Repair Parts and Maintenance Guide | Sloan - Sloan Valve Company

More documents

Recommendations

Info

Manual Flushometers 3 5 4 “L” Dimension PUSH BUTTON ID CHART (All dimensions in inches) 28 Repair Parts and Maintenance Guide Concealed Flushometer (Royal ® ) TAILPIECES, CONTROL STOPS, FLUSH CONNECTIONS AND HANDLE ASSEMBLIES For additional information on tailpieces, control stops, flush connections, and handle assemblies see Showerheads, Parts and Accessories Tab. PARTS LIST Item No. Code No. Part No. Description 1. 0388010 H-730-A 1” RB Wheel Handle Bak-Chek ® Control Stop 0388011 H-730-A 3/4” RB Wheel Handle Bak-Chek ® Control Stop 2. 3301093 A-1013-A Concealed Valve Handle Cap Kit FOR SPECIFYING PROPER LENGTHS FOR ITEMS 3, 4 AND 5, SEE CHART BELOW 3. — C-43-A 3” (76 mm) Push Button Actuator Assembly 4. — C-9-A Blind Nut Push Button Actuator Assembly 5. — B-12-A Lever Actuator Assembly Wall Thickness 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 “L” Dimension 3 3/4 4 3/4 5 3/4 6 3/4 7 3/4 8 3/4 9 3/4 10 3/4 11 3/4 12 3/4 13 3/4 14 3/4 15 3/4 16 3/4 17 3/4 “A” (B-15-A) Filler Rod 1 5/8 2 5/8 3 5/8 4 5/8 5 5/8 6 5/8 7 5/8 8 5/8 9 5/8 10 5/8 11 5/8 12 5/8 13 5/8 14 5/8 15 5/8 “B” (B-6-A) Socket Assembly 2 1/2 3 1/2 4 1/2 5 1/2 6 1/2 7 1/2 8 1/2 9 1/2 10 1/2 11 1/2 12 1/2 13 1/2 14 1/2 15 1/2 16 1/2 B-23 Flange C-2 Pushbutton Wall Thickness 1 2 SEE FLUSH CONNECTIONS IN SHOWERHEADS, PARTS AND ACCESSORIES TAB Specify the “L” dimension for the proper length of the push button assembly “B” “A” B-15-A Filler Rod B-24 Locknut VALVE BODY (NOT SOLD SEPARATELY) C-7 Spring B-6-A Socket Assembly A-6 Coupling A-31 Gasket B-85 Seal Notes: 1. “L” Dimension = Wall thickness (to nearest whole inch) + 2 3/4” 2. 1 1/2” Diameter Hole Opening Required Through Wall B-8-A Plunger B-101 Brass Bushing
TROUBLESHOOTING GUIDE ATTENTION INSTALLERS: With the exception of the control stop inlet, DO NOT USE pipe sealant or plumbing grease on any valve component or coupling! To protect the chrome or special finish of Sloan flushometers, DO NOT USE toothed tools to install or service these valves. Use our A-50 Super-Wrench or other smooth-jawed wrench to secure couplings. Regulations for low consumption fixtures (1.6 gpf/6.0 Lpf closets and 1.0 gpf/3.8 Lpf urinals) prohibit use of higher flush volumes. 1. Flushometer does not function. A. Control Stop or Main Valve is Closed. Open Control Stop or Main Valve. B. Handle or Push Button Assembly is worn. Install Sloan Handle Repair Kit (C-70-A) or replace handle or push button. C. Relief Valve is worn. Replace Inside Parts Kit. 2. Insufficient volume of water to adequately siphon fixture. A. Control Stop not open enough. Adjust Control Stop for desired delivery of water. B. Urinal flushometer Parts inside a Closet flushometer. Replace Inside Urinal Parts with proper Closet flushometer Parts. C. Low Consumption flushometer installed on a non-Low Consumption fixture. Replace A-41-A Inside Parts Kit with A-38-A Water Saver Kit. D. Water Saver Kit installed in old, non-Water Saver bowl. Position Refill Head A-170 so that SIDE 1 is in the UP Position. E. Inadequate volume or pressure at supply. If no gauges are available to properly measure supply pressure or volume of water at the flushometer, then remove the Relief Valve from the