System # 2010

More documents

Recommendations

Info

Chipbox is a furniture lock that can be opened touchlessly an electronic chip. The spring mechanism is driven by an electric motor 3V. Suffi cient electric power to assure 20,000 openings is supplied by a replaceable lithium cell 3V. Then the lock signals that the cell should be replaced. If this signal goes unheard, the lock opens with the residual power and remains opened until the used cell is replaced by a new one. 100 ELECTRONIC CHIP BOX LOCK Up to 50 data carriers proxy 125 KHz can be programmed on each lock and may be deleted at any time. Although the programming is really uncomplicated, chipbox offers a maximum protection against its opened by non-authorized persons. The scope of delivery covers a striking plate equipped with a spring that automatically pudhes the door open after the electronic unlocking. Chipbox may also easily be installed subsequently into the furniture.
PROGRAMMING INSTRUCTION ELECTRONIC CHIP BOX LOCK The lock automatically recognizes the programming card and the data carrier included in the scope of delivery. However, programming can be changed at any time, as described in the following. Programming of the card Press the programming key (1) of the lock for three seconds until you hear a long acoustic signal followed by a ticking lasting for approx. 7 seconds. During the ticking signal hold the programming card (8) to the identifi cation zone (3) until you hear an acoustic signal of recognition. Now the card is programmed. Programming of the data carrier Hold the programming card (8) once to the identifi cation zone (3). A ticking lasting for 7 seconds is to be heard. During the ticking hold the data carrier (7) to the identifi cation zone (3) for read-in until you hear an acoustic signal of recognition. Now the data carrier is programmed. Control the data carrier as to its functioning Hold the data carrier (7) to the identifi cation zone (3) until you hear an acoustic recognition signal and until the spring advances. Hold the data carrier (7) once again tho the identifi cation zone (3) until you hear an acoustic recognition signal and the opening interval is started. Delete individual programmed data carriers Hold the programming card (8) once to the identifi cation zone (3) until you hear a ticking lasting for approx. 7 seconds. Hold the data carrier (7) for deletion to the identifi cation area during the ticking until hear a recognition signal. Now the data carrier is deleted. Delete all programmed data carriers Hold the programming card (8) to the identifi cation zone (3) until you hear four short acoustic signals followed by a long recognition signal. Now all the programmed data carrier are deleted und the spring has returned into opening position. Activate or deactivate the acoustic signal Push the programming key (1) for one second. All settings, for which the programming key (1) is not needed, can be made with the lock already mounted. The electronics of the lock is able to read the data carrier and the programming card even through materials of up to 20 mm thickness. Warning: The correct functioning can only be guaranteed if the lock is mounted on non-conducting materials (wood, synthetic material) with a max. thickness of 2 0 mm. In case of a higher thickness, with metal doors or doors with a metal application, anantenna has to be installed. 1 programming key 2 lateral part 4 2 3 identifi cation zone 4 spring 5 bolting holes 6 battery chamber 8 7 7 data carrier 8 programming card Battery removal Open the battery chamber (6), remove the used battery and, in order to avoid a malfunction, wait approx. 30 seconds before inserting the new battery. Take care of the polarity (+/-) as indicated at the bottom of the battery chamber and on the battery. The integrated lithium cell 3V has a useful life of 20,000 openings. Before the cell is used, an acoustic signal indicates that the cell should be replaced. If this signal goes unheard, the lock is opened with the residual power and remains opened until the cell is replaced. 101
Page 2 and 3:
2 SISO A/S MILEPARKEN 11 2740 SKOVL
Page 4 and 5:
4 CONTENT MORTISE LOCKS............
Page 6 and 7:
MIC = Master key & Interchangeable
Page 8 and 9:
Application: Drawers, wardrobes and
Page 10 and 11:
Page 12 and 13:
Application: Drawers, wardrobe, cab
Page 14 and 15:
Page 16 and 17:
Application: Hotel mini bars, tills
Page 18 and 19:
Application: Vertical roller shutte
Page 20 and 21:
Accessories for one set: 1 lock 1 h
Page 22 and 23:
Accessories for one set: 1 lock 2 S
Page 24 and 25:
Cam Lock with handle Model No. 323
Page 26 and 27:
Application: Sliding doors Accessor
Page 28 and 29:
Material: Plastic Application: Draw
Page 30 and 31:
Accessories: 1 lock 2 keys 1 cam 1
Page 32 and 33:
Application: Central lock mounted i
Page 34 and 35:
34 CENTRAL LOCK NO. 1018 - ANTITILT
Page 36 and 37:
Application: Central lock mounted i
Page 38 and 39:
CUPBOARD LOCK ”AFRIC” Yellow zi
Page 40 and 41:
Application: Universal left, right
Page 42 and 43:
MODEL 7771 - effective shaft lenght
Page 44 and 45:
PLASTIC ROUND Nickel Plated Matt Fr
Page 46 and 47:
Application: Wardrobes, lockers, ca
Page 48 and 49:
Application: Wardrobes, lockers and
Page 50 and 51: Application: Wardrobes/cabinets Acc
Page 52 and 53: Application: Heave duty drawers, wi
Page 54 and 55: Application: Steel cabinets, locker
Page 56 and 57: Application: Steel cabinets, locker
Page 58 and 59: No. # 22.01.019 Automatic Hook Latc
Page 60 and 61: No. # 14.02.011 Metal Drawer Stop f
Page 62 and 63: Knock in Pivot Stop Zamak for Lock
Page 64 and 65: Short Metal Key with harpoons for k
Page 66 and 67: 66 8,10 R 8 7 1 6 R 8 8,50 120° 8,
Page 68 and 69: 68 CAM PLATES NO. 45-64 16,50 65,50
Page 70 and 71: 70 8,10 R 8 7,20 5,65 6,10 8 59 15
Page 72 and 73: 38,6 36 72 3,2 8,1 16,8 10,2 16,8 6
Page 74 and 75: Application: Glass hinged doors: 4-
Page 76 and 77: Application: Hinged glass doors 4-6
Page 78 and 79: Application: Single glass door, hin
Page 80 and 81: Application: Double glass doors, hi
Page 82 and 83: Application: Double sliding glass d
Page 84 and 85: 84 Application: Double sliding glas
Page 86 and 87: Application: Double sliding glass d
Page 88 and 89: 88 Anti-lift stopper - Plastic Tran
Page 90 and 91: Application: For drawers & cabinets
Page 92 and 93: Application: Metal, wood, plastic,
Page 94 and 95: 94 SOLID BRASS PROFILE CYLINDERS Eu
Page 96 and 97: MORTISE LOCK No. 9045 50 x 90 backs
Page 98 and 99: Function: To open the lock turn the
Page 102 and 103: MOUNTING INSTRUCTIONS 102 17 61 mm
show all

System # 2010

Create successful ePaper yourself

Delete template?

Save as template?