Technical catalogue Technical catalogue - AJ Solutions

General General General description
description
description
The units described in this manual are not built according to ATEX Directive (Explosive atmosphere).
The liquid chillers of “ip” range have been made to meet the needs of industrial processes or plants where the production of
chilled water is required. A variety of models and powers are available to cover a vast range of applications, with inlet water
temperatures between +20°C and 0°C.
Cold water is produced through a refrigerant cycle, as shown in the diagram given later in this catalogue.
Benefits Benefits
Benefits
- “NO “NO-FROST”
“NO FROST” Evaporator
After freezing-up, the performances do not get worse and the water doesn’t
pollute the refrigerant circuit;
- High High C.O.P.
C.O.P.
- Resistant metal works with compressor separation wall
wall
Technical Technical specifications
specifications
Metal Metal Metal works works (mod. (mod. M2 M2 - M4 M4 - M6)
M6)
METAL METAL WORKS WORKS in galvanized sheet steel, stove-enamelled
with polyurethane powders and is equipped with bearing
foot, for fixed installation.
Metal Metal works works (mod. (mod. 10 10 ÷ ÷ 1402)
1402)
METAL METAL WORKS WORKS in galvanized sheet steel, stove-enamelled
with polyurethane powders and is equipped with bearing
foot, for fixed installation.
BASE BASE FRAME FRAME in galvanized sheet steel, stove-enamelled
with polyurethane powders and is equipped with bearing
foot, for fixed installation.
INTERNAL INTERNAL INTERNAL METAL METAL WORKS WORKS in galvanized sheet steel.
DRIP DRIP TRAY TRAY for rain water collection in case of outside
installation, complete with type discharge fitting connectable
without disassembling any panel.
FRAME FRAME is made in anodized aluminium profiles, using
aluminium-alloy angle-joints.
PANELS PANELS in galvanized steel, externally coated with PVC
film. Fastening to aluminium frame by stainless steel
screws, fitted on panel’s edge.
AIR AIR-TIGHT AIR TIGHT GASKETS GASKETS on panels’ edges, made in
polyurethane with dual density (Models Micro2 – Micro4 not
included).
Fans Fans section section
section
EUROKLIMAT EUROKLIMAT Spa Spa
IPE2008_2.0_uk 3
IP IPE IP
AXIAL AXIAL FAN(S) FAN(S) directly coupled to the electric motor, 4 or 6
poles, external rotor type, with special labyrinth watertight,
bearings free from servicing and incorporated thermal
protection. Fans have blades with haul profile, dinamically
and statically balanced and are equipped with accident
prevention grill on air inlet.
Refrigerant Refrigerant circuit circuit
circuit
Refrigerant circuit is completely made in braze welded
copper tube with silver alloy and is insulated on suction part,
to avoid creation of condensate. It is complete with safety
device. For models 502 502 and 1402 1402 the circuit is double and
completely independent. It is mainly composed by:
“ROTATIVE” ROTATIVE” HERMETIC HERMETIC COMPRESSOR
COMPRESSOR, COMPRESSOR for models M2 –
M4 M4 – M6 M6, M6
fitted on antivibration mountings. Electrical motor
is cooled by refrigerant suction gas and is protected against
working anomalies by thermistors embedded in windings.
HERMETIC HERMETIC HERMETIC COMPRE COMPRESSOR COMPRE COMPRESSOR
SSOR ”SCROLL”TYPE ”SCROLL”TYPE for models
from 10 to 201 included, safety valve between suction and
inlet. Electrical motor is cooled by refrigerant suction gas
and is protected against working anomalies by thermistors
embedded in windings for models up to the 81 81 included and
integral electronic protection for models from 101 101 to
201 201.They 201 are fitted on antivibration mountings.