Heat Shrinkable Moulded Shapes Brochure - RB Racing

More documents

Recommendations

Info

2.2 46 Insulation Bulbous Boots and Transitions 4-Way Outlet <strong>Shapes</strong>, VG style • Helashrink 400 Series This style provides cable strain relief and mechanical protection at harness transition points, all outlets are clearly marked to aid orientation on installation. a: Expanded form (supplied) Type Designation as per VG-Norm ØH min. a 403-1-G supplied / fully recovered. ØH max. b Sizes and Type Table ØJ/K/L/N min. a b: Fully recovered form (after heating) ØJ/K/L/N max. b P ± 10% R ± 10% S ± 10% HW ± 20% 411-1 VG95343T08E002A 19.0 10.0 9.5 5.5 36.1 35.6 32.0 1.8 1.0 403-1 VG95343T08E004A 27.0 13.0 13.0 7.0 51.8 49.0 45.0 2.5 1.0 413-1 VG95343T08E005A 38.6 19.0 19.0 10.0 74.9 75.0 65.3 1.8 1.0 All dimensions in mm. Subject to technical changes. W ± 10% Combinations ″On request″ Standard combinations Adhesive Material Article-No. Type B7 G H L J 404-11180 411-1-G WM250 √ √ √ - √ 404-03180 403-1-G W8 √ √ √ - √ 404-13180 413-1-G W24 √ √ √ √ √ V9500 √ √ √ - - HMT200A √ √ √ - - W21 - - √ - - Without Adhesive √ √ √ √ √
4-Way Outlet <strong>Shapes</strong>, Breakout Boots • Helashrink 400 Series, in line, low voltage Branching parts are used for easy, timesaving insulation of the branch point of a cable where it is split into single wires.They are manufactured from a tough cross-linked flame retarded polyolefin. Branching parts with hot melt adhesive also serve to relieve the mechanical tension in cable harnesses whilst providing excellent IP ratings. !For Material / Adhesive selection and other information please refer to page 10. 442-1 supplied / fully recovered. ØH a: Expanded form (supplied) b: Fully recovered form (after heating) Type ØH min. a ØH max. b Combinations ″On request″ Adhesive Material B7 G H B8 J W √ √ √ √ √ W2 √ √ √ √ - W24 √ √ √ - √ V9500 √ √ - - √ HMT200A √ √ - √ √ W21 - - √ - √ Without Adhesive √ √ √ √ √ Insulation Bulbous Boots and Transitions ØJ min. a ØJ Sizes and Type Table ØJ max. b P ± 10% R ± 10% HW ± 20% S JW ± 20% S nom 442-1 28.0 9.0 9.0 1.8 78.0 17.0 2.7 2.0 20.0 434-2 23.0 11.0 8.0 2.8 78.0 22.0 1.6 1.6 18.0 443-1 35.0 12.0 15.0 3.0 132.0 26.0 3.0 2.5 22.0 408-2 35.0 12.0 15.0 3.0 95.0 24.0 2.5 2.0 22.0 435-2 32.0 20.3 13.0 4.8 93.5 28.5 2.9 2.9 27.0 409-2 47.4 22.9 21.5 6.4 165.0 38.1 4.1 3.3 38.1 418-4 60.0 22.9 30.0 6.4 202.0 38.1 4.1 3.3 38.1 436-2 45.0 24.9 21.0 7.1 99.0 34.0 4.5 4.5 39.0 437-1 60.0 25.4 26.0 8.9 240.0 48.0 4.5 4.5 43.0 438-2 68.0 35.6 31.0 13.5 141.5 42.5 4.5 4.5 54.0 444-2 35.6 95.0 35.6 12.5 240.0 55.0 4.0 3.5 50.8 All dimensions in mm. Subject to technical changes. Standard combinations Article-No. Type 404-42022 442-1-B8W 404-34017 434-2-G 404-43002 443-1-B8 404-08022 408-2-B8W2 404-35007 435-2-J 404-09021 409-2-B8W2 404-18020 418-4-B8W2 404-37001 437-1-B7 404-38008 438-2-J 404-44022 444-2-B8W2 2.2 47
Page 1 and 2: Heat Shrinkable Moulded Shapes Insu
Page 3 and 4: Right Angle Shapes, VG style • He
Page 5 and 6: At your service wherever - and when
Page 7 and 8: Contact If you have a particular pr
Page 9 and 10: 1 Technical Introduction 1 Technica
Page 11 and 12: 3.2 Adhesive To maximise environmen
Page 13 and 14: Bulbous Boots and Transitions 4-Way
Page 15 and 16: Adhesives for Heat Shrinkable Mould
Page 17 and 18: Insulation Material & Adhesive Comb
Page 19 and 20: Insulation Material & Adhesive Comb
Page 21 and 22: Heat Shrinkable Moulded Shapes 4-Wa
Page 23 and 24: Low Profile Shim Boots • Helashri
Page 25 and 26: Low Profile Right Angle Boots • H
Page 27 and 28: Low Profile Transition Boots • He
Page 29 and 30: Bottle Shapes, VG style • Helashr
Page 31 and 32: Bottle Shapes, MIL style • Helash
Page 33 and 34: Bottle Shapes • Helashrink 100 Se
Page 35 and 36: Long Outlet Shape, VG style • Hel
Page 37 and 38: Long Outlet Shapes • Helashrink 1
Page 39 and 40: Bottle Shapes, VG style • Helashr
Page 41 and 42: 2-Way Outlet Shapes • Helashrink
Page 43 and 44: 2-Way Outlet Shapes, Breakout Boots
Page 45: 3-Way Outlet Shapes, Breakout Boots
Page 51 and 52: Right Angle Shapes, VG style • He
Page 53 and 54: Right Angle Shapes • Helashrink 1
Page 55 and 56: Right Angle Shapes, VG style/MIL st
Page 57 and 58: T-Shapes, VG style • Helashrink 1
Page 59 and 60: T-Shapes, VG style • Helashrink 1
Page 61 and 62: Double T-Shapes • Helashrink 1310
Page 63 and 64: Connector Cover for Min-D Series
Page 65 and 66: Angle Shapes • Helashrink 1800 Se
Page 67 and 68: Locating Bushes • Helashrink 1760
Page 69 and 70: 3 Cable Management Products Page 3.
Page 73 and 74: End Caps • Helashrink 1600 Series
Page 75 and 76: Heat Shrinkable Tubing 2:1 - Fluoro
Page 77 and 78: Heat Shrinkable Tubing 2:1 - Elasto
Page 79 and 80: Constant Force Spring Adaptor • Z
Page 81 and 82: Hot Melt Tape for Heat Shrinkable T
Page 83 and 84: 4 Appendix Page 4.1 HellermannTyton
Page 85 and 86: Description Description VG-Norm Hel
Page 87 and 88: HellermannTyton Shapes for use with
Page 89 and 90: Appendix Notes 4.2 89
Page 95 and 96: 1. Interpretation 1.1 In these Cond
Page 97 and 98:
Appendix General Terms and Conditio
Page 99 and 100:
• Operating Temperature -75°C to
show all

Heat Shrinkable Moulded Shapes Brochure - RB Racing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?