Inside Parts Kit, reassemble the flushometer and open the Control Stop. If the fixture siphons, more water volume is required. If a 3.5 gpf Inside Parts Kit is installed in the flushometer, then first flip the Refill Head (under the Diaphragm) to obtain a 4.5 gpf volume. If this volume is still inadequate, remove the Flow Ring from the Guide to obtain a 6.5 gpf Kit. If additional flow is still required, try a Low Pressure Guide Kit A-175-A (#0301104). IMPORTANT: Laws and regulation prohibit the use of higher flushing volumes than listed on fixture or flushometer. If fixture does not siphon or if a Low Consumption fixture is installed, or if the above steps do not prove satisfactory, steps must be taken to increase the pressure and/or supply. 3. Flushometer closes off immediately. A. Ruptured or damaged Diaphragm. Install Inside Parts Kit to correct problem and update flushometer. B. Enlarged By-pass orifice from corrosion or damage. Install Inside Parts Kit to correct problem and update flushometer. 4. Length of flush is too short (Short Flushing). A. Diaphragm Assembly and Guide Assembly are not hand-tight. Screw the two assemblies hand-tight. B. Enlarged By-pass orifice from corrosion or damage. Install NEW Inside Parts Kit to correct problem and update flushometer. C. A-19-AU (Black) Urinal Relief Valve in Closet flushometer. Replace Relief Valve with A-19-AC (White) Closet Relief Valve. D. A-41-A Low Consumption Kit installed in non-Low Consumption fixture. Replace with proper Inside Parts Kit. E. Handle Assembly is worn. Install Handle Repair Kit C-70-A or replace the Handle. 29 Repair Parts and Maintenance Guide Concealed Flushometer (Royal ® ) 5. Length of flush is too long (Long Flushing) or fails to close off. A. Relief Valve is not seating properly or By-pass orifice is clogged because of foreign material, or By-pass orifice is closed by an invisible gelatinous film from “over-treated” water. Disassemble the working parts and wash thoroughly. NOTE: SIZE OF ORIFICE IN THE BY-PASS IS EXTREMELY IMPORTANT FOR PROPER METERING OF WATER INTO THE UPPER CHAMBER OF THE FLUSHOMETER. DO NOT ENLARGE OR DAMAGE THIS ORIFICE. REPLACE INSIDE KIT IF CLEANING DOES NOT CORRECT PROBLEM. B. Line pressure has dropped and is not sufficient to force Relief Valve to seat. Shut off all control stops until pressure has been restored, then open them again. C. A-19-AC (White) Closet Relief Valve has been used in a 1 or 1-1/2 gpf Urinal. Replace with A-19-AU (Black) Relief Valve. D. Inside Cover is cracked or damaged. Replace the Inside Cover (A-71). 6. Chattering noise in flushometer. A. The A-156-A Segment Diaphragm has been installed upside-down. Replace the Segment Diaphragm to the proper position as instructed by markings on the Diaphragm. B. The Inside Cover has become distorted from wear, freezing or abuse. Replace Inside Cover. 7. Leaking at Handle or Push Button Assembly. A. The B-39 Seal is worn or deteriorated. Install new B-39 Seal. NOTE: The B-39 Seal will easily slide onto the B-40 Bushing if it is wet. B. Handle gasket has been omitted. Install A-31 Handle Gasket or Sloan Handle Repair Kit (C-70-A). C. Valve Handle Bushing is worn. Install Sloan Handle Repair Kit (C-70-A). CARE AND CLEANING INSTRUCTIONS DO NOT use abrasive or chemical cleaners to clean flushometers, they may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with a clean towel or cloth. While cleaning the bathroom tile, the exposed flushometer handle, button or piping should be protected from any splattering of cleaner. Acids and cleaning fluids can discolor or remove chrome plating. When assistance is required, please contact Sloan Technical Support at: 1-888-SLOAN-14 (1-888-756-2614). Manual Flushometers
