How to use the auto/truck key blank

2010-2011 Ford TransiT connecT
L Add Duplicate Key (Requires two working keys)
1. Insert and existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) for approximately 3 seconds and then back to OFF.
3. Remove the existing key, and within 10 seconds insert a second key, turning it ON (RUN)
for approximately 3 seconds, and then back to OFF.
4. Remove the second key, and within 10 seconds, insert the new, un-programmed key into
the ignition cylinder.
5. Turn the new key ON (RUN) for approximately 3 seconds and then back to OFF.
6. Repeat steps 1-5 for each additional key. A total of 8 keys can be programmed.
gM high securiTy key (norTh aMerica, excepT canada)
M Add Duplicate Key
1. Insert an existing master key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key, and within 10 seconds insert the new key and turn it to ON (RUN).
4. The new key has now been programmed.
gM high securiTy key-peps
N Add New Transmitter (Requires one working transmitter)
1. Insert an existing transmitter into the cupholder.
2. Insert the key of the new transmitter into the driver’s side door lock, turning the key to the
unlock position 5 times within 10 seconds. The Driver Information Center will now display,
Ready For Remote #2, 3, 4, or 5.
3. Insert the new transmitter into the transmitter pocket. The transmitter pocket is located
inside the center console under the cupholder. Remove the cupholder to access the transmitter
pocket.
4. Press the ignition button. Once the new transmitter has been programmed, the Driver
Information Center will display that it is ready to program the next transmitter.
5. Remove the new transmitter from the transmitter pocket and press the Unlock button on the
transmitter.
6. Repeat steps 3-5 to program additional transmitters. Press and hold the ignition button for
5 seconds to exit the programming mode.
Originate New Transmitter (No working transmitter exists)
1. Insert the key of the new transmitter into the driver’s side door lock, turning the key to the
unlock position 5 times within 10 seconds. The Driver Information Center will now display,
Remote Learn Pending, Please Wait.
121 TRANSPONDER PROGRAMMING QUICK PROCEDURES
MODEL REFERENCE NAME
Programming Remote Keyless Entry (RKE)
1. The front doors must be closed and unlocked before proceeding.
2. Within 6 seconds, turn the ignition cylinder from OFF to On (RUN) 4 times, with the fourth
time ending in OFF. If the module successfully enters programming mode you will hear a
chime.
3. Within 10 seconds, press any button on the RKE to be programmed. You will hear a chime
to indicate successful programming. Repeat this step for each RKE to be programmed. A
total of 4 RKE’s can be programmed.
4. Exiting the programming mode can be accomplished by turning the ignition cylinder to the
ON (RUN) position, waiting 10 seconds after the final RKE has been programmed, or by
reaching the maximum 8 RKE’s that can be programmed.
2. Wait ten minutes until the Driver Information Center displays, Press Engine Start Button
to Learn and press the ignition button. The Driver Information Center will again display,
Remote Learn Pending, Please Wait.
3. Repeat Step 2 two additional times. After the third time, all existing transmitters for the
vehicle will no longer work the vehicle. Any remaining transmitters can be re-learned . The
Driver Information Center will now display, Ready For Remote #1.
4. Insert the new transmitter into the transmitter pocket. The transmitter pocket is located
inside the center console under the cupholder. Remove the cupholder to access the transmitter
pocket.
5. Press the ignition button. Once the new transmitter has been programmed, the Driver
Information Center will display that it is ready to program the next transmitter.
6. Remove the new transmitter from the transmitter pocket and press the Unlock button on the
transmitter.
7. Repeat steps 4-6 to program additional transmitters. Press and hold the ignition button for
5 seconds to exit the programming mode.