) Date : 28/04/1998; 16/04/1999 

(33) Name of convention country : U.S.A 

(66) Filed U/s 5(2) : NIL 







GILLETTE CANADA COMPANY, 


4 Robert Speck Parkway, Missisauga, Ontario, 

L4Z 4C5, Canada 


DECLAN CONNOLLY 

MICHAEL FRYAUF 

MARK MCCONNELL 

GERALD STEVEN SZCZECH 


An apparatus for manufacturing toothbrushes is provided that includes a molding unit (100) for 

substantially simultaneously molding toothbrush bodies (12), an element that removes toothbrush 

bodies (12) from the molding unit (100), a tufter (200) for securing tufts of bristles to toothbrush 

bodies (12) to form toothbrushes, and a transport for automatically moving toothbrush bodies (12) 

from the removal element to the tufter (200). A process for forming toothbrushes is also disclosed. 

10 

100 

300 

A 

A 

410 

16 

14 

400 

200 

310 

420 

480 

500 

18163


(54) Title of the invention: “FUEL CELL ASSEMBLY” 



(31) Document No.: 09/854,362 

(32) Date : 15/05/2001 


(66) Filed U/s 5(2) : NIL 








HYDROGENICS CORPORATION, 


5985 McLaughlin Road, Mississauga, Ontario 

L5R 1BB, Canada. 


FRANK, DAVID GEORGE 

CARGNELLI, JOSEPH 

FRISCH, LAWRENCE EUGENE 

BRADFORD, WILLIAM GORDON 

MAXSON, MYRON TIMOTHY 

SWANTON, BRIAN JEFFERY 

TRAVIS, HOWARD STIMSON 

A fuel cell assembly comprising a plurality of individual fuel cells, each fuel cell 

composed of a plurality of separate elements located with respect to one another to provide 

connection apertures there between, said connection apertures together forming a connection duct 

constituting at least one groove network extending through said assembly, said at least one groove 

network being provided with at least one filling port for providing within said network a “formed 

in place” seal after said separate elements have been assembled, said seal providing a barrier 

between at least two of said separate elements to define a chamber for a fluid for operation of the 

fuel cell, the connection ducts of individual fuel cells being interconnected to one another and to 

said at least one filling port thereby providing said groove network extending through the plurality 

of said fuel cell s. 

18164

(21) Application No. 1685/DEL/1998 (22) Date of filing of Application: 18/06/1998 

(54) Title of the invention: “An Improved Process For The Production of Esters From Carboxylic 

Acids Using Montomorrilonite Catalysts.” 






(66) Filed U/s 5(2) : NIL 


NA 






COUNCIL OF SCIENTIFIC INDUSTRIAL 

RESEARCH 




BOYAPATI MANORANJAN CHOUDARY 

VELDURTHY BHASKAR 

MANNEPALLI LAKSHMI KANTAM 

KOTTAPALLI KOTESWARA RAO 

KONDAPURAM VIJAY RAGHAVAN 


An improved process for the production of esters from carboxylic acid using modified 

clay catalyst by reacting carboxylic acid with alcohol in a molar ratio of about 1:5 in presence of 

solvent medium and metal exchanged montmorrilonite as catalyst in a ratio of about 40:1 at a 

temperature ranging from 80 0 C to 130 0 C for a period in the range of 2.5 to 15 hours and recovering 

esters by separating catalyst through filteration and removing the solvent by known methods. 

18165


(54) Title of the invention: “NONWOVEN–FABRIC–TYPE OIL FILTER INTEGRAL TO VALVE 

BODY .” 

(51) International Classification 7 : D04H 1/42 


(31) Document No.: 10–2003–0062122 

(32) Date : 05.09.2003 

(33) Name of convention country : Korea. 

(66) Filed U/s 5(2) : NIL 







HYUNDAI MOTOR COMPANY, 


Corporation Organized and Existing Under 

The Law of Republic of Korea, of 231, 

Yongiae–Dong Seocho–Ku, Seoul, Korea. 


KIM KI HYUP 

The present invention relates to a nonwoven–fabric–type oil filter integral to a valve body, 

which includes: a first cover member mounted to an open side of the valve body, the first cover 

member having at least one first oil hole for allowing oil flow therethrough; a second cover 

member conjoined with the first cover member, the second cover member having at least one 

second oil hole; and nonwoven fabric oil filter disposed between the first and second cover 

members, for filtering oil flowing from the valve body into a hollow portion therebetween. 

18166


(54) Title of the invention: “AN APPARATUS AND A METHOD THEREOF FOR 

DEMODULATING A CODE WORD .” 



(31) Document No.: 2002–81028 

(32) Date : 18.12.2002 

(33) Name of convention country : KOREA. 

(66) Filed U/s 5(2) : NIL 


NA 






SAMSUNG ELECTRONICS CO. LTD., 


416, Maetan–dong, Yeongtong–gu, Suwon–si, 

Gyeonggi–do Republic of Korea. 


SUNG–HYU HAN 

KI–HYUN KIM 

IN–SIK PARK 

YOON–WOO LEE 

A apparatus and method therof for demodulating a code word. The demodulation 

apparatus includes a code table including a plurality of the code words, wherein similar ones of the 

code words are arranged to be grouped together; and a soft demodulator to calculate probabilities 

of individual bits that constitute the code words, and to generate soft demodulation value of the 

data word. 

18167


(54) Title of the invention: “A Process For Purification of Sodium Chloride Containing Sodium 

Sulphate Impurity.” 






(66) Filed U/s 5(2) : NIL 


NA 






COUNCIL OF SCIENTIFIC INDUSTRIAL 

RESEARCH 




KANAIYALAL DAMODARDAS PADIA 

SATISH HARIRAY MEHTA 

ROHIT HARIKRISHNA TRIVEDI 

KAUSHIK JETHALAL LANGALIA 

MAHESH RAMNIKLAL GANDHI 

PROF. PARAMASIVAM NATARAJAN 


A process for purification of sodium chloride containing sodium impurity which has 

definite composition. The invention consists of a composition of Didwana salts found in the 

Didwana region of Rajasthan State containing less percentage of impurities which are within the 

permissible limit for industrial grade salt. The principle of the process is based on the phase 

equilibrium of NaCl–Na2So4–H2O. The salt obtained is the upgraded salt. It provides Glauber`s 

salt and is a cyclic process with cost effectiveness. The resultant salt is named as salt efficient 

brine (SDB). Moreover induced crystallization in the invention makes the process energy efficient 

which with high industrial applicability. 

18168


(54) Title of the invention: “A PROCESS FOR MAKING CERAMICTILE FROM BLAST FURNACE 

SLAG AND CLAYEY.” 


C04B 5/00, C94B 18/14 





(66) Filed U/s 5(2) : NIL 


NA 






COUNCIL OF SCIENTIFIC INDUSTRIAL & 

RESEARCH 




SACHCHIDANANDA CHAKRABARTI, 

SYAMAL GHOSH, 

MIHIR DAS, 

SANDAR GHATAK, 


A process for making ceramic tile from blast furnace slag and clayey materials. 

The process of the present invention can be used to produce ceramic tiles form iron blast 

furnace slag and clayed materials for use as floor tiles, wall tile and kitchen table top. Blast furnace 

slag contains silica, alumina and calcium oxides as principal constituents which range in 25–40%, 

5–35% and 30–50% by weight respectively. Magnesium oxide content may vary from 1–25% by 

weight. The composition depends on the source and process of iron making. In corporation of clay 

in the original batch composition results in overall increase in silica and reduction of alumina and 

lime. 

18169


(54) Title of the invention: “A PROCESS FOR PREPARATION OF SINTERING ADDITIVES IN 

POWDER FORM USEFUL FOR SINTERING OF SILICON CARBIDE.” 


C04B 35/583; C08K 3/34 





(66) Filed U/s 5(2) : NIL 


NA 







RESEARCH 




SANKAR GHATAK 

AMIYASANKAR SANYAL 

KAJAL KUMAR DHARGUPTA 

SANTANU MANDAL 


The invention relates to a process for preparation of sintering additives in powder form 

useful for sintering of silicon carbide. The process steps comprises; mixing aluminum oxide and 

aluminum nitride in attritor mill using alumina balls in the molar proportion of 5 to 95, separating 

the milled powder from alumina balls by sieving through 100 mesh B. S., preparing a slurry by 

known methods using organic solvents as herein described, drying the said slurry to obtain a 

powder, firing the said powder containing aluminum oxide and aluminium nitride at a temperature 

in the range of 1750–1850 0 C under nitrogen atmosphere for a period in the range of 1–5 hours, 

grinding the product by known methods in presence of organic solvents as defined above, drying 

the said slurry to obtain sintering additives in powder form. 

18170


(54) Title of the invention: “AN IMPROVED PROCESS FOR MAKING AND MAGNESIUM 

ALUMINATE SPINEL USEFUL AS REFRACTORY AND 

ENGINEERING CERAMICS.” 


C04B 35/19 





(66) Filed U/s 5(2) : NIL 


NA 








RESEARCH 


Rafi Marg New Delhi–110001. 


SANKAR GHATAK 

ARUP KUMAR SAMANTA 

SANTANU MANDAL 

GAUTAM BANERJEE 

A process for making magnesium Acuminate spinal useful as refractories and 

engineering ceramics in the wide range of magnesia content which comprises preparing aluminum 

oxide suspension in a solution of magnesium salt with dispersants such as herein described, adding 

to the said suspension a soluble hydroxide such as herein described, maintaining the pH in the 

range of 9.4 to 12.4 to obtain a gel–like mass, allowing the gel like mass to age for a period in the 

range of 8 to 48 hours, filtering and washing the aged gel–like mass, drying the gel–like mass at a 

,temperature in the range of 110–200 0 C, grinding and palletizing the dried material, firing the 

palletized material at a temperature in the range of 1200–1400 0 C, grinding the pellets by known 

methods. 

18171


(54) Title of the invention: “A METHOD FOR PREPARING A STEEL PLATE 

HAVING A MICRO LAMINATE 

MICROSTRUCTURE”. 

(51) International Classification 7 : C21D 8/00 


(31) Document No.: 60/068,252 

(32) Date: 19/12/1997 










EXXONMOBIL UPSTREAM RESEARCH 

COMPANY, USA. 


100 West 10 th Street, City of Wilmington 

Country of New Castle, United States of 

America 


JAYOUNGJ KOO 

NARASIMHA-RAO V. BANGARU 

GLEN A. VAUGHN 

An ultra-high strength, weldable, low alloy steel with excellent cryogentic temperature toughness 

in the base plate and in the heat affected zone (HAZ) when welded, having a tensile strength 

greater than 830 Mpa (120 ksi) and a micro-laminate microstructure comprising austenite film 

layers and fine-grained martensite/lower bainite laths, is prepared by heating a steel slab 

comprising iron and specified weight percentages of some or all of the additives carbon, 

manganese, nickel, nitrogen, copper, chromium, molybdenum, silicon, niobium, vanadium, 

titanium, aluminum, and boron; reducing the slab to form plate in one or more passes in a 

temperature range in which austenite recrystallizes; finish rolling the plate in one or more passes in 

a temperature range below the austenite recrystallization temperature and above the Ar3 

transformation temperature; quenching the finish rolled plate to a suitable Quench Stop 

Temperature (QST); stopping the quenching; and either, for a period of time, holding the plate 

substantially at the QST or slow-cooling the plate before air cooling, or simply air cooling the plate 

to ambient temperature. 

18172


(54) Title of the invention: “PROCESS FOR THE CONVERSION OF AROMATIC 

HYDROCRBONS.” 

