Heat Shrinkable Moulded Shapes Brochure - RB Racing

More documents

Recommendations

Info

3.4 80 Insulation Adhesives Two-component Adhesive for Heat Shrinkable Tubing and Shapes • V9500 Dosing Gun The V9500 dosing gun allows for clean processing and individual metering. It is employed in conjunction with the dual cartridges 627-95002. The V9500 lockable cartridges are available with or without the processing set. The processing set is available in two versions (see table for contents). The cartridges can be re-used, even after a lapse of several days, because the closure prevents the adhesive from hardening. • V9500 This high performance, VG-approved, two part epoxy adhesive has been developed to meet the military requirements associated with heat shrinkable components for wire and cable harnesses. It has very good resistance to most solvents and fuels, even at higher temperatures. The two part epoxy adhesive is available in two different packages. When heat is applied during the shrinking of the moulded shape, the two part components react, producing a high performance bond. Material Epoxy resins (EP) Colour Black (BK) Curing Temperature +135 °C Curing Time 24 hours at +25 °C, 2 hours at +85 °C Operating Temperature -75 °C to +150 °C Specification VG 95343 T15 DA The V9500 applicator gun guarantees the clean and precise coating of special fittings. Technical Table Article-No. Type Designation as per VG-Norm Content 627-95001 V9500 epoxy adhesive kit VG 95343 T15 A 001 A 1 x dual cartridge (50g), 5 x mixing pots, 5 x mixing sticks, 5 x emery papers 627-95002 V9500 Duo pack VG 95343 T15 A Two component adhesive cartridge 627-95003 V9500 Applicator gun VG 95343 T15 DA Applicator gun 627-95004 V9500 Nozzle VG 95343 T15 MA Mixing nozzle Subject to technical changes. Two-component epoxy adhesive V9500. Material Data Please note! Not all products listed on this page may have this approval. For product specific approvals please refer to the Appendix. halogenfree
Hot Melt Tape for Heat Shrinkable Tubing and Shapes • HMT200A Features and Benefits The hot melt tape flows when heated and provides permanent airtight and watertight seals. Application Designed for use with heat shrinkable sleeving and mouldings. Application Method 1. Clean and prepare the bonding areas.* 2. Wrap the tape around the part and overlap.* 3. Put the tubing or heat shrinkable shape over the tape and shrink down.* *As per installation guide HMT200A HMT200A tape. Adhesive tape HMT200A for sealing against humidity. Material Data Material Ethylenevinylacetate (EVA) Colour Transparent (CL) Operating Temperature -55 °C to +105 °C Technical Table Melting Point starting from +95 °C Thickness Width Reel Length Article-No. Type (T) (W) (m) 354-02259 HMT200A 0.25 25.0 50 354-02260 HMT200A 0.25 25.0 10 All dimensions in mm. Subject to technical changes. halogenfree Insulation Adhesives � 3.4 81
Page 1 and 2:
Heat Shrinkable Moulded Shapes Insu
Page 3 and 4:
Right Angle Shapes, VG style • He
Page 5 and 6:
At your service wherever - and when
Page 7 and 8:
Contact If you have a particular pr
Page 9 and 10:
1 Technical Introduction 1 Technica
Page 11 and 12:
3.2 Adhesive To maximise environmen
Page 13 and 14:
Bulbous Boots and Transitions 4-Way
Page 15 and 16:
Adhesives for Heat Shrinkable Mould
Page 17 and 18:
Insulation Material & Adhesive Comb
Page 19 and 20:
Insulation Material & Adhesive Comb
Page 21 and 22:
Heat Shrinkable Moulded Shapes 4-Wa
Page 23 and 24:
Low Profile Shim Boots • Helashri
Page 25 and 26:
Low Profile Right Angle Boots • H
Page 27 and 28:
Low Profile Transition Boots • He
Page 29 and 30: Bottle Shapes, VG style • Helashr
Page 31 and 32: Bottle Shapes, MIL style • Helash
Page 33 and 34: Bottle Shapes • Helashrink 100 Se
Page 35 and 36: Long Outlet Shape, VG style • Hel
Page 37 and 38: Long Outlet Shapes • Helashrink 1
Page 39 and 40: Bottle Shapes, VG style • Helashr
Page 41 and 42: 2-Way Outlet Shapes • Helashrink
Page 43 and 44: 2-Way Outlet Shapes, Breakout Boots
Page 51 and 52: Right Angle Shapes, VG style • He
Page 53 and 54: Right Angle Shapes • Helashrink 1
Page 55 and 56: Right Angle Shapes, VG style/MIL st
Page 57 and 58: T-Shapes, VG style • Helashrink 1
Page 59 and 60: T-Shapes, VG style • Helashrink 1
Page 61 and 62: Double T-Shapes • Helashrink 1310
Page 63 and 64: Connector Cover for Min-D Series
Page 65 and 66: Angle Shapes • Helashrink 1800 Se
Page 67 and 68: Locating Bushes • Helashrink 1760
Page 69 and 70: 3 Cable Management Products Page 3.
Page 73 and 74: End Caps • Helashrink 1600 Series
Page 75 and 76: Heat Shrinkable Tubing 2:1 - Fluoro
Page 77 and 78: Heat Shrinkable Tubing 2:1 - Elasto
Page 79: Constant Force Spring Adaptor • Z
Page 83 and 84: 4 Appendix Page 4.1 HellermannTyton
Page 85 and 86: Description Description VG-Norm Hel
Page 87 and 88: HellermannTyton Shapes for use with
Page 89 and 90: Appendix Notes 4.2 89
Page 95 and 96: 1. Interpretation 1.1 In these Cond
Page 97 and 98: Appendix General Terms and Conditio
Page 99 and 100: • Operating Temperature -75°C to
show all

Heat Shrinkable Moulded Shapes Brochure - RB Racing

Create successful ePaper yourself

Delete template?

Save as template?