Bedienungsanleitung, Manuel, Manual, Manuale, 4116, PR ...

More documents

Recommendations

Info

Outside range readout (IN.LO, IN.HI): If the valid range of the A/D converter or the polynomial is exceeded Input Range Readout Limit VOLT 0...1 V / 0.2...1 V 0...10 V / 2...10 V IN.LO IN.HI IN.LO IN.HI < -25 mV > 1.2 V < -25 mV > 12 V CURR 0...20 mA / 4...20 mA IN.LO IN.HI < -1.05 mA > 25.05 mA LIN.R 0...800 Ω 0...10 kΩ IN.LO IN.HI IN.LO IN.HI < 0 Ω > 1075 Ω < 0 Ω < 110 kΩ POTM - IN.LO IN.HI < -0.5 % > 100.5 % TEMP TC / RTD IN.LO IN.HI < temperature range -2°C > temperature range +2°C sensor error detection limits Error indications 46 Sensor error detection (SE.BR, SE.SH): Input Range Readout Limit CURR Loop break (4..20 mA) SE.BR = 21 mA POTM All, SE.BR on all 3-wire SE.BR > ca. 126 kΩ LIN.R 0...800 Ω 0...10 kΩ SE.BR SE.BR > ca. 875 Ω > ca. 11 kΩ TC SE.BR > ca. 750 kΩ / (1.25 V) TEMP Display readout below min.- / above max. (-1999, 9999): Input Range Readout Limit All All -1999 9999 Display readout 9999 RTD, 2-, 3-, and 4-wire No SE.SH for Pt10, Pt20 and Pt50 Readout at hardware error SE.BR > ca. 15 kΩ SE.SH < ca. 15 Ω Error search Readout Error cause Test of internal CJC sensor CJ.ER CJC sensor defect or temperature outside range Checksum test of the configuration in FLASH FL.ER Error in FLASH Check measurement of analogue output current AO.ER 1) No load on the current output (only S4...20/S20...4 mA) Communications test 4501 / <strong>4116</strong> NO.CO Connection error Check that input signal matches input configuration IN.ER 1) Error levels on input Check that saved configuration in 4501 matches device TY.ER Configuration is not <strong>4116</strong> ! Error indications in the display flash once per second. The help text explains the error. 1) The error is reset by switching off and then switching on the supply voltage to the device.
Supply: 31 32 33 TC, internal RTD, 2-wire RTD, 3- / 4-wire CJC sensor Resistance, 2-wire 41 42 43 44 41 42 43 44 41 42 43 44 41 42 43 44 Resistance, 3- / 4-wire 41 42 43 44 Voltage 41 42 43 44 - + Current Voltage, 1 V Voltage, 10 V Relays 11 12 13 14 11 12 13 14 11 12 13 14 21 22 23 24 - mA + - V + + Potentiometer 2-wire transmitter Current 41 42 43 44 41 42 43 44 41 42 43 44 *TC, CJC connector 41 42 CJC 44 - Tx + - V - + ConnECTions - inputs: outputs: * Order separately: CJC connector 5910 + - + R1 R2 47
Page 1 and 2: 4 1 1 6 U n i v e r s a l T r a n s
Page 3 and 4: UnivERsal TRansMiTTER PReasy 4116 i
Page 5 and 6: signaTURFoRKlaRing Trekant med udr
Page 7 and 8: EF-ovEREnssTEMMElsEsERKlÆRing Som
Page 9 and 10: UnivERsal TRansMiTTER PReasy 4116
Page 11 and 12: Indgangssignaler: Strøm + + aPPliK
Page 13 and 14: EMC-immunitetspåvirkning .........
Page 15 and 16: Følerfejlsdetektering ............
Page 17 and 18: Forsyning: 31 32 33 TC, intern RTD,