(51) International Classification 7 : B01J27/00, 

C07C 6/12, C0764/18, C07C 15/02 


(31) Document No.: 97106716.3,97106717.1, 

97106718.X,97106719.8,97106450.4 

(32) Date: 13/11/1997, 13/11/1997, 

13/11/1997,13/11/1997,06/06/1997 

(33) Name of convention country: CHINA 









CHINA PETRO-CHEMICAL CORPORATION 


6A, Huixindong st. Chaoyang District, Beijing, 

China, Shanghai Research Institute of 

Petrochemical Engineering, Sinopec, No. 1599 

Pudong Bei Road, Pudong New Area, 

Shanghai, China. 


CHENG, WENCAI 

KONG, DEJIN 

LI, HUAYING 

ZHU ZHIRONG 

The present invention relates to a process for the conversion of aromatic hydrocarbons using the 

catalyst composition comprising by weight 20 to 90 parts of a crystalline aluminosilicate zeolite 

with a SiO2/A12O3 molar ratio of 10 to 100, 0.05 to 10 parts of metal bismuth or oxides thereof, M 

being selected from the group consisting or molybdenum, copper, zirconium, stronitium, rhenium, 

iron, cobalt, nickel, and silver, and 10 to 60 parts of alumina as an adhesive to effect 

disproportionation and transalkylation of aromatic hydrocarbon reactants comprising substantially 

toluene and C9 aromatic hydrocarbons and/or C10 aromatic hydrocarbons as well as 

hydrodealkylation and transalkylation of heavy aromatic hydrocarbons containing C9 aromatic 

hydrocarbons and/or aromatic hydrocarbons of more than nine carbons atoms under conversion 

conditions. 

18173


(54) Title of the invention: “A PROCESS FOR IMPARTING COLOUR TO A 

MINERAL SUBSTRATE”. 

(51) International Classification 7 : C04 B 41/85, 

B32B 15/04, B05 D3/02 



(32) Date: NA 










SAMIR GUPTA, MANUJ GOYAL 


Pinkcity Gem Technologies, 76, Dhuleshwar 

Gardens, Jaipur- 302001. 


SAMIR GUPTA 

MANUJ GOYAL 

The present invention provides a process for imparting colours to colourless gemstone minerals 

and enhancing properties of gemstone-minerals by coating a film of a particular material or 

multiple films of different materials on the gemstone minerals and then subjecting said coated 

minerals substrate to heat treatment to obtain the desired colour substrate. The present invention 

also relatels to mineral gemstone prepared by this process. 

18174


(54) Title of the invention: “A DEVICE FOR MAKING MOCHA COFFEE". 



(31) Document No.: 100 34 720.7 

(32) Date: 17/07/2000 










CHRISTOPH LANG 


KLINGE 10, 73087 BAD BOLL,GERMANY. 


CHRISTOPH LANG 

A device for preparing mocha coffee is disclosed. The device comprises cooking vessel, an 

electrical heating body electrically insulated supported relative to the cooking vessel, however, 

thermally coupled to the cooking vessel, and a temperature sensor. A motor driven stirred rod (3) 

protrudes into the cooking vessel (2). A blade (4) of the stirrer rod (3) is effective for the stirring 

of the mocha coffee and is disposed immediately above the heating body(5). 

18175


(54) Title of the invention: “AN IMPROVED TRANSVERSE FAN & HEAT 

EXCHANGER ASSEMBLY”. 

(51) International Classification 7 : F04029, 

F04D 17/04 


(31) Document No.: 08/880,763 











CARRIER CORPORATION 


Carrier Parkway, P.O Box 4800, Syracuse, New 

York 13221, USA 


PETER RALPH BUSHNELL 

A flow stabilizer is provided for reducing low frequency flow oscillations within and the resultant 

noise from the impeller of a transverse fan. Such oscillations and noise can arise in installations 

where the fan is located downstream of the heat exchanger in an air conditioning unit. The 

stabilizer is a vane located between the downstream face of the heat exchanger and the suction side 

of the impeller. The vane is positioned and oriented so as to reduce localized counter swirling 

flow that otherwise would cause oscillating blade stall within the impeller and associated noise. 

18176


(54) Title of the invention: “A PROCESS FOR THE BIOTRANSFORMATION OF 

CYANOHYDROCARBONS TO CORRESPOONDING 

AMIDES” 

(51) International Classification 7 : C 12P013/02 



(32) Date: NA 















BINOD KUMAR GOGOI 

RITU ARAMABAM 

TANKESHESWAR NATH 

AJIT KUMAR HAZARIKA 

JAGDISH NARAYAN NIGAM 

NARENDRA NATH DUTTA 

The present invention relates to a process for the biotransformation of cyanohydrocarbons to 

corresponding amides. It relates to a process for the biotransformation of cyanohydrocaaarbos to 

corresponding amides using whole cell of a novel Rhodococcus sp. Strain RL4 having nitrile 

hydratase enzyme. The present invention particularly relates to conversion of aliphatic and 

aromatic cyanohyddrocarbons such as acrylonitrile, propionitrile, isobutyronitrile, benzyl cyanide, 

3-cyanopyridine and the like to the corresponding amides, and more particularly relates to an 

enzymatic process for the hydration of acrylonitrile to acrylamide scatalyzed by nitrile hyratase 

present in the resting cells of Rhodococcus sp. RL4. The main usage of the invention is to 

provide a process for the preparaton of Rhodococcus sp. RL4 cells having nitirile hydratase 

enzyme which can be used under mild reaction conditions e.g. atmospheric pressure, low 

temperature, near neutral pH to hydrate acrylonitrile to acrylamide without any by-product 

formation. 

18177


(54) Title of the invention: “A PROCESS FOR PREPARAING A CLEANSING 

PROCESSING AGENT”. 

(51) International Classification 7 : B01J 20/26, 

C02F 1/28, B00B 3/00 


(31) Document No.: P10-046020 

(32) Date: 26/02/1998 










SONY CORPORATION 


7-35, Kitashinagawa 6-chome, Shinagawa-ku, 

Tokyo, Japan. 


YASUHITO INAGAKI 

YASUTOSHI KAWATE 

KIMIKO ISHIKAWA 

HIROYUKI NAGASAWA 

A process for preparing a cleansing processing agent, characterized in that the process comprises 

the following steps: (a) preparing a polymer having 5 to 80% acrylonitrile and a resin comprising 

20 to 95% of at least one of styrene and conjugate diene (butadiene or isoprene) as constituent unit 

by processing with an acid and/or alkali as herein described, under temperature conditions in the 

range of 0 to 200 0 C, for a reaction time as herein described to produce a reaction product (b) 

washing the said reaction product to obtain a reaction product to obtain a reaction mass (c) 

gelation of the reaction mass and subsequent drying (d) mixing the product obtained in step (c) 

with materials as herein described. 

18178


(54) Title of the invention: “A FILTER CO-PROCESSOR”. 

(51) International Classification 7 : H03H 7/30 


(31) Document No.: 08/725,871 

(32) Date: 04/10/1996 










MOTOROLA, INC 


1303 East Algonquin Road, Schaumburg, 

Illinois, 60196, USA. 


THOMAS KUNDMANN 

MACK MANSOURI 

MOSHE TARRAB 

ERAN PISEK 

A filter co-processor comprising: 

a first memory (103) for storing data information; 

a second memory (106) for storing coefficients; and 

a controller (109) for controlling a multiplier/accumulator to perform multiply/accumulate 

functions during a correlation process between the stored data information representing a 

complex data sequence and the stored coefficients representing a mid-amble sequence, where the 

mid-amble sequence comprises alternating pure real/pure imaginary complex values and the output 

of the correlation is decimated, the controller coordinating retrieval of the stored data information 

and the stored coefficients. 

18179


(54) Title of the invention: “LASER APPARATUS”. 

(51) International Classification 7 : GO6K1/12 


(31) Document No.60/025,915 

(32) Date: 11/09/1996 

(33) Name of convention : USA 









THE DOMINO CORPORATION 

Address of the Applicant: 229 South State 

Street, Dover, Delaware 19901, United States 

of America. 


`VERNON SUTTER 

RICHARD BLACKBURN 

A laser apparatus has a number of individual laser devices (1) mounted at angles to one 1another. 

The output ends (2) of the laser devices are disposed closely adjacent to one another and a number 

of laser beam redirectors (5) are disposed to intercept the laser beams (3) emitted from the laser 

output ends (2) so as to extend the length of the laser beam paths and to decrease the angle 

between said laser beams (3). 

18180


(54) Title of the invention: “METHOD FOR PRODUCING CELICALLY WOUND 

LUMINOUS ELEMENTS”. 

(51) International Classification 7 : H01K 3/02, 

H01K 9/02 


(31) Document No.: 196 53 572.7 

(32) Date: 20/12/1996 










PATENT-TREUHAND-GESELLSCHAFT 

FUR ELEKTRISCHE GLUEHLAMPEN 

MBH 


Hellaabrunner Str. 1. 81543 Munchen, 

Germany. 


JUERGEN EDER 

HANS LIERMANN 

PETER SCHMIDT 

REINHARD SPRENGER 

The method is distinguished in that a thermal treatment of the incandescent wire at temperatures 

of over 1200 0 C takes place already before the winding of the incandescent wire, so that, after 

separation, the coil springs open and can easily be detached from the core wire. 

18181


(54) Title of the invention: “A DIFFUSER FOR A CENTRIFUGAL COMPRESSOR.” 

(51) International Classification 7 : F 04D 29/46 


(31) Document No.: 658,801 











CARRIER CORPORATION. 


Carrier Parkway, PO Box 4800, Syracuse, New 

York 13221, U.S.A. 


JOOST JOHANNES BRASZ 

JOHN WALTZ SALVAGE 

A variable pipe diffuser is disclosed for use in a centrifugal compressor. The variable pipe diffuser 

includes an outer ring and an inner ring which is rotatable circumferentially within the outer ring 

between a first, open position and a second, closed position. In an open position, complementary 

air channel sections of the inner and outer rings are aligned with one another to allow a maximum 

flow of refrigerant through the diffuser. In a closed position, the flow channels of the ring sections 

are misaligned and the flow of refrigerant through the diffuser is restricted. By adjusting the 

diffuser rings toward a closed position, surge conditions can be avoided even in the case where a 

high compressor pressure ratio is required. 

18182


(54) Title of the invention: “MICA TAPE AND INSULATED COIL USING THE SAME.” 

(51) International Classification 7 : B 32B 5/10, 

9/00, 15/02, 17/02 



(32) Date: NA 










KABUSHIKI KAISHA TOSHIBA AND 

NIPPON RIKA KOGYOSHO CO. LTD. 


72 Horikawa-cho, Saiwai-ku, Kawasaki-shi, 

Japan and 20-6, Ohi 1-chome, Shinagawa-ku, 

Tokyo, Japan. 


NORIYUKI IWATA 

HISAYASU MITSUI 

HIROSHI HATANO 

HIDEAKI NAKATSU 

TAKUO YOSHIDA 

A mica tape formed by a paper-making process from a mixture of a mica paper and at least one 

selected from the group consisting of a short fiber made of a nitrogen-free organic material and a 

short fiber made of an inorganic material, and an insulated coil by winding the mica tape around a 

conductive coil and impregnating the mica tape with a solventless thermosetting resin. The short 

fiber has an average diameter of 0.1 to 20 µm and an average length of 0.5 to 10 mm. 

18183


(54) Title of the invention: “A DEVICE FOR PERFORMING INTRAVASCULAR OR 

INTRACARDIAC PROCEDURES.” 


VIACOR INCORPORATED. 

