Revel Ultima Studio™ Loudspeaker

More documents

Recommendations

Info

CONNECTIONS (CONTINUED) HORIZONTAL BI-AMPLIFIED SYSTEM Using two amplifier channels, remove the shorting straps from the rear panel; then connect each REVEL ULTIMA STUDIO, as shown in Figure 12. CAUTION: Failure to remove the shorting straps when biamplifying may damage some amplifiers. REVEL ULTIMA STUDIO Rear 0 -.5 +.5 -1 +1 NOTE: If the “gain factor” of the two amplifier channels is not identical, a means of adjusting the input level of at least one of the channels is required. Consult your Revel dealer for specific recommendations. 16 Remove straps for bi-wire or bi-amp Front Tweeter Level Rear Tweeter Level Low Frequency Input High Frequency Input Serial Number xxxx 0 -3 Off Revel Corporation Northridge, California Made in U.S.A. REVEL ULTIMA STUDIO Owner’s Manual 0 0 -.5 +.5 -3 -1 +1 Off Remove straps for bi-wire or bi-amp Front Tweeter Level Rear Tweeter Level Install straps for single-wired operation wht Connector Panel Low Frequency Input High Frequency Input Serial Number xxxx Revel Corporation Northridge, California Made in U.S.A. OUTPUT red Pre-Amplifier (rear) OUTPUT (one channel shown) (Optional “Y” Adaptor) Amplifier (rear) (one channel shown – use for high frequencies) Shorting Straps Removed Amplifier (rear) (one channel shown – use for low frequencies) INPUT INPUT Figure 12. How to connect the REVEL ULTIMA STUDIO in a horizontal bi-amplified system.
Figure 13. REVEL ULTIMA STUDIO level control locations and initial settings. SYSTEM OPTIMIZATION 1. After connecting the REVEL ULTIMA STUDIO loudspeakers, initially set both HIGH FREQUENCY LEVEL controls on both rear panels to the “0” position, as shown in Figure 13. REVEL ULTIMA STUDIO Rear 0 -.5 +.5 -1 +1 Remove straps for bi-wire or bi-amp Low Frequency Input High Frequency Input Serial Number xxxx 0 -3 Off Front Tweeter Level Rear Tweeter Level Revel Corporation Northridge, California Made in U.S.A. 0 -.5 +.5 -1 Front Tweeter Level Set Both Tweeter Level Controls To “0” +1 Remove straps for bi-wire or bi-amp Low Frequency Input High Frequency Input Revel Corporation Northridge, California Made in U.S.A. Connector Panel Rear Tweeter Level 2. Turn on the system power and play a favorite piece of music. Slowly increase the volume to a comfortable level and listen from your main listening position. If desired, experiment with placement (see page 8) to achieve the best overall tonal balance, image specificity, and spaciousness. 3. You may also wish to further adjust the HIGH FREQUENCY LEVEL controls (see Figure 13) for both front and rear tweeters to achieve the most natural sound in your room. Varying the FRONT control will change the high frequency balance and timbre. Varying the REAR control will mainly affect “air” and spaciousness. Do not hesitate to experiment with changes to the front and rear high frequency level controls. Differences in room acoustics often demand different level control settings. 0 -3 Off NOTE: Be certain the corresponding controls are set the same on both left and right channels. REVEL ULTIMA STUDIO Owner’s Manual 17
Page 1 and 2: Revel Ultima Studio Loudspeaker
Page 3 and 4: Figure 1. The REVEL ULTIMA STUDIO l
Page 5 and 6: • A motor system that utilizes ne
Page 7 and 8: Figure 4. A REVEL ULTIMA STUDIO wit
Page 9 and 10: • For best results, make sure the
Page 11 and 12: Figure 7. Tilting a REVEL ULTIMA ST
Page 13 and 14: Figure 9. How to connect the REVEL
Page 15: Figure 11. How to connect the REVEL
Page 19 and 20: Figure 14. Installing a new REVEL U
Page 21 and 22: SPECIFICATIONS Revel utilizes propr
Page 23 and 24: SERVICE INFORMATION In the unlikely

Revel Ultima Studio™ Loudspeaker

Create successful ePaper yourself

Delete template?

Save as template?