Engine Air Cleaners, Intake Accessories and ... - Giro Servicios CA

Recommendations

Info

Intake Accessories Exhaust Ejectors A Donaldson exhaust ejector mounts as a stack at the end of exhaust system (stack caps or extension tubes may be added). The ejector is used with a Donaldson Donaspin pre-cleaner or Strata system – typically used in offhighway equipment to extend air filter life. To fit your space and design requirements, three exhaust ejector styles are available. All are constructed of heavygauge, aluminized steel. Select the appropriate ejector by the intake airflow (CFM) of your engine. Expanded I.D. End Style Expanded End Style Compact Style Standard Style How It Works Engine Scavenge Ejector Exhaust Part Intake -- Inlet I.D. -- Tube O.D. --- Length --- Flow Rate (CFM) Number CFM inch mm inch mm inch mm Min.1 Max.2 H002129 3 500-715 5.17 131 1.50 38 29.50 749 1270 1800 H002131 4 780-1110 6.19 157 2.00 51 32.50 826 1985 2800 H002132 4 1040-1475 6.19 157 2.00 51 32.50 826 2625 3715 Donaspin Pre-Cleaner Cleaned Air Intake Air Silicone Hose Scavenge Line The Donaspin pre-cleaner uses a spinning motion of the airstream to force dirt and debris to the outside wall of the pre-cleaner body. The dirt and debris are forced to the bottom of the pre-cleaner and expelled by the secondary airflow developed by the ejector. EXPANDED STYLE INSTALLATION Ejector MaxGrip Clamp Muffler Outlet End Exhaust Air 82 Engine Air Cleaners, Accessories & Service Parts www.donaldson-filters.com Ejector Expanded I.D. End Simplifies installation - requires less parts to install No need for separate connector! Fits over most standard muffler outlet tubes Adds only 4" (102 mm) to 8" (203 mm) H20 (.3" to .6" Hg.) to exhaust backpressure Standard Can be used with any pre-cleaner style Adds only 4" (102 mm) to 8" (203 mm) H20 (.3" to .6" Hg.) to exhaust backpressure Compact Used primarily on agricultural equipment Adds 10" (254 mm) to 15" (381 mm) H20 (.75" to 1.1" Hg.) to exhaust backpressure
Standard Style Engine Scavenge Ejector Exhaust Part Intake -- Inlet I.D. -- Tube O.D. --- Length --- Flow Rate (CFM) Number CFM inch mm inch mm inch mm Min.1 Max.2 H0010323 245-350 3.02 77 1.50 38 17.50 445 620 873 H0010333 310-440 4.02 102 1.50 38 24.00 610 785 1110 H0010343 385-545 4.02 102 1.50 38 24.00 610 970 1375 H0010353 500-715 5.03 128 1.50 38 29.50 749 1270 1800 H0010384 1040-1475 6.04 153 2.00 51 32.50 826 2625 3715 H0010394 1285-1820 6.04 153 2.00 51 32.50 826 3235 3875 Compact Style Engine Scavenge Ejector Exhaust Part Intake -- Inlet I.D. -- Tube O.D. --- Length --- Flow Rate (CFM) Number CFM inch mm inch mm inch mm Min.1 Max.2 H0012785 165-215 2.77 70 1.25 32 9.75 248 415 545 H001280 225-335 3.52 89 1.25 32 12.50 318 570 850 H0012795 300-390 3.02 77 1.25 32 10.80 274 760 990 H001281 370-480 4.02 102 1.25 32 14.38 365 935 1215 H0012845 450-590 4.02 102 1.25 32 14.38 365 1140 1500 1 - Minimum exhaust flow based on 20" of water dead head vacuum 2 - Maximum exhaust flow based on 40" of water dead head vacuum 3 - Use 3-ply Silicone Scavenge Hose (1.50"I.D., 3 ft. length) P171378 and Lined Hose Clamp P115200 4 - Use 3-ply Silicone Scavenge Hose (2.00" I.D., 3 ft. length) P171381 and Lined Hose Clamp P115200 5 - Use 3-ply Silicone Scavenge Hose (1.25" I.D., 3 ft. length) P171376 and Lined Hose Clamp P532924 Exhaust Gas Temperature of 900° F assumed The exhaust ejector check valve prevents backflow of damaging exhaust gases by way of an internal hinge flap. Add an ejector check valve when configuring the intake system to expel filtered contaminant through the exhaust