(51) International Classification 7 : A 61F 2/24, 

A 61M 5/00 


(31) Document No.: 60/117,599; 60/152,135; 

60/161,934 

(32) Date: 27/01/1999; 25/08/1999 & 

28/010/1999 










66-H Concord Street, Wilmington, MA 01887, 



GREGORY H. LAMBRECHT 

JOHN LIDDICOAT 

ROBERT KEVIN MOORE 

The present invention discloses devices and methods for performing intravascular procedures 

without cardiac bypass. The devices include various embodiments of temporary filter devices (10), 

temporary valves (26), and prosthetic valves (90). The temporary filter devices (10) have one or 

more cannulae (2) which provide access for surgical tools for effecting repair of the cardiac valves. 

A cannula (2) may have filters (3) of various configurations encircling the distal region of the 

cannula, which prevents embolism material from entering the cornonary arteries, and aorta. The 

temporary valve devices (26) may also have one or more cannulae (2) which guide insertion of the 

valve into the aorta. The valve devices (26) expand in the arorta to occupy the entire flow path of 

the vessel. In one embodiment, the temporary valve (26) is a disc of flexible, porous material that 

acts to filter blood passing therethrough. A set of valve leaflets extend peripherally from the disc. 

These leaflets can alternately collapse to prevent blood flow through the valve, and extend to 

permit flow. 

18184


(54) Title of the invention: “A MACHINE FOR CONTINUOUSLY REPROFILING A 

CORRUGATED MATERIAL.” 


ONDULINE. 

(51) International Classification 7 : B 29C 53/28, 

44/8 


(31) Document No.: 9613763 

(32) Date: 12/11/1996 










38, rue Saint Ferdinand, 75017, Paris, France. 


MICHEL BUCHY 

A machine for continuously reprofiling a corrugated material characterized in that it comprises: 

- support bars (7) for the corrugated material, driven in translation and perpendicular to their 

direction of displacement, 

- reprofiling bars (2) fixed to an endless chain (11) rotatably driven and movable in 

translation with respect to said chain (11), 

- counter-forming bars (6) fixed to another endless chain (16), also rotatably driven, and 

movable in translation with respect to said chain (16), 

the profile of the counter-forming bars being complementary to that of the reprofiling bars, 

the reprofiling bars (2) and counter-forming bars (6) being positioned on either side of the 

plane of the support bars (7) in such a way that parts of said bars are opposite one another 

and the translation movements of the reprofiling and counter-forming bars opposite one 

another are made approximately, perpendicular to the plane of the support bars. 

18185


(54) Title of the invention: “A METHOD OF MANUFACTURING THE DATA CARRIER.” 

(51) International Classification 7 : G 06K 

19/067, 


(31) Document No.: 19641219.6 

(32) Date: 27/09/1996 










ATOTECH DEUTSCHLAND GMBH. 


Erasmusstrasse 20-24, 10553 Berlin, Germany. 


FRANZ KOHNLE 

There is described a data carrier for storing binary data, for example a telephone card, and a 

method of manufacturing this data carrier. 

Known storage media with an irreversible storage mechanism contain superficially applied 

patterns, comprising metal layers, the first layer abutting on the carrier material consisting of a 

nickel/phosphorous alloy and the second of a tin/lead alloy layer. 

In contrast, the data carriers according to the invention contain as a second metal layer a tin/zinc 

alloy layer. This is less toxic than the known tin/lead alloy layers and is outstandingly suitable for 

the indicated purpose on the storage media. 

The manufacturing method for the storage media comprises substantially the following process 

steps: 

a) formation of a resist layer with channels on the carrier, in which the surface areas of the 

carrier corresponding to the metal structures to be formed later, are not covered: 

b) electroless deposition of a layer of nickel or of a nickel alloy in the channels; 

c) electrolytic deposition of a tin/zinc alloy layer on the first layer, 

the exposed surfaces of the carrier being activated by means of an appropriate catalyst for 

subsequent electroless metal deposition before process step a) or between process step a) and 

b). 

18186


(54) Title of the invention: “PACKAGING WRAPPER AND A PROCESS FOR 

PACKAGING AN ARTICLE.” 


TRANSPAC, N.V. 

(51) International Classification 7 : B 65D 

75/10, 65/14, B 65B 7/12 & B 32B 23/02 



(32) Date: NA 










Avenue Herrmann-Debroux, 46, B-1160, 

Bruxelles, Belgium. 


EDDY DAELMANS 

RAYMOND VANOPPRE 

Packaging wrapper consisting of a film (10, 40) intended to be closed by two twists (18) on either 

side of an article to be packaged (12) and comprising, on the internal side relative to the article to 

be packaged (12), a sealing coating placed along two transverse strips (20a, 20b) and (46a, 46b) on 

either side of the article to be packaged (12) and extending parallel to an axis passing through the 

two twists (18). The packaging process consists in sealing the package at the transverse strips. 

18187


(54) Title of the invention: “CONTACT LENS CONTAINER AND METHOD FOR USING 

THE SAME.” 


JOHNSON & JOHNSON VISION PRODUCTS, 

INC. 

(51) International Classification 7 : A 61F 9/00, 

B 65D 85/38 


(31) Document No.: 08/727,994 

(32) Date: 10/10/1996 










4500 Salisbury Road, Suite 300, Jacksonville, 

Florida 33216, United States of America. 


ROBERT CHARLES BAUMAN 

A contact lens container comprising an integrally molded one-piece synthetic resin receptacle 

providing a well having a peripheral wall with a bottom portion, and a flange extending about the 

periphery of the upper end of well. The bottom portion has a generally concave inner surface for 

seating a contact lens thereon and is being relatively rigid. The peripheral wall of the well has an 

annular, resiliently deflectable inversion portion above the bottom portion, and it is invertible to 

position the bottom portion of the well above the plane of the flange. Pressing upwardly against the 

bottom portion of the well inverts the inversion portion of the well and dispose the bottom portion 

with the lens thereon above the plane of the flange. The receptacle is moved against the eye of the 

user to place the lens against the cornea and thereby cause the lens to seat thereon. 

18188


(54) Title of the invention: “A METHOD FOR DEMODULATING A CODE DIVISION 

MULTIPLE ACCESS (CDMA) SIGNAL IN A 

(51) International Classification 7 : H 04B 7/216 


(31) Document No.: 08/778,430 

(32) Date: 02/01/1997 









COMMUNICATION SYSTEM.” 


MOTOROLA INC. 



IIIinois, 60196, United States of America. 


GREGORY PETER SPOCK 

In a code division multiple access (CDMA) signal demodulator in a communication system (50), 

samples of a CDMA signal are stored in a sample buffer (52). A plurality of the samples that 

represent a plurality of chips of a symbol are then recalled from the sample buffer (52). Thereafter, 

the plurality of samples are demodulated in parallel (56) using a selected user code (68) to produce 

at least a portion of a user’s symbol in the code division multiple access signal. Signals from 

multiple users (22, 24) having multiple fingers are demodulated by sharing the resources of a 

parallel demodulator (56). Signal searching may use the same parallel demodulator (56). Fingers 

for multiple users may be dynamically allocated and relocated according to the needs of each 

user’s signal and the total demodulation resources available. 

18189


(54) Title of the invention: “A RADIOTELEPHONE CONFIGURED TO RECEIVE DS- 

CDMA SIGNALS IN A COMMUNICATION SYSTEM.” 


MOTOROLA, INC. 

(51) International Classification 7 : H 04Q 7/32 


(31) Document No.: 08/741,183 

(32) Date: 29/10/1996 











Illinois, 60196, United States of America. 


RICHARD JOSEPH VILMUR 

A radiotelephone configured to receive DS-CDMA signals in a communication system having a 

plurality of base stations, each base station being identified by a unique starting phase of a known 

pseudorandom noise (PN) sequence, the radiotelephone comprising: 

a rake receiver (112) having a plurality of receiver fingers (122, 124, 126) 

a receiver searcher (114) for detecting pilot signals from the plurality of base stations, wherein the 

pilot signals are quadrature modulated, each of the pilot signals having in-phase (I) symbols and 

quadrature-phase (Q) symbols, wherein the I symbols are spread using an I PN sequence and the Q 

symbols are spread using a QPN sequence, 

the receiver searcher having a matched filter (128) for comparing a detected PN sequence and a 

predetermined PN sequence and producing a response, wherein the matched filter includes 

an I filter for comparing a detected I PN sequence and a stored I PN sequence, and 

an Q filer for comparing a detected Q PN sequence and a stored Q PN sequence; and 

a controller (116) coupled to the receiver searcher and the rake receiver, the controller having a 

memory for storing the responses as a stored response, the controller controlling the plurality of 

receiver fingers in response to the stored response. 

18190


(54) Title of the invention: “METHOD FOR MAKING SECURE ENCLOSURE FOR 

AUTOMATED BANKING MACHINE.” 


INTERBOLD. 

(51) International Classification 7 : E 06B 3/34 


(31) Document No.: 60/031,887 

(32) Date: 27/11/1996 













DONALD WAYNE HARRY 

GERALD THOMAS SEDLOCK 

THOMAS ANDREW VANKIRK 

JOSEPH MICHAEL KALINOWSKI 

A secure enclosure (10) for an automated banking machine includes a chest portion (12) and a 

moveable door (14). The door is supported on hinge assemblies (20, 22) which enable mounting 

and accurately positioning the door despite misalignment of the hinges. One hinge assembly 

includes a pin (156) which has a ball (186) thereon. The pin is accepted into a larger bore (164) of 

the other hinge assembly despite axial misalignment of the hinge and bore. The bore has an 

adjusting screw (188) movably positioned therein which engages the ball when the hinge 

assemblies are connected. Movement of the adjusting screw enables adjusting the relative positions 

of the hinge assemblies. In making the secure enclosure one hinge assembly is attached to the chest 

while the other hinge assembly is attached to the door. The hinge assemblies are connected to 

movably mount the door on the enclosure. The hinges are adjusted so that dead bolt projections 

(150) on the door engage aperture (62) when the door is in a closing position. 

18191


(54) Title of the invention: “A DATA TRANSMISSION NETWORK FOR THE 

TRANSMISSION OF A NUMBER OF TELEPHONE 

(51) International Classification 7 : H 04J 3/07 


(31) Document No.: 1333/95 










CHANNELS AND A METHOD THERE FOR.” 


TELLABS DENMARK A/S. 


Lautrupbjerg 7-11, DK-2750 Ballerup, 

Denmark. 


ANDERS BOJE NIELSEN 

A data transmission network for the transmission of a large number of telephone channels between 

nodes in the network, said transmission network being designed as a Synchronous Digital 

Hierarchy (SDH), where a pulse frame (e.g. STM-1) contains a large number of bytes, each of 

which may be used for transmitting a telephone channel or overhead signals for administering the 

system, and where signals from a Plesiochronous Digital Hierarchy, so that the signals from the 

Plesiochronous Digital Hierarchy when inserted do not occupy all the bytes in said pulse frame, 

characterized in that at least some of the bytes in the pulse frame which are not occupied by said 

insertion are used for transmitting user-specified data signals. 

18192


(54) Title of the invention: “INFORMATION RECORDING CARD AND METHOD OF 

USING THE SAME.” 


EMPIRE AIRPORT SERVICE CO., LTD. 

(51) International Classification 7 : G 06K 

19/18, 19/14 


(31) Document No.: 25409/1996, 54810/1996, 

92460/1996 & 155765/1996 

(32) Date: 13/02/1996, 12/03/1996, 15/04/1996 

& 17/06/1996 









An information recording card (10) comprising: 

a base card (11); 


34-6, Shiba 5-Chome, Minato-ku, Tokyo-To, 

Japan. 


MINORU OKADA 

MIKIO HORIUCHI 

an information recording unit provided in the base card comprising a magnetic stripe (12); and 

a plurality of optical waveguides (15) provided in the base card; 

characterized in that said magnetic stripe (12) has a plurality of unit magnetic segments (12a) each 

having a predetermined storage capacity; and 

in that the plurality of optical waveguides (15) are disposed so as to correspond to the unit 

magnetic segments (12a), respectively. 