Page 1 and 2: Repair Parts and Maintenance Guide
Page 3 and 4: Product Identification Guide Flusho
Page 5 and 6: 5 Repair Parts and Maintenance Guid
Page 7 and 8: Faucet Identification IDENTIFY YOUR
Page 9 and 10: IDENTIFY YOUR SLOANSTONE LAVATORY S
Page 11 and 12: Tailpiece Control Stop and Caps TAI
Page 13 and 14: TROUBLESHOOTING GUIDE ATTENTION INS
Page 15 and 16: 2 7 4 5 6 1 3 15 Repair Parts and M
Page 17 and 18: COVER HANDLE COUPLING HANDLE ASSEMB
Page 19 and 20: The repair kits and parts listed on
Page 21 and 22: TROUBLESHOOTING GUIDE ATTENTION INS
Page 23 and 24: PARTS LIST FOR SERIES 900 ® CONCEA
Page 25 and 26: HY-49-A (0318049) METAL PARTITION P
Page 27: TROUBLESHOOTING GUIDE (CONTINUED) 7
Page 31 and 32: TROUBLESHOOTING GUIDE IMPORTANT: Th
Page 33 and 34: Piston Cover Color Piston Color Bar
Page 37 and 38: K L HANDLE COVER BODY HANDLE COUPLI
Page 39 and 40: 39 Repair Parts and Maintenance Gui
Page 41 and 42: PARTS LIST—DOLPHIN ® FLUSHOMETER
Page 43 and 44: ITEM 9A. SLIP JOINT GASKETS AND RIN
Page 45 and 46: 7 Concealed Urinal Models and TMO M
Page 47 and 48: 1 TO SOLENOID (SEE PAGE 46) 6 2 3 4
Page 49 and 50: ROYAL ® ESS (ITEM 24) REPAIR KIT 4
Page 51 and 52: SENSOR REPLACEMENT NOTE: The EL-150
Page 53 and 54: 8 5A 7 10 4B 12 1 4A 9A/9B 6A 6D 6B
Page 55 and 56: 22 9 3 4 2 12A 12 12 13A/B 12B 12 1
Page 57 and 58: 1 2 57 Repair Parts and Maintenance
Page 59 and 60: 9 1B 1A 4 12 14 2 15 13 3 15A 5 6 7
Page 61 and 62: A-3 Body 25 26 Earlier model with E
Page 63 and 64: SOLENOID REPLACEMENT Code No. Part
Page 65 and 66: TROUBLESHOOTING AND MAINTAINING THE
Page 67 and 68: 9 13A 9A 10 22 21 23 16B 16A 14 19
Page 69 and 70: FLEX TUBE DIAPHRAGM KITS REGULATORS
Page 73 and 74: LOCKING RING COVER BODY FLUSH CONNE
Page 75 and 76: TROUBLESHOOTING AND MAINTAINING THE
Page 77 and 78: ADJUSTMENT PROCEDURES Mode A The SM
Page 79 and 80:
TO CHANGE ACTIVATION DISTANCE FOR T
Page 81 and 82:
ITEM 10. FLEX TUBE DIAPHRAGM KIT SE
Page 83 and 84:
TROUBLESHOOTING AND MAINTAINING THE
Page 85 and 86:
ITEM 8. FLEX TUBE DIAPHRAGM KIT SEL
Page 87 and 88:
1. Sensor Flashes Continuously Only
Page 89 and 90:
TROUBLESHOOTING GUIDE NOTE: Upon de
Page 91 and 92:
SH-1009-A REPAIR KIT FOR AC-450 MOD
Page 93 and 94:
CONTROL STOP AND REPLACEMENT PARTS
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
THE “COMMON STOP” In 1996, Sloa
Page 101 and 102:
H-5 GROUND JOINT TAILPIECE CONNECTI
Page 103 and 104:
1A 1B 2A 8 10 7 6 3 5 4 1A 1B 2B 9A
Page 105 and 106:
STEP 3 — INSTALL VACUUM BREAKER F
Page 107 and 108:
3” Push Button For Exposed Royal
Page 109 and 110:
OBSOLETE Pedal Handle Push Button F
Page 111 and 112:
Complete Flush Connection Assemblie
Page 113 and 114:
Complete Flush Connection Assemblie
Page 115 and 116:
Outlets (continued) Code No. Part N
Page 117 and 118:
BUMPERS Item No. Code No. Part No.
Page 119 and 120:
SWEAT SOLDER KITS Item No. Code No.