system. Mounts horizontally (see installation diagrams) Durable, non-corrosive metal construction No servicing required Exhaust Ejectors & Check Valves Ejector Check Valve Prevents Exhaust Backflow H001023 H000722 STANDARD OR COMPACT INSTALLATION www.donaldson-filters.com Engine Air Cleaners, Accessories & Service Parts 83 Ejector MaxGrip Clamp O.D. Connector MaxGrip Clamp Muffler Outlet End Check Valve Installation The illustrations are side views of two-stage air cleaners, showing the position of the check valve. A 3" (76mm) inner diameter rubber reducing elbow or hump reducer is required for installation. See pages 75-77 for options. Installation on Cyclopac Installation on Donaclone Intake Accessories
Page 1 and 2:
Engine Air Cleaners, Intake Accesso
Page 3 and 4:
Donaldson filters are built to prov
Page 5 and 6:
Innovative Engineering Air Cleaners
Page 7 and 8:
Donaldson Filters Lasting Value Don
Page 9 and 10:
Air Cleaner Finishes ...Donaldson a
Page 11 and 12:
The objective... 1. Minimize the nu
Page 13 and 14:
y Air Flow Pattern A = Air in the E
Page 15 and 16:
Engine Data The data shown in this
Page 17 and 18:
-- Exhaust -- Engine Intake Temp. F
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
RadialSeal A Better Approach To Sea
Page 25 and 26:
EPG for Light Dust Conditions Provi
Page 27 and 28:
EPG Service Parts G110119 cover ...
Page 29 and 30:
Airflow pattern “A” Air in the
Page 31 and 32:
FPG Offers Advanced Sealing Technol
Page 33 and 34: Airflow pattern “G” Air in the
Page 35 and 36: Donaldson offers two styles of moun
Page 37 and 38: FRG: Superior Protection for Larger
Page 41 and 42: FRG Service Parts Style A Access Co
Page 43 and 44: Axial Seal Air Cleaners Axial seal
Page 45 and 46: EBA Konepac Service Parts (KPII sty
Page 49 and 50: EBB Provides Versatile Mounting Cap
Page 51 and 52: Horizontal Mount, Integral Vacuator
Page 53 and 54: STG Donaclone: Field Proven & Relia
Page 55 and 56: STG Donaclone �� for Heavy D
Page 57 and 58: STG Service Parts Tubular Inlet Sty
Page 59 and 60: SRG Donaclone �� for Heavy Dust
Page 61 and 62: SRG29 Service Parts Body Gasket Str
Page 63 and 64: STB Strata �� for Heavy Dust Co
Page 65 and 66: When spec’ing a DuraLite Air Clea
Page 67 and 68: Donaldson Intake Accessories The ac
Page 69 and 70: Horizontal, In-Line Moisture Skimme
Page 71 and 72: Mounting Bands for Air Cleaners Man
Page 73 and 74: Inlet Hood - Style C Inlet Hoods Fi
Page 75 and 76: The lnformer for Graduated, Contin
Page 77 and 78: Service Gauge for Instrument Panel
Page 79 and 80: These flexible rubber adapters and
Page 81 and 82: Rubber Products Rubber Straight Hum
Page 83: Replacement Vacuator Valves Replace
Page 87 and 88: Air Stack Extensions Helps Extend F
Page 89 and 90: Performance Curves Dimensional Spec
Page 91 and 92: Service Parts by Air Cleaner Model
Page 93 and 94: Air Cleaner Part No./Style Descript
Page 95 and 96: Air Cleaner Part No./Style Descript
Page 97 and 98: Proper Air Cleaner Service is Essen
Page 99 and 100: Filtration Micron ratings are commo
Page 101 and 102: Will-Fit Filters are Often Won’t
Page 103 and 104: Don’t remove filter for inspectio
Page 105 and 106: Remove the old 1 filter gently “B
Page 107 and 108: Axial Seal Service Instructions Two
Page 109 and 110: Positioning the Strata Pre-Cleaner
Page 111 and 112: Index of All Parts by Part Number W
Page 113 and 114: Part Page No. No. Product Descripti
Page 116: Your Your Donaldson Donaldson Distr
show all

Engine Air Cleaners, Intake Accessories and ... - Giro Servicios CA

Create successful ePaper yourself

Delete template?

Save as template?