18193


(54) Title of the invention: “METHOD FOR PRODUCTION OF A COOLING PLATE.” 

(51) International Classification 7 : B 22D 62/13 


(31) Document No.: 90 003 & 90 146 

(32) Date: 08/01/1997 & 30/09/1997 


Luxembourg 









PAUL WURTH S.A. & OUTOKUMPU 

PORICOPPER OY. 


32, rue d’Alsace, L-1122 Luxembourg, and SF- 

28330 Port, Finland. 


MAR SOLVI 

ROGER THILL 

YRJO LEPPANEN 

PERTTI MAKINEN 

A method for production of a cooling plate (50, 80) with integrated coolant ducts for iron and steel 

making furnaces from an ingot of copper, characterized by the steps of: 

continuously casting said ingot of copper by means of a continuous casting mould (10) as a 

perform of said cooling plate (50, 80), wherein rod-shaped inserts (28) in a casting duct (20) of 

said continuous casting mould (10) produce cast-in ducts (52, 84) running in the continuous 

casting direction through said ingot of copper; and 

manufacturing said cooling plate (50, 80) from said continuously cast perform, wherein said castin 

ducts (52, 84) form integrated coolant ducts in said cooling plate (50, 80). 

18194


(54) Title of the invention: “A CUTTING ELEMENT FOR A SAFETY RAZOR.” 


(30) Priority Data: B 26B 21/00, 21/56 

(31) Document No.: 9700037.6 

(32) Date: 03/01/1997 

(33) Name of convention country: UK 









THE GILLETTE COMPANY. 


Prudential Tower Building, Boston, 

Massachusettes 02199, United States of America. 


RICHARD GARRAWAY 

A novel cutting element in or for a safety razor comprises an elongate member with a series of 

slots (5), each slot (5) tapering from an open forward end to a substantially closed trailing end, and 

each slot (5) being confined between a pair of shaped edges (6) for slicing hairs as they move 

through the slot as the cutting element is moved across the skin. One or more of the cutting 

element may be used in a safety razor blade unit, either alone or in combination with a blade 

having a conventional straight sharpened edge. 

18195

(21) Application No. 2478/DEL/1997 A (22) Date of filing of Application: 01/09/1997 

(54) Title of the invention: “A DIGITAL BROADCASTING APPARATUS.” 

(51) International Classification 7 : H 04N 7/16 


(31) Document No.: 8-230015 & 9-56687 

(32) Date: 30/08/1996 & 11/03/1997 










MATSUSHITA ELECTRIC INDUSTRIAL CO., 

LIMITED. 


1006, Oaza Kadoma, Kadoma-shi, Osaka 571- 

8501, Japan. 


TATSUYA SHIMOJI 

KAZUO OKAMURA 

JUNICHI HIRAI 

MASAHIRO OASHI 

TAKASHI KAKIUCHI 

YUKI KUSUMI 

YOSHIYUKI MIYABE 

IKUO MINAKATA 

MASAYUKI KOZUKA 

YOSHIHIRO MIMURA 

SHINJI INOUE 

TOSHIYA MORI 

NAOYA TAKAO 

A broadcasting system which includes a broadcasting apparatus and a reception apparatus and 

which achieves interactiveness using a broadcast wave.The broadcasting apparatus includes a 

content storing unit for storing the plurality of contents, each content including a set of video data 

and a set of control information that indicates another content that is a link destination for a present 

content, and a transmitting unit for multiplexing a set of video data and a plurality of sets of the 

same control information included in a same content as the set of video data, and for transmitting 

the multiplexed sets of video data and control information. The reception apparatus includes an 

extracting unit for extracting a set of video data and a set of control information in a same content 

as the set of video data, a storing unit for storing the extracted set of control information, a 

reproducing unit for reproducing the extracted set of video data and outputting an image signal, an 

operation unit for receiving a user operation that indicates a content switching, and a control unit 

for controlling the extracting unit to extract another content indicated by the set of control 

information stored in the storing unit, in accordance with the user operation. 

18196


(54) Title of the invention: “LENTICULAR LENS SHEET.” 

(51) International Classification 7 : G 02B 3/00 


(31) Document No.: 216250/1996 & 

170568/1997 

(32) Date : 16/08/1996 & 26/06/1997 

(33) Name of convention country : JAPAN. 

(66) Filed U/s 5(2) : NIL 





Total No. of Pages: 



DAI NIPPON PRINTING CO., LTD. 


1-1, Ichigaya-kaga-cho, 1-Chome, Shinjuku-ku, 

Tokyo-To, Japan. 


MASAHIRO GOTO 

A lenticular lens sheet includes a substrate layer, a lens portion having a lenticular lens 

configuration which is shaped so as to be convex on a light incident face side of the substrate layer 

and an achromatic or chromatic colored layer formed adjacent to at least a light incident face of the 

lens portion. The substrate layer is not colored. Alternatively, it is colored thinner than the colored 

layer. With the arrangement, it is possible to restrict reflection of outside light and enhance the 

contrast of picture without reducing the intensity of image light so much. Further, it is possible to 

realize fine pitching of images. 

18197


(54) Title of the invention: “AN IMPROVED PROCESS FOR PREPARATION OF MN-ZN 

FERRITES.” 

(51) International Classification 7 : B 22F 1/00 





NA 

(66) Filed U/s 5(2) : NIL 











Rafi Marg, New Delhi – 110 001, India. 


KAMALA KANTA SAHOO 

CHANDANA RATH 

SHASHI ANAND 

NARESH CHANDRA MISHRA 

RADHANATH PRASAD DAS 

An improved process for the preparation of Mn-Zn ferrites by preparing aquous solutions of ferric 

chloride, zinc chloride and manganese chloride, by known methods adjusting the pH of the iron 

chloride to 9.0 to 9.5 so as to precipitate iron as hydroxide using 5-10% aqueous ammonia, 

washing the prepared iron hydroxide mass till free of chloride, mixing the iron hydroxide slurry 

with zinc and manganese chloride solutions, adjusting again the pH of the mixed contents to 10.0 

with 5-10% ammoniua solution to obtain a slurry, autoclaving the above said slurry at 150-210 o C 

for 2 to 3 hours and recovering Mn-Zn ferrites by known methods. 

18198


(54) Title of the invention: “SYSTEM AND METHOD FOR EMBEDDING ADDITIONAL 

INFORMATION IN COMPRESSED AUDIO DATA.” 


G 06F 15/00 


(31) Document No.: 11-364627 

(32) Date : 22/12/1999 


JAPAN 

(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 


Total No. of Pages: 50 




CORPORATION. 




TACHIBANA RYUKI 

SHIMIZU SHUHICHI 

KOBAYASHI SEIJI 

A system for embedding additional information in compressed audio data comprising: 

(1) means for extracting MDCT coefficients from said compressed audio data; 

(2) means for employing said MDCT coefficients to calculate a frequency component for said 

compressed audio data; 

(3) means for embedding additional information in said frequency component obtained in a 

frequency domain; 

(4) means for transforming into MDCT coefficients said frequency component in which said 

additional information is embedded; and 

(5) means for using said MDCT coefficients, in which said additional information is 

embedded, to generate compressed audio data. 

18199

(21) Application No. IN/PCT/2002/561/DEL A (22) Date of filing of Application: 03/06/2002 

(54) Title of the invention: “A DEVICE FOR TRANSMITTING PACKET DATA IN MOBILE 

COMMUNICATIONS SYSTEM.” 

(51) International Classification 7 : H 04L 12/56 


(31) Document No.: 62153/2000 

(32) Date : 21/10/2000 


Republic of KOREA 

(66) Filed U/s 5(2) : NIL 










416, Maetan-dong, Paldal-gu, Suwon-shi, 442- 

370, Kyungki-do, Republic of Korea. 


KIM, MIN-GOO 

HA, SANG-HYUCK 

There is provided a device and method for transmitting packet data in a mobile communication system. 

A sub-code generator generates a plurality of sub-codes with the same of different code rates for the 

input of a PLP (Physical Layer Packet) information bit stream. A Controller determines a minimum 

data rate by which the number of the modulation symbols of a sub-code generated by a predetermined 

modulation method is equal to or greater than the number of transmittable modulation symbols for each 

time period. A symbol pruner prunes part of the modulation symbols of the sub-code equal to the 

number of transmittable modulation symbols for the time period, if the number of the modulation 

symbols of the sub-code is greater than the number of transmittable modulation symbols for the time 

period. 

18200



STERICALLY CONTROLLED STYRENE ACRYLONITRILE 

COPOLYMER.” 

(51) International Classification 7 : C 08F 114/18 





NA 

(66) Filed U/s 5(2) : NIL 













SOUNDAR DIVAKAR 

PALANISWAMY RAVI 

An improved process for the preparation of styrene acrylonitrile copolymer using β-cyclodextrin 

by polymerizing by conventional method styrene and acrylonitrile in presence of clathrate (with 

respect to styrene monomer) wherein the ratio of monomer to clathrate ranges from (10:1 to 20:1) 

in presence of conventional initiator and surface active agent at a temperature in the range of 80 to 

90 o C for minimum 10 hrs and recovering styrene-acrylonitrile is a copolymer by known methods. 

Styrene acrylonitrile copolymer is used in preparation of house-ware applications, automobile 

components and packaging industry. 

18201


(54) Title of the invention: “AN IMPROVED PROCESS FOR THE PRODUCTION OF 

PROPYLENE BY NON-CATALYTIC OXYCRACKING OF PROPANE 

OR PROPANE-RICH C2-C4 PARAFFINS.” 

(51) International Classification 7 : C 01B 003/24 





NA 

(66) Filed U/s 5(2) : NIL 













VASNT RAMCHANDRA CHOUDHARY 

AMARJEET MUNSHIRAM RAJPUT 

VILAS HARI RANE 

This invention relates to an improved process for the production of propylene and ethylene by noncatalytic 

oxidative cracking of propane or propane-rich C2-C4 paraffins. The invention particularly 

relates to production of propylene and ethylene by non-catalytic oxidative conversion of propane or 

propane-rich C2-C4 paraffins in a most energy efficient manner by allowing the endothermic 

hydrocarbon cracking reactions to occur simultaneously with the exothermic hydrocarbons oxidative 

conversion reactions in an empty tubular reactor. 

18202

(21) Application No. 268/DELNP/2004 A (22) Date of filing of Application: 06/02/2004 

(54) Title of the invention: “A METHOD FOR DETERMINING A JITTER BUFFER DEPTH 

TARGET.” 


H 04L 12/28, 29/06, G 07F 7/00 


(31) Document No.: 60/311,703 & 09/973,206 

(32) Date : 10/08/2001 & 09/10/2001 


U.S.A. 

(66) Filed U/s 5(2) : NIL 








MOTOROLA INC. 



Illinois 60196, U.S.A. 


JOHN M. HARRIS 

A method for determining a jitter buffer depth target comprising steps of: 

determining a radio frequency (RF) load metric associated with a plurality of actively engaged 

communication channels at a base site; 

comparing the determined RF load metric to an RF load threshold to produce a comparison; and 

determining a jitter buffer depth target based on the comparison. 

18203


(54) Title of the invention: “A BARREL ASSEMBLY.” 

(51) International Classification 7 : B 22D 17/00, 17/20, B 

29C 45/17 


(31) Document No.: 09/791,373 

(32) Date : 23/02/2001 


U.S.A. 

(66) Filed U/s 5(2) : NIL 








HUSKY INJECTION MOLDING 

SYSTEMS LTD. 


AMC/IPS Group, 500 Queen Street 

South, Bolton, Ontario L7E 5S5, 

Canada. 