Page 121 and 122:
EFX-1XX SERIES EFX-2XX SERIES 6D 8
Page 123 and 124:
Factory setting is appropriate for
Page 125 and 126:
REPLACE SPRAY INSERT NOTE: Turning
Page 127 and 128:
TROUBLESHOOTING GUIDE 1. Red LED in
Page 129 and 130:
OPERATION As the user’s hands ent
Page 131 and 132:
REPLACING THE SOLENOID STRAINER (FI
Page 133 and 134:
Page 135 and 136:
OPERATION As the user’s hands ent
Page 137 and 138:
REPLACING THE SOLENOID STRAINER (FI
Page 139 and 140:
Page 141 and 142:
OPERATION OF FAUCET A continuous am
Page 143 and 144:
LED DISPLAY DIAGNOSTIC CODES Functi
Page 145 and 146:
AUTO RANGE ADJUSTMENT Press button
Page 147 and 148:
ELF-10 ESF-20 ESF-30 ELF-10 ESF-20
Page 149 and 150:
4A 4B 11 8 OLD-STYLE FAUCETS ETF-80
Page 151 and 152:
ETF-500 New Base Gasket The new bas
Page 153 and 154:
3 4B ETF-610 5 6 7 7 6 12 2 1B 1C 4
Page 155 and 156:
2B 3 3B ETF-770 Old-Style Faucets E
Page 157 and 158:
4 1A 6 5 8 1C 4 3 2A 13 2B 1B 1C 9
Page 159 and 160:
2A/2B 3 4 5 4 6 1 10 11 7 8 9 159 R
Page 161 and 162:
TROUBLESHOOTING GUIDE Note: Remove
Page 163 and 164:
TROUBLESHOOTING GUIDE OPERATION 1.
Page 165 and 166:
TROUBLESHOOTING GUIDE OPERATION 1.
Page 167 and 168:
167 Repair Parts and Maintenance Gu
Page 169 and 170:
TROUBLESHOOTING GUIDE 1. Faucet doe
Page 171 and 172:
AUTO RANGE ADJUSTMENT Press button
Page 173 and 174:
9 3A 3B 5 8 10 OLD SOLENOID 10 1 4
Page 175 and 176:
†† TO MOUNT FAUCET ON A SURFACE
Page 177 and 178:
3 4B EBF-615 EBF-650 10B 10E EBF-61
Page 179 and 180:
3 4A 8A 8C 8E 9 10 EBF-625 EBF-655
Page 181 and 182:
8 Optional Trim Plate Kits 9 1A 15
Page 183 and 184:
1A/1B 4 3A 3B 3C 3D 5 9 11 6 13 14
Page 185 and 186:
OBSOLETE OBSOLETE 185 Repair Parts
Page 187 and 188:
1A/1B 4 10 3A 3B 3C 3D 5 13 14 EAF-
Page 189 and 190:
10 5 EAF-750 9 1 2 7 8 4 6 3 189 Re
Page 191 and 192:
I.Q.-CLICK FEATURE 1. CONTINUOUS RU
Page 193 and 194:
2C 2D 9 SF-2100 SF-2150 11 1A 12A 3
Page 195 and 196:
4 10A 3 2 5A/5B 10 2A 2B 2C 10B 10C
Page 197 and 198:
2 2A 2B 2C 2D 2E 11A 5A/5B 9 11 11B
Page 199 and 200:
Description Sloan offers a variety
Page 201 and 202:
EAF SERIES - SF-2100/SF-2150/SF-230
Page 203 and 204:
TROUBLESHOOTING GUIDE 1. Unit does
Page 205 and 206:
TROUBLESHOOTING GUIDE FOR NEW EHD H
Page 207 and 208:
TROUBLESHOOTING GUIDE 1. Poor Flush
Page 209 and 210:
TROUBLESHOOTING GUIDE 1. Water does
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
ITEM NO. 1 — DOUBLE STATION LAVAT
Page 219 and 220:
4 5 ITEM NO. 8 - DOUBLE STATION LAV
Page 221 and 222:
PARTS LIST—EW-42000 SINK Item No.
Page 223 and 224:
TROUBLESHOOTING GUIDE 1. No water f
Page 225 and 226:
EW-62000 Double Station Sensor Acti
Page 227 and 228:
EW-63000 Triple Station Sensor Acti
Page 229 and 230:
2 7 3 13 12 1 9 32 8 11 22 25 21 28
Page 231 and 232:
24 2 1 7 13 9 31 23 8 19 22 14 21 2
Page 233 and 234:
EWF-42000 Double Station 11A 11B 11
Page 235 and 236:
ELB-51000 Single Station ELB-52000
Page 237 and 238:
ELC-41000 Single Station ELC-42000
Page 239 and 240:
6 4 5 7 239 Repair Parts and Mainte
Page 241 and 242:
2 XCW OPTION 9 10 4 STANDARD 7 9 8
Page 243 and 244:
NOTE: Cartridge Assembly can be rot
Page 245:
PRODUCT VARIATION SUFFIXES FLUSHOME
show all

Repair Parts and Maintenance Guide | Sloan - Sloan Valve Company

Create successful ePaper yourself

Delete template?

Save as template?