HX Stomp Manual - English

Recommendations

Info

4. If desired, press PAGE and turn Knob 1 (Min Value) and Knob2 (Max Value) to set the range you wish to control.TIP: To reverse controller behavior, swap the min and max values.5. Press to return to the Home screen.SHORTCUT: To assign a parameter to the Snapshots controller, it's eveneasier—just push and turn the parameter's knob. The value appears inwhite text, indicating it's now assigned to a controller.SHORTCUT: Hold ACTION and press a parameter knob to quicklyremove any controller assignment (including the Snapshots controller).The value's text changes from white back to its original color, indicating nocontroller is assigned to it.Clearing a Block's Controller Assignment(s)1. From the Controller Assign screen, select the block whosecontroller assignments you want to clear and press ACTION.2. Press Knob 1 (Clear Controller).Tips for Creative Controller Assignment• By default, a parameter's Min and Max values will be pretty extreme. It pays toplay pretty conservative here, as subtle parameter adjustments go a long way.• To smoothly blend between the tone on parallel paths A and B, select a Split> A/B block and assign the Route To parameter to an expression pedal. Bydefault, a heel-down position means the signal passes fully through Path A.Moving the pedal toward the toe-down position will gradually crossfade intoPath B. Alternatively, assign a footswitch to control the Route To parameter, forinstantly switching back and forth.• If you're looking for an ultra-clean boost, instead of adding a Volume/Pan >Gain block, try assigning a footswitch to increase the Level parameter of aMixer or Output block.• If you have a favorite delay or reverb pedal, use an FX Loop block to insert itinto your tone. Assign EXP 1 or 2 to control the block's Mix parameter, whichwill smoothly blend the pedal into your tone.• For extreme psychedelic dub delay squeals, assign a footswitch to both increasea Delay's feedback and decrease its time.• Assign a footswitch to toggle between two Delay > Time parameter values,such as 1/4 and 1/8 dotted.• Assign IR Select to a footswitch. Set the two IRs as min and max values. Nowyou can instantly toggle between them.Clearing All Controller Assignments1. From the Controller Assign screen, press ACTION.2. Press Knob 2 (Clear All Controller) to clear all blocks' controllerassignments.The following dialog appears:Clear all controllers?CancelOK3. Press Knob 3 (OK).IMPORTANT! Clearing All Controller Assignments also removes the Wah andVolume assignments from EXP 1 and EXP 2. Use this function with caution!38
Global EQThe Global EQ built into HX Stomp has three fully parametric bands plus variable lowand high cut filters, and is used for compensating for the wide disparity in acousticenvironments on tour or when traveling from studio to studio. Global EQ is applied toall presets.NOTE: Global EQ is never heard from the Send or USB outputs.Resetting Global EQResetting the Global EQ returns its settings to factory default (flat).1. From the Global EQ screen, press ACTION.2. Press Knob 1 (Reset EQ).The following dialog appears:Reset Global EQ?1. Press PAGE and PAGE together to open the Menu.2. Press Knob 3 (Global EQ).The Global EQ screen appears:GLOBAL EQ OFFGLOBAL EQ ONGlobal EQGlobal EQ3. Press Knob 3 (OK).CancelOKLow110 Hz0.7 0.0 dBLow110 Hz0.7 0.0 dBFreqQGainFreqQGain3. Press the Upper Knob to turn Global EQ on and off.4. Turn the Upper Knob to select the desired EQ band—Low Cut,Low, Mid, High, or High Cut.5. Turn Knobs 1-3 to adjust the selected EQ band.39
Page 1 and 2: ®2.65 OWNER’S MANUAL40-00-0408 R
Page 3 and 4: Welcome to HX Stomp"50 pages for a
Page 5 and 6: 1. Main Display This color LCD is y
Page 7 and 8: Quick StartHooking It All UpThere a
Page 9 and 10: HX Stomp as DSP ExpansionLet's face
Page 11 and 12: Preset List1. If not already there,
Page 13 and 14: 4. Using the Lower Knob, PAGE, and
Page 15 and 16: Setting Path B's OutputThere may be
Page 17 and 18: Block Order and Stereo ImagingThe s
Page 19 and 20: EffectsHX Stomp has all the effects
Page 21 and 22: Modulation ModelsModel Subcategorie
Page 23 and 24: Volume/Pan ModelsModel Subcategorie
Page 25 and 26: Amp ModelsModel Subcategory Based O
Page 27 and 28: Mic ModelsModelBased On*57 Dynamic
Page 29 and 30: `LooperA single mono or stereo Loop
Page 31 and 32: U.S. Registered TrademarksAll produ
Page 33 and 34: SHORTCUT: Hold ACTION and press a p
Page 35 and 36: Bypass AssignAside from pressing th
Page 37: Controller AssignHX Stomp provides
Page 41 and 42: Global Settings > Ins/OutsPage Knob
Page 43 and 44: Global Settings > EXP PedalsPage Kn
Page 45 and 46: DI Recording and Re-ampingA common
Page 47 and 48: ASIOBuffer SizeYour goal is to achi
Page 49 and 50: Synchronizing Tempo via MIDICertain
Page 51 and 52: Additional ResourcesLooking for mor

HX Stomp Manual - English

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?