TFT-Display Datenblatt - Hy-Line

More documents

Recommendations

Info

Ver. 1.0 Product Specification Table 3. ELECTRICAL CHARACTERISTICS (Continue) Inverter : Power Supply Input Voltage Power Supply Input Voltage Ripple Power Supply Input Current Power Consumption Life Time LC370WXN Notes : 1. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 120 minutes at 25± 2°C. The specified current and power consumption are under the typical supply Input voltage 24Vand VBR (VBR-A : 1.65V & VBR-B :3.3V), it is total power consumption. The ripple voltage of the power supply input voltage is under 0.5 Vp-p. LPL recommend Input Voltage is 24.0V ± 5%. 2. Electrical characteristics are determined within 30 minutes at 25± 2°C. The specified currents are under the typical supply Input voltage 24V. 3. Brightness Control. This VBR-B Voltage control brightness. VBR-B Voltage After Aging Before Aging Power Supply Input Current (In-Rush) Input Voltage for Control System Signals Lamp: Parameter Symbol Brightness Adjust On/Off Brightness Adjust Function VBL IBL_A IBL_B Irush PBL VBR-A VBR-B 50,000 VBR-B Voltage Function 0V Minimum Duty (20%) 3.3V Maximum Duty (100%) . 4. The brightness of the lamp after lighted for 5minutes is defined as 100%. TS is the time required for the brightness of the center of the lamp to be not less than 95% at typical current. The screen of LCD module may be partially dark by the time the brightness of lamp is stable after turn on. 5. Specified Values are for a single lamp which is aligned horizontally. The life time is determined as the time which luminance of the lamp is 50% compared to that of initial value at the typical lamp current (VBR-A : 1.65V & VBR-B :3.3V), on condition of continuous operating at 25 ± 2°C 6. The duration of rush current is about 10ms. Min 22.8 - - - - - - - 0.0 0 Values Typ 24.0 - 5.0 5.5 5.5 6.0 - 120 1.65 - Max 25.2 0.5 5.5 6.0 6.0 6.5 8 132 3.3 3.3 Unit Vdc Vp-p A A A A A W Vdc On V on 2.5 - 5.0 Vdc Off V off -0.3 0.0 0.8 Vdc HY-LINE Computer Components / www.hy-line.de/computer V Hrs Notes 1 1 VBR-A = 1.65V … 1 VBR-A = 3.3V … 1 VBR-A = 1.65V … 2 V BR-A = 3.3V … 2 VBL = 22.8V VBR-B = 3.3V VBR-A = 1.65V VBR-A = 1.65V … 1 3 4 7 / 34
3-2. Interface Connections Ver. 1.0 Product Specification Table 4. MODULE CONNECTOR(CN1) PIN CONFIGURATION Pin No. Symbol Description LC370WXN This LCD employs two kinds of interface connection, a 30-pin connector is used for the module electronics, 14 Connectors are used for the integral backlight system. 3-2-1. LCD Module - LCD Connector(CN1) : FI-X30SSL-HF (Manufactured by JAE) or Equivalent - Mating Connector : FI-X30C2L (Manufactured by JAE) or Equivalent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 VLCD Power Supply +12.0V VLCD VLCD VLCD GND GND GND GND Select DCR Enable GND RA- RA+ GND RB- RB+ GND RC- RC+ GND RCLK- RCLK+ GND RD- RD+ GND VBR_OUT VBR_EXT Reserved GND Power Supply +12.0V Power Supply +12.0V Power Supply +12.0V Ground Ground Ground Ground Select LVDS Data format Dynamic CR Enable ( ‘L’ = Disable , ‘H’ = Enable ) Ground LVDS Receiver Signal(-) LVDS Receiver Signal(+) Ground LVDS Receiver Signal(-) LVDS Receiver Signal(+) Ground LVDS Receiver Signal(-) LVDS Receiver Signal(+) Ground LVDS Receiver Clock Signal(-) LVDS Receiver Clock Signal(+) Ground LVDS Receiver Signal(-) LVDS Receiver Signal(+) Ground VBR output form LCD module External VBR input from System to LCD module Low or NC : Normal Operating High : Interlace Free Mode Ground Note: 1. If the pin no. 9 is Ground, Interface format is “LG”, and if the pin no. 9 is Vcc(3.3V), Interface format is “DISM”. See page 27 and 28. 2. When this pin is no connection or Ground, DCR is Disabled. 3. The pin no. 30 is necessary for LCD test. When LVDS signals are abnormal operation more than 3-Vsync times and power 12V is supplied, ‘Open’ or ‘Vcc’ : LCD operate itself some test patterns.(AGP – Auto Generation Pattern) ‘Ground’ : LCD operate itself a black pattern. (NSB – No Signal Black) LPL recommend ‘Ground’ for NSB. 4. All GND (ground) pins should be connected together, which should be also connected to the LCD module’s metal frame. 5. All VLCD (power input) pins should be connected together. 6. Input Levels of LVDS signals are based on the IEA 664 Standard. HY-LINE Computer Components / www.hy-line.de/computer Note 1 2 3 8 / 34
Page 1 and 2: Kurzdaten TFT-Display Datenblatt Mo
Page 3 and 4: Number 1 2 3 4 5 6 7 8 9 3-1 3-2 3-
Page 5 and 6: 1. General Description Ver. 1.0 Pro
Page 7: 3. Electrical Specifications 3-1. E
Page 11 and 12: 3-3. Signal Timing Specifications T
Page 13 and 14: 3-5. Color Data Reference Ver. 1.0
Page 15 and 16: 3-6-2. Sequence for Inverter Power
Page 17 and 18: Table 12. GRAY SCALE SPECIFICATION
Page 19 and 20: Dimension of viewing angle range φ
Page 21 and 22: Ver. 1.0 Product Specification HY-L
Page 23 and 24: 6. Reliability Table 14. ENVIRONMEN
Page 25 and 26: 8. Packing 8-1. Designation of Lot
Page 27 and 28: Product Specification LC370WXN 9-3.
Page 29 and 30: Appendix 1-2. Host System 24 Bit Ve
Page 31 and 32: # APPENDIX 3 Appendix 2-2 Ver. 1.0
Page 33 and 34: # APPENDIX 2 Appendix 4 ■ LC370WX
Page 35: # APPENDIX 4 Appendix 6 Ver. 1.0 Pr

TFT-Display Datenblatt - Hy-Line

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?