iNLINE FAN rev 1 - Air Systems International

More documents

Recommendations

Info

-4-GENERAL SETUP & OPERATION, EXPLOSION-PROOF MODEL SVF-10EXP1.) Place fan in a clean air environment.Note: Air quality of the confined space should be tested prior to ventilation. If air qualityof the confined space is unacceptable, consult a trained professional.2.) Inspect fan for damaged or worn parts. Inspect all ducting and couplings for air leaks priorto fan operation.3.) Install conductive duct to inlet and/or exhaust flange(s) and tighten cinch strap. Keep bendsand kinks in ducting to a minimum to maximize air flow. The use of conductive ducting isrecommended when operating in potentially explosive environments. Air Systems’conductive ducting is supplied with a 12” ground wire that must be attached to theground lug(s) on the fan and any accessories used in the ventilation system.Note: The SVF series fans are supplied with two 10” to 8”conductive polyethylene adapters. They can be used to attach 8” or10” duct to the air discharge or inlet side of the blower. If the fan isused as a single unit, greater discharge flow will be achieved byremoving the intake duct adapter. Multiple fans can be used inseries to achieve ventilation with long lengths of ducting. Do not usemore than 50ft. of duct on the inlet or discharge side of the fan assevere air flow loss will result. If the blower is to be used in series, afront and rear ground lug is supplied to connect the ground wirefrom the conductive duct on both ends. This will assure a properground and remove potential static electricity buildup.4.) The explosion-proof fan should be fitted with an approved explosion-proof plug to meetClass I, Division I, Groups C and D, Class II, Division I, Groups E, F, and Gspecifications of the electric motor.WARNING! The electric plug should NOT be connected or disconnected in a hazardousenvironment when the receptacle is energized.5.) Connect fan to power source. The on/off switch protrudes through the housing. To turn thefan on, pull switch knob out. To turn off, push switch knob in. The unit is knowoperational.SHUTDOWN• Insure that all workers are removed from the confined space site.• Shut off blower and remove all ducting.MAINTENANCE• Keep blower motor dry and free from contaminants and dust.• Check periodically to ensure moving parts are free from obstructions.GROUND LUG ON FAN HOSINGWARNING: Do not attempt to open or re-wire the sealed electric motor.All explosion-proof approvals will be voided.
REPLACEMENT ITEMS FOR MODELS SVF-10E-5-APPROVED MOTORITEM # DESCRIPTION PART #1 8" T0 10" CONDUCTIVE POLYETHYLENE DUCT TRANSITION SVF-108ADP2 FAN GUARD MGDAXFAN13 INLET/OUTLET GASKET ILF-G4 FAN SVF-FAN5 120 VAC ELECTRIC MOTOR MTR0436 HANDLE SVF-10HNDL7 RUBBER FOOT HDWR0268 CAPACITOR (INSIDE ELECTRICAL BOX) MTRA0899 ON/OFF SWITCH ELSW038R10 POWER CORD ELCB01211* 120 VAC ELECTRIC MOTOR AND CAPACITOR KIT SVF-10E-MA* NOT SHOWN ON DRAWINGWARNING:FOR HAZARDOUS ENVIRONMENTS, ALWAYS USE AIR SYSTEMS’ MODEL SV-CUPCNDCONDUCTIVE SADDLE VENT® VENTILATION KIT WITH AN EXPLOSION-PROOFOR PNEUMATIC BLOWER.
Page 1: Models/Modelos/ModèlesSVF-10E, SVF
Page 6 and 7: -6-REPLACEMENT ITEMS FOR MODELS SVF
Page 8 and 9: -8-TROUBLESHOOTINGPROBLEM POSSIBLE
Page 10 and 11: -10-CONFIGURACIÓN GENERAL Y OPERAC
Page 12 and 13: -12-ARTÍCULOS DE REEMPLAZO PARA MO
Page 14 and 15: -14-SOLUCIÓN DE PROBLEMASPROBLEMA
Page 16 and 17: -16-Exclusión de GarantíaEl equip
Page 18 and 19: -18-INSTALLATION ET FONCTIONNEMENT,
Page 20 and 21: -20-PIÈCES DE RECHANGE POUR LES MO
Page 22 and 23: -22-DÉPANNAGEPROBLÈME CAUSE POSSI
Page 24: -24-Limitations de la garantieLes a

iNLINE FAN rev 1 - Air Systems International

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?