How to use the auto/truck key blank

F
G
1998+ chrysLer, dodge
1999+ chrysLer, Jeep
Originate New Master Key
1. This requires the vehicle to be connected to special dealer diagnostic equipment.
Add Duplicate Key - Must have two programmed
Sentry Keys
1. Insert one of the two valid keys into the ignition lock and turn to the ON (RUN) position.
2. After the key has been in the ON position for at least five seconds, but no more than 15
seconds turn the lock back to OFF.
3. Remove the key and insert the second valid key and turn to the ON position within 15
seconds. (The second key must not be the same as the first key.)
2001+ gM exporT vehicLes equipped wiTh The pkiii+
sysTeM. exporT vehicLes are easiLy idenTiFied By a 2 or 3 digiT in
The FirsT posiTion oF The vin nuMBer.
Originate New Master Key
Master Keys must be used.
1. Make proper cuts onto a GM Master key.
2. Insert the new working key into the ignition cylinder and turn it to the ON position. The
THEFT light will light up and stay on for about 10 minutes.
3. When the light goes out, repeat the same procedure as in step #2, two more times.
4. When the THEFT light goes out, the new key has been programmed.
To program the second key.
1. Within 20 seconds of completing the last step for the first key, insert a second Master key
and turn to the ON position. When the light goes out, the new key is programmed.
2. Repeat the previous step for programming up to 12 additional keys.
2001+ Ford Focus, Ford escape
H 2001+ Mazda TriBuTe onLy
Originate New Master Key
1. This requires that the vehicle be connected to special diagnostic equipment (TKO/SDD).
There are two ten minute delays involved while this device erases all existing key programming
and sets up the vehicle computer to accept new key codes. Two new keys should
be ready because the system requires a minimum of two keys in the program. After the
first two keys are programmed, additional keys can be entered individually by following the
instructions for adding duplicate keys.
119 PROGRAMMING PROCEDURES
4. A theft alarm light should illuminate after ten seconds and a single chime sound will indicate
entry into the Customer Programming Mode.
5. Turn the key to the OFF position within 60 seconds and remove the valid key.
6. Insert a new key and turn to the ON position.
7. After approximately ten seconds, a single chime will sound and the theft alarm light will
stop. Wait five seconds and turn to the OFF position.
8. The above steps must be repeated for additional keys.
Add Duplicate Key - Must have two programmed Sentry Keys
1. Insert the first working key into the ignition cylinder.
2. Turn the ignition cylinder to the ON position.
3. When the SECURITY light goes out, remove the key.
4. Insert the second working key and turn the ignition cylinder ON.
5. When the SECURITY light goes out, remove the key.
6. Insert the new duplicate key and turn the ignition cylinder ON.
7. When the SECURITY light goes out, key has been programmed.
Note: For Pontiac Grand Prix 2004-2007, it may be necessary to disconnect the battery for 10
minutes, and then continue with the 3 x 10.45 On Board Procedure
Add Duplicate Key (Requires two working keys)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within five seconds, insert a second key and turn it to ON
(RUN) then back OFF.
4. Insert the new key before ten seconds have elapsed and turn it to ON (RUN). Leave it on
for one second and turn back to OFF.
5. The security light will light up for three seconds to indicate that the new key has been successfully
programmed.
6. Once the key has been successfully programmed, do not remove the key from the ignition
cylinder. The key must be left in the cylinder for approximately 10 minutes before the programming
procedure is complete. Should someone attempt to start the vehicle or remove
the key from the ignition cylinder prior to the 10 minutes elapsing, the keys will not function
correctly and the programming procedure will have to be carried out again.