Product catalogue
Product catalogue
Product catalogue
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
SUPPORTS FOR GR PANELS – for applications where<br />
the GR panel cannot be hung on a wall (e.g. in the case<br />
of glass surfaces), a set of chromium plated supports can<br />
be used for the placement of the panels on the fl oor.<br />
The GR panel is inserted into apertures in the supports and subsequently the supports<br />
are affi xed to the panels with the help of adjustment screws. The panel is stable on these<br />
supports; the bottom edge of the panel is 55 mm above the fl oor. For permanent installations,<br />
we recommend that the supports are attached to the fl oor using screws – in the<br />
base there are two openings with a diameter of 6 mm for screws with countersunk heads.<br />
The supports are intended for use only with the GR type and are only for horizontal<br />
installation. In the case of vertical installation (particularly for GR 1000 panels), there<br />
is a signifi cantly higher risk that the user may accidentally knock the panel over. GR<br />
panels on supports must not be exposed to excessive pressure – there is a danger of<br />
tipping if it is placed freely, and if the supports are attached to the fl oor, there is a risk<br />
of damage to the glass in the places where supports are attached.<br />
NOTIFICATION<br />
PRODUCT Cat. No.<br />
Supports for GR panels<br />
Contents of the set: chromium plated supports<br />
– 2 pcs (base diameter 130 mm), plastic covers<br />
for the brackets for the GR panel – 4 pcs, mains<br />
plug (to be installed on the supply lead if the<br />
panel is to be used as a mobile heater)<br />
8000100 TYPE Description Weight [kg] Cat. No.<br />
Simple towel rail (width 500 mm) GR (SET) 300 0,9 5437810<br />
Simple towel rail (width 600 mm) GR (SET) 500 and 700 1,05 5437812<br />
Simple towel rail (width 800 mm) GR (SET) 900 1,2 5437818<br />
Double towel rail (width 500 mm) GR (SET) 300 1,8 5437820<br />
Double towel rail (width 600 mm) GR (SET) 500 and 700 2,1 5437822<br />
Double towel rail (width 800 mm) GR (SET) 900 2,4 5437824<br />
ECOSUN, MR and GR radiant panels are only equipped with a limiting thermostat – suitable regulation is essential for correct and economical<br />
operation; see the chapter THERMOSTATS AND CONTROLS. In the case of GR and GR SET glass panels, the limiting thermostat switches<br />
off the panels at an average temperature of 90 °C, and therefore the real thermal output of the panels is approximately 10 % lower than the<br />
wattage. For this reason and also for the improvement of the dynamics of the whole heating system, we recommend that the installed wattage<br />
is increased by 20 % in contrast with the result of the heat loss calculation. GR and GR SET panels can be supplemented with chromium-coated<br />
supports which enable the panel to be placed on the fl oor – e.g. in proximity to glass surfaces or to create a stylish portable heater.<br />
9<br />
STAINLESS STEEL TOWEL RAIL<br />
– for GR/GR SET 300, 500, 700 and 900 panels<br />
These Towel rail – designed as an accessory for GR and GR SET<br />
radiant glass panels in all colour versions. It is made from a 4×30 mm<br />
polished stainless steel sheet. After its installation, the standard panel is<br />
transformed into a smart bathroom heater with a rail on which a towel<br />
or bath towel can be hung.<br />
The rail is intended only for panels installed vertically; however, the installation itself<br />
is very easy. The openings in the back part of the rail are simply placed onto the top<br />
two screws of the panel by which the heater will be attached to the wall. The panel is<br />
then placed into the prepared hanging brackets. After the attachment nuts have been<br />
tightened, the rail, which is placed between the back part of the panel and the hanging<br />
bracket, is attached fi rmly. The rail is in the shape of a rectangle with the dimensions<br />
530×90 mm; the distance between the attachment openings is 260 mm.