MARTIN R. KESTLE 

CLIVE A. TOOMEY 

ANTHONY PAULOVIC 

A barrel assembly for use in an injection unit of an injection molding machine including a first and a 

second barrel portion wherein the first barrel coupler isolates the second barrel portion from axial 

carriage force. 

18204


(54) Title of the invention: “A DATA PROCESSING APPARATUS AND A METHOD OF 

OPERATING THE SAME.” 

(51) International Classification 7 : G 06F 9/34, G 06F 12/02 





NA 

(66) Filed U/s 5(2) : NIL 





Total No. of Pages:119 



ARM LIMITED. 


110 Fulbourn Road, Cherry 

Hinton, Cambridge CB1 9NJ, 

England. 


RICHARD YORK 

HEDLEY JAMES FRANCES 

DOMINIC SYMES 

STUART BILES 

The present invention provides a data processing apparatus comprising: a plurality of registers for 

storing data items to be processed; a processor for processing instructions to be applied to data items 

stored in said plurality of registers; and register remapping logic for converting a logical register 

reference within a preselected set of instructions to a physical register reference identifying the register 

containing the data item required for processing by the processor. 

By this approach, a remapping instruction need only by executed once in order for the remapping to be 

applied to a desired number of instructions. This is in contrast to prior art techniques, where subsequent 

to a remapping instruction being executed, the remapping is applied to all subsequent instructions, ie. a 

desired number of instructions cannot be selected. 

The invention is particularly advantageously employed in apparatus arranged to repeat in instruction 

loop, the instruction loop including said preselected set of instructions . In such cases, loop hardware 

used to manage the repeat instruction can be arranged to update the register remapping locig each time 

the instruction loop is repeated, and hence the remapping logic is only executed once prior to the repeat 

instruction being executed. 

18205


(54) Title of the invention: “METHOD AND APPARATUS FOR THE PROCESSING OF 

TUBES MADE OF PLASTIC.” 

(51) International Classification 7 : B 29C 47/92 


(31) Document No.: 9611705 

(32) Date : 26/09/1996 


FRANCE 

(66) Filed U/s 5(2) : NIL 








ALPHACAN. 


12/18 Avenue de La Jonchere Elysee 2, F- 

78170 La Celle Saint-Cloud, France. 


BERNARD PREVOTAT 

JEAN-JACQUES ACKET 

Method for the processing of tubes made of plastic, especially PVC, obtained by extrusion, according 

to which a tube is brought to a molecular orientation temperature higher than ambient temperature and 

is subjected to biaxial stretching by radial expansion and by axial elongation, in order to obtain a biorientation 

tube having improved mechanical properties. The tube (T) is cut into elements (4) of 

specific length when it has just been extruded and when its temperature is higher than the molecular 

orientation temperature, each element constituting a blank (5); each blank (5) is placed in an enclosure 

(E) in order to be cooled there by a fluid (F) at a temperature near the molecular orientation 

temperature, the dwell time of the blank in the enclosure being longer than the time for producing the 

blank by extrusion; and the blank (5) is subsequently extracted from the enclosure (E) in order to 

undergo the processing which ensures bi-orientation by radial expansion and axial elongation. 




MOLYBDEMUM DISILICIDE (MOSI2)-REACTION BONDED SILICON 

CARBIDE (RBSC)COMPOSITE USEFUL AS A STRUCTURAL CERAMIC 

MATERIAL.” 

(51) International Classification 7 : C 04B 35/56, 35/58 





NA 

(66) Filed U/s 5(2) : NIL 













PROBAL KUMAR DAS 

OM PRAKASH CHAKRABARTI 

A process for the preparation MoSi2-RBSC composite containing alloy species mixing it with the 

PVA solution and pressing isostatically. The invention relates to a process for the preparation of 

molybdenum disilicide (MoSi2)-reaction bonded silicon carbide (RBSC) in which melt of alloy 

molybdenum and silicon are bonded by the bonded silicon carbide forming the duplex non-oxide 

ceramic useful as a structural ceramic material. 

18207


(54) Title of the invention: “METHOD FOR FULFILLING REQUESTS FOR INFORMATION 

DATA FROM A NETWORK.” 

(51) International Classification 7 : G 06F 17/30 


(31) Document No.: 00480128.8 

(32) Date : 20/12/2000 


EP 

(66) Filed U/s 5(2) : NIL 









CORPORATION. 




AUFFRAY VINCENT 

BRICARD ARNAUD 

LECOMTE FABIEN 

LESCARMONTIER ARNOLD 

VALLADE JEAN-MARIE 

Disclosed herein are a method and a system of fulfilling requests for information data from a 

network client in a client-server environment. The information data requested is accessible from a 

network server and is displayable through a form-based format hypertext document whereby the 

information data are provided by the filling of dedicated form fields in the hypertext document. 

The method comprises the following steps. Receiving (13) at the network client a hypertext 

document and a program component; displaying (31) the hypertext document, the hypertext 

document having initially no information data filling its form fields; obtaining (41) a request for 

information from a user of the network client, through a user interface presented to the user as a 

result of the displaying of the hypertext document, and calling (43) the program component for 

obtaining the requested information data; upon determination (51) that the requested information 

data is already or not stored in a buffer memory allocated to the program component in the 

network client, obtaining (57) the requested data by retrieving them from the buffer memory, or 

downloading (53, 55, 57) them from the network server; filling (59) the appropriate form fields in 

the hypertext document with the obtained information data, and displaying the hypertext document 

with the requested information data contained therein. 

18208


(54) Title of the invention: “AN ELECTROCHEMICAL CELL USEFUL IN THE REDUCTION OF 

NITRO COMPOUNDS.” 

(51) International Classification 7 : H 01M 6/02 





NA 

(66) Filed U/s 5(2) : NIL 





Total No. of Pages: 06 






Rafi Marg, New Delhi – 110 001, 

India. 


PAYYALLUR NARAYANAN 

ANANTHARAMAN 

DEVANATH VASUDEVAN 

CINGARAN RAVICHANDRAN 

The invention relates to an electrochemical cell useful in the reduction of nitro compounds. The 

cell comprises: in combination a novel cathode consisting of Ti/ceramic TiO2 and the said cathode 

sheet being coated with a solution consisting of titanyl acetyl acetonate or titanyl butanoate, nitric 

acid or hydrochloric acid, water and isopropanol as herein described, lead as anode, a porous 

diaphragm, the nitro or dinitro compound in sulphuric acid as the catholyte and sulphuric acid as 

the anolyte. 

18209


(54) Title of the invention: “A GRANULAR DETERGENT COMPOSITION.” 

51) International Classification 7 : C 11D 9/22 


(31) Document No.: 60/061,880 

(32) Date : 10/10/1997 


U.S.A. 

(66) Filed U/s 5(2) : NIL 








THE PROCTER & GAMBLE 

COMPANY. 


One Procter & Gamble Plaza, Cincinnati 

State of Ohio, United States of America. 


KVIETOK, FRANK ANDREZ 

KATSUDA, RINKO 

HELTOVICS, GABOR 

WILLMAN, KENNETH WILLIAM 

A detergent composition, having a selected surfactant system for improved performance, especially 

under high water hardness and low temperature wash water conditions is disclosed. The detergent 

composition includes a mid-chain branched primary alkyl sulfate surfactant in combination with a 

linear alkylbenzene sulfonate surfactant, and linear alkyl sulfate surfactant at optimally selected 

relative proportions. Additionally, the detergent composition contains up to about 5% of an alkyl 

ethoxylated sulfate surfactant and up to about 5% of a nonionic surfactant while unexpectedly having 

improved performance with such relatively low levels of a nonionic surfactant. 

18210


(54) Title of the invention: “A METHOD AND APPARATUS FOR CARRYING OUT CRYOGENIC 

AIR SEPARATION .” 

(51) International Classification 7 : F 25J 3/04 





(66) Filed U/s 5(2) : NIL 








PRAXAIR TECHNOLOGY, INC. 


39 Old Ridgebury Road, Danbury, State 

of Connecticut 06810-5113, United 

States of America. 


DANTE PATRICK BONAQUIST 

NANCY JEAN LYNCH 

A method for carrying out cryogenic air separation comprising: 

(A) passing a first portion (67) of the feed air (60) for a cryogenic air separation plant (10, 11) through 

a primary heat exchanger (1) and thereafter passing the first feed air portion (70) into the cryogenic 

air separation plant (10); 

(B) compressing a second portion (66) of the feed air (60) for the cryogenic air separation plant (10, 11) 

to a high pressure and passing at least some stream of feed air portion (64) of the high pressure 

second feed air portion (68) as input to a high ratio turboexpander (32) without passing through any 

portion of the primary heat exchanger, wherein the pressure of the gas input to said high ratio 

turboexpander is at least 15 times the pressure of the gas output from said high ratio turboexpander; 

(C) turboexpanding the high ratio turboexpander input (64) through the high ratio turboexpander (32) 

and passing the resulting turboexpanded output (82, 83) into the cryogenic air separation plant (11); 

(D) separating the feed air (70, 72, 83) within the cryogenic air separation plant (10, 11) by cryogenic 

rectification to produce at least one of product oxygen (76, 84) and product nitrogen (91, 93); and 

(E) recovering at least one of product oxygen (84) and product nitrogen (93) from the cryogenic air 

separation plant (10, 11); 

characterized in that 

in step (C) the resulting turboexpanded output (82, 83) is passed into the cryogenic air separation plant 

(11) without passing through any portion of the primary heat exchanger (1). 

18211


(54) Title of the invention: “A PROCESS FOR THE PREPARATION OF SUPPORTED SOLID 

CATALYST USEFUL FOR FRIEDEL-CRAFTS REACTIONS.” 


C 07C 





NA 

(66) Filed U/s 5(2) : NIL 


No. : NA 



:NIL 






RESEARCH. 




VASANT RAMCHANDRA CHOUDHARY 

SUMAN KUMAR JANA 

B-PHANI KIRAN 

The present invention relates to a process for the preparation of supported solid catalyst useful for 

Friedel Crafts reaction. The present invention provides the preparation of supported solid catalyst 

comprising of mixed metal oxides or halides deposited on porous catalyst carriers or supports useful 

for heterogeneously or solid catalyzed Friedel-Crafts reaction. 

18212


(54) Title of the invention: “SYSTEM FOR ENCODING A PLURALITY OF BIT SEQUENCES.” 



(31) Document No.: 09/477,289 

(32) Date : 04/01/2000 


U.S.A. 

(66) Filed U/s 5(2) : NIL 









MACHINES CORPORATION. 


Armonk, New York 10504, United States 

of America. 


WAGNER, MARCUS 

The present invention provides an improved system and method for encoding a plurality of bit 

sequences. The present invention includes reading a bit sequence; determining a minimum number of 

bits for a repeat factor for the bit sequence, where the minimum number of bits is variable; and 

encoding the bit sequence using the repeat factor. The method provides an improved run-length 

encoding algorithm by using a strategy where the number of bits used to represent the repeat factor 

(RF) varies for each individual sequence of equal-valued bits. Rather than conventionally representing 

the RF by any predetermined and fixed number of bits, the RF of the present invention is represented 

by the minimum number of bits to binary-encode that repeat factor as an unsigned integer. The key 

advantage of providing the variable width RF run-length encoding algorithm is that the RF for each 

individual bit sequence is represented using only the minimum number of bits necessary, regardless of 

any previous or following RF. Consequently, a compression ratio can be obtained, which is higher than 

that obtained with the conventional algorithms, over a wide range of sequence length distributions in 

the data to compress. Additionally, the variable width RF is data driven in that the data to compress is 

what controls how many bits are used to represent the RF. Therefore, it is unnecessary to know the bit 

value sequence distribution in advance, which makes the method in accordance with the present 

invention well suited for real-time application. 

18213


(54) Title of the invention: “A METHOD FOR FORMING A DIFFUSION REGION IN A SILICON 

SUBSTRATE.” 

(51) International Classification 7 : H 01L 21/20 


(31) Document No.: 09/400,676 

(32) Date : 21/09/1999 


U.S.A. 

(66) Filed U/s 5(2) : NIL 













COOLBAUGH DOUGLAS D. 

HARAME DAVID L. 

A method of forming a diffusion region in a silicon substrate having low-resistance, acceptable defect 

density, reliability and process control comprising the steps of: (a) subjecting a silicon substrate to a 

first ion implantation step, said first ion implantation step being conducted under conditions such that a 

region of amorphized Si is formed in said silicon substrate; (b) subjecting said silicon substrate 

containing said region of amorphized Si to a second ion implantation step, said second ion implantation 

step being carried out by implanting a dopant ion into said silicon substrate under conditions such that 

the peak of implant of said dopant ion is within the region of amorphized Si; and (c) annealing said 

silicon substrate under conditions such that said region of amorphized Si is re-crystallized thereby 

forming a diffusion region in said silicon substrate is provided. 

18214


(54) Title of the invention: “ENCODING APPARATUS IN A MOBILE COMMUNICATION 

SYSTEM.” 



(31) Document No.: 2001/14418, 2001/15294 & 

2001/15787 

(32) Date : 20/03/2001, 23/03/2001 & 26/03/2001 



(66) Filed U/s 5(2) : NIL 










416, Maetan-dong, Paldal-gu, Suwon-shi, 

442-370 Kyungki-do, Republic of Korea. 


KIM, JAE-YOEL 

CHOI, HO-KYU 

JANG, JAE-SUNG 

KIM,YOUN-SUN 

An encoding method in a mobile communication system, for receiving 4 input information bits, 

encoding the 4 input information bits with different, walsh codes of length 16, and outputting a coded 

symbol stream having 24 coded symbols using a coded symbol stream having 16 coded symbols 

obtained by XORing the encoded input information bits by an XOR operator. The encoding method 

comprises repeating the coded symbol stream having 16 coded symbols once, and thus outputting a 

coded symbol stream having 32 coded symbols; and puncturing 0 th , 1 st , 2 nd , 3 rd , 4 th , 5 th , 6 th and 16 th 

symbols from the 32 coded symbols, and thus outputting the coded symbol stream having 24 coded 

symbols. 

18215


(54) Title of the invention: “AN ABSORBENT ARTICLE FOR IMPROVING SKIN CONDITION OF 

A WEARER IN THE AREA COVERED BY ABSORBENT ARTICLE.” 

(51) International Classification 7 : A 61F 13/15 


(31) Document No.:08/926,532 

(32) Date : 10/09/1997 


(66) Filed U/s 5(2) : NIL 








THE PROCTER & GAMBLE COMPANY. 


One Procter & Gamble Plaza Cincinnati State 

of Ohio United States of America. 


LAURA GRAVES SPALDING VAN 

RIJSWIJCK 

MAURICIO ROLANDO ODIO 

MICHELLE DENISE ROSEMAN 

GRETCHEN LOUISE ELDER 

SUSAN BALDWIN 

KEVIN EUGENE GRANDISON 

This invention relates to an absorbent article which comprises a liquid imperious backsheet, a liquid 

pervious topsheet and an absorbent core. A skin care composition is applied on a portion of topsheet. 

The skin care composition is semi solid or solid at 20 o C. The amount of the skin care composition is 

determined such that at least 0.03 mg/in 2 (0.0047 mg/cm 2 ) is transferred to wearer skin in a 24 hours 

period, by applying to wearer an unused absorbent article having the skin care composition. 

18216


(54) Title of the invention: “MULTIPLE CHANNEL DUCT ASSEMBLY FOR CABLES.” 

(51) International Classification 7 : H 02G 3/04 


(31) Document No.:1999/26147 



KOREA 

(66) Filed U/s 5(2) : NIL 








BYUN, MOO-WON 


102-1306 Hyundai Apt., 39/7, 413-1 

Poongnap-Dong, Songpa-Gu, Seoul 138- 

040, Korea. 


BYUN, MOO-WON 

The multiple channel duct assembly for cables comprises of a plurality of plastic inner ducts 

contiguous, co-directionally extending, substantially parallel, in abutting contact with each other, each 

of the said inner ducts having cross-sectional areas sufficient to contain at least one cable; and a plastic 

outer duct encircling said inner ducts over their entire length to retain them in their contiguous 

relationship; wherein said outer duct has a corrugated tubular section including a plurality of 

contiguous ridges and troughs extending over the entire length; whereby said assembly is so flexible 

that it can be coiled around transportable reels as well as so strong that it can withstand dirt in a trench. 

The aspect of inner ducts of plastic with less friction provides sufficiently smooth inside surfaces to the 

inner ducts, through which fiber optic cables, electric wires or the likes are inserted. 

18217


(54) Title of the invention: “A METHOD OF PRODUCING BIOLOGICAL FERTILIZER BASED 

ON YEASTS.” 


C 05F 11/08, C 12N 13/00, 1/16, 1/18 




(33) Name of convention country : -NA 

(66) Filed U/s 5(2) : NIL 








ULTRA BIOTECH LIMITED. 


60 Circular Road, Douglas IM1 1SA, 

Isle of Man (GB) UK. 


ZHANG, LINGYU 

The present invention provides a method of producing biological fertilizer compositions that comprise 

yeast cells that have an enhanced ability to fix atmospheric nitrogen, decompose phosphorous minerals 

and compounds, decompose potassium minerals and compounds, decompose complex carbon 

compounds, over produce growth factors, and over produce ATP. The biological fertilizer composition 

of the invention can replace mineral fertilizers in supplying nitrogen, phosphorus, and potassium to 

crop plants. Methods of uses are disclosed. 

18218


(54) Title of the invention: “ A CAM SYSTEM TO GENERATE VALVE ACTUATION IN AN 

ENGINE” 

(51) International Classification 7 : F 01L 1/30,13/00 


(31) Document No.: PCT/US99/19839 

(32) Date : 28/08/1998 

(33) Name of convention country :U.S. 

(66) Filed U/s 5(2) : NIL 








TERRY GLYN LINEBARGER. 


C/O. JOHN R. KEVILLE, 750 BERING 

DRIVE, HOUSTON, TX 77057-2198, 

U.S. 


TERRY GLYN LINEBARGER 

A cam system (20) to generate valve actuation in an engine (10) that includes a circular cam lobe (50) 

rotated about a first axis (55) is described. The first axis is a preselected distance from the centerpoint 

(52) of the circular camlobe. The cam system also includes a cam follower (100) that surrounds the 

camlobe and that has an inner oval surface (105) with a major and minor axis. The inner oval surface is 

in moving contact with the circular cam lobe during rotation of the cam lobe. 

18219

(21) Application No. 1396/DEL /1999 A (22) Date of filing of Application: 21/10/1999 

(54) Title of the invention: “CAR GLASS MOUNTING SYSTEM.” 

(51) International Classification 7 : G 06F 19/00 


(31) Document No.: 98-61573 

(32) Date : 30/12/1998 


KOREA 

(66) Filed U/s 5(2) : NIL 








HYUNDAI MOTOR COMPANY. 


140-2, kye-dong, Jongro-ku, Seoul, Korea. 


CHOI JONG-BUM 

A car glass mounting system includes a glass-species classifying and glass feeding device. The 

glass-species classifying and glass feeding device is loaded with species-classified front and rear 

glasses each with a glass spacer to automatically select and feed the required species of front and 

rear glasses onto a glass serve line. A glass spacer separating device separates the glass spacers 

from the front and rear glasses fed through the glass serve line. A glass lifting and positioning 

device correctly controls positions of the front and rear glasses fed through the glass serve line. A 

glass lifting and turning device correctly controls positions of the front and rear glasses fed through 

the glass serve line such that the front glass is attached with a first rubber dam and a room mirror, 

and the rear glass is attached with a second rubber dam. A primer coating device coats primer onto 

the front and rear glasses fed through the glass serve line while amending the coating positions of 

the front and rear glasses such that the primer coating layer is tightly attached with a sealer coating 

layer to be subsequently coated. A glass unloading and loading device unloads the front and rear 

glasses fed through the glass serve line and loads the front and rear glasses onto a carriage. A 

sealer coating and glass mounting device coats sealer onto the primer coated positions of the front 

and rear glasses fed through the carriage and mounts the sealer-coated front and rear glasses within 

a car body. 

18220


(54) Title of the invention: “AN AQUEOUS BASED HEAVY-DUTY LIQUID DETERGENT 

COMPOSITION.” 

(51) International Classification 7 : C 11D 1/22 


(31) Document No.: 60/116516 

(32) Date : 20/01/1999 


(66) Filed U/s 5(2) : NIL 




No. :NIL 





COMPANY. 


One Procter & Gamble Plaza, Cincinnati, 

State of Ohio, United States of America. 


KOTT, KEVIN LEE 

SCHEIBEL, JEFFREY JOHN 

SEVERSON, ROLAND GEORGE 

CRIPE THOMAS ANTHONY 

BURCKETT-ST, LAURENT, JAMES 

C.T.R. 

WATSON, RANDALL ALAN 

GARCIA, RAQUEL LOPEZ 

The present invention relates to aqueous based heavy-duty liquid detergent compositions 

containing a modified alkylbenzene sulfonate surfactant (MABS), as co-surfactant (alkyl 

polyhydroxy fatty acid amide and/or alkyl amidopropyl dimethyl amine) and an aqueous liquid 

carrier. The MABS comprises a mixture of specific branched and non-branched alkylbenzene 

sulfonate compounds, which are further characterized by a 2/3-phenyl index of 160-275. 

18221


(54) Title of the invention: “GENERATOR OF AN ADAPTED SPEECH RECOGNIZER.” 

(51) International Classification 7 : G 01L 5/06 


(31) Document No.: 60/082,656, 09/066,113 

(32) Date : 22/04/1998, 23/04/1998 


(66) Filed U/s 5(2) : NIL 









MACHINES CORPORATION. 




FISCHER VOLKER 

GAO YUQING 

PICHENY MICHAEL A. 

FUNZMANN SIEGFRIED 

The invention relates to a generator and a method for generating an adapted speaker independent 

speech recognizer. 

The generator of an adapted speech recognizer is being based upon a base speech recognizer of an 

arbitrary base language. The generator also comprises an additional speech data corpus used for 

generation of said adapted speech recognizer. Said additional speech data corpus comprises a 

collection of domain specific speech data and/or dialect specific speech data. Said generator 

comprises reestimation means for reestimating language or domain specific acoustic model 

parameters of the base speech recognizer by a speaker adaption technique. Said additional speech 

data corpus is exploited by said reestimation means for generating the adapted speech recognizer. 

The invention proposes smoothing means for smoothing means for smoothing the reestimated 

acoustic model parameters. A beneficial range for the smoothing factor of a Bayesian smoothing 

is given. 

It is further suggested to iterate the adaption process. 

18222


(54) Title of the invention: “PIN GRID ARRAY EXTRACTION DEVICE.” 

(51) International Classification 7 : H 01R 4/46 



(32) Date : 


(66) Filed U/s 5(2) : NIL 








CENTRE FOR DEVELOPMENT OF 

TELEMATICS. 


9 th Floor, Akbar Bhavan, Chanakyapuri, 

New Delhi – 110 021, India. 


THAMARAYOOR RAPHEAL 

FRANCIS 

The present invention relates to a pin grid array extraction device for extracting integrated circuits 

from an electronic component device comprising: 

a main central block having means for extracting and holding the integrated circuit from the said 

electronic device; 

an additional central block attached to the said means for extracting and holding the integrated 

circuit from the said electronic device; 

attachment means for connecting the said main central block and the additional central block; and 

means for regulating the convergence and divergence of the means for extracting and holding the 

integrated circuit from the said electronic device 

wherein the main central block comprises a pair of support arms hinged to the main central block, 

each of the said support arms having a puller arm. 

