Piaggio-Typhoon-50-EN _Service Manual
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Characteristics <strong>Typhoon</strong> <strong>50</strong><br />
Tightening Torques<br />
Name<br />
Upper steering ring nut (safety locks)<br />
Lower steering ring nut (safety locks)<br />
Handlebar fixing pin (safety locks)<br />
Name<br />
Swinging arm-engine pin (safety locks)<br />
Swinging arm-frame pin (safety locks)<br />
Shock absorber - frame nut (safety locks)<br />
Shock absorber-engine pin (safety locks)<br />
Rear wheel axis (safety locks)<br />
Bolt holding stand to the engine<br />
Name<br />
Front wheel axle nut (safety locks)<br />
Wheel axle clamp screw<br />
Lower leg screw<br />
Hydraulic cartridge stem nut<br />
Name<br />
Viti fissaggio coperchio pompa freno<br />
Brake pump support fixing screw<br />
Brake fluid pump - hose fitting<br />
Brake fluid tube - calliper fitting<br />
Calliper tightening screw<br />
Disc tightening screw (safety locks - lock with LOCTITE<br />
THREADLOCK MEDIUM TYPE 243)<br />
Oil bleed screw<br />
Calliper coupling screw<br />
STEERING ASSEMBLY<br />
FRAME ASSEMBLY<br />
FRONT SUSP<strong>EN</strong>SION<br />
FRONT BRAKE<br />
Torque in Nm<br />
35 to 40 Nm<br />
8 to 10 Nm<br />
45 to <strong>50</strong> Nm<br />
Torque in Nm<br />
33 to 41 Nm<br />
64 to 72 Nm<br />
20 to 25 Nm<br />
33 to 41 Nm<br />
104 to 126 Nm<br />
18 to 19 Nm<br />
Torque in Nm<br />
45 to <strong>50</strong> Nm<br />
6 ÷ 7 Nm<br />
15 to 20 Nm<br />
15 to 18 Nm<br />
Torque in Nm<br />
1,5 ÷ 2 Nm<br />
7 to 10 Nm<br />
13 to 18 Nm<br />
20 to 25 Nm<br />
20 to 25 Nm<br />
6 ÷ 7 Nm<br />
7 to 10 Nm<br />
20 to 25 Nm<br />
<strong>EN</strong>GINE ASSEMBLY<br />
Name<br />
Torque in Nm<br />
Clutch bell nut<br />
40 to 44 Nm<br />
Clutch lock ring nut 55 ÷ 60<br />
nut locking driving pulley on the crankshaft<br />
40 to 44 Nm<br />
Start-up lever screw 12 ÷ 13<br />
Flywheel nut<br />
40 to 44 Nm<br />
Flywheel fan screws 3 to 4<br />
Half-crank case joint bolts 12 ÷ 13<br />
Bolts holding exhaust pipe to the crankcase 22 ÷ 24<br />
Screws holding the filter box to the crank case 4 ÷ 5<br />
Head nuts 10 ÷ 11<br />
Starter screws 12 ÷ 13<br />
Ignition spark plug 25 ÷ 30<br />
Hub oil drainage cap 3 ÷ 5<br />
Oil hub level dipstick<br />
<strong>Manual</strong><br />
Rear hub cap screws 12 ÷ 13<br />
Transmission cover screws 12 ÷ 13<br />
Inlet manifold screws 8 ÷ 9<br />
Flywheel hood fixing screws 1 ÷ 2<br />
Cylinder hood fixing screws 3.5 ÷ 5<br />
Stator clamping screws 3 ÷ 4<br />
Pick-Up clamping screw 4 ÷ 5<br />
Mixer clamping screws 3 ÷ 4<br />
Screw fixing brake lever to the journal on the engine 12 ÷ 13<br />
CHAR - 10
Change language