Page 19 and 20: PRogRaMMERing / bETjEning aF TRyKKn
Page 21 and 22: Latch-funktionen kan vælges separa
Page 23 and 24: valg af units Efter valg af indgang
Page 25 and 26: 999.9 -199.9 1 2 3 100.0 DISP.HI Tx
Page 27 and 28: 3 3 HOLD CLOS OPEN NONE 1 2 NONE ER
Page 29 and 30: Til setup menu 40.0 3 Rx.LATC Txt 6
Page 31 and 32: [49] Kalibrer indgang lav til proce
Page 33 and 34: grafisk afbildning af latchfunktion
Page 35 and 36: UnivERsal TRansMiTTER PReasy 4116 C
Page 37 and 38: syMbol iDEnTiFiCaTion Triangle with
Page 39 and 40: As manufacturer EC DEClaRaTion oF C
Page 41 and 42: UnivERsal TRansMiTTER PReasy 4116
Page 43 and 44: Input signals: Current + Volt - age
Page 45 and 46: EMC immunity influence ............
Page 47: Sensor error detection ............
Page 51 and 52: ConFigURaTion / oPERaTing ThE FUnCT
Page 53 and 54: is deactivated manually. The latch
Page 55 and 56: selection of units After choosing t
Page 61 and 62: To setup menu 40.0 3 Rx.LATC Txt 65
Page 63 and 64: [49] [50] [51] [52] [53] [54] [55]
Page 65 and 66: graphic depiction of latch function
Page 67 and 68: TRansMETTEUR UnivERsEl PReasy 4116
Page 69 and 70: signiFiCaTion DEs syMbolEs Triangle
Page 71 and 72: DEClaRaTion DE ConFoRMiTE CE En tan
Page 73 and 74: TRansMETTEUR UnivERsEl PReasy 4116
Page 75 and 76: Signaux d’entrée : Courant + Ten
Page 77 and 78: Immunité CEM .....................
Page 79 and 80: Détection erreur capteur .........
Page 81 and 82: Alimentation : 31 32 33 TC, capteur
Page 83 and 84: PRogRaMMaTion / oPERaTion DEs ToUCh
Page 85 and 86: jusqu’à désactivation manuelle.
Page 87 and 88: sélection des unités Après avoir
Page 93 and 94: R1 - mise à zéro 1 2 3 40.0 1 000
Page 95 and 96: [47] [48] [49] [50] [51] [52] [53]
Page 97 and 98: illustration graphique de la foncti
Page 99 and 100:
UnivERsal-MEssUMFoRMER PReasy 4116
Page 101 and 102:
ZEiChEnERKlÄRUngEn Dreieck mit aus
Page 103 and 104:
Eg-KonFoRMiTÄTsERKlÄRUng Als Hers
Page 105 and 106:
UnivERsal-MEssUMFoRMER PReasy 4116
Page 107 and 108:
Eingangssignale: Strom + Span- Pote
Page 109 and 110:
EMV Störspannungseinfluss ........
Page 111 and 112:
Fühlerfehlererkennung ............
Page 113 and 114:
Versorgung: 31 32 33 WTH, 2-Leiter
Page 115 and 116:
KonFigURaTion / bEDiEnUng DER FUnKT
Page 117 and 118:
einen Alarmzustand. Die Verriegelun
Page 119 and 120:
selbstdiagnose Das Gerät führt ei
Page 121 and 122:
999.9 -199.9 1 2 3 100.0 DISP.HI Tx
Page 123 and 124:
3 3 HOLD CLOS OPEN NONE 1 2 NONE ER
Page 125 and 126:
FlUssDiaMgRaMM Manuelle Deaktivieru
Page 127 and 128:
[48] [49] [50] [51] [52] [53] [54]
Page 129 and 130:
grafische Darstellung der verriegel
Page 131 and 132:
Displays Programmable displays with
show all

Bedienungsanleitung, Manuel, Manual, Manuale, 4116, PR ...

Create successful ePaper yourself

Delete template?

Save as template?