18223

(21) Application No. 1066/DEL/2003 A (22) Date of filing of Application: 29/08/2003 

(54) Title of the invention: “COEXTRUSION TIE BASED ON COGRAFTED METALLOCENE 

POLYETHYLENE AND LLDPE, ON SBS AND ON PE.” 

(51) International Classification 7 : C 08L 43/00 


(31) Document No.: 02.11438 

(32) Date : 16/09/2002 

(33) Name of convention country : FRANCE 

(66) Filed U/s 5(2) : NIL 








ATOFINA. 


4-8, Cours Michelet, F-92800 Puteaux, 

France. 


PRADEL JEAN-LAURENT 

PASCAL JEROME, LE BEURON 

ROBERT PATRICE. 

The present invention relates to a coextrusion tie comprising: 

- 10 to 35 weight% of a polymer (A) itself composed of a blend of 80 to 20 weight% of a 

metallocene polyethylene (A1) with a density of between 0.865 and 0.915 and of 20 to 80 

weight% of a non-metallocene LLDPE polyethylene (A2), the blend of polymers (A1) and 

(A2) being cografted by an unsaturated carboxylic acid or its derivative, the content of 

which in the said blend is between 30 and 100 000 ppm; 

- 40 to 60 weight% of a styrene/butadiene/styrene block copolymer (B) with 50 to 90 mol% 

of styrene; 

- 20 to 35 weight% of PE (C); 

the total making 100%, the blend of (A), (B) and (C) being such that the MFI or melt flow 

index (ASTM D 1238, 190 o C, 2.16 kg) is between 0.1 and 10 g/10 min. 

The present invention also relates to a multiplayer structure comprising a layer of tie according 

to the invention and to the objects comprising such a structure. 



(54) Title of the invention: “A PROCESS FOR THE PRODUCTION OF NITROARENES WITH 

HIGH PARA-SELECTIVITY FROM MONOSUBSTITUTED 

AROMATIC HYDROCARBONS USING ALUMINOSILICATES AS 

CATALYSTS.” 


C 07C 201/08, 205/12, 205/06, 205/37 





(66) Filed U/s 5(2) : NIL 













BOYAPATI MANORANJAN 

CHOUDARY 

MUTYALA SATEESH 

MANNEPALLI LAKSHMI KANTAM 

KOTTAPALLI KOTESWARA RAO 

KOMPELLA VISHWESHWAR RAM 

PRASAD 

KONDAPURAM VIJAYA RAGHAVAN 

The present invention provides a process for the production of nitroarenes with high para 

selectivity from monosubstituted aromatic hydrocarbons using aluminosilicate as catalysts, which 

comprises nitration of monosubstiututed aromatic hydrocarbons using beta zeolite of different si/al 

ratio ranging between 5 to 1000 as catalyst with nitric acid in the molar ratio of 0.25 to 2.5 at a 

temperature ranging between 30-1600c for a period ranging between 0.25 to 3.0 h and followed by 

continuous removal of water formed from the reaction mixture with a dear-stark apparatus and 

recovery of the product mixture by concentration of the reaction mixture after separation of the 

catalyst by filtration. The process is useful for the production of many large volume chemicals 

such as nitrotoluene, nitrochlorobenzene and others as vital intermediate for dyes, drugs and 

pesticides. 

18225


(54) Title of the invention: “A METHOD FOR PRODUCING AN IMMUNO-CONTRACEPTIVE 

VACCINE.” 

(51) International Classification 7 : C 07K 14/47 



(32) Date : 


(66) Filed U/s 5(2) : NIL 




08/DEL/1997 

(64) Filed on : 02/01/1997 




NATIONAL INSTITUTE OF 

IMMUNOLOGY. 


Aruna Asaf Ali Marg, New Delhi – 110 067, 

India. 


SATISH KUMAR GUPTA 

MANJU SHARMA 

ARUNA BEHRA 

RACHNA BISHT 

RENUKA KAUL 

The present invention relates to a method for producing an immuno-contraceptive vaccine comprising 

the steps of isolating and preparing amino acid sequence comprising a peptide consisting of zona 

pellucida-1 (ZP1) shown in figure 3 mixing with the sequence with a pharmacologically acceptable 

carrier, and optionally an adjuvant such as herein described in a ratio of 4:1. 

18226

(21) Application No. 3068/DEL/1998 A (22) Date of filing of Application: 20/10/1998 

(54) Title of the invention: “AN IMPROVED PROCESSFOR THE PREPARATION OF 

DIHYDROXY ALKENES.” 

(51) International Classification 7 : C 07C 27/00, C 

07C 41/03 

(30) Priority Data : NA 




(66) Filed U/s 5(2) : NIL 













DILIP DHARAMDAS SAWAIKAR 

GURUNATH SURYAVANSHI 

ARUMUGAM SUDALAI 

An improved process for the preparation of dihydroxy alkenes using titanium silicate by mixing 

of substrate having conjugated double bonds, water solvent, oxidizing agent and heterogenous 

catalyst TS-1 (titanium silicate) in the ratio ranging about 2.0-5.0: 5-25: 0-25: 4-25: 1-5, heating 

the mixture as obtained in step (a) in an autoclave at a temperature ranging 50 o C-100 o C for period 

ranging 1 to 12 hours, followed by cooling of the reaction mixture to ambient temperature and 

separating of titanium silicate and solvent by known methods to obtain the mixture of dihydroxy 

alkene. Dihydroxy alkenes is important industrial chemicals. 

18227


(54) Title of the invention: “AN IMPROVED PROCESS FOR THE PREPARATION OF CERAMIC 

MATRIX COMPOSITES SUCH AS Al2O3 - Sicw COMPOSITE.” 

(51) International Classification 7 : C 04B 41/80 





(66) Filed U/s 5(2) : NIL 












DEBAJYOTI BANDYOPADHYAY 

LOKESH CHANDRA PATHAK 

RANJIT GHATAK GANGULY 

SWAPAN KUMAR DAS 

PATCHA RAMACHANDRA RAO 

The process of present invention provides a modified SHS technique termed as rapid heating self 

propagating high temperature synthesis (RH-SHS) for the manufacture of ceramic composites. In 

this modified technique, the reacting mixture is heated rapidly so that a sharp thermal gradient is 

established between surface and the core of the samples. A wide range of ceramic matrix 

composites such as Al2O3 – TiC, Al2O3 – WC, MoSi2 – SiC, Al2O3 – TiB2, MgO – TiC, Al2O3 – 

AIN – SiC, Al2O3 – ZrB2, TiB2 – B4C can be synthesized by this modified SHS process. In this 

present invention aluminium, silica and carbon is used as raw materials for the production of Al2O3 

– SiCw in-situ composite. 

18228


(54) Title of the invention: “A PROCESS FOR THE PREPARATION OF WATER DISPERSABLE 

BENTONITE GRAFTED ACRYLIC COPOLYMER.” 

(51) International Classification 7 : C 09K 3/10, 

D 06M 15/00 





(66) Filed U/s 5(2) : NIL 










Rafi Marg, New Delhi 110 001, india. 


YALAVARTHI 

LAKSHMINARAYANA 

THIRUMALACHARI RAMASAMI 

GANGA RADHAKRISHNAN 

KORITALA PANDURANGA RAO 

SAMAYAVARAM RAMALINGAM 

KARIKASSERY ANTONY RAPHEL 

KRISHNASWAMI PARTHASARATHI 

KRISHNA BALLABH GUPTA 

KONDAPURAM VIJAYA 

RAGHAVAN 

A process for the preparation of water dispersable bentonite grafted acrylic copolymer by heating 

an aqueous dispersion of bentonite to a temperature in the range of 55 o -95 o C, copolymerising an 

acid acrylic monomer in the Bentonite dispersion medium in presence of a free radical initiator 

over a period of 3.5 to 7.5 hours, cooling the resultant graft polymer to a temperature in the range 

of 25 o – 35 o C to obtain acrylic copolymer, adjusting the pH of the end product adding sodium 

hydroxide, ammonia hydroxide or trichanolamine to the end product in the range of 4.5 – 5.5. 

18229


(54) Title of the invention: “MODIFIED CELLULOSIC FIBERS AND FIBROUS WEBS 

CONTAINING THESE FIBERS.” 

(51) International Classification 7 : D 21C 9/00, D 21H 11/20 


(31) Document No.: 60/049,457 



U.S.A. 

(66) Filed U/s 5(2) : NIL 







NORTH CAROLINA STATE 

UNIVERSITY. 


1 Holladay Hall, Raleigh, North 

Carolina 27695-7003, United 



SEGER, GEOFFREY 

EUGENE 

MACKEY, LARRY NEIL 

TROKHAN, PAUL DENNIS 

A method for preparing modified cellulosic fibers, comprising combining one or more cellulase 

enzymes, cellulosic fibers, and one or more debonding agents, wherein the cellulosic fibers are allowed 

to react with the one or more cellulase enzymes and the one or more debonding agents for a period 

sufficient to reduce the dry zero span tensile index of the fibers by 35% to 65% compared with the dry 

zero span tensile index of the corresponding unmodified cellulosic fibers and to reduce the wet zero 

span tensile index by at least about 70% compared with the wet zero span tensile index of the 

corresponding unmodified cellulosic fibers, wherein the fibers are at least partially bleached. 

18230


(54) Title of the invention: “PROCESS FOR THE PREPARATION OF ACTIVE SOMATOTROPIN 

FROM INCLUSION BODIES.” 

(51) International Classification 7 : C 07K 14/61, 1/00, C 12P 21/02 


(31) Document No.: 1998-34910 

(32) Date : 27/08/1998 

(33) Name of convention country : KOREA 

(66) Filed U/s 5(2) : NIL 







LG CHEMICL LIMITED. 


20, Yoido-dong, Yongdungpogu, 

Seoul 150-721, Korea. 


LEE YONG-JUN 

LEE HONG-KYUN 

HAN KYUBOEM 

A process for the preparation of biologically active form of a somatotropin protein from inclusion 

bodies of a recombinant host cell containing an inactive form of said somatotropin protein, which 

is characterized by comprises the steps of: 

(a) contacting the inclusion bodies with an aqueous solution containing an alcohol at an 

alkaline pH ranging from 9 to 13 to solubilize said somatotropin protein; 

(b) decreasing the concentration of the alcohol in the aqueous solution; 

(c) bringing the aqueous solution into contact with a mild oxidizing agent to refold and form 

intramolecular disulfide bonds between cysteine residues of said somatotropin protein; and 

(d) optionally adding in either step (a) or step (c), or in both steps (a) and 

(e) a reducing agent as such as herein described, 

wherein steps (a) and (c) are performed at a temperature ranging from 0 to 50 o C. 

18231


(54) Title of the invention: “AN IMPROVED PROCESSOR HAVING INTERRUPT INTERFACE 

CONTROL LOGIC.” 

(51) International Classification 7 : G 06F 13/24 

(30) Priority Data : 10/318,248 


(32) Date : 11/12/2002 


(66) Filed U/s 5(2) : NIL 







INTEL CORPORATION. 


Of 2200 Mission College Boulevard, 

Santa Clara, California 95052, United 



STEVEN M. BENNET 

MICHEAL KOZUCH 

GILBERT NEIGER 

ERIC COTA-ROBLES 

STALINSELVARAJ JEYASINGH 

ALAIN KAGI 

RICHARD UHLIG 

An improved processor, characterized in that, it has interrupt controller interface logic to: 

recognize a pending interrupt during the operation of guest software; determine whether the 

interrupt is managed by the guest software; determine whether a virtual machine monitor is ready 

to receive control; and 

transition control to the virtual machine monitor. 

18232

(21) Application No.00836/DELNP/2003 A (22) Date of filing of Application:28/05/2003 

(54) Title of the invention: “A SYSTEM FOR PROCESSING A ORIGINATOR REQUEST OF A 

CUSTOMER.” 



(31) Document No: 00124061.3 




(61) Patent of addition to application No: NA 


(63) Divisional to Application No: NIL 








New Orchard Road Armonk, New York 

10504, U.S.A 


ALGESHEIMER MULLER JOY 

CACHIN CHRISTAIN 

CAMENISCH JAN 

KARJOTH GUNTER 

The invention provides a method and system for processing securely an originator request of a 

customer. This originator request can be sent to at least one first entity. The method for processing 

the originator request comprises the steps of a) sending from the customer the originator request to 

the or each first entity: b) connecting the or each first entity to a computation entity; c) adding by the 

or each first entity, on receipt of the originator request, information concerning the originator request 

thereby forming a first-modified request; d) sending at least part of the first-modified request to at 

least the computation entity; e) having received at least part of the first-modified request by the 

computation entity deriving a computation-entity result from the at least part of the first-modified 

request f) sending at least part of the computation-entity result to the or each first entity; g) having 

received at least part of the computation-entity result by the or each first entity deriving therefrom a 

fist-entity result and forwarding it at least in part; and h) having received at least part of the firstentity 

result by the customer deriving therefrom a customer deriving therefrom a customer result. 

18233



CUSTOMER.” 


















10504, U.S.A 




CAMENISCH JAN 



customer. This originator request can be sent to at least one first entity. The method for processing 

the originator request comprises the steps of a) sending from the customer the originator request to 

the or each first entity: b) connecting the or each first entity to a computation entity; c) adding by the 

or each first entity, on receipt of the originator request, information concerning the originator request 

thereby forming a first-modified request; d) sending at least part of the first-modified request to at 

least the computation entity; e) having received at least part of the first-modified request by the 

computation entity deriving a computation-entity result from the at least part of the first-modified 

request f) sending at least part of the computation-entity result to the or each first entity; g) having 

received at least part of the computation-entity result by the or each first entity deriving therefrom a 

fist-entity result and forwarding it at least in part; and h) having received at least part of the firstentity 

result by the customer deriving therefrom a customer deriving therefrom a customer result. 

18234



CUSTOMER.” 


















10504, U.S.A 




CAMENISCH JAN 



customer. This originator request can be sent to at least one first entity. The method for 

processing the originator request comprises the steps of a) sending from the customer the 

originator request to the or each first entity: b) connecting the or each first entity to a computation 

entity; c) adding by the or each first entity, on receipt of the originator request, information 

concerning the originator request thereby forming a first-modified request; d) sending at least part 

of the first-modified request to at least the computation entity; e) having received at least part of 

the first-modified request by the computation entity deriving a computation-entity result from the 

at least part of the first-modified request f) sending at least part of the computation-entity result to 

the or each first entity; g) having received at least part of the computation-entity result by the or 

each first entity deriving therefrom a fist-entity result and forwarding it at least in part; and h) 

having received at least part of the first-entity result by the customer deriving therefrom a customer 

deriving therefrom a customer result. 

18235


(54) Title of the invention: “A FLEXIBLE STORAGE BAG.” 

(51) International Classification 7 : B65D 33/20 


(31) Document No:08/853,003 

(32) Date: 08/05/97 











COMPANY. 


Cincinnati, Ohio 45202, U.S.A. 




TWEDDELL III, RICHARD 

GARTH SHIRRLEY FORENCE 

ONEY JR, JACK LEE. 

The present invention provides a flexible storage bag comprising at least one sheet of flexible sheet 

material assembled to form a semi-enclosed container. The bag has an opening and a closure means 

for sealing the opening to convert the semi-enclosed container to a closed container. The closure 

means comprises a strip of material forming at least a portion of the periphery of the opening having a 

first side facing inwardly toward the opening and a second side facing outwardly of the opening. The 

first side exhibits an adhesion peel force after activation by a user which is greater than an adhesion 

peel force exhibited prior to activation by a user. In a preferred embodiment, the flexible storage bag 

includes at least one auxiliary venting opening located remotely from the primary opening and having 

an auxiliary closure means for sealing the auxiliary opening. The auxiliary opening has a periphery, 

and the auxiliary closure means comprises a piece of material forming at least a portion of the 

periphery and having a first side facing inwardly toward the opening and a second side facing 

outwardly of the opening. The first side exhibits an adhesion peel force after activation by a user 

which is greater than an adhesion peel force exhibited prior to activation by a user. In another 

preferred embodiment, the flexible storage bag is self-supporting with the opening extending in a 

direction normal to the opening and a substantially planar bottom extending in a direction substantially 

parallel to the opening, such that when the bottom is placed on a horizontal surface the flexible storage 

bag is self-supporting and maintains the opening in an upwardly-extending condition. Preferably, the 

bag maintains the opening in a substantially open condition. 

18236

(21) Application No. 1502/DEL/2003 A (22) Date of filing of Application:02/12/03 

(54) Title of the invention: “PROCESS FOR THE PREPARATION OF OMEGA-BENZYL ESTERS 

OF AMINODICARBOXYLIC ACID.” 

(51) International Classification 7 : C07C 67/035; C07B 61/00 


(31) Document No: 02 16344 

(32) Date: 20/12/2002 







Total no. of Pages: 22 



ISOCHEM 


12 Quai Henri IV, 75004 Paris, 

France. 


ANNE MAARIE VITRANT 

LAURENCE FERRUCCIO 

CHARLES-HENRY VINCENT 

The invention relates to a process for the preparation of an amino diacid, characterized in that the 

amino diacid is reacted with a benzyl alcohol derivative of formula (I) 

(R 1 )n 

CH2OH 

In which the R 1 substituent or substituents, which are identical or different, represent a hydrogen 

atom, a C1 to C4 alkyl group, a C1 to C4 alkoxy group or a halogen atom and n is equal to 1, 2 to 3, 

In the presence of at least one mol per mole of the amino diacid of an alkanesulphonic acid, 

optionally in the presence of a solvent, 

The intermediate alkanesulphonates of the ω-benzyl esters of amino diacids are obtained with a 

good yield and an excellent purity by virtue of this process. 

18237

(21) Application No.IN/PCT/2002/00626/DEL A (22) Date of filing of Application: 20/6/02 

(54) Title of the invention: “DISPENSING HEAD FOR A SQUEEZE BOTTLE”. 

(51) International Classification 7 : B65D 1/32 


(31) Document No: 09/470,892 

(32) Date: 22/12/99 









A dispensing head for a squeeze bottle sprayer comprising: 


EMSAR INC., 


125 Access Road, Stratford, Connecticut 

06615, U.S.A. 


SCHULTZ ROBERT S. 

sprayer housing defining a cavity therein, with an air orifice and a liquid orifice being defined 

through said housing the housing further defining a plug seal; 

a valve contained within the cavity, the valve defining an air passageway, and an outlet orifice, the 

valve being slidable along a longitudinal axis between an open position and a closed position, said 

longitudinal axis between an open position and a closed position, said longitudinal axis being 

generally aligned with the outlet orifice; 

the plug seal configured to seal the stem portion of the liquid passageway and the stem portion 

configured to seal the liquid orifice when the valve is in the closed position; 

the liquid passageway communicating with the mixing chamber and the liquid orifice in the open 

position of the valve; 

the air passageway communicating with the mixing chamber and the air orifice in the open position of 

the valve; and 

wherein the mixing chamber is out of communication with the liquid orifice and the air orifice 

when the valve is in the closed position. 

18238


(54) Title of the invention: “A METHOD FOR PREPARING A STEEL PLATE.” 

(51) International Classification 7 : C21D 8/02; 

C22C 38/48; C22C 38/50 


(31) Document No: 9-43630 

(32) Date: 27/02/97 










SUMITOMO METAL INDUSTRIES, LTD 


5-33, Kitahama, 4-Chome, Chuo-Ku, Osaka- 

Shi, Osaka, Japan 


KAZUKI FUJIWARA 

SHUJI OKAGUCHI 

MASAHIKO HAMADA 

ICHI KOMIZO 

JAYOUNG KOO 

NARASIMHHA-RAO V. BANGARU 

MICHAEL J. LUTON 

CLIFFORD W. PETERSEN 

A method for preparing a steel plate comprising about 0.2 wt% to less than about 1.7 wt% and 

having a tensile strength of at least 900 Mpa (130 Ksi), an impact energy as measured at-40 0 C (- 

40 0 F) of greater than 120 J (90 ft-1bs), and a microstructure comprising a mixed structure of 

martensite and lower bainite, wherein (i) said mixed structure occupies at least 90 vol.% in said 

microstructure, (ii) said lower bainite occupies at least 2 vol.% in said mixed structure, and (iii) 

prior austenite grains have an aspect ratio of at least 3, said method comprising the steps of heating 

a steel slab to a temperature of 950 0 C (1742 0 F) to1250 0 C (2282 0 F); hot rolling said steel slab, 

under the condition that the accumulated reduction ratio at a temperature of not higher than 950 0 C 

(1742 0 F) is at least 25%, to form steel plate; completing the hot rolling step at a temperature of not 

lower than about the Ar3 transformation temperature or 700 0 C (1292 0 F), whichever is higher, and 

cooling said steel plate from a temperature of not lower than 700 0 C (1292 0 F) at a cooling rate of 

10 0 C/sec to 45 0 C/sec (18 0 F/sec to 81 0 F/sec as measured at substantially the center of said steel 

plate until substantially the center of said steel plate is cooled to a temperature of not higher than 

450 0 (842 0 F). Optionally tempering said steel plate at a temperature of not higher than 675 0 C 

(1247 0 F). 

18239


(54) Title of the invention: “A NOVEL CATALYTIC PROCESS FOR THE PREPARATION OF 

UNSATURATED ORGANIC HALIDES.” 

(51) International Classification 7 : C07C 17/00 


(31) Document No: NA 

(32) Date: NA 













Rafi Marg New Delhi-110001, India. 


SUJIT ROY 

DINABANDHU NASKAR 

SHANTANU CHOWDHURY 

This invention relates to novel catalytic process of preparation of unsaturated organic halides. 

Particularly, this invention relates to an improved catalytic process for the preparation of 

unsaturated halides of formula RX, where R represents alkenyl, alkynyl and aromatic groups using 

a metal salt or tetraalkylammonium salt in a halogenated salt. 

18240

PATENT GRANTED ON 13.06.2005 (DELHI) 

S.No. Patent No. Patent Application No. S.No. Patent No. Patent Application No. 

1 191490 1770/DEL/1995 14 192176 1379/DEL/1999 

2 191672 282/DEL/1995 15 192181 1116/DEL/1995 

3 191674 1151/DEL/1995 16 192183 1656/DEL/1995 

4 191693 1769/DEL/1995 17 192184 1730/DEL/1995 

5 191789 2406/DEL/1995 18 192186 1842/DEL/1995 

6 191790 2259/DEL/1995 19 192187 1890/DEL/1995 

7 191817 2692/DEL/1997 20 192188 596/DEL/2000 

8 192057 779/DEL/1901 21 192189 208/DEL/2002 

9 192063 537/DEL/1995 22 192191 625/DEL/1995 

10 192157 1011/DEL/2000 23 192197 1819/DEL/1995 

11 192171 01/DEL/1996 24 192343 540/DEL/2000 

12 192172 97/DEL/1996 25 194637 1155/DEL/2001 

13 192175 1378/DEL/1999 

18241

24/06/2005 - Controller General of Patents, Designs, and Trade Marks

Create successful ePaper yourself

Delete template?